Used Weber Ta 2200 for sale (91)

Condition: good (used), Weber RSM 600 Index Cutting Machine Bodpfx Afjx N D T Hs Escu Machine in very good condition, ready for production. This machine cuts registers from finished bindings and loose sheets. Manufacturer’s description: Automatic cutting by activating two manual buttons. Interchangeable knife shapes. Material holding pressure. Capable of cutting large stacks of material in a single pass. Safety guards ensure safety. 380V power supply + compressed air. Stack height for a single cut is approximately 30mm. Approximate dimensions: 120x120x180cm, weight: 900kg.

Condition: ready for operation (used), Year of construction: 1995, operating hours: 39,000 h, functionality: fully functional, Equipment: documentation/manual, A used and functional profile line for rigid PVC-profiles, consisting of: Twin-screw extruder (parallel) Manufacturer: WEBER Type: DS 7.22 Year of manufacture: 1995 Machine no.: DS70-043 Operating hours: 39,000 hours Screw diameter: 70 mm Effective screw length: 22 x D Screw geometry: for rigid PVC profiles Torque: 4,500 Nm per screw Screw speed: max. 40 rpm, continuously adjustable Drive motor: DC low-voltage motor, thyristor-controlled Drive power: approx. 25 kW Cylinder heating/cooling zones: 5/3 (air cooling with fan) Adapter heating zone: 1 Tool heating zones: 5 Control: conventional control with digital temperature controllers Degassing: Busch rotary vane vacuum pump (1.5 kW) Output capacity, max.: 120-150 kg/h for hard PVC, depending on material Connected load: approx. 50 kW (without tool) Special accessories: Mass temperature sensor and mass pressure sensor Adapter between extruder connection and extrusion tool Used tool set for a window profile (widening), consisting of: - Extrusion tool ‘widening’, incl. heating bands - Dry calibration - Vacuum tank approx. 2 m long, with 8 slots for calibration discs - 16 calibration discs Vacuum calibration unit Manufacturer: Uniplast / Greiner Type: CAL VAK 4P Year of manufacture: 1992 Machine number: K9209590 Total length: 6500 mm Vacuum pumps: 4 x Speck vacuum pumps (4.3 kW each) Water circulation pumps: 2 x Calpeda (1.1 kW each) Caterpillar haul-off, incl. attached saw Manufacturer: Uniplast / Greiner Type: CAT PUL 2D Year of manufacture: 1992 Machine number: R 9204546 Haul-off: Effective contact length: 2000 mm Pad width: 250 mm Haul-off force, max.: approx. 25000 N Speed range: approx. max. 10 m/min. Profile saw: HM circular saw blade: Ø 450 mm Profile cross-section, max.: approx. 300 x 100 mm Tilting table Manufacturer: Ide Type: ME N 52/2 Year of manufacture: 1994 Length: 6000 mm Support width: 270 mm Bcodpfxoxu U Tro Af Esu Note: The complet profile line was overhauled in 2020 and has only been in operation for 325 hours since then.

Condition: used, mileage: 1,001 km, power: 4 kW (5.44 HP), gearing type: other, fuel type: diesel, color: yellow, first registration: 01/1999, Year of construction: 1999, driver cabin: other, Vehicle location: Bovenden, Hatz Diesel Engine E 673LS! Bcsdpoxy Swxsfx Af Eeu Forward and reverse gear! The exact year of manufacture and power output cannot be determined as there is no type plate present! Equipment details provided without guarantee; subject to change, prior sale, and errors!

Condition: used, mileage: 1,001 km, power: 3 kW (4.08 HP), gearing type: other, fuel type: gasoline, color: blue, empty load weight: 103 kg, first registration: 01/2017, Year of construction: 2017, driver cabin: other, Vehicle location: Bovenden, Honda GX 160 petrol engine! Includes rubber mat! ACCESSORY DETAILS WITHOUT GUARANTEE, subject to change, prior sale and errors excepted! Bsdpfx Afsxy Sw Ee Eecu

Year of construction: 1991, operating hours: 102,364 h, condition: good (used), This extrusion line from Hans Weber GmbH is in machine storage at Plastima Used Machinery. The line is from 1991 and is in used but good condition. - Brand: Hans Weber GmbH - Model: WEBER DS 6.5 - Year of construction: 1991 - Screw Ø: 65 mm - Working hours: 102.364 Bcedpfx Aoqpft Ief Eju

Year of construction: 1997, condition: used, functionality: fully functional, machine/vehicle number: DS 70 087, WEBER DS 7.22 Twin Screw Extruder Bcedpfx Aoxghz Hef Eeu

Year of construction: 1997, operating hours: 58,668 h, condition: good (used), This WEBER extruder is in machine storage at Plastima Used Machinery. The machine is from 1997 and is in great condition. Make: Hans Weber GmbH Model: NE 7 042 Screw type: single screw Year of construction: 1997 Bjdpfx Afotpg Dns Eocu Propeller Ø: 75mm Working hours: 58,668

Condition: good (used), functionality: fully functional, Working from production, has always run with an 800 mm extrusion head for producing HDPE pipes. Bcsdpfxjwr Db No Af Esu

Year of construction: 1997, operating hours: 76,200 h, condition: good (used), This WEBER extruder is in machine storage at Plastima Used Machinery. The machine is from 1997 and is in great condition. Bjdpjtpg D Ujfx Af Eecu Make: Hans Weber GmbH Model: NE 7 048 Screw type: single screw Year of construction: 1997 Propeller Ø: 75mm Working hours: 76,200

Year of construction: 1991, operating hours: 32,000 h, condition: refurbished (used), • One pair of original WEBER screws (excellent condition, including measurement report • One pair of non-original screws • Gearbox inspected and partially revised by WEBER • Control upgraded to WPS control • Output on PVC around 700 kg/hour Bcjdpfx Afjwaxuaj Eju

Condition: used, Year of construction: 2002, Burkhart & Weber MCX 900 – 4-Axis Machining Center - Siemens SINUMERIK 840D CNC control - Double pallet changer, pallet at loading station rotatable, total pallets: 6 - Rack-type tool magazine with 264 tool positions and tool setup station for loading during runtime - Rapid traverse X/Y/Z: 40 m/min / B-axis: 20 rpm - Max. machining force X/Y/Z: 20 kN / Tangential torque B-axis: 20,000 Nm - Renishaw wireless probing system - Year of manufacture: 2002 Technical Data Working ranges: - X-axis: 1,600 mm - Y-axis: 1,400 mm - Z-axis: 1,500 mm - B-axis: 360° / 0.001° Speeds: Bodpfx Ajxxbbwsf Eocu - Spindle speed: 20 – 6,000 rpm - Gear ranges (2): 20–1,400 / 1,401–10,000 rpm Feed rates and forces: - X/Y/Z-axis rapid traverse/feed: 40,000 mm/min / 20,000 N - B-axis speed/torque: 20 rpm / 20,000 Nm Tool magazine: - Magazine type: rack magazine - Number of tools: 264 Tools: - Max. tool weight: 60 kg - Max. tool length: 560 / 750 mm - Tool holder: DIN 69893 / HSK A-100 - Tool clamping force: 40 kN Pallets: - Pallet size: 800 x 1,000 mm - Pallet changer: double - Pallet weight: 800 kg - Max. allowable pallet weight: 3,150 kg - Pallet design: T-slots - Workpiece loading station: manually rotatable (4 x 90°) Coolant system: - Internal coolant (through tool): 30 l/min / 50 bar - External coolant: 200 l/min / 4 bar Drive power: - S1 operation 100% duty cycle: 37 kW - S6 operation 40% duty cycle: 50 kW Electrical: - Voltage: 3 x 400 V / 50 Hz +10% - Control voltage: 230 V AC / 24 V DC - Rated current: 130 A - Connected load: 65 kW / 75 kVA Hydraulics: - Tank: 240 l - Pressure: 60 bar Pneumatics: - Pressure: 4 – 6 bar - Consumption: 10 m³/h

Condition: used, functionality: fully functional, fuel type: gasoline, overall weight: 32 kg, DGUV certified until: 03/2026, Year of construction: 2018, machine/vehicle number: 20008074, Equipment: UVV, Specifically designed for compaction of pipe collars in trenches. Other areas of application: compacting edge zones of walkways; installation of drainage systems. Due to its low weight, it is easy, flexible, and safe to operate even on slopes and in very confined spaces. Bcedpexpu Tbsfx Af Eeu

Year of construction: 2005, condition: refurbished (used), functionality: fully functional, Twin parallel screw extruder - Manufacturer: WEBER - Type: DS 8.5 - Year: 2005 - Double parallel screws ø85mm 17D - 5 heating zones on the cylinder + 2 cooling zones - 5 tool heating zones - Engine power: 56kW - Up to 150kg/h profile - 230kg/h tubes Very good condition Bsdpfx Aeuziyhsf Ejcu

Condition: used, Vibratory Feeder with Pneumatic Screwdriver Stand Eco Line Vibratory Feeder, Sorting Device, Bowl Feeder, Vibratory Bowl, Automatic Screwdriver WEBER Type ZSU 24 Machine No.: 1113212 Year of Manufacture: 2003 Vibratory Feeder WEBER ZSU 24 Bowl diameter: 240 mm Bowl internal height: 70 mm Sorting track width: 10 mm Power supply: 230 Volt, 50 Hz Operating pressure: 6 bar (for singulation and screws) Control voltage for pneumatic valves: 24 Volt - Controller for infinitely variable vibration speed = infinitely variable transport speed - Vibratory bowl in protective enclosure - With pneumatic feeding system - Feed impulse via external electrical control - The feeder was used for feeding screws M5 x 12 mm - Some pneumatic hoses need to be replaced - Siemens S7-200 CPU 224 PLC MISSING Space requirements vibratory bowl L x W x H: 450 x 450 x 315 mm Vibratory bowl weight: 32 kg WEVER Eco Line Screwdriver Stand Guide column: Ø 60 x 525 mm Height adjustment: 345 mm Primary stroke pneumatic cylinder 1 FESTO DZF-32-125-P-A-SM: 115 mm Screwdriver holder diameter: Ø 50 mm Secondary stroke pneumatic cylinder 2 FESTO: 30 mm Screwdriver guide diameter: Ø 37 mm Distance screwdriver guide to table: 135 - 465 mm - 1 piece flat cylinder FESTO, Type DZF-32-125-P-A-SM - 1 piece flat cylinder FESTO, Type probably DZF-32-30-P-A-SM - Screwdriver linear motion frame on linear guide - 3 position sensors on the cylinders - Festo pressure switch - Bosch pneumatic valve Screwdriver stand dimensions W x D x H: 200 x 410 x 1050 mm Screwdriver stand weight: 35 kg good condition Total weight vibratory feeder and screwdriver stand: 67 kg Attention: The original Siemens S7-200 CPU 224 PLC is missing (see picture control cabinet without PLC), therefore, an automatic process is not possible in this condition. The control system also managed the separations of the screws and controlled the screwdriver itself. The vibratory bowl is fully functional even without the PLC, the built-in vibratory bowl controller does not require PLC control. Process: Fasteners are filled into the bowl in bulk and conveyed upward by mechanical vibration (micro-throw principle). The vibratory bowl is automatically switched on or off depending on the fill level of the screw magazine. The screw is then conveyed by compressed air through a plastic hose to the downstream device. The feed impulse for each individual screw is triggered externally by the downstream device. Bcodpfxoxf Up Uo Af Eeu

Year of construction: 1979, operating hours: 216 h, condition: reconditioned (used), functionality: fully functional, Twin-screw extruder, parallel Manufacturer: Hans Weber Maschinenfabrik GmbH Type: DS 85 Year of manufacture: 1979/2022 Machine no.: 85-399 Screw geometry: for PVC-hard profiles Screw diameter: 2 x 85 mm Screw length: 17 x D Screw speed: max. 30 rpm Screw torque: 10000 Nm Bcjdpfx Ajxlcfksf Eeu Motor power: 3.3 - 25.0 kW Drive motor: commutator motor Elektra Faurndau Cylinder heating/cooling zones: 4/2 (air cooling with fan) Tool heating zones: 8 Temperature control: 12 x digital temperature controllers (PMA KS40) Accessories: Melt pressure sensor and melt temperature sensor Connected load: approx. 60 kW (without tool) Extrusion height: 1100 mm Output capacity: approx. 150 - 180 kg/h for PVC-hard profiles Accessories: Material hopper and connection flange Accessories: Vacuum pump (1.1 kW) incl. material separator Dimensions: 4500 x 1200 x 2100 mm (LxWxH), incl. material hopper Weight: approx. 4000 kg Note: The electrical control cabinet was completely renewed approx. 3 years ago. Since then, the extruder has only been in operation for 216 hours. Condition: The extruder was repainted (light gray, RAL 7035) and checked for function.

Year of construction: 2011, condition: good (used), - Incl. extruder, corrugator, cutting saw, sliding saw, table, molds and die head / set Bedpfx Aeua E H Sjf Ejcu - Suitable for single wall pipes up to 220mm

Condition: used, Year of construction: 2013, functionality: limited functionality, 1x Werner & Weber press container with 8 holders. Bcsdpfeunafajx Af Eeu

Condition: excellent (used), Year of construction: 2002, functionality: fully functional, Saw for profiles, used Manufacturer: Weber - Kronach Type: PS 2 Year of manufacture: 2002 Profile section: max. 200 x 100 mm (W x H) Saw blade diameter: 400 mm Connection load: 5,0 kW. Bsdpfow Up Rmsx Af Eocu Spannung: 400 V, 50 Hz Condition: very good, like new

Condition: like new (used), Extruder pants pieces for Weber DS 10.22 Bcodpjhlvm Nefx Af Eju

Year of construction: 2004, condition: excellent (used), WEBER 3 layer PVC foam core pipe system with: 2 WEBER DS 9.25 DOUBLE SCREW EXTRUDER Year of manufacture 2004 WEBER DS 9.25 DOUBLE SCREW EXTRUDER Year of manufacture 2004 Application PVC foam core pipe (three layer) Only the extruders are sold, without feed block The screws and cylinders of the two extruders are in very good condition Bcodpot Rcn Njfx Af Eou The system is in very good working order The system is my property Sahal Extrusionsmaschinen D-26345 Bockhorn-Grabstede Germany

Condition: used, Spreading and pressing device with hydraulic unit WEBER type E45 / 59600.0 High-pressure unit + hydraulic spreader pliers, hydraulic spreader Year of manufacture 1988 / 1986 Hydraulic unit type E45 / 59600.0 Maximum operating pressure: 630 bar Flow rate: approx. 2 l/min Tank capacity: approx. 10 liters Spreader device - pliers WEBER type SP30 / 059 198.0 Reach (arm length): 340 mm Maximum spread distance: 810 mm Maximum spreading force in working range: 132 kN Closing force: 99 kN - Twin hose with quick-connect coupling Rated power: 0.9 kW Power supply: 220 Volt, 50 Hz Weight of hydraulic unit: approx. 40 kg Weight of spreader device: approx. 25 kg Bjdpedzp S Refx Af Eecu Very good condition Hydraulic rescue set for fire brigades with hydraulic power unit and a spreader. The spreader is used to create rescue openings after traffic accidents by spreading apart structures. Also suitable for compressing or lifting loads. Versatile in use due to the multifunctional design of the spreader jaws, made of drop-forged and hardened steel.

Condition: new, Offered is an attachment block broom Kehrfix in different versions from 1.50 m to 4.00 m width. A pick-up must then still be discussed separately if this is desired (e.g. pallet fork pick-up, shovel hook or Euro pick-up). An attachment block broom for forklifts, wheel loaders, tractors, mini-loaders, mini-dumpers and many other vehicles and equipment! With various attachments for quick mounting on a variety of vehicles, the KehrFix is the perfect aid for keeping larger areas clean. Bsdpfoh T A Tnox Af Escu The KehrFix push brooms are a professional choice for easy and effective sweeping and cleaning. The rugged KehrFix is designed to get the job done quickly and thoroughly in every conceivable application. KehrFix push brooms are high-quality, durable, maintenance-free and universally applicable sweeping systems.

Condition: new, Year of construction: 2024, Facility managers and property managers know the problem: On the due date, i.e. when the garbage truck empties the garbage cans, all the garbage cans must be at the collection point. If the garbage cans are normally in the underground garage, the caretaker has to janitor has to take all the garbage cans up the ramp of the underground garage. up the ramp. This is time-consuming and exhausting or even impossible Bcedpfoi Nnruox Af Eju impossible. A 240 kg garbage can filled with waste paper can weigh over over 200 kg, a 1100 liter waste container even weighs over a ton. even over a ton. If this is the case, the janitor needs the help of a second person. This is cost-intensive. Weber offers time and health-saving solutions to this problem. problem. Talk to us about our waste garbage can frames for 1100 liter waste containers and our waste garbage can trolleys for 120 and 240 liter garbage cans. By the way, battery-powered towing vehicles are of course also available from us. gentle on health effective 400 kg payload galvanized can be coupled together Professional device - not for public road traffic Adapter: Ball head Trailer hitch

Year of construction: 2017, condition: excellent (used), Bluhm weber legi-air 4050 labeling machine Bcodpfx Afofp A I Es Esu More pieces in stock! year built: 2016-19 Print resolution 8 dots/mm (203 dpi) 12 dots/mm (300 dpi) 24 dots/mm (600 dpi) Print speed Up to 400 mm per second Tamp sizes (mm) Tamp-Blow standard of 12.5 x 7 to 160 x 300 mm, label lengths must be limited in accordance with label quality, longer or smaller labels are possible using special tamps Label gap Minimum 3 mm Label roll 300 mm diameter, up to 450 running meters, core 76 mm (3"), outside winding (optional inside winding) Data interfaces RS232, RS422, RS485, Ethernet Optional: Profibus Dimensions (L x H x W) 770 x 560 x 580 mm, Applies to system with 250 mm stroke Display controller Multi-language operator guidance 5.7" VGA touch display Service interval indicator Polling, editing and saving of label data USB connection for memory medium or keyboard Compressed air connection 6 bar, the compressed air must be clean, dry and oil-free

Condition: ready for operation (used), total length: 2,050 mm, total width: 850 mm, total height: 1,350 mm, overall weight: 300 kg, WEBER desulphurizer. Type - ASB 1000 Belt dimensions - Length - 205cm. Width - 40cm. Infeed - 90cm. Exit - 113cm. Roller width - 48cm. Total dimensions - Length - 205cm. Width - 85cm. Height - 135cm. Weight - 300kg. TJ. Bcjdpforq Dmcsx Af Eeu