Multi-spindle drilling machine

BIESSE F 39 E

Condition: used, Year of construction: 2000, With electric height and tilt adjustment Used, excellent condition, little used Make Altendorf Type F45 Year of manufacture 2000 Machine number GS-tested Motor 4 kW Steel guides Carriage length approx. 3000 mm Cutting width approx. 1050 mm Pivoting up to 45° Prepared for scoring unit Parallelogram guard Tabletop extension Nlodpfx Akovxlq Hjieh Anodized aluminum parts Electric height adjustment Electric tilt adjustment Digital display: - Cutting angle - Speed Extraction connection D 120/80 mm Space required approx. 3010 mm x 1800 mm x 1500 mm Weight approx. 1000 kg Storage location 97447 Gerolzhofen, free on load, unpacked Sold in the current condition as seen, without warranty or guarantee

Condition: refurbished (used), Year of construction: 2024, Overhauled: 2024 Control: SPS Siemens S7 Saw blade max: 500 mm motor power 4,0 KW Saw blade feed: 0-40 mm/ s continuously adjustable Saw height control electronic Working range square 90° max.: 130 x 130 mm Working range flat 90° max.: 190 x 130 mm Working range round 90° max.: 170 mm The machine has been completely overhauled in our company and is in mint condition. Among other things, the following points were renewed: Conversion to Siemens S7 PLC control Conversion to Siemens HMI user interface Conversion to pusher with servo control New electrical components New pneumatic lines New pneumatic components Conversion to valve terminal Optimization of the suction capacity New minimum lubrication system Replacement of general wear parts Overhaul of the cab The machine also has Minimum quantity lubrication Splitting extension (for a high-quality cutting surface without return marks) Pre-loading magazine for gentle handling of painted/anodized surfaces Offcut ejector in the pusher Foldable offcut tray Optional: Magazine width 3000mm Pusher length 6000mm Pusher length 8000mm Reinforced motor 5.5 kW Mass clamping device for parallel sawing of several workpieces Online support connection Nodpsuiy Ngofx Akislh Delivery and installation on your premises Training of your employees

Condition: used, Year of construction: 1996, pressure 80 t throat 320 mm stroke 6 - 118 mm no. of strokes 30 - 80 Hub/min ram adjustment 70 mm table surface area 830 x 610 mm ram surface 650 x 400 mm Njdpfstycdkjx Akislh column daylight (nach hinten) 630 mm total power requirement kW weight of the machine ca. 8,1 t dimensions of the machine ca. B 1,2 x T 1,9 x H 3,3 m Furnishing: - with gear transmission - fixed table - automatic stroke adjustment - automatic ram adjustment - hydr. Overload - Ejector - Grease central lubrication - Cover plate for drainage hole - Continuous speed control using a frequency converter - Machine is technically checked in our company and receives a new control cabinet with safety controls and touchscreen - current UVV test with braking time measurement

Condition: excellent (used), functionality: fully functional, POINT TO POINT BORING machine with CN model MASTERWOOD SPEEDY 207 second hand machine for custom furniture manufacturing, kitchen furniture, bathroom furniture, and various processes Boring head with 5 independent vertical chucks and 1 double horizontal chuck Saw for longitudinal cuts Machine table with 1390 x 750 mm boring capacity and two side jump up stops handled by the control unit to execute with only one program and one intermediate hold panels up to 2800 x 750 mm size Possibility of boring 2800 mm panels Pneumatic tool displacement mm 60 Nodpfx Akjwd Irvoislh Max panel thickness mm 50 Spindles rotation rpm 4500 Saw rotation rpm 6000 Vacuum pump motor Hp 1,5 Vacuum cup diameter mm 80 Front stop complete with 4 locking cylinders for drilling narrow workpieces and strips Multitasking control complete with interactive graphic programming, 9" video, boring programs, optimizing working cycle, graphic, parametric, diagnostic modes Overall dimensions - Machine : mm 2500 x 1800 x 1800 h - Weight kg 850 Overall dimensions - Electric board : mm 800 x 520 x 1200 - Weight Kg 120

Condition: excellent (used), Angular sawing plant Numerical Control OSI Plus - Software Optiplanning N. 2 Pre-loading roller tables (mm) approx. 4500 x 2200 each Lifting table (mm) 4500 x 2200 1° Rear-pusher, with No. 5 clamps/grippers Turning device (rotating unit) at 90° 1° Panel saw (longitudinal) max. cutting width (mm) 4500 Max blade projection (mm) 152 Scoring Unit (max. diameter saw) mm approx. 215 Main Sawing Unit (max. diameter saw / power) mm 530 ( Kw 30) Adjustable speed of the saw carriage (m/min) 1 - 170 m/min Cutter for shredding trimmings Nljdoukhd Aepfx Akijh 2° Rear-pusher, with No. 10 clamps/grippers 2° Panel Saw - Max cutting width mm 2200 Max blade projection (mm) 152 Scoring Unit (max. diameter saw) mm approx. 215 Main Sawing Unit (max. diameter saw / power) mm 530 (Kw 30) Adjustable speed of the saw carriage (m/min) 1 - 170 m/min No. 2 Front supporting tables with Air blowing system mm 2200 x 1500 Automatic unloader (bridge) for cut panels "RBO (BIESSE)" Mod. Lifter with 6 stacking stations

Condition: used, pressure 55 t throat 250 mm stroke 10-90 mm table-size 640 x 495 mm no. of strokes 120 Hub/min ram adjustment 55 mm ram surface 290 x 210 mm ram hole 40 H7 mm hole in the table 220 x 190 mm T-slots 22 clamping plate 620 x 485 x 65 mm total power requirement 4,5 kW Nljdpscp Apyofx Akijh weight of the machine ca. 3,4 t dimensions of the machine ca. 1,5 x 1,2 x 2,2 m

Condition: used, Single-column – Eccentric press WEINGARTEN Type EV 63 Machine No. 738 / 61 Year of manufacture 1962 Pressing force 63 tons Stroke 260 mm Table area 630 x 530 mm Table opening Ø 210 mm Slide area 315 x 260 mm Adjustable slide stroke 8-100 mm Slide adjustment 63 mm Tool holder bore Ø 40 mm, with clamping piece Installation height max 450 mm Stroke rate 115 strokes / min Compressed air requirement min. 4.5 bar Motor power 4 kW Power connection 380 Volt, 50 Hz Nedpfx Ajk S Htxskijlh Table height above floor approx. 750 to 900 mm - Electrical stroke release via foot switch or two-hand control - Overload protection by shear plate - Clutch-brake combination by WEINGARTEN friction-thread clutch with top dead center through-drive protection - Front crankshaft support bearing - Press table adjustable in height via 2 threaded spindles - Manual centralized lubrication - Control cabinet positioned beside the press - UVV (German trade association for accident prevention) for manual feeding operations Space requirement L x W x H 1750 x 1600 x 2430 mm Weight 4.5 tons Good condition

Condition: new, pressure 25 t throat 200 mm stroke 4 - 80 mm table-size 520 x 400 mm no. of strokes 160 Hub/min work capacity during endurance run 1370 Nm Nedpfxjb U Hwne Akielh force 2740 Einzelhub adjustment of stroke 4 - 80 mm ram adjustment 40 mm ram surface 160 x 160 mm hole in the table 200 x 150 mm clamping plate 500 x 380 x 60 mm hole in the table 80 mm weight of the machine ca. 1,9 t

Condition: used, Holz Her Perfect 1422 K + PU Heavy-duty version, for edge banding up to 20 mm thickness Fully automatic roller magazine – crosscut shear Fully automatic edge magazine for strip material Cartridge + PU gluing station Flush trimming Nodpfx Akjy Rm Iioislh Multifunction milling unit, flush – chamfer – radius milling with mechanical digital adjustment Soundproof enclosure CE-compliant design Machine is FUNCTIONALLY TESTED and in VERY GOOD CONDITION available ex-stock Lieboch

Condition: not inspected (used), Tenoning spindle 2 St. Number of milling agregates 7 St. Spindle diameter 50 mm control Weinig, PC-Nexus Weinig Unicontrol 12 with radial and axial CNC spindles as well as VARIO table and milling carriage ..... Machine dismantled professionally and in our warehouse in 73447 Oberkochen. Video and pictures were taken before dismantling. Technical data summary (please inquire about any additional accessories included) ..... crosscut saw ..... > Electronic crosscut saw, horizontally infinitely adjustable > Number of tools: 1 piece. > Spindle speed: 2,800 rpm > Spindle diameter: 40 mm > Tool diameter max.: 400 mm > Motor power: 3.7 kW > Laser directional light to detect the saw section > Axial adjustment path 150 mm NC axis, electronically infinitely variable > Radial pneumatic adjustment path 8 positions for e.g. edge rounding from above Rounding aggregate ..... > Position: horizontally below > Motor power: 1.5 kW > Spindle diameter: 20 mm > Tool clamping length: 25 mm > Spindle speed: 9,000 rpm > Tool diameter: max. 130 mm > Axial adjustment path mechanically coupled with crosscut saw. > Radial adjustment pneumatically controlled on/off electronic length stop ..... > Length 4500 mm 1. Tap and slot spindle ..... > Number of tools: variable > Motor power: 15 kW > Spindle diameter: 50 mm > Tool clamping length: 640 mm, with counter bearing > Axial adjustment path: 580 mm NC axis, continuously variable > Spindle speed: 2,800 rpm > Tool diameter: max. 400 mm > Overtravel counter, complete clamping length is countered 2. Tap and slot spindle ..... > Number of tools: variable > Motor power: 15 kW > Spindle diameter: 50 mm > Tool clamping length: 640 mm, with counter bearing > Axial adjustment path: 580 mm NC axis, continuously variable > Spindle speed: 2,800rpm > Tool diameter: max. 400 mm > Overtravel counter, complete clamping length is countered Transfer tape ..... Included for transferring the parts to longitudinal machining Separation of double parts before the start of longitudinal processing. 1. Profiling spindle (synchronous and counter-rotation) Njdpfx Aksx H Al Noislh ..... > Position: vertical right > Number of tools: variable > Motor power: 11 kW > Spindle diameter: 50 mm > Tool clamping length: 400 mm, with counter bearing > Axial adjustment path 350 mm NC axis, infinitely variable > Radial adjustment path 80 mm NC axis, infinitely variable > Spindle speed: 6000 rpm > Tool flight circle min.: 140 mm > Tool flight circle max.: 232 mm > 2 feed rollers axially pneumatically controlled opposite the spindle, 8 positions > Table top pneumatically controlled to the tool diameter 2. Profiling spindle ..... > Position: vertical right > Number of tools: variable > Motor power: 11 kW > Spindle diameter: 50 mm > Tool clamping length: 400 mm, with counter bearing > Axial adjustment path 350 mm NC axis, infinitely variable > Radial adjustment path 80 mm NC axis, infinitely variable > Spindle speed: 6000 rpm > Tool fli...