Panel-Drilling Machine

Serrmac FDR 18

Condition: good (used), Year of construction: 1962, High speed radial drilling machine, radial drilling machine, drilling machine, boom drilling machine, high speed radial drilling machine -Clamping table: 400 x 1100 mm -Projection: 930 mm -Taper mount: MK4 Iodpfx Aoirax Ujatsif -Engine power: 1.35/1.8 kW -Speed: 41-1700 rpm -Columns: Ø 200 mm -Spindle stroke: 125 mm -Thread cutting device: YES -Feed: 0.075 - 0.3 mm/rev -Dimensions: 1800/1235/H2240 mm -Weight: 1500kg

Condition: used, Year of construction: 1993, Technical details: sheet width: 3050 mm plate thickness: 6,0 mm distance between columns: 3460 mm no. of strokes: min./max.: 9 / 17 Hub/min back gauge: 750 mm (motorisch) mm cutting angle: 0,5° - 3,0° ° cutting gap adjustment: manuell mm down holder: 18 Stück (hydraulisch) Stück Table dimensions: 380 x 3100 mm total connected load: 7,5 kW weight of the machine ca.: 4,56 t dimensions of machine: L: 3,64 x B: 2,55 x H: 1,58 m Equipment: With side stop L: 1000 × W: 100 × H: 60 mm and stop bar 990 mm, with 8 supports Operation via control panel and foot switch Cutting zone lighting Stroke counter Machine feet * Iisdpfou Rni Hox Aatjf

Condition: new, Year of construction: 2025, Bending machine ZB 70/2 M - with foot pedal - with standard roller set Iiodpjt Hwfnjfx Aatof - two driven shafts - mecanical adjusting of the center roller - working position horizontal and vertical - shafts are supported by conical bearings - slide bars on the slide -support are exchangeable - shaft diameter: 40 mm - roller diameter: - shaft rpm: 8,5 U/min - voltage: 400V 50Hz 3Ph - drivingmotor: 1,1 kW - adjusting way: 120 mm - weight: 400 kg - dimensions: 900x600x1100 mm

Condition: good (used), Table milling machine, table milling machine -Table milling machine: with rigid spindle -Speeds: rpm -Motor power: kW -Dimensions: 1000/1870/H1040 mm -Weight: 560 kg Iisdpfecl Svvsx Aatof

Condition: excellent (used), Year of construction: 1997, Romanian Lathe SARO SPS 1250x9000, Manufacturer: Saro Targoviste, Year of Manufacture: 1997. Chuck diameter: 1250 mm, Maximum swing over bed: 1250 mm, Spindle diameter: 250 mm, Distance between centers: 9000 mm, Maximum swing over slide: 920 mm, Maximum workpiece weight between centers: 15,000 kg. Grinding attachment available! Video of the machine under power available. Weight approximately 25 tons. Iiodpfjy Icbaex Aatjf

Condition: ready for operation (used), An old Colchester engine lathe is available. Center height: 216mm, swing diameter over bed/cross slide/in gap: 432mm/267mm/711mm, distance between centers: 2000mm, spindle bore: 76mm, speed: 1600rpm, bed width: 343mm. Machine dimensions X/Y/Z: approx. 3200mm/1100mm/1400mm, weight: approx. 2500kg. An on-site inspection is possible. Iedpey E S D Eofx Aateif

Condition: used, Year of construction: 1991, bore capacity in steel (diameter) 50 mm arm length 1100 mm workpiece height max. ca. 1000 mm bore capacity in cast iron 60 mm spindle taper MK 5 spindle turning speed range 28 - 2500 U/min feeds 0,05 - 2 mm/U quill stroke 300 mm distance basic plate - spindle nose 630 - 1380 mm crossrail adjustment vertical 750 mm total power requirement 6 kW weight of the machine ca. 4 t dimensions of machine L x W x H 2,74 x 1,14 x 2,59 mm Iodpsu Sblwefx Aatsif - with thread cutting attachment - Accessories: box table 550 x 550 x 550 mm, vice, coolant

Year of construction: 2011, condition: excellent (used), Cloos welding robot Qirox QRC 320 incl. control system V 6, stand base for vertical arrangement, Cloos welding machine Quinto II 603 (600 A), wire feeder, welding torch, torch hose package, mechanical cleaning, pressure amplifier 1 tilting and rotating table WPK 5000, load capacity 500 kg, 1 start pre-selection, 1 control unit for customer-supplied sliding door Iodsizwv Njpfx Aateif Gas nozzle sensor, arc seam tracking, point editor System will be completely overhauled and serviced before delivery. A second station with another identical tilting and rotating table is possible.

Condition: used, Year of construction: 2000, With electric height and tilt adjustment Used, excellent condition, little used Make Altendorf Type F45 Year of manufacture 2000 Machine number GS-tested Motor 4 kW Steel guides Carriage length approx. 3000 mm Cutting width approx. 1050 mm Pivoting up to 45° Prepared for scoring unit Ijdpevxlq Hefx Aateif Parallelogram guard Tabletop extension Anodized aluminum parts Electric height adjustment Electric tilt adjustment Digital display: - Cutting angle - Speed Extraction connection D 120/80 mm Space required approx. 3010 mm x 1800 mm x 1500 mm Weight approx. 1000 kg Storage location 97447 Gerolzhofen, free on load, unpacked Sold in the current condition as seen, without warranty or guarantee

Condition: used, Year of construction: 1983, Bohrleistung in Stahl (-Ø 50 mm throat 1500 mm workpiece height max. 1380 mm Bohrleistung in Guß (-Ø 60 mm Abstand Spindelmitte bis Säule 320 - 1250 mm swival range +/- 180 ° base plate surface area 2640 x 1000 mm max. torque on the spindle 310 Nm Iodpfx Aotv Ikloatsif Bohrspindel-Ø/ Aufnahme 75 mm /MK 5 bore spindle stroke 310 mm spindle turning speed range 28 - 2500 U/min feed: 0,05 - 2 mm/U power capacity 4 kW weight of the machine ca. 4,3 t dimensions of the machine ca. 3,2 x 1 x 2,75 m cube table 500 x 500 x 500 mm