PANKOKE & KOCHSIEK BFA 05 Drilling

PANKOKE & KOCHSIEK BFA 03 PANKOKE & KOCHSIEK BFA 05 Drilling

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC Ppodpfjwp Rqfox Ampor • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Condition: new, table length 2200 mm table width 1500 mm stroke height 1850 mm weight max. in kg 2000 kg Podpfx Amjupxwkepjpr 260 mm total power requirement 1,5 kW stroke speed - idle stroke upwards 40 sek. stroke speed - idle stroke downwards 30 sek. connected load frequency 400 V weight of the machine ca. 0,45 t dimensions of the machine ca. 2,2 x 1,5 x 0,26 m The hydraulic lifting tables are electrically driven and operated. Have a contact strip for safe lowering operation. Wide applicability for workshops, assembly departments, loading pits, etc.

Condition: good (used), Year of construction: 2007, functionality: fully functional, Pellet production line based on Italian producer Zepi pellet press, hammer mill, pellet cooler and sifter. Machines are really powerful and reliable. Some parts like hammer mill are completely refurbished. Ppsdpsvx S Ryefx Ampjr Year of production 2007.

Condition: refurbished (used), DIFFERENT TYPE OF MOTOR AND SLIDE for CELASCHI DET Pjdpfsdvlcyex Ampspr SECOND-HAND, FULLY RECONDITIONED

Condition: good (used), Year of construction: 1995, functionality: fully functional, Used dipping plant, manufacturer Wichmann, type WH 6.0 - 6.0 m long x 1.75 m wide x 1.75 m high, clear internal dimensions; - Year of manufacture: 1995; - Control via SPS Moeller PS4 with program selection; - Wooden support approx. 5 m long, hold-down device approx. 5 m long with frame; - Double-walled with leakage sensor; Ppsdpfx Ajx Akq Nempsr - Internally partially rusted; - Transport dimensions: approx. 7.50 m long, 2.44 m wide, 2.98 m high (with guide rails removed); - Weight approx. 10.0 tons; - Plant empty, loaded onto truck free of charge.

Year of construction: 1991, condition: like new (used), overall weight: 1,420 kg, rotational speed (max.): 1,485 rpm, 3 stainless steel volute casing pumps in process design 2 x CPK-CM 250-315 built in 1991 1 x CPKN-C1 250-315 year of construction 2011 !!! Price per piece !!! Pumps were operated on a test bench and all have very few operating hours! See pictures !!! Flow rate: 1001 m³/h (278 liters / second) Delivery head / delivery pressure: 18 m / 1.8 bar Pump speed: 1485 1/min NPSH: 5.00 m Shaft seal: single mechanical seal with sealing water Manufacturer: Burgmann Impeller type: closed centrifugal impeller Impeller diameter: 324mm Bearing type: roller bearing Lubrication type: Oil Lubricant monitoring Oil level controller Materials: 1.4408 (AISI 316) Pump housing: 1.4408 (AISI 316) Wear plate: 1.4408 (AISI 316) Pressure cover: 1.4408 (AISI 316) Shaft: Heat-treated steel C45+N Impeller: 1.4408 (AISI 316) Bearing bracket lantern: Gray cast iron JL1040 Shaft sleeve: CrNiMo steel Nominal diameter of suction nozzle: DN 300 Discharge connection Nominal diameter: DN 250 Nominal pressure suction side: PN 16 Nominal pressure pressure side: PN 16 Coupling manufacturer: Flender Coupling type: Eupex NH without intermediate sleeve Base plate: Painted gray cast iron Motor manufacturer: VEM K21R 280S4-Z Efficiency class: IE 0 Motor speed: 1480 1/min Frequency: 50 Hz Psdpeqabiajfx Ampopr Rated voltage: 400 / 690 V Rated motor power: P2: 75 kW Thermal class: F Motor protection class: IP55 Cosphi: 0.86 Dimensions: Length: 2120 mm Width: 950 mm Height: 1090 mm Weight: 1420 kg

Condition: excellent (used), Year of construction: 2008, Machining center Manufacturer: Weeke Type: BHX 500 Year of manufacture: 2008 machining dimension X: 2.500 mm machining dimension Y: 1.300 mm Machining dimension Z: 4 - 80 mm Number of milling units. 2 Number of drilling units: 2 Drilling spindles vertical: 72 drilling spindles horizontal X: 16 drilling spindles horizontal Y: 4 grooving saw: 90° tiltable speed X-axis: 130 m/min Pedpoh E Sghefx Ampspr speed Y-axis: 80 m/min speed Z1-axis: 50 m/min speed Z2 axis: 27 m/min Speed: 18.000 rpm Disassembled - directly available

Condition: good (used), Year of construction: 2000, functionality: fully functional, Cambio 500 debarking line consisting of: Infeed centering. Ppsdpfx Aswxdimsmpor Cambio 500: Rotor opening 495 mm. Minimum log diameter 90 mm. Drive motor 55 kW. Feed motor 11 kW. 80 m/min. Hydraulic rotor and feed rollers. Outfeed control unit. Tilting trough for long timber. Spare parts.

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, overall weight: 36,000 kg, oil tank capacity: 1,300 l, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Psdpfjvf E Avjx Ampjpr Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: new, Year of construction: 2022, Dowel hole drilling device: no Drilling depth: 150 mm oblong hole length: 180 mm Podjgq Un Aepfx Ampepr Height adjustment travel: 145 mm Motor power: 1,5kW Speed: 3000 rpm Suction connection: 100 mm Machine length: 1280 mm Machine width: 960 mm Weight: 240 kg