Drum chipper

Bruks 1202 CS6

Condition: excellent (used), Storti RM 500 edger - Italian production Nljdpjk Talpjfx Aaaja - year of production 1993 - electric spacing of discs TECHNICAL PARAMETERS: - cutting width max 435 mm - cutting height max 170 mm - engine power 2 x 22kW - max element width 600 mm - minimum material length 800 mm - max disc diameter 600 mm - spindle diameter 40 mm - two upper pulling rollers - one upper pressure roller - roller motor power 2 x 1.1 kW - roller pressure with automatic jump - seven bottom pulling toothed rollers - electric disc adjustment - two lasers - feed speed 25 and 50 m/min - feeding table 2950 mm - receiving table 3000 mm - drive rollers D100 mm - power of the roller feed motor 2 x 1.5 kW Transport dimensions 500x240x180 cm weight 3500 kg

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. Nlsdowp Rqfepfx Aaasa SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Condition: ready for operation (used), Pressing force: approx. 700 kN (approx. 70 tons) Motor power: approx. 11 kW Power supply: 3 × 400 V / 50 Hz Nlsdpfx Aajra Dddsaja Single bale weight: up to approx. 600 kg Bale dimensions: approx. 1100 × 1100 × 1200 mm Machine dimensions: approx. 5.9 m length, 2.5 m width, approx. 2.6 m height Machine weight: approx. 7 tons Cycle time: approx. 45–47 s Construction features: - Large loading opening for cardboard - Possibility of automatic feeding (e.g., via conveyor) - Manual wire tying (4 wires) - Pallet lock and hydraulic doors for bale removal Advantages of this press: - Large bales – fewer transports - High pressing force - Designed for continuous operation Available production years: 2016–2020

Condition: refurbished (used), Completely refurbished Bongioanni CRL 4 tensioning wagon with clamping blocks. Track gauge 1200 mm. Rails newly milled. Servo-electric drive. Sale upon customer order. Nlsdpsxtwxbefx Aaaja

Condition: reconditioned (used), functionality: fully functional, approx. 4.5 m long infeed and centering table Drive via chain from the feed motor Centers the logs in the middle of the rotor Debarking machine VK 26 Njdou Hmacepfx Aaajla 4 main cutters 4 pre-cutters 30 KW main motor 11 KW feed unit non-driven extraction table Machine workshop checked Machine cleaned and repainted

Condition: new, power: 90 kW (122.37 HP), Year of construction: 2026, A double rotor hammer crusher is a type of crusher in which two rotors are mounted on a single shaft, combined to form a spinning rotor. The double rotor arrangement enhances the crushing capabilities and provides a more efficient and reliable crusher design compared to single rotor crushers. Here are some key features and aspects of a double rotor hammer crusher: Nlodpfx Aasq Nf Eneaoa 1. Two Rotors: As the name suggests, the crusher has two rotors that rotate in opposite directions on a common shaft. This dual rotor configuration allows for increased impact and crushing power. 2. High Capacity: The dual rotor design enables the crusher to handle larger feed sizes and higher capacity compared to single rotor crushers. It is suitable for crushing materials with high hardness and large sizes. 3. Versatility: Double rotor hammer crushers are versatile and can be used in various applications, including the reduction of limestone, gypsum, coal, and other similar materials in the mining, cement, and building materials industries. 4. Impact Crushing: The primary mechanism of crushing in a double rotor hammer crusher is through the impact of the hammers against the material. The material is fed into the crusher, and the high-speed rotating hammers impact and shatter the particles. 5. Adjustable Gap Settings: These crushers often have adjustable gap settings between the rotors and the impact bars, allowing control over the final particle size. 6. Durability: The robust design of the double rotor hammer crusher makes it durable and capable of handling tough materials and continuous operation. 7. Reduced Wear: The dual rotor arrangement can help distribute wear more evenly across the hammers and other wear parts, potentially extending the overall lifespan of the crusher. Typical Technical Specifications While exact numbers vary by manufacturer, these are the standard ranges for industrial models: Model (Rotor Size),Max Feed Size,Output Size,Capacity (t/h),Total Motor Power 600 × 400,≤110 mm,≤3 mm,10 – 15,18.5+18.5 kW 800 × 600,≤120 mm,≤3 mm,40 – 50,45+45 kW 800 × 800,≤180 mm,≤3 mm,50 – 60,45+55 kW 1000 × 800,≤180 mm,≤3 mm,70 – 80,75+55 kW 1100 × 1000,≤200 mm,≤3 mm,70 – 100,90+110 kW 1400 × 1200,≤200 mm,≤3 mm,90 – 110,132+160 kW For more details about double stage hammer crusher, or double rotor crusher, welcome to leave us a message, our team will get back to you at the earlist.

Condition: refurbished (used), FULL LINE of Drilling, max working width mm 3200, with fast automatic handling equipment. Composed of the following machines: A) LOADER (Portal) "RBO" Winner C 3200 with double pick-up and central motorized rollers table. With 2 on-ground motorized rollers ways to in-feed the piles (stacks) of panels to loader. B) TRANSFER (Connecting Rollers Table with 90° conveyoring belts) “RBO” Mod. Transfer TA 90° C) 1st Auotmatic BORER "BIESSE" Mod. Techno FDT with No. 2 Horizontal Units + No. 7 Vertical Bottom Units D) 2nd Automatic BORER "BIESSE" Mod. Techno FDT with No. 2 Horizontal Units + No. 7 Vertical Bottom Units E) TRANSFER (Connecting Rollers Table with 90° conveyoring belts) “RBO” Mod. Transfer TA 90° G) UNLOADER-STACKER (Portal) "RBO" Winner SC 3200 with double pick-up, with double storage station, with central motorized rollers table. With 2 on-ground motorized rollers ways to out-feed the piles (stacks) of panels from the Unloader Nledpfx Aaedfgg Ioaoa

Year of construction: 1988, condition: repair required (used), mechanisation for planer infeed -For lengths up to ca. 13 m -Ideal unit for KVH (solid construction timber)and BSH (laminated beams) in front of the planer -1 operator -lateral destacking unit -separation Nsdpfevbtpjx Aaajla -4 cross cut saws -cutting cross section 180x220 mm, 150x300 mm

Condition: excellent (used), CPM 2000 granulator, 90kW engine die diameter 410mm We have several pieces Nodpewcdpnofx Aaajla

Condition: good (used), Manufacturer: Haver & Boecker Documentation available Mechanical conversion from 50 kg to 25 kg bags in 1999 Control system: Siemens S7 Nlsdsv Sz Tdjpfx Aaaja Upgraded to the latest standard with spare parts support in 2015 Supported bag types: Quicklime, hydrated lime, cement, gypsum