Condition: new, Number of sanding units 2 St. sanding width 290 mm Sanding height max. 180 mm LÖWER-DoubleSander Solid DSM 3000 ----- Two-sided single wood sander for sanding Solid wood such as window wood etc. Stable Top version with long casting tables, brushing and finishing device and conveyor belt feed. Suitable for high Permanent load even with higher chip removals. - Staggered sanding and finishing units at the top and below - directly driven rubberized sanding rollers for slip-proof free power transmission - Combined grinding via roller and shoe for high chip removal with a flat intervention zone at the same time Dedpjyrty Tefx Acxski - maintenance and wear-free CERMET-coated grinding wheels shoes with very good thermal conductivity and absolute Dimensional accuracy - External cooling of the grinding zones for cooler grinding and longer sanding belt service life - force-guided pneumatically controlled sanding belt oscillation - effective sanding dust extraction directly on the Grinding rollers - Airborne dust extraction on the tension rollers - Integrated brushing and finishing device with large Grinding dust extraction - motorized grinding thickness adjustment via precision threaded spindles and large-sized linear ball screws bearing sets on hardened and ground precision shafts with dust and dirt protection - Adjustment of the chip removal at the bottom via precision Threaded spindle with dimension display via scale ring (Resolution 0.1mm) - Sanding belt tension via pneumatic cylinder constant clamping pressure - Sanding belt change with pneumatic belt relaxation Within seconds - Adjustment option for the sanding belt run Band change - electro-pneumatic compressed air monitoring - Anti-running protection via contact roller if it is too thick workpieces - Workpiece transport via calibrated non-slip and non-stick fixed conveyor belts over heavy, 1000mm long cast iron tables with a finely planed surface and spring-loaded Pressure rollers with fine adjustment - Cardan shaft drive for smooth and consistent Workpiece transport - Feed gear motor infinitely variable for quick adaptation to different types of wood - all motors electrically protected - Ergonomically arranged controls on the workpiece inlet side - digital thickness display (resolution 0.1mm) with modern Magnetic tape system Technical data: - Sanding belt speed 22 m/s - Sanding belt length 1800mm - Sanding belt width 300mm - Working width 290mm - Grinding thickness 2-180mm - two brake motors for 7.5 kW drive - Feed motor 1.0 kW - Feed speed 4-20 m/min. - automatic height adjustment 0.37 kW - two brush units of 0.37 kW each with fiber brushes D 120 x 300mm - Suction nozzles 2 x 120mm and 2 x 150mm - Pneumatic connection 6 bar - Working height 850mm - Length 2105mm - Length with control panel 2490mm - Width 980mm - Height 1910mm - Weight approx. 1650 kg - Operating voltage 400 volts, 50 Hz, 3P - CE version ----- Price of the above machine on request! ----- Special accessories with additional costs: Workpiece blow-off - using nozzles from above and below at the machine outlet arranged, pneumatically controlled Sanding belt blowout via nozzles directly on the radii of the tension rollers inside the suction arranged, timer controlled on/off 5 seconds each, can be switched on separately Disc unit for defibering - two gr...

Condition: new, Number of sanding units 4 St sanding width 190 mm Sanding height max. 2 - 180 mm LÖWER - DoubleMaster DSM 2000 DB ----- Double-sided single wood sander with additional Dedjyrty Hjpfx Acxjki Transverse brush sanding unit (discs) and Longitudinal brush sanding unit (roller) for sanding Solid wood such as B. window wood etc. Stable top version with long cast tables and Conveyor belt feed. Suitable for high continuous loads even with higher chip removals. 1. Belt sanding unit with CERMET sanding shoe pre-sanding 2. Disc aggregate cross grinding for defibering 3. Rolling aggregate longitudinal grinding for directional finish Direction of growth - Staggered sanding and finishing units at the top and below - directly driven rubberized sanding rollers for slip-proof free power transmission - Combined grinding via roller and shoe for high chip removal with a flat intervention zone at the same time - maintenance and wear-free CERMET-coated grinding wheels shoes with very good thermal conductivity and absolute Dimensional accuracy - External cooling of the grinding zones for cooler grinding and longer sanding belt service life - force-guided pneumatically controlled sanding belt oscillation - effective sanding dust extraction directly on the Grinding rollers - Airborne dust extraction on the tension rollers - integrated brush grinding device (transverse and Longitudinal) with sanding dust extraction - motorized grinding thickness adjustment via precision threaded spindles and large-sized linear ball screws bearing sets on hardened and ground precision shafts with dust and dirt protection - Adjustment of the chip removal at the bottom via precision Threaded spindle with dimension display via scale ring (Resolution 0.1mm) - Sanding belt tension via pneumatic cylinder constant clamping pressure - Sanding belt change with pneumatic belt relaxation Within seconds - Adjustment option for the sanding belt run Band change - electro-pneumatic compressed air monitoring - Anti-running protection via contact roller if it is too thick workpieces - Workpiece transport via calibrated non-slip and non-stick fixed conveyor belts over heavy, 1000mm long cast iron tables with a finely planed surface and spring-loaded Pressure rollers with fine adjustment - Cardan shaft drive for smooth and consistent Workpiece transport - Feed gear motor infinitely variable for quick adaptation to different types of wood - all motors electrically protected - ergonomically arranged controls on the Workpiece inlet side - digital thickness display (resolution 0.1mm) with modern Magnetic tape system Technical data: - Sanding belt speed 22 m/s - Sanding belt length 1800mm - Sanding belt width 200mm - Working width 190mm - Grinding thickness 2-180mm - two brake motors for 5.5 kW drive - Feed motor 1.0 kW - Feed speed 4-20m/min. - automatic height adjustment 0.37 kW - Brush sanding units Disc D=max. 200mm Roller D=max. 270mm - Suction nozzles 2 x 120mm and 2 x 180mm - Pneumatic connection 6 bar - Working height 870mm External dimensions: - Length 2600mm - Length with wheels 2985mm - Width 880mm - Height 1910mm - Weight approx. 1500 kg - Operating voltage 400 volts, 50 Hz, 3P - CE version ----- Price of the above machine on request! ----- Special accessories with additional charge: Workpiece blow-off - ...

Year of construction: 2026, condition: new, max. tool diameter 400 mm 0 180 mm operating pressure 2 bar ROTATHERM chamber washing systems are used in all areas of industry and Craftsmanship for cost-effective cleaning of a wide variety of items to be cleaned and materials used. The parts are cleaned like in a dishwasher. Inserted into one Wire mesh basket they are in the closed device with a hot Lye shower washed from all sides. The machine will be selected after the Temperature and washing time set in operation. A centrifugal pump promotes the Washing water circulates to the nozzle system, which at the same time moves the basket in offset rotation. (Optional electric basket drive) After the cleaning process is complete, the device switches off automatically. the Parts can also be removed beforehand. In this case, when lifting the the pump is automatically put out of operation. ROTATHERM chamber washing systems are available in various sizes and at short notice Designs are available and can be requested on special claims be modified. As a rule, water-based cleaners are used deployed. But solvents are also used in ours cleaning machines. If necessary, the systems can be ex-protected version are delivered. Technical details EMSA ROTATHERM Mini: ----- Basket diameter: 400 mm Usable height: 180 mm Load capacity: 50kg Spray pressure without / with filter: 1.5 / 2.3 bar Circulation volume: 2.5 m³/h Tank capacity: 35 l Heating power: 2 kW Connected load: 2.5 kW Voltage: 220/230V Frequency: 50Hz Dimensions ----- Depth: 530mm Width: 650mm Height: 630mm Weight: 48kg ----- Price of the basic machine in the above design: On request! ----- Accesories: ----- Order No.: 1.521 Raised lid/max. Tool length 310 mm Dksdpjyrtytsfx Acxoi Order No.: 1.522 HSK 63 F tool holder for changing with basket Order No.: 1.523 HSK 63 E tool holder for changing with basket Order No.: 1.524 Tool holder for Weinig Powermat to change with basket Order number: 2.006 small parts basket, Order number: 1.504 filter system (0.08m²), Order number: 1.510 pressure gauge, Order No.: 1.511 Electromotive basket drive, Order number: 1.512 mobile frame, Order number: 1,513 rolls, Order number: 1.514 suction device, Order number: 1.516 oil separator / belt skimmer, Order number: 1.518 system completely in stainless steel, Order number: 1.519 nozzles in stainless steel, ----- Price on request The ROTAHTERM tool washing machine is also available in larger versions Standard, Maxi and XL available. All devices are also available in special voltages. Surcharge on request. When ordering accessories, the specified technical data and possibly the delivery time! The values ??given are guide values. Construction changes reserved. Delivery time: short term and after Agreement. All prices ex works plus packaging, transport, insurance and legal VAT. (technical information according to the manufacturer - without guarantee!)

Condition: used, 0 ja_yes Striffler sash Fitting Table ----- Dedpjyn R Iyefx Acxjki - with automatic screwdriver and screw feeder - Fitting rack - Punch for Roto fittings (Technical specifications according to the manufacturer, without guarantee!)

Year of construction: 1997, condition: used, Number of sanding units 1 st. sanding width 140 mm Sanding height max. 120 mm LÖWER Molding Intermediate Sanding Machine Model LZ 2 For finishing and intermediate sanding of all types of moldings. Particularly fast processing thanks to simultaneous sanding of several moldings side by side. Conveyor belt feed with table extension under the sanding roller. 1 roller unit from above, working width 140 mm, table length 1100 mm, Workpiece thickness adjustment 2 - 120 mm with numerical display, Drive motor 2.2 kW at 1,430 rpm, mandrel 32 mm, Three feed speeds: 6, 12, and 16 m/min, Infeed contact, extraction ports 2 x 100 mm, Operating voltage 400 V, 50 Hz, 3 Ph, air connection 6 bar. NOTE VIDEO: Dkedpfjyn R Itsx Acxji Video NOT original. Shows machine type of the same model from our archive. (Technical data according to the manufacturer - without guarantee!)

Condition: used, Year of construction: 2006, Tenoning spindle 2 St. Number of milling agregates 5 St. Spindle diameter 50 mm SCM Windor 40 R window production centre, manufactured in 2006 ----- This machine is part of the sale of a complete window manufacturing operation, see stock number 1305-6979. Machines still connected and ready for demonstration Technical Summary: ----- Dksdjyn R Imjpfx Acxji - 2 long CNC-controlled slotting spindles - Optima 16: Drilling units for face and longitudinal drilling - ROTATEN: Angled window attachment - 3 long CNC-controlled profile spindles + top and bottom unit - Rebating carriage for small sashes - Workpiece return Options with additional costs: ----- - Used Leitz window and door tools for SCM Windor 40 R. Price: €10,000 - Separate OKOMA UF 3 rebating machine with compatible tools for SCM Windor 40 R systems. Price: €2,000 - Used chip extraction and filtration system for SCM Windor 40 R (See attached PDF for more information). Price 5.500 Euro (Technical specifications according to the manufacturer, without guarantee!)

Year of construction: 2022, condition: used, Number of sanding units 6 st. sanding width 45-165 mm Sanding height max. 45-92 mm weight 2200 kg Ecoline Q-SAND 6 For sale on behalf of a customer ----- Full text as PDF attachment! Short description: Machine with infeed conveyor and automatic height detection. It has two grinding discs on top and two grinding discs on the bottom, each connected to a brush unit. Dedpfsxyafkex Acxjki Technical manufacturer's description: Ecoline Q-Sand: the ideal grinder for squared timber and more. Designed to work on both sides of the workpiece with three-dimensional adjustment, the Q-Sand guarantees maximum precision and uniformity. It is equipped with grinding discs, flap brushes, and a double disc for more effective material removal, thus improving adhesion for subsequent treatments. The Q-Sand can be installed in a production line or, due to its complete operational autonomy, can also be used independently. It is also ideal for window frames, beams, and custom-made products, and optimizes processing times with automated systems and advanced production control. ----- Price of the above-mentioned machine available upon request! ----- (Technical specifications according to the manufacturer - without guarantee!) All prices quoted are net prices, excluding VAT. The video is from the manufacturer Ecoline and shows a new machine.

Condition: new, Year of construction: 2026, Working width 4500 mm Working height 3000 mm Number of cylinders 6 St. Dimensions (L/W/H) 5500x1400x3550 mm Weight 3000 kg S&S frame press Bavaria 2000 L, built 2026 ----- SHORT TIMED availabe exw warehouse Engelfried, 73447 Oberkochen NEW for the Holz-Handwerk 2026 trade fair in Nuremberg: Now also with semi-automatic positioning of the vertical press cylinders 1, 2, and 3 via enabling switch, including ON/OFF selector switch for beam 2 With automatic pressing cycle + manual control for corner connections tenon+slots and dowel connection/mortised tenon, can be switched using a selector switch on the control cabinet. With basic equipment for optional use of counter profiles if the sash is rebated on the loose part. CE version Basic machine in the strongest frame welded construction, with thick-walled special hollow profiles. Guideways of the pressure beams for the press corners in a low-abrasion machined version. Fast, smooth, manual width adjustment using ball-bearing carriage, fixing in 50 mm hole grid, optional motorized width adjustment with hydraulic clamping (at an additional cost). Height adjustment and pressing using long-stroke cylinders in one work cycle. Right-hand press corners with integrated horizontal cylinders, therefore no vertical positioning of the horizontal pressure Djdjwg Hr Tjpfx Acxoki cylinders is necessary, which avoids cylinder collisions. Lower support can be adjusted in several positions to the most suitable insertion height. 3 KW compact hydraulic system with integrated control block, variable pressure control from 20 - 120 bar, pressure gauge Control via touch button with separate control circuits for the vertical and horizontal press cylinders, mounted on a freely movable control panel. 2 vertical press cylinders, double-acting, stroke adapted to working height, piston diameter 60 mm Pressure force per cylinder max. 2100 kg 2 horizontal press cylinders, double-acting, 80 mm stroke, piston diameter 40 mm Pressure force per cylinder max. 1250 kg Abutment and pressure plate depth 100 mm Control cabinet on the machine base on the left, 400 volts, 50 Hz Machine with ready-to-connect plug 16 A Paint: RAL 7035 light gray with RAL 7016 anthracite gray Working size: length x height = 4,500 mm x 2,750 mm Note: Actual working size: 4,500 x 3,000 mm (length x height) Space required: 5,500 mm x 1,400 mm x 3,550 mm (LengthxWidthxHeight) Article medium pressure bar complete with pressure cylinder, pressure hose and shut-off valve up to 2,750 mm high Note: actual working height: 3,000 mm Article Individual pressure control for medium pressure bar, pressure control range up to max. 100 bar (For pressing cross-bar windows) Article infinitely height-adjustable cross pressure device, complete with pressure cylinder and abutment, throttle and shut-off valve Article Individual pressure control for cross pressure device pressure control range up to max. 100 bar (For pressing cross-bar window) Article Shut-off valve on the 3rd vertical cylinder Article Shut-off valve on the upper horizontal cylinder Article Shut-off valve on the lower horizontal cylinder ...

Condition: used, Number of sanding units 4 St sanding width 190 mm Sanding height max. 4-180 mm weight 4200 kg Hess Expert 4-belt single wood sanding machine machine will be checked by our technicians ----- Ø Grinding at the bottom/top Ø With 2 offset grinding units each (bottom and top) Ø Grinding units (bottom and top) connected in series according to the Dressing principle Ø Pre-sanding with coarse grit (calibrate) Ø Regrinding with fine grit (finish) Ø Central motorized height adjustment of the lower grinding units Ø Central motorized and synchronous height adjustment of the entire upper Grinding and brushing units including the upper transport units Ø Oscillating sanding belt utilization (during the sanding process) Ø Absolute power connection thanks to 5.5 KW motors and large dimensions drive drums Ø Oxide ceramic grinding shoe for - exact surface geometry - no adjustment work - permanent dimensional accuracy - completely maintenance and wear-free Basic structure: Stable, heavy welded construction made of strong-walled rectangular profiles additional, statically calculated reinforcements for optimal Vibration dampening. Staggered grinding units with large dimensions Belt drive drums for slip-free belt running. Two-point suction for direct and flying dust with sealing brushes and integrated sanding belt blow-off Device to increase the service life of the sanding belts. Grinding units in heavy steel plate construction as the basis for vibration-damped, quiet tape running. Absolutely backlash-free guides as ball linear sets hardened and ground shafts. Height adjustment of the grinding units via hardened and ground special linear guides as well as pre-tensioned ones Guide carriage. Permanent precision thanks to dust and dirt protection Ball linear sets and guide carriages. Large-sized pre-grinding rollers as contact rollers. Contact rollers and Sanding shoes in a balanced ratio to the sanding belt grain load. The large drive drums guarantee full transmission the 5.5 kW drive power of the grinding motors on the sanding belt. Therefore Slip-free, stable running and optimal heat dissipation. This makes it the strongest Chip removal possible. Automatic machine stop activation in the event of a belt break. Visual display on the control panel and via flashing lights on the machine. Sanding shoes for finish completely maintenance-free and wear-free made of oxide ceramic with optimal heat dissipation. Grinding belt tension via appropriately sized compression springs. Sanding belt relaxation for belt changing using a pneumatic device sensitive, distortion-free placement of new tapes. Upper grinding unit and brush device centrally motorized Height adjustable with digital display in the control panel for the motorized Grinding thickness adjustment. Brushing and finishing device, for better surface finish, integrated into the basic machine. Two special brush rollers 150 mm Æ arranged one above the other in synchronous function for advance thrust. Separate height adjustment of the brush rollers on precise Carriage guides for post-correction of wear. Additional transport roller for Removal or further transport of the workpiece from the automatic grinding machine with the conveyor belt. Dodpfx Ast Tqy Eecxeki Wooden guide in the inlet area for hard guide and bearings mounted on both sides pressure rollers. Safe transport of profiled workpieces on ca...

Condition: new, Year of construction: 2025, Dimensions (L/W/H) 4150x1200x1650 mm Dksdpfovz Ezwjx Acxoi Weight 450 kg Total power requirement 1,5 kw

Condition: used, Year of construction: 1990, Ideal for carpenter or climber High capacity 1 saw 2 plate-type spreaders 1 spindle diameter 50mm Dksdpfx Acoyka T Dexoi Pneumatic clamping device Sold as is, with no cleaning or overhaul 380V

Condition: good (used), Year of construction: 2012, functionality: fully functional, overall weight: 7,300 kg, total height: 1,750 mm, total length: 10,000 mm, total width: 3,750 mm, working width: 3,800 mm, For sale: Vertongen Penpro Control window production line Year of manufacture: 2012 Condition: Good, working condition Complete industrial solution for the production of windows and exterior joinery with high precision and efficiency. 🔹 Description The Vertongen Penpro Control is engineered for flexible production of window frames without setup time. Thanks to the unique combination of tool spindles, various profiles and dowel joints can be produced in different wood thicknesses and widths. It offers stable and highly accurate positioning of the workpieces. After machining, components automatically return to their starting position, resulting in high repeatability and consistent dimensions—ideal for serial production. The central working position allows operation by a single operator, ensuring an efficient workflow and reduced labor costs. 🔹 Applications - Tenoning - Profiling - Window and exterior joinery - Sliding windows & French doors - Angled windows - Solid cabinet doors - Series production with high precision 🔹 Technical specifications - Brand: Vertongen - Model: Penpro Control - Year of manufacture: 2012 - Industrial, robust design - Suitable for 68 mm and 90 mm profiles Dksdpfeyky Diex Acxsi - Can be operated by one person - High repeatability

Condition: used, Year of construction: 2002, total width: 1,550 mm, total height: 1,500 mm, Empty weight: 1.800 kg Dimensions (LxBxH): 325 x 155 x 150 cm Four-sided moulder SCM Compact 23K Built in 2002 Min/max working height 120mm Min/max working width 230mm Working speed 6/12 m/min Dkedpfjwnhk Tsx Acxei Spindle speed 6000 Rpm Spindle diameter 40mm Min/max tool diameter vertical spindle 100/180mm Input table length 2500mm CNC Program Engines 1st Spindle - Under 5.5kW 2nd/3rd Spindle - Left/Right 11kW 4th Spindle - Up 7,5kW Dimensions 3250x1550x1500mm (LxWxH), Weight 1800kg - Year: 2002 - Documentation available: Yes - CE certificate present: No - Transport dimensions: 3250mm x 1550mm x 1500mm (l x w x h) - Transport weight [kg]: 1800kg Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Year of construction: 2022, condition: used, Number of sanding units 6 st. Sanding height max. 120 mm Dkjdpsynnttsfx Acxji output 12 kw

Condition: good (used), Year of construction: 1994, Window processing line, CNC window manufacturing plant, window angle machine, clamping device, pneumatic clamp -Manufacturer: Gubisch, clamping device from window manufacturing plant type DST H Djdpfxoyibx Aj Acxeki -Stroke: 120 mm -Clamping cylinder: airtec HM-25-120 -Number: 2x clamping device available -Price: per piece -Dimensions: 560/225/H80 mm -Weight: 5 kg/pc.

Condition: good (used), Year of construction: 1994, Window processing line, CNC window manufacturing plant, window angle system, clamping device Dkjdpfoyibvhjx Acxei -Manufacturer: Gubisch, clamping device from window manufacturing plant type DST H -Stroke: 180 mm -Geared motor: SSB type SSB DS-SgFFH008 0.25 kW / 405/57 rpm -Encoder: ferrocontrol SAE-1020 H -Number: 2x clamping device available -Price: per piece -Dimensions: 850/450/H240 mm -Weight: 42 kg/pc.

Condition: good (used), Year of construction: 1994, Window processing line, CNC window manufacturing plant, window angle machine -Manufacturer: Gubisch, Saw unit right left from window manufacturing plant type DST H -Motor: Fimec type H80SB25EF 4 kW / 2800 rpm -Shaft: Ø 30 x 70 mm -Saw blade: Ø 345 mm -Price/Fee: complete -Dimensions each: 470/410/H425 mm Dkjdpfx Aeyibczocxji -Transport dimensions: 970/500/H425 mm -Weight: 87 kg

Condition: used, Number of spindles 3 St. Number of tools 8 St. Spindle diameter 50 mm Dimensions (L/W/H) 4250x1850x2300 mm ! MACHINE FUNCTIONALLY CHECKED AND READY FOR DEMONSTRATION ! !!! Technical description in RUSSIAN, more machine pictures as well as machinevideos - if available - at the end of this description as attached files !!! # 6988 Weinig Univar 6 CNC ..... ..... Technical details summary (please ask for possibly more included equpment) ..... ..... 1st profiling spindle: ..... ..... > spindle rotation direction: clockwise and reverse for rip-off free outside profiling of sashes > position: vertical right > number of tools: 1 pcs. > length of spindle: 120 mm > number of revolutions: 6000 rpm > spindle diameter: 50 mm > tool diameter max.: 232 mm > engine: 11 kW 2nd profiling spindle: ..... ..... > position: vertical right > number of tools: variabel, CNC > length of spindle: 320 mm > spindle stroke vertical: variabel, CNC > number of revolutions: 6000 rpm > spindle diameter: 50 mm > tool diameter max.: 232 mm > engine: 11 kW 3rd profiling spindle: ..... ..... Djdpfxsymf Eks Acxjki > position: vertical right > length of spindle: 160 mm > number of revolutions: 5850 rpm > spindle diameter: 40 mm > tool diameter max.: 210 mm > engine: 3 kW More features: ..... ..... > possible to work online: > monitor control: > Equipment for profiling small sashes: min. 500 mm > Control: PC-Nexus If the technical characteristics of this machines donnot fit with your requirements, please get in contact with us. Our longtime experienced team is looking forward to support you in technical adaptions or in finding a suitable machine for you! Technical details according to manufacturer - without guarantee!

Condition: used, Year of construction: 2000, Storage location: Nattheim Djdpsvwdmwofx Acxjki

Condition: used, Year of construction: 1985, Weight: approx. 3000 kg Dimensions: approx. 3700 x 2000 x 1600 mm Storage location: Nattheim Dkedpfx Acevvi Ttsxei

Condition: used, Year of construction: 2007, from training workshop, public facility, chrome-plated stops and machine table Dedpovwghkofx Acxski used, top condition, hardly used, top equipment Make Weinig Type Unimat 300 Year of manufacture: 2007 Number of spindles 5 Spindle arrangement u-right-li-o-b Motor brakes Planing width approx. mm 20-230 Planing height approx. mm 8-160 Spindle diameter mm 40 Table length approx. mm 2000 Pre-milling cutter Pneumatic pressure of the rollers Protective cover Table lubrication lubricant pump Feed in front of the planer Feed speed continuously variable 5-30 m/min. Profiling D 125 - 200 mm Electrical adjustment of thickness shaft Digital displays complete. incl. profiling Storage location 97447 Gerolzhofen, free loading, unpacked Handed over in the current condition, as inspected, without guarantee or warranty

Condition: used, Tenoning spindle 1 St. Number of milling agregates 4 St. Spindle diameter 50 mm # 2809 Weinig Unicontrol 6 ----- Technical Data Summary (Please inquire about any additional accessories included) Item 1: Cut-off saw ----- > Number of tools: 1 pc. > Spindle speed: 2,800 rpm > Spindle diameter: 40 mm > Maximum tool diameter: 400 mm > Motor power: 3.0 kW > Laser guide light for identifying the saw cut CNC-controlled length stop ----- > Length: 3,600 mm > Electronic length stop including positioned cut-off saw Item 2: Tenoning spindle ----- > Number of tools: 3 (stroke 2 x 100 mm) or 4 (Stroke 3 x 80 mm) > Tool clamping length: 320 mm > Pneumatic vertical spindle stroke: 240 mm for wood thicknesses 68 - 92 mm > Spindle speed: 3000 rpm > Maximum tool swing diameter: 320 mm > Spindle diameter: 50 mm > Maximum tool diameter: 360 mm > Motor power: 11 kW Item 3: 1. Profiling spindle (co-rotation and conventional) ----- > Position: vertical right > Number of tools: 1 pc. > Tool clamping length: 120 mm > Spindle speed: 6000 rpm > Spindle diameter: 50 mm > Maximum tool swing diameter: 232 mm > Motor power: 7.5 kW Item 4: 2. Profiling spindle ----- > Position: Vertical right > Number of tools: 3 (stroke 2 x 100 mm) or 4 (stroke 3 x 80 mm) > Tool clamping length: 320 mm > Pneumatic vertical spindle stroke: 240 mm for wood thicknesses 68 - 92 mm > Spindle speed: 6000 rpm > Spindle diameter: 50 mm > Maximum tool swing diameter: 232 mm > Motor power: 11 kW 2 axially indexed feed rollers opposite the profiling spindle, Dksdpfx Acoxtvgkjxsi for the production of narrow, short parts (e.g., glass-dividing muntins) Munch guide consisting of: Munch support strip from above in the area of ??the vertical right-han d profile milling unit and profiling spindle. Item 5: Horizontal top profile milling unit ----- > Clamping length: 40 mm > Spindle diameter: 40 mm > Motor power: 3.0 kW > Spindle speed: 5,850 rpm > Maximum tool swing diameter: 130 mm > Axial travel: 52 mm, indexed in 2 positions > Radial travel: 125 mm, indexed in 2 positions Item 6: 3rd profiling spindle (fitting spindle) ----- > Position: Vertical right > Tool clamping length: 160 mm > Axial travel: 90 mm, indexed in 3 positions > Radial travel: 100 mm, indexed in 2 positions > Spindle speed: 5,850 rpm > Spindle diameter: 40 mm > Maximum tool swing diameter: 210 mm > Motor power: 3.0 kW Further features ----- > Electric feed height adjustment including mechanical digital display and manual feed bar clamping > Rebating device for tear-out-free rebating > Double part package > Return conveyor for 1-person operation: swivel conveyor > Screen control > Angled window device > Electronic angle display for angled windows > Industrial PC with Windows PC control/NEXUS Extraction nozzle diameter: ----- Crosscut saw 80 mm Tenoning spindle 140 mm Profile spindle 1 140 mm Profile spindle 2 140 mm Grooving device from above 80 mm Hardware spindle 120 mm ----- Price of The above-men...

Condition: good (used), Year of construction: 2011, Weinig Conturex C4500 CNC Window production machine Description; Year of construction: 2011 Working width 25-260mm Working heigth 10-150mm Powergrip clamping table 3.000 mm Dodpfx Acoydkzxjxski Workpiece length 180-4500 mm First processing unit - 20 kW Motor - HSK 63F toolholder - Speed electr. adjustable 0-18.000 t.p.m. (left-right) - Tooldiameter max 330 mm - Sawblade diameter 280 mm - Toolwarehouse 18 positions (100mm distance) Second processing unit - 20 kW Motor - HSK 63F toolholder - Speed electr. adjustable 0-18.000 t.p.m. (left-right) - Tooldiameter max 330 mm - Sawblade diameter 280 mm - Toolwarehouse 18 positions (100mm distance) Powergrip outfeed Tool warehouse 110 positions (87,5 mm distance) Waste conveyorbelt Full description on request Available approx. wk 30/31 - 2026 (Despite our great care all changes, mistakes in technical data, prices and all information is subject to (typing) errors. No guarantee on printed data! Availability subject to prior sales). (Alle Änderungen und Irrtümer in den technischen Daten, Angaben und Preisen vorbehalten! Keine Garantie auf gedruckte Daten!. Verfügbarkeit vorbehaltlich Zwischenverkauf). Prices excl. advertisement cost MachineSeeker / Preise exkl. Inserierungskosten MaschinenSucher Best woodworkingmachines from the Netherlands Holland Die besten holzbearbeitungsmaschinen aus die Niederlande De beste gebruikte machines uit Nederland

Condition: used, Year of construction: 1999, total width: 1,260 mm, total height: 1,750 mm, Empty weight: 1.300 kg Dimensions (LxBxH): 175 x 126 x 175 cm Four-sided planer Griggio G18/4 Year of construction 1999 400 V, 23 kW, 47 Ampere Machine number: MC00029325 Tersa planing heads Min/max working width 25/180mm Min/max working height 7/120mm minimum workpiece length 450mm Feed speed 7 or 14m/min Spindle diameter 40mm Dodpoyff Rkefx Acxjki Input table 2000mm Speed 6000 rpm 4 axles: 1st, bottom: 5.5kW 2nd/3rd, left/right: 7.5kW 4th, top: 7.5kW 3300x1600x1700mm, weight 1300kg - Year: 1999 - Documentation available: Yes - CE marking present: Yes - CE certificate present: No - Serial number: MC00029325 - Deals (actions): er deal - Transport dimensions: 1750mm x 1260mm x 1750mm (l x w x h) - Transport weight [kg]: 1300kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: ready for operation (used), Year of construction: 1988, Window manufacturing machine Dodeyk Haqepfx Acxoki Manufacturer: Okoma Model: UF1 S Year of manufacture: 1988 with tool