Used hydraulic presses double column / Four column presses for sale (310)

Condition: used, Year of construction: 1986, Pressure total: 500 ton Stroke: 1100 mm Iaedpfxeuqdqls Aalep Daylight: 1500 mm Table surface area : 2000 x 1250 mm Slide area: 2000 x 1250 mm Die cushion capacity in table: 160 ton Die cushion stroke: 300 mm Approach speed: 650 mm / sec Required power: 55 kW Weight of machine approx.: 50 ton Standard configuration The press was completely overhauled mechanically, hydraulically and electrically in 2008.

Condition: used, Year of construction: 1996, machine/vehicle number: 14.194, Pressure total: 80 - 800 ton Ram stroke: 1600 mm Free frontal opening L-R: 2850 mm Free lateral opening F-B: 1000 mm Daylight: 1900 mm Table surface area : 2800 x 2000 mm Slide area: 2800 x 2000 mm Die cushion capacity in table: 32 - 320 ton Die cushion stroke: 400 mm Die cushion pad area: 2500 x 1700 mm Approach speed: 400 mm / sec Working speed: 5 -42,7 mm / sec Isdpfeu Saaaox Aaleap Return speed: 420 mm / sec Required power: 246 kW Height over floor approx.: 7785 mm Weight of machine approx.: 100 ton No. of moving bolster: 1 pcs.

Condition: used, Year of construction: 2002, machine/vehicle number: 10857, Pressure total: 315 ton Stroke: 1100 mm Daylight: 2200 mm Table surface area : 2500 x 1000 mm Slide area: 2500 x 1000 mm Die weight at the ram max.: 6000 kg Approach speed: 600 mm / sec Iasdpfx Aevmfzboalep Working speed: 32 - 230 mm / sec Return speed: 600 mm / sec Required power: 158 kW Weight of machine approx.: 44 ton Height over floor approx.: 6175 mm Automation

Condition: used, Year of construction: 1989, Pressure total: 1400 ton Stroke: 950 mm Daylight: 2000 mm Table surface area : 3600 x 2500 mm Slide area: 3600 x 2500 mm Die cushion capacity in table: 400 ton Die cushion stroke: 500 mm Die cushion pad area: 3060 x 1860 mm Approach speed: 400 mm / sec Working speed: 40 / 80 mm / sec Return speed: 400 mm / sec Oil volume: 5000 l Iaodpeuqdi Usfx Aaljp Required power: 450 kW Weight of machine approx.: 240 ton Standard configuration with hydraulic tool clamps on the ram

Condition: used, Year of construction: 2006, machine/vehicle number: 18282, Pressure total: 140 ton Stroke: 800 mm Daylight: 1.004 mm Free frontal opening L-R: 2.060 mm Table surface area : 2.000 x 520 mm Slide area: 2.040 x 520 mm Iasdjuqd Nujpfx Aalsp Working speed: 4 -20 mm / sec Rapid travel: 135 mm / sec Return speed: 120 mm / sec Weight of machine approx.: 14 ton Height over floor approx.: 4.810 mm Oil volume: 700 l

Condition: used, Year of construction: 2006, machine/vehicle number: 18282, Pressure total: 140 ton Stroke: 800 mm Daylight: 1.004 mm Free frontal opening L-R: 2.060 mm Table surface area : 2.000 x 520 mm Slide area: 2.040 x 520 mm Working speed: 4 -20 mm / sec Rapid travel: 135 mm / sec Isdpfxjuqd S Ae Aaleap Return speed: 120 mm / sec Weight of machine approx.: 14 ton Height over floor approx.: 4.810 mm Oil volume: 700 l

Condition: new, stroke lenght (max.): max. 400table height: Fußboden bis Tischplatte Oberkante 850daylight: 600speed: Vorlauf 120 mm , Druck 13 - 4 mm, Rücklauf 170/mm/formance of pump: 65 Lt./min (REXROTH - Axialkolbenpumpe)motor: 15 kw - 1500d / minmessurements (LxWxH): 2.100 x 2.400 x 4.300weight approx.: 11.000 Capacity: 1500kN. (150 ton - at 245 BAR) Operating selection: Via key switch Manual / set-up via two-hand operation without light sensor fuse on front side (rear side always active) Automatic via two-hand operation at full speed (with active light sensor fuse) Main cylinder: Ø 270mm. Auxiliary cylinder: 2 pcs. Ø 70 x 50mm. Motor: 15kw. - 1500d/min. (IE-3) Pump: 45cc. - 65Lt./min.   REXROTH - axial piston pump Speed: flow 120mm. - Pressure: 13 - 4mm. - Return 170mm./sec. Clearance: 1300mm. Iedpompfwdofx Aaloap Table top: 1200 x 800 x 90mm. - with T - grooves ram plate: 1200 x 800 x 600mm. - with T - grooves & ribbing Installation height: 600mm. (max. distance between table & ram plate) Stroke length: max. 400mm. Table height: 850mm. (Floor to table top upper edge) ----- Hydraulics: (Hydraulic accessories on top of the press) Kontrol Block & Valves (REXROTH Proportional Valves) Prefill valve (NG.125) 8 way guide Hydraulic ram safety device Mechanical ram safety device for TDC position Pressure adjustment via PLC. Speed adjustment via PLC. Pressure stop valve for 600 sec. Air cooler Automatic lubrication for guides Auxiliary motor Auxiliary pump Control system: Main control box (mounted on the side of the press frame) Pivoting control panel SIEMENS S7 - 1200   KTP. 9 SIEMENS screen (language selection DE.- ENG.) Safety PLC. (SICK) Light sensor for front & back of work area (SICK 750 + 150mm.) Soft starter Two hand operation (Movable) SECOMEA Ethernet connection Ruler for setting the stroke length (450mm. - NOVOTECHNIK 16BIT) Workspace lighting (2-fold IP-66)   8 free ON & OFF outputs on the PLC. for external connections ----- Protective railing around the hydraulics Lateral ladder ----- Documentation: Operating manual DEUTSCH(1 fold paper & 1 fold USB.) Hydraulics & control diagrams Parts lists CE. Certificate Standard :EN.16092/1/3 ----- Total dimensions: approx. 2400 x 2100 x 4100mm Total weight: approx. 11.000kg. Painting: frame RAL 7035 light grey, railing & hydraulics RAL 7016 anthracite grey. -----

Condition: good (used), Year of construction: 1992, functionality: fully functional, machine/vehicle number: 50 /92-NG 600/15 kW/32Liter, pressing force: 130 t, operating speed: 80 mm/s, overall weight: 3,500 kg, Hydraulic straightening press Manufacturer: G + K Year of manufacture: 1992 Max. pressing force: 130 t Table size bottom: 800 x 500 mm with T-slots Table size top: 800 x 500 mm with T-slots Fitting dimension: 1000 mm System pressure: 250 bar Electric motor: 15 kW Weight: 3400 kg Operating voltage: 380 V AC, 24 V DC Iaedexr Rnaopfx Aalsp Control system renewed 5 years ago 2 tables at the bottom, 800 x 500 mm

Condition: like new (used), functionality: fully functional, machine/vehicle number: FDL-150-100E/NC, total length: 1,200 mm, pressing force: 150 t, table width: 800 mm, working height: 600 mm, clearance between the columns: 1,250 mm, Equipment: documentation/manual, safety light barrier, DOUBLE-COLUMN HYDRAULIC PRESS WITH TWO SIDE CYLINDERS FOR PRE-PRESSING AND PRESSING OF ROTORS AND STATORS, AND A CENTRAL CYLINDER FOR ROTOR SHAFT EXTRACTION, AS WELL AS FOR SHAFT EXTRACTION IN CASE OF REPAIR It features an extendable table for stacking and handling rtors and stators. It meets and satisfies all essential safety and health requirements according to CE regulations. STRUCTURE AND TABLES • Consists of a rigid fixed bench welded structure made exclusively from S355JR steel. • Stabilized and machined at the end of the welding process to ensure perfect parallelism and precision. • Calculated and designed using finite element software. • Mechanically movable grooved table measuring 1200 x 800 mm with a stroke of 1,200 mm, equipped with a worm gear reducer and a 0.5 HP electric motor with brake. • Central drill on the table with a diameter of 250 mm and a maximum depth of 550 mm. • Useful lifting capacity of the table for moving 4 tons. • Movement speed of 30 mm/sec. • Front interior width of 1250 mm (space between columns). • Working height of 600 mm. Ijdewpg Awjpfx Aaljap MAIN CYLINDERS: 150 TN • Two 75-ton hydraulic cylinders (150 tons total), with a stroke of 1200 mm connected by a plate with a central hole of 250 mm in diameter. • Maximum useful height of the cylinder plate: 1,440 mm. • Minimum useful height of the cylinder plate: 200 mm. ABSTRACTION CYLINDER • One 100-ton central cylinder with a stroke of 1200 mm. • Designed to accommodate an abstraction clamp, end of the rod threaded to M 35.150 x 40 mm length. • Maximum useful height of the abstraction cylinder: 1600 mm from the root of the rod thread. • Minimum useful height of the abstraction cylinder: 400 mm from the root of the rod thread. HYDRAULIC GROUP • Two-speed hydraulic group with 5.5 HP power “Siemens Motor”, with automatic disconnection of high speed and independent speeds. Maximum pressure: 250 bar. • Pressure regulation system using proportional valves. • Air-oil cooler. • Temperature sensor. • Hydraulic group located on the right side. ELECTRICAL INSTALLATION AND SAFETY • Equipped with a SIEMENS mod. SIMATIC S7 1200 safety PLC and a 12” HMI touchscreen mod. MTP with 99 memory slots allowing adjustment of pre-pressing power, pressing, calendering, and stroke of the pressing and extraction cylinders, as well as the holding times during processes. • Electrical and hydraulic maneuvers are redundant and self-controlled. They include an additional safety block and self-control devices for operation and safety. Includes verification and certification of correct operation and safety distance for photoelectric cells. • The electrical panel includes a selector for choosing the type of work in manual, semi-automatic, or automatic position and a selector for high-speed or low-speed operation. • Operation is performed via a two-hand low-voltage electrical pushbutton. • All installed electrical materials are Siemens, including relays, contactors, main motor, etc. • Ready for Industry 4.0. • To ensure safety, it includes category IV photoelectric barriers located in the front work area, two fixed side guards, and a practicable rear guard with a magnetic disconnection detector.

Condition: used, Year of construction: 2021, functionality: fully functional, total height: 7,000 mm, total width: 4,750 mm, total length: 6,000 mm, pressing force: 1,000 t, reverse speed: 60 mm/s, The MV-1000E/NC-SINCRO hydraulic press is custom-designed for the adjustment of progressive dies. It features a tilting upper table and a movable lower table made of C45E steel, machined with DIN-650 T-slots to ensure minimal friction in the vertical movement of the upper table. This is achieved through the installation of maintenance-free bimetallic bushings and perfect parallelism ensured by four high-mechanical-resistance cylindrical columns of 300 mm in diameter, chrome-plated and rectified. STRUCTURE AND TABLES • Features a structure made from oxy-cut steel divided into three electro-welded monoblocks, exclusively manufactured from S355JR steel. • Stabilized and machined at the end of the welding process to ensure perfect parallelism and precision. • Calculated and designed with finite element software. • Cylindrical columns with a diameter of 300 mm, high mechanical resistance, rectified, and chrome-plated to maintain a low friction and wear coefficient. • Upper table with T-slots and anti-fall safety system. • Useful table surface: 4,750 x 2,250 mm. • Structure designed to support 600 TN of concentrated force on 1/3 of its surface. • Lower table designed to support up to 50 TN in displacement, supported by bronze guides with graphite load and mechanical positioning centers for precise table positioning. CYLINDER AND HYDRAULIC GROUP • 6 single-acting cylinders with lapped sleeves, chrome-plated pistons, and anti-wear guides. • Four 50 TN hydraulic compensators located at the ends of the lower table. • 800-liter hydraulic group with a silent Denison pump, automatic disconnection of the fast approach pre-filling speed, and equipped with a decompression system in working speed. • Proportional pressure system and optical gauges for displacement control on the upper table, with a synchro-electronic system for compensating off-center or unbalanced forces. • Hydraulic group cooling system with an independent air-oil radiator unit. • All M series hydraulic presses include a lateral pressure switch to adjust the most suitable pressure setting for each type of work. Iaodpewpgwnjfx Aaljp • Glycerin manometer with tonnage reading. ELECTRICAL INSTALLATION AND SAFETY • Includes a SIEMENS safety PLC model SIMATIC S7 1200 and a 12” touchscreen. Allows programming of semi-automatic and automatic operating modes, power, travel, and upper table dwell time. Capable of storing 300 recipes, with each recipe able to program all the above values. • Low voltage operation via two-hand pushbutton. • Anti-fall safety system with hydraulic safety jaws. • Level IV photoelectric barriers installed at the front and rear. • Lateral protections with opening and safety microswitches. TECHNICAL SPECIFICATIONS Power tn 125 - 1000 Opening Force tn 100 Powered Speeds 1 Engine Power kW 75 Fast Pre-Fill Speed mm/s 100 Variable Working Speed mm/s 12-4 Return Speed mm/s 60 Guide Diameter mm 300 Maximum Pressure Bar 290 Useful Table Area mm 4.750 x 2.200 Lower Table Displacement mm 2.200 Vertical Travel of Upper Table mm 800 Between Columns mm 5.000 x 1.490 Total Front mm 6.000 Total Side mm 4.750 Total Height mm 7.000 Weight kg 150.000

Condition: new, functionality: fully functional, machine/vehicle number: MV-250E/NC, pressing force: 250 t, table width: 2,500 mm, table length: 1,150 mm, Equipment: documentation/manual, safety light barrier, HYDRAULIC FOUR-COLUMN PRESS FOR DEEP DRAWING APPLICATIONS TECHNICAL DATA Press force / Main cylinder 250 t Blankholder force 50 t Motor power 11 kW Ram stroke 500 mm Approach speed 80 mm/s Working speed 7 mm/s Return speed 105 mm/s Column diameter 150 mm Maximum pressure 260 bar Usable table area 2,500 x 1,150 mm Column clearance 2,500 x 700 mm Maximum open height 1,000 mm Blankholder (cushion) size 950 x 750 mm Working height 1,100 mm Overall height 3,650 mm Weight 15,000 kg The hydraulic four-column press MV-250E/NC belongs to the M/NC series and is specially designed for high precision and capacity, particularly in deep drawing operations. Outfitted with upper and lower tables made from C45E steel, featuring DIN-650 T-slots to ensure minimal friction during vertical movement of the upper table. This is facilitated by maintenance-free bi-metal bushings and perfect parallelism by means of four chrome-plated and precision-ground cylindrical columns. The press features an optimized hydraulic system operating at pressures below 290 bar, ensuring long service life and reliable performance. It complies with all essential safety and health requirements in accordance with CE regulations. STRUCTURE AND TABLES • Consists of three fully welded blocks, manufactured exclusively from S355JR steel. • Stabilized and machined after welding to ensure perfect parallelism and precision. • Designed and calculated using finite element analysis software. • The lower table is equipped with a 50-ton hydraulic cushion, usable area 950 x 750 mm, and three front supports for tooling outside the press. • Integrated SIEMENS KTP-400 NC for controlling ram stroke, speed changes, and cushion control. • Includes a SIEMENS S7 PLC, permitting storage and programming of up to 99 settings. CYLINDER AND HYDRAULIC UNIT • Single-acting cylinder with honed sleeve, chrome-plated piston, and wear-resistant guides. • Complete hydraulic unit installed on the top of the press. • Hydraulic unit comprises a low-noise Denison hydraulic pump and an air-oil cooler. • Includes: - Decompression system - Solenoid operated pressure valves - Pre-fill valves - Communication valve - Check valve Iasdpfx Aaswkucholsp - Pressure relief valve - Safety catch valve ELECTRICAL INSTALLATION AND SAFETY • Features a SIEMENS SIMATIC S7 1200 safety PLC and a 4-inch KTP-400 touchscreen on the control panel. Enables programming of semi-automatic and automatic modes, power, stroke, and dwell time. Offers storage for up to 99 recipes; each recipe is fully programmable for the above parameters. • The electrical control panel features a selector switch for mode selection: manual “setup” or automatic “production” cycle. • Machine operation via electric low-voltage foot pedals. • Safety features include category IV light curtains in the front working area, two fixed side guards, and a rear safety guard with a magnetic interlock detector.

Condition: used, Year of construction: 2020, functionality: unexamined, total height: 6,400 mm, total width: 4,500 mm, total length: 3,800 mm, operating speed: 110 mm/s, reverse speed: 180 mm/s, distance table to ram: 1,500 mm, We are offering here a new build of the machine shown. The machine was put into operation in 2020 and can be inspected by the customer. Technical data: Press force T 800 Opening force T 80 Motor power KW 55/75 + 55/75 Piston stroke 1000mm Rapid pre-fill speed mm/s 110 Iaodpfxjwlrv Uo Aalsp Working speed mm/s 6 Return speed mm/s 180 Guide diameter mm 250 Max pressure Bar 250 Useful table area mm 3,500 x 2,000 Lower table displacement mm 2000 Between columns mm 2,000 Open height mm 1500 Total front mm 3800 Total side mm 4500 Total height mm 6400 Weight kg 134,600 The MV-800E/NC-SINCRO press was specially developed for the adjustment and testing of molds, dies, and stamps. The 4 columns with 250 mm diameter made of C45E steel were specially manufactured for high stress. It features an optimized hydraulic system with a pressure of up to 250 bar, ensuring long service life and reliability. It meets all essential safety and health requirements according to CE regulations. STRUCTURE AND TABLE • A structure that withstands 600 T concentrated force on 1/3 of its surface. • Lower table with T-slots. • Upper table with T-slots. • Usable table surface: 3,000 x 2,000 mm. CYLINDER AND HYDRAULIC UNIT • Two double-acting hydraulic cylinders with 400 T each. • Single-stage hydraulic unit with automatic shutoff of pre-fill speed and independent operation, equipped with a decompression system and proportional pressure pre-fill valves. Equipped with digital potentiometers on the upper table for displacement control and an electronic synchronization system to compensate for off-center or unbalanced forces. • The press is equipped with a side pressure switch to regulate the most suitable pressure setting for each specific task. • Glycerin manometer with tonnage display. ELECTRICAL INSTALLATION AND SAFETY • Electrical installation for operation with 1 or 2 speeds of the main cylinder feed. • The press has a manual cycle and an automatic cycle (activated via a test button selector): • The manual cycle allows the execution of all movements (step by step) of the press at slow speed. • The automatic cycle allows the press to perform a complete production cycle. • Electrical safety system for the upper table fall protection system. • Lower table with hydraulic removal and physical stops. • The machine features a control panel with a touchscreen display for entering operating and calibration data. • 2 optical barriers of 1,000 mm with safety level IV installed at the front and rear. • Electrical components from Siemens are manufactured according to applicable CE regulations and laws in protection class IP55. • Electrical and hydraulic functions are redundant and self-controlled. Includes an additional safety block and self-monitoring devices for operation and safety. Includes inspection and certification of correct operation and safety distance for light barriers. • Safety is ensured by a laser and area protection with light barriers of level IV.

Condition: used, Year of construction: 2024, functionality: fully functional, total height: 2,675 mm, table height: 900 mm, total width: 1,075 mm, total length: 1,525 mm, pressing force: 100 t, table width: 700 mm, table length: 500 mm, overall weight: 2,540 kg, reverse speed: 60 mm/s, distance between side stands: 800 mm, stroke length: 250 mm, Equipment: safety light barrier, RIGID FRAME HYDRAULIC PRESSES Iaodpfxewlgkms Aalop We have engineered the motorized rigid frame hydraulic presses of the R/NC series in six different capacities ranging from 80 to 500 tons. Specially designed for stamping, die-cutting, and drawing operations. The latest generation R series hydraulic presses have evolved into highly versatile machines, including the capability to integrate seamlessly into automatic production lines. They operate at a hydraulic pressure below 320 BAR to ensure maximum durability of the entire hydraulic system. The R/NC series drawing and stamping presses feature an electro-welded frame made exclusively from S355JR steel, stabilized and precision-machined after welding for perfect parallelism and accuracy. The frame design and strength are optimized using finite element analysis software, ensuring our high standards of precision and quality are always maintained. Both the upper and lower tables are made from precision-machined C45E steel and feature DIN-650 T-slots. The upper table maintains perfect parallelism by means of four lateral cylindrical guides with maintenance-free, anti-friction bimetallic bushings. The double-acting cylinder features a lapped barrel, a chrome-plated piston, and maintenance-free wear guides. The hydraulic unit is motorized, offering two speeds with automatic disengagement of the rapid speed, and includes a cylinder decompression valve. Standard features include a SIEMENS SIMATIC S7 1200 safety PLC and a 4” MTP-400 touchscreen positioned above the electric foot pedal control. This setup allows for programming of semi-automatic and automatic operating modes, power, stroke, and dwell time of the upper cylinder. Up to 99 recipes can be stored, with full parameter settings for each recipe. The electrical control panel includes a selector switch for manual/automatic operation, and a key switch for maintenance tasks. All electric and hydraulic controls are redundant and self-monitored, with an additional safety block and safety self-monitoring features. The machine includes verification and certification of correct operation, as well as the safety distance of the light curtains. Safety features include type 4 PLe photoelectric light curtains at the front working area, two fixed side guards, and a rear access guard equipped with a magnetic disconnect sensor, polycarbonate windows, and LED interior lighting. Installation of a hydraulic cushion or ejector is supported. Compliant with all essential CE safety and health requirements. Supplied with an instruction manual. Technical Specifications: - Force: 100 t - Motor power: 13 kW - Working speed: 3–9 mm/s - Approach speed: 40 mm/s - Return speed: 60 mm/s - Maximum pressure: 319 bar (up to 320 bar) - Ram stroke: 250 mm - Guide diameter: 50 mm - Lower table: 700×500 mm - Upper table: 600×450 mm - Max. vertical opening: 500 mm - Front opening: 800 mm - Working height: 900 mm - Overall front width: 1,525 mm - Overall length: 1,075 mm - Overall height: 2,675 mm - Weight: 2,540 kg

Condition: like new (used), functionality: fully functional, machine/vehicle number: MV-300E/NC, total height: 3,500 mm, total width: 1,800 mm, total length: 2,300 mm, pressing force: 300 t, table width: 1,250 mm, table length: 1,250 mm, overall weight: 18,000 kg, pressure: 320 bar, Equipment: documentation/manual, safety light barrier, The MV-300E/NC four-column hydraulic press belongs to the M/NC series and is custom-designed to achieve greater precision and capacity, specifically manufactured for deep drawing, punching, and deburring tasks. Power tn 300 Motor Power kW 18 Piston Stroke mm 750 Approach Speed mm/s 110 Variable Working Speed mm/s 5-15 Return Speed mm/s 130 Guide Diameter mm 150 Maximum Pressure Bar 320 Table Usable Area mm 1.250 x 1.250 Between Columns mm 1.250 x 940 Vertical Clearance mm 1.000 Total Frontal mm 2.300 Total Lateral mm 1.800 Total Height mm 3.500 Weight kg 18.000 STRUCTURE AND TABLES Consists of three electrowelded blocks made exclusively of S355JR steel. Stabilized and machined at the end of the welding process to ensure perfect parallelism and precision. Calculated and designed using finite element software. The bottom table has a 50 Tn hydraulic cushion with a useful surface of 950 x 750 mm and three front consoles to support the die outside the press.Incorporates a SIEMENS KP-700 COMFORT NC for the regulation of the top table stroke, speed changes, and cushion regulation. CYLINDER AND HYDRAULIC GROUP 2 single-acting cylinders with lapped sleeves, chromed pistons, and maintenance-free anti-wear guides. 2 auxiliary double-acting cylinders for fast approach and return speeds. Variable speed motorized hydraulic group. Includes cylinder decompression valve. Silent hydraulic pump. All hydraulic presses of the M series include a pressure switch located on the side, allowing the most suitable pressure setting for each type of work to be regulated. Glycerin manometer with reading in tons. Isdpowphhnjfx Aaloap ELECTRICAL INSTALLATION AND SAFETY Incorporates a Siemens SIMATIC S7 1200 safety PLC and a 7” KTP-700 COMFORT touch screen located on the electrical panel. Allows programming of semi-automatic and automatic modes, power, stroke, and dwell time of the top cylinder and cushion. It has a storage capacity of 300 recipes, each recipe can program all the above values. Prepared for Industry 4.0. The electrical panel includes a selector that allows choosing the type of work to be performed in manual, semi-automatic, or automatic mode and a selector to choose operation in fast or slow speed. Electrical and hydraulic maneuvers are redundant and self-controlled. They incorporate an additional safety block and self-control devices for maneuvering and safety. Includes verification and certification of correct operation and safety distance for photocells. Operation is carried out by low voltage electric pedal. For safety, they incorporate category IV photoelectric barriers located in the front working area, two fixed side guards, and a practicable guard with a magnetic disconnection detector located at the rear.

Condition: like new (used), functionality: fully functional, machine/vehicle number: MV-600E/NC, pressing force: 600 t, table width: 990 mm, table length: 890 mm, operating speed: 5 mm/s, overall weight: 23,000 kg, reverse speed: 18 mm/s, Equipment: documentation/manual, safety light barrier, The MV-600E/NC four-column hydraulic press belongs to the M/NC series and is custom-designed to achieve greater precision and capacity, specifically manufactured for stamping, deep drawing, punching, and deburring tasks. Power tn 600 Motor Power 40 HP a 440 Vca / 60hz Working Speed mm/s 5 Approach Speed mm/s 15 Return Speed mm/s 18 Piston Stroke mm 1.015 mm - (40”) Guide Diameter mm 200 Table Usable Area mm 990 x 890 x 130 (39” x 35” x 5”) Between Columns mm 990 x 370 Vertical Clearance mm 1.625 - (64”) Working Height mm 990 - (39”) Lower Hydraulic Knockout Tn 80 Lower Knockout Stroke mm 406.4 - (16”) Upper Hydraulic Knockout Tn 80 Upper Knockout Stroke mm 406.4 - (16”) Total Frontal mm 1.850 Total Lateral mm 1.700 Total Height mm 4.500 Weight Kg. 23.000 Kg. approx. Equipped with a top and bottom table made of C45E steel, machined with DIN-650 slots, and a removable upper counter-table of 990 x 890 x 130 mm for die holders with “T” slots. We ensure minimal friction in the vertical movement of the top table through the installation of maintenance-free bimetallic bushings, with perfect parallelism achieved by four chromed and ground cylindrical columns. It uses an optimized hydraulic system with a pressure of 320 Bar, ensuring prolonged durability and reliability in its performance. It meets and satisfies all essential safety and health requirements according to CE regulations. Isdpfx Aaowpggioloap STRUCTURE AND TABLES • Consists of three electrowelded blocks made exclusively of S355JR steel. • Stabilized and machined at the end of the welding process to ensure perfect parallelism and precision. • Calculated and designed using finite element software. • Incorporates a SIEMENS SIMATIC S7 1200 PLC and a 7” HMI KTP-700 touch panel. This allows programming of the power, cylinder stroke, and speeds, with a storage capacity of 300 memories for different work cycles. CYLINDER AND HYDRAULIC GROUP • Double-acting cylinder with lapped sleeve, chromed piston, and maintenance-free anti-wear guides. • Motorized hydraulic group with two speeds and automatic disconnection of fast speed. High-pressure pump and 10-micron return filter. Includes cylinder decompression valve, directional valve, and safety valve. A pressure switch located on the side allows the most appropriate pressure setting for each type of work. • Glycerin manometer with reading in tons. ELECTRICAL INSTALLATION AND SAFETY • The electrical panel incorporates a selector to choose manual, semi-automatic, or automatic operation modes, and another selector for fast or slow speed operation. • Equipped with a PLC to internally assist with maneuvers and decompression time. • Operation is carried out using a low-voltage electric two-hand button panel. • Electrical and hydraulic maneuvers are redundant and self-controlled, incorporating an additional safety block and self-control devices for maneuvering and safety. Includes verification and certification of proper operation and safety distance for photocells. • For safety, category IV photoelectric barriers are incorporated in the front work area, two fixed side protections, and a movable protection with a magnetic disconnection detector at the rear. • Machine equipped with an IXON system for online communication in case of faults or reprogramming. • Ladder with upper walkway for repair access (scaffold).

Condition: used, Year of construction: 2014, The portal hydraulic press is designed for bending or straightening and finished welded elements as well as for dismantling mining and other machine assemblies. It is used in mechanical, production, repair plants, etc. Manufacturer: PATENTUS S.A. Type: PAT 300-2/250-2 Year of production: 2017 Technical parameters: Dimensions: width: 4200x3140 mm, height: 3600 mm Weight: 25000 kg Table surface: 4200 mm x 2140 mm Diameter of the cylinders of the gate 1: 2 x 300 mm Diameter of the cylinders of the gate 2: 2 x 250 mm Pressure of the cylinders of the gate 1: 2 x 1768 kN Iaedpshktq Aefx Aaljp Pressure of the cylinders of the gate 2: 2 x 1228 kN Clearance max. 1240 mm Working cylinder stroke: 600-660 mm Gate travel: 1420 mm Equipment: - two gates - table - working cylinders x 4 - gate travel cylinder - working cylinder travel cylinder - power unit with pump T-100/30 (2006 with renovation in 2011) Technical condition: used, for inspection

Condition: used, Bending capacity: Ø45 mm Bending angle: 0 - 180° Revolver-adjustment: 8-fold adjustable angles Mandrellength: 4000 mm Sets of bendingdies: 1x Ø 16 mm 2x Ø 17 mm 3x Ø 20 mm Iodpfx Ajq Nipyoaloap 2x Ø 27 mm 1x Ø 28 mm 2x Ø 30 mm Featured with: - 4 Mandrels - Mandrel retraction unit Country of origin: Germany Motor power: 3 kW Machine LxWxH: 400 x 100 x 120 cm Machine weight: 1500 kg

Condition: good (used), Year of construction: 1973, pressing force: 315 t, table width: 1,500 mm, table length: 2,500 mm, Hydraulic 4-column press, manufacturer FIBRO, year of manufacture 1973, pressing force 315 t. Iedpfjx Nhakjx Aaleap Dimensions approx. 3.0 m × 1.6 m × 4.5 m. Table size: 2.5 m × 1.5 m. Separate hydraulic unit and control panel. Maximum working area 883 mm (ram fully retracted). Powered, can be inspected on site. All information has been provided to the best of our knowledge and belief. Subject to change, errors, and prior sale.

Condition: used, Year of construction: 2018, functionality: fully functional, total height: 6,000 mm, total width: 3,500 mm, total length: 4,500 mm, pressing force: 1,000 t, table width: 2,300 mm, table length: 3,000 mm, operating speed: 10 mm/s, overall weight: 78,000 kg, reverse speed: 150 mm/s, working height: 1,300 mm, stroke length: 800 mm, working range: 1,300 mm, pressing speed: 10 mm/s, Hydraulic press 1000t Iaodpfxoyilh Is Aalop - in very good condition, used for stamping first series parts from progressive tools

Year of construction: 2001, condition: excellent (used), Used hydraulic press SACK & KIESSELBACH TRP 200. The originally automatic transfer press was converted to manual in 2012, but can be converted again as an automatic press. The press is still set up and under power and is in very good condition. Pressing capacity in t: 200 Quantity of oil in l: 1100 Stroke in mm: 300 Table size (lxb) in mm: 600 x 600 Daylight in mm: 1000 Upper ejector stroke in mm: 25 Isdpfxshfwqzo Aaljap Upper ejector force in t: 10 Total weight in kg: 12000 Operating pressure in bar: 6 Approach speed in mm/sec: 375 Working speed in mm/sec.: 18 - 40

Condition: new, New hydraulic high speed press from min. 300t up to max. 2500t. We offer new mechanical and hydraulic presses for various applications, individually tailored to your needs. Give us your requirements and we will make an attractive offer with installation and service. ISGEC has delivered to more than 26 countries in recent years, including Thailand, Indonesia, Vietnam, USA, Germany, Spain, France, Brazil, Hungary, Mexico, Bangladesh and over 200 presses to 40 Japanese customers. We are proud to be official sales partner since 2020 and look forward to hearing from you. Iaedsf Rt Irspfx Aaljp

Condition: repair required (used), Year of construction: 1980, functionality: limited functionality, For sale is a Hans Schön hydraulic press with 650 kN capacity. The machine was last in operation about 8 years ago. At that time, it had an issue with a hydraulic pipe (possibly a hydraulic oil leak or a leaking fitting). This was not repaired since the press was no longer needed. Otherwise, the machine had been running flawlessly up to that point. The press does not have UVV certification! Iodpfxsx Ehmyo Aaleap

Condition: repair required (used), Year of construction: 1972, functionality: limited functionality, machine/vehicle number: 611, pressing force: 100 t, For sale is a Hans Schön hydraulic press with 100 ton capacity. It was last used approximately 7 years ago. At that time, the machine had an issue with a hydraulic valve, which was not repaired since the press was no longer needed. Otherwise, the machine ran flawlessly until then. The press does not have UVV (accident prevention certification)! Iodpfx Aox Ehlcsaljap

Condition: excellent (used), Year of construction: 2008, X,Y travel: 14.6" x 10.6" U,V,Z travel: 3.9" x 3.9" x 10.2" Iajdjwqq Rhopfx Aalep Max. workpiece size: 29.5" x 21.7" x 10.2" Max. workpiece weight: 880 LB Max. X, Y rapid traverse: 31.5 in/min Drive system: AC servo motor/linear motor Wire diameter: 0.004" – 0.012" Max. wire feed: 11.8 in/s Wire tension: 0.44 – 5.52 lb Taper angle: ±21°/4.33 in (DA+DB=0.6 in) Layout (W x D x H): 90.6" x 89.2" x 80.6"

Condition: used, pressure 200 t distance between columns 1600 mm max. ram stroke 600 mm dayligth 900 mm table width 1600 mm table depth 1300 mm table height 1060 mm ram surface 1600 x 1300 mm T-slots Din 650 / 22H12 rapid traverse 400 mm/s return speed 325 mm/s pressing speed 42 mm/s bei 40% mm/sec pressing speed 20 mm/s bei 100% mm/sec die-cushion pressure 800 kN Iajdpfx Aaeg S R Twsljp die cushion stroke 150 mm speed of die cushion auf 68/ ab 225 mm/s