Single shaft shredder

VECOPLAN VAZ2000MNF (VAZ220/200KNF)

Condition: good (used), Year of construction: 1994, 2-sided planing machine, top and bottom Constant table (always the same feed height) Max. planing width: 600 mm Max. planing height: 280 mm Gedjhuthyspfx Aciskb Planer shafts with strip knives Ready for immediate use.

Condition: new, Funnel opening: 2,500 x 2,000 mm Rotors: 2 units Gkedpfobq St Hsx Acisb Rotor diameter: 580 mm each Rotor design: 5 and 6 cutting teeth Drive: 2 x 90 kW with planetary gearboxes Hydraulic locking system for sieve flaps to remove disruptive materials Weight: approx. 18,500 kg

Year of construction: 2008, condition: ready for operation (used), A large-format single-shaft shredder Vecoplan is available. Rotor diameter: 370mm, effective rotor length: 1300mm, speed: 120rpm, knife rows: 37, knife dimensions X/Y: 40mm/40mm, feed opening X/Y: 1400mm/1300mm, hopper volume: approx. 3m³. Machine dimensions X/Y/Z: 3200mm/2400mm/1500mm, weight: approx. 5500kg. An on-site inspection is possible. Gksdpoyddyzjfx Acijb

Condition: new, Year of construction: 2016, 1 unit of a completely overhauled, unused industrial bevel-helical gearbox from ASUG. TGL 21815. All gearbox parts have been replaced, with the exception of the housing!!! Clutch: 800 mm (only one half available) Maximum torque: 27,829 Nm Gear ratio: i = 1:80 Maximum power: 51 kW Oil capacity: 170 kg Speed: n1 = 1400 Speed: n2 = 17.5 Weight: 1450 kg Shaft diameter d1: 65 mm Shaft diameter d2: 160 mm Shaft height h1: 500 mm Overall height h2: 925 mm Length of base: 1170 mm Gkjdpfxogwlrds Acijb !! The gearbox does not have an oil cooler !!

Condition: used, Year of construction: 2007, spindle diameter: 45 mm, number of spindles: 6, No. 3176 Automatic planer and moulder WEINIG Hydromat 1000 Used, year of construction 2007, machine already dismantled 6 spindles: bottom-right-left-top-top-bottom Electronic feed 6 - 60 m/min Working width 80 - 150 mm Working height 23 - 65 mm Finished slat widths 4 - 15 mm Max. number of slats 16 pieces Slat lengths 400 - 4000 mm 1st spindle horizontal at the bottom Brake motor 11 kW, 6000 rpm Spindle diameter 45 mm Tool flight circle 125 - 180 mm 2nd spindle vertical right Brake motor 7.5 kW, 6000 rpm Diameter 45 mm Tool flight circle 112 - 250 mm Max. Moulding depth 35 mm Axial adjustment travel 80 mm 3. spindle vertical left 7.5 kW, 6000 rpm Diameter 45 mm Tool flight circle 112 - 250 mm Max. Moulding depth 35 mm Axial adjustment travel 80 mm Pressure shoe in front of the spindle, swiveling away, pneumatic roller contact pressure 4. spindle horizontal top 15 kW, 6000 rpm, diameter 45 mm Tool flight circle 112 - 250 mm Max. Moulding depth 35 mm Axial adjustment path 45 mm Split pressure shoe in front of upper spindle, adjustable and swiveling away, pneumatic 5. horizontal top spindle as saw spindle Brake motor 37 kW, 5000 rpm Diameter 45 mm Axial adjustment travel reduced to 25 mm Tool flight circle 112 - 250 mm Max. Sawing depth 35 mm Axial adjustment path 45 mm Split pressure shoe in front of upper spindle, adjustable and swiveling away, pneumatic 6. horizontal spindle at the bottom as saw spindle Brake motor 30 kW, 5000 rpm Axial adjustment travel reduced to 25 mm Diameter 45 mm Tool flight circle 112 - 250 mm Max. Sawing depth 35 mm Axial adjustment path 45 mm All moulder spindles with high-performance bearings Electronic feed 7.5 kW Adjustment travel of the feed rollers compared to the left-hand spindle, axial 35 mm Shorter roller distance compared to the right-hand spindles Running meter counter, electric, with 2 counters Short infeed table (1.2 m) with 2 driven rollers above the table Gkjdpfju Agh Sox Acieb 1 driven, toothed roller in the table, lateral pressure roller Automatic waxilite pump / lubricant pump Machine with 4-roller extension, pendulum shafts extended to 200 mm 2 driven, toothed rollers in the outfeed table 2 driven, toothed rollers in the machine table Pressure beam before and after upper spindle with mechanical digital display DigiSet (digital double display) for left and top spindles Electrical height adjustment of the upper spindles and the feed Sale on behalf of customer, ex location near 39100 Bolzano (Italy), without dismantling, without transport and assembly Dismantling, loading, and transport by us optionally available Subject to errors in the description and price To avoid any misunderstandings, an on-site inspection is possible and recommended by appointment Sold as is Technical specifications, condition description, year of construction and scope of delivery according to the manufacturer’s brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: “sold as seen” Photos and videos serve as examples and do not represent the actual scope of delivery Terms of payment: Prices plus VAT, payment before collection or shipping Terms of delivery: Ex location

Condition: new, - Motor power 7.5 kW - Cutting force 20 tons Cutting channel designed for: - max. roll length 1100 mm - max. roll diameter 900 mm - Machine weight approx. 2500 kg - Tank capacity approx. 100 liters - Hand protection guard in the area of the control panel and opposite - Color scheme: Housing RAL according to customer requirements Protective guard/knife bar RAL 1028 melon yellow Godpfx Aoftnt Nsciskb Made to order Price and further information on request.

Condition: good (used), Year of construction: 1995, shredding by 3 HARDOX-coils (spirals) diameter x length: approx. 500 x 1.700 mm opening: approx. 1.100 x 1.700 mm new base frame with steel construction Godpfxjl I Dx Nj Acijkb new feed-hopper 8 m³ new control cabinet incl. 7 unused spare coils

Condition: reconditioned (used), Max. forming area: 960 x 660 mm Min. forming area: 210 x 170 mm Max. sheet size: 1000 x 700 mm Min. sheet size: 310 x 210 mm Max. sheet thickness (manual feeding): 12 mm Max. sheet thickness (automatic feeding): 10 mm Max. tool height: 490 mm Max. draw depth: 300 mm (positive/negative) Total power consumption: approx. 64.0 kW / 115 A Technical features: - Siemens Simatic S7-300 control, OP 37 panel - Air-conditioned control cabinet - Top heater with 5 temperature control circuits via pilot emitters - Bottom heater with 5 temperature control circuits via pilot emitters - Individually switchable top heating elements - Individually switchable bottom heating elements - Parallel clamping frame - Pneumatic motor locking for the upper reduction frame - Cylinder locking for the lower reduction frame - 4 cooling fans - Adjustable vacuum for the lower table via cascade control - Pre-blow and demolding adjustable via cascade control - Large front opening for tool change - Film sag control by photocell with support air - Automatic tool change system Lower table: 1. Tool clamping via vacuum 2. Tool change via pneumatically operated ball rollers Upper punch: 1. Motorized remote adjustment for stroke limitation 2. Pneumatic quick-change system for tools Sheet feeding: - Automatic motorized lifting of the film transport chain - With pneumatic quick-clamping system for vacuum plates - Motorized centering of plastic sheets - Separate vacuum pump for grained material Gedpfx Ajwf Dvajcijkb Optional preheating retrofit: - Pneumatically moved top heater, complete zone control, each emitter individually switchable via toggle switch - Pneumatically moved bottom heater, complete zone control, each emitter individually switchable via toggle switch - Temperature control of top and bottom heating via separate heating controllers in the BE control cabinet (temperature setting not via UA control panel) Optional retrofit for roll processing: - Cross cutter and feeding rollers in feed area - RO 800 roll stand

Condition: new, Year of construction: 2026, A superfine ball mill is a type of milling machine that is used to grind materials into very fine particles. This type of ball mill has some distinctive features that make it especially suitable for processing even the hardest materials with low contamination and minimal wear. It is commonly used in various industries, including pharmaceuticals, minerals, pigments, and chemicals, for producing micro powder or nanoparticles. Here are some key features and considerations for a superfine ball mill for micro powder: 1. High Grinding Efficiency: Superfine ball mills are designed to achieve high grinding efficiency by utilizing grinding media with a relatively small size, leading to a large surface area for grinding. 2. Precision Control: These mills often come with advanced control systems to regulate parameters like rotation speed, temperature, and grinding time, allowing precise control over the particle size distribution. 3. Specialized Design: The mill is typically designed with features to minimize contamination, such as using materials resistant to wear and corrosion. Some mills also have cooling systems to prevent overheating during the milling process. 4. Variety of Materials: Superfine ball mills can handle a wide range of materials, including both brittle and fibrous substances. They are often used for milling hard materials that require fine grinding, such as ceramics, minerals, or pigments. 5. Size Reduction to Micro or Nano Level: The primary goal of a superfine ball mill is to reduce particle size to the micro or even nano level. This is achieved by the intense grinding action that occurs within the mill. 6. Classifier System: Some superfine ball mills incorporate a classifier system to control the particle size distribution more precisely. This allows for the separation of fine particles from coarser ones during the milling process. 7. Batch or Continuous Operation: Depending on the specific design, these mills can operate in either batch or continuous mode, offering flexibility based on the production requirements. Gsdpfjq Nf Uwex Aciokb 8. Safety Measures: Safety features may be included, such as monitoring and control systems to prevent overloading, overheating, or other potential issues during operation. When selecting a superfine ball mill for micro powder production, it's important to consider the specific requirements of your application, the characteristics of the materials you're working with, and the desired final particle size distribution. Always follow the manufacturer's guidelines for operation, maintenance, and safety to ensure optimal performance and longevity of the equipment.

Condition: new, Year of construction: 2023, machine/vehicle number: 7YXXX, VIS G is the ideal and the most efficent solution for serap processing like stampings, trimmings, wires mostly recommended for the automotive industry, metal recyclers and non-ferrous metal remelting industry. Gjdpfsmqi Aksx Acijkb