Used Vertical Borer for sale (7,375)

Condition: used, WEBSTER & BENNETT EV 36” HIGH SPEED VERTICAL BORER MAKE WEBSTER & BENNETT, MADE IN ENGLAND MODEL EV 36” TABLE DIA 915 mm SWING 1168 mm HEIGHT UNDER RAIL 533 - 1016 mm SPEED 13.5 - 300 rpm FEED RATE 0.005-0.250 inch/min MAIN SPEED 40 HP PLUS HIGH SPEED TAABLE EV SERIES MACHINE ELEVATING RAIL SAFETY GAURDING SET OF JAWS FULLY FUNCTIONAL GOOD SLIDES Gusdpfxsxp Na Nj Afcsa

Condition: new, Year of construction: 2024, New Grundfos Pump - Vertical, multistage centrifugal pump with integrated frequency converter. inlet and outlet ports on same the level (inline). The pump head and base are in cast iron – all other wetted parts are in stainless steel. A cartridge shaft seal ensures high reliability, safe handling, and easy access and service. Power transmission is via a rigid split coupling. Pipe connection is via DIN flanges. The pump is fitted with a 3-phase, fan-cooled asynchronous motor. The motor includes a frequency converter and PI controller in the motor terminal box. This enables continuously variable control of the motor speed, which again enables adaptation of the performance to a given requirement. An operating panel on the motor terminal box enables setting of required setpoint as well as setting of pump to "Min." or "Max." operation or to "Stop". The operating panel has indicator lights for "Operation" and "Fault". Communication with the pump is possible by means of Grundfos GO Remote (accessory). The remote control enables further settings as well as reading out of a number of parameters such as "Actual value", "Speed", "Power input" and total "Power consumption". The terminal box holds terminals for these connections: • pump start/stop input (potential-free contact) • remote setpoint setting via analog signal, 0-10 V, 0(4)-20 mA • 10 V voltage supply for setpoint potentiometer, Imax = 5 mA • three analog sensor inputs, 0-10 V, 0(4)-20 mA Guedpfxeyug R Re Afcsa • 24 V voltage supply for sensor, Imax = 40 mA • one analog output • three digital inputs • two Pt100 inputs • two potential-free fault signal relays with changeover contact, reporting "Fault", "Operation" or "Ready" • RS-485 GENIbus connection • interface for Grundfos CIM fieldbus module

Condition: new, Year of construction: 2024, NEW Grundfos - The pump is fitted with a 3-phase, fan-cooled, permanent-magnet, synchronous motor. Gedpsyug Hxsfx Afcoua The motor efficiency is classified as IE5 in accordance with IEC 60034-30-2. The motor includes a frequency converter and PI controller in the motor terminal box. This enables continuously variable control of the motor speed, which again enables adaptation of the performance to a given requirement. An operating panel on the motor terminal box enables setting of required setpoint as well as setting of pump to "Min." or "Max." operation or to "Stop". The Grundfos Eye indicator on the operating panel provides visual indication of pump status: "Power on": Motor is running (rotating green indicator lights) or not running (permanently green indicator lights) "Warning": Motor is still running (rotating yellow indicator lights) or has stopped (permanently yellow indicator lights) "Alarm": Motor has stopped (flashing red indicator lights). Communication with the pump is possible by means of Grundfos GO Remote (accessory). The remote control enables further settings as well as reading out of a number of parameters such as "Actual value", "Speed", "Power input" and total "Power consumption". The terminal box has a number of inputs and outputs enabling the motor to be used in advanced applications where many inputs and outputs are required: • two dedicated digital inputs • three analog inputs, 0(4)-20 mA, 0-5 V, 0-10 V, 0.5 – 3.5 V • 5 V voltage supply to potentiometer and sensor • one analog output, 0-10 V, 0(4)-20 mA • two configurable digital inputs or open-collector outputs • two Pt100/Pt1000 inputs • LiqTec, dry-running protection sensor input • Grundfos Digital Sensor input and output • 24 V voltage supply for sensors • two signal-relay outputs (potential-free contacts) • GENIbus connection • interface for Grundfos CIM fieldbus module.

Condition: used, functionality: unexamined, total height: 5,000 mm, total width: 1,200 mm, total length: 3,600 mm, input voltage: 400 V, input frequency: 50 Hz, DenoLift Vertical Carousel / Paternoster approx. 5 m – Fully Functional – Industrial We have a used DenoLift carousel (paternoster) that we are considering selling and would like to know if this system might be of interest to you. Specifications (indicative): Brand: DenoLift (Denocard) Type: vertical carousel / paternoster Dimensions: approx. 3.6 meters long × 1.2 meters wide Height: approx. 4 – 5.5 meters Control: numeric keypad with LED display (older model) Price: 5000 EUR This is an industrial storage system with significant capacity. The installation is currently set up and can be dismantled and collected by arrangement. Guodpfx Afsyplqrscoa Upon request, we can provide additional photos, a video of the system in operation, and any available technical data.

Condition: excellent (used), Horizontal/vertical rotary table Chuck: Ø 350 mm Guedpfx Aeyr Numsfcoa Shelf diameter: Ø 400 mm Height without mandrel: 140 mm Total height: 250 mm Base dimensions: Length 430 mm x Depth 370 mm Weight: approx 150 kg Possibility to work horizontally or vertically The increment is done by the front handle

Condition: good (used), Year of construction: 2012, functionality: fully functional, Schiess CNC vertical lathe with C axis, year 1992, retrofitted in 2012 Gusdexpqm Rspfx Afcoa CNC: NUM 1060 FLEXIUM 2 tables, table diameter 2000mm – max turning diameter 2500mm – max table speed 201 rpm – table power 56 KW Load capacity (table included): 16,000kg Movable crossrail with 12 positions, 50mm pitch Available space under spindle nose: min. 795mm, max. 1345mm RAM Z stroke: 1000mm C axis with 360,000 positions – milling spindle max speed 1600 rpm – milling spindle power 22KW – 2 gear ranges Tool magazine: 20 turning tool positions, 35 milling tool positions 1 milling head WIDAFLEX UTS80 1 milling head ISO 50 Renishaw MP60 touch probe (for parts) Tool presetter – Transmit function: G20 / G21 – No rigid tapping Chip conveyor Front door: partial opening M0 / full opening

Condition: new, functionality: fully functional, power: 250 kW (339.91 HP), fuel type: electric, color: other, overall weight: 19,000 kg, Year of construction: 2026, These high-speed crushers are manufactured in two different combinations as open rotor and closed rotor. Vertical shaft impact crushers (VSI) are designed with a unique rock-on-rock crushing principle, which significantly reduces the wear costs while offering superior cubical shape for the best quality fine aggregate production. The fact that it reduces their service requirements and times, and to increase their crushing performance with their low investment costs. VSI-1000 technical specifications: Model: VSI-1000 OR Capacity: 150-400 T/H Rotor Size: Ø 1000mm Maximum Feeding: 100mm Motor Power: 2 x 200-250 kW Speed: 50 – 70 ms Weight: 19000 kg General Specifications and Features: – Fine product, low wear cost, cubic shape, application flexibility and maintainability. – Rotor and crushing chute with stress relieved welding Gujdpfxey Atc Re Afcsa – Inner surfaces of the crusher is coated with wear resistant lining plates – Hydraulic opening cap – Automatic lubrication system

Year of construction: 1997, condition: repair required (used), Mortising machines Maka Db-6 v Second hand 1977 Make: Maka Model: Db-6 v Description: VERTICAL MORTISER MAKA DB-6 V Year of construction: 1977 Machine condition: very good afer repairs capital Offertype: used machine offer Location: Poland Technical data: AFTER REPARIRS VERY IMPORTENT VERTICAL Year: 1977 Gujdpfsfd Rxqex Afcja

Condition: like new (used), 30m3 insulated stainless steel tank Dim. 3.40x 6.80. 12 cm insulation, insulated with wool and metal sheet lower bottom insulated with polyurethane foam. Gujdpfxshr Rp So Afcja We offer transport with our own semi-trailer.

Condition: excellent (used), Velo Kieselgur filter vertical 10 m2 used in beverage industry, in very good condition. Complete with wiring and control desk. Guedpfjq U A Huex Afcoa

Condition: new, functionality: fully functional, power: 400 kW (543.85 HP), fuel type: electric, color: dark red, overall weight: 38,000 kg, axle configuration: 2 axles, brakes: other, Year of construction: 2026, Mobile vertical shaft crusher is a specially designed mobile stone crushing screening plant on a portable double axle chassis, consisting of feeder bunker, VSI 900 Vertical shaft impact crusher, vibrating screen and conveyor belts. It can be fed directly with the material in stream areas or it can produce sand and gravel from the sieve material in the crushing plants. The GNR - MVSI 900 Vertical Shaft Crusher that gives this facility its name; - Maximum feeding size 50-55 mm - Rotor size 900 mm - Engine power 2x200 kW - The capacity 80-210 tons per hour. For more information please call us. Gujdjwnp Akopfx Afcoa

Condition: new, Year of construction: 2025, table length: 900 mm, table width: 450 mm, number of spindles: 1, spindle speed (min.): 8,000 rpm, table load: 500 kg, VMC 650 CNC machining center, milling machine with CNC system VMC 650 machining center is a multifunctional equipment that allows you to perform milling, drilling, thread cutting, and turning operations in automatic mode (if these options are available in the machine). The VMC 650 milling machine can have 16- or 24-position tool magazine. Depending on the customer's wishes, the milling machine can be equipped with a GSK, Siemens or Fanuc CNC system. It is possible to optionally add a Y-axis drive. Gusdpfoxc I Dgox Afcoa As a very convenient additional option, we recommend installing a chip conveyor that will save you time when working with the equipment. Technical parameters: Worktable size 900x450mm Maximum workpiece weight 500 kg Movement along the axes X/Y/Z 800/450/500 mm Maximum distance from the spindle to the table surface 120-620 mm Motor power 5.5-7.5 kW Maximum spindle speed 8000 rpm Spindle type BT40 Positioning accuracy ±0.008/300 mm Repeatability ±0.005 mm Machine dimensions 300022752550 mm Machine weight 4000 kg It is also possible to supply CNC milling machines, machining centers with other table sizes: VMC 850 table 1000x500 mm VMC 855 table 1000x550 mm VMC 1060 table 1200x600 mm VMC 1160 table 1200x600 mm VMC 1275 table 1300x700 mm VMC 1370 table 1400x700 mm VMC 1580 table 1600x800 mm VMC 1680 table 1700x800 mm VMC 1890 table 2000x900 mm

Condition: ready for operation (used), Year of construction: 2004, functionality: fully functional, machine/vehicle number: KMM526 1506, travel distance X-axis: 1,000 mm, travel distance Y-axis: 400 mm, travel distance Z-axis: 360 mm, controller model: FANUC SERIES 18i-MB 5, spindle speed (max.): 12,000 rpm, No reserve price – guaranteed sale to the highest bidder! By placing a bid, you are obligated to collect the item within the specified dates, either between 11.05.2026 and 13.05.2026, or between 18.05.2026 and 21.05.2026. TECHNICAL DETAILS Travel X-axis: 1,000 mm Travel Y-axis: 400 mm Travel Z-axis: 360 mm Table dimensions: 1,500 x 470 mm Overhang: 350 mm Tool holder: SK 40 Spindle speed: 36 to 12,000 rpm Spindle bearing diameter: 65 mm Max. tool diameter: 125 mm Max. tool length: 250 mm Guodpfjym Nqkox Afcoa Feed rate X/Y/Z-axis: 1 - 10,000 mm/min Rapid traverse X/Y/Z-axis: 45 m/min MACHINE DETAILS Control: FANUC SERIES 18i-MB 5 Operating voltage: 400 V Frequency: 50 Hz Nominal current: 45 A Dimensions & Weight Dimensions (L x W x H): 2,700 x 2,700 x 3,300 mm Weight: 6,000 kg EQUIPMENT 4th axis 42-position tool changer Chip conveyor Coolant system Note: The clamping devices shown in the photos are not included. External reference: Elos – Lot 1

Condition: ready for operation (used), Year of construction: 2001, functionality: fully functional, travel distance X-axis: 510 mm, travel distance Y-axis: 510 mm, travel distance Z-axis: 460 mm, controller model: Mazatrol Fusion 640M, spindle speed (max.): 12,000 rpm, TECHNICAL DETAILS Travel X-axis: 510 mm Travel Y-axis: 510 mm Travel Z-axis: 460 mm Swivel range A-axis: +30° / -120° Rotation range C-axis: +/- 360° Feed rate range (X-/ Y-/ Z-axis): 1 - 50,000 mm/min Rapid traverse (X-/ Y-/ Z-axis): 50 m/min Indexing A and C: 0.001° Swivel time 90° A/C: 1.9 / 1.5 s Main spindle Max. spindle speed: 12,000 rpm Spindle drive power: 22/15 kW Tool holder: ISO 40 Spindle diameter: 80 mm Acceleration time to max. speed: 1.7 s Guodpfx Afeyxmq Tecea Worktable Clamping surface: 500 x 400 mm Number of T-slots: 5 T-slot width: 18 mm T-slot spacing: 80 mm Distance from spindle to table: 190 - 650 mm Max. workpiece size: 500 x 500 x 405 mm Max. table load: 300 kg Tool changer Max. number of tool positions: 40 Max. tool diameter: 80 mm Max. tool diameter with adjacent spaces free: 125 mm Max. tool length: 300 mm Max. tool weight: 8 kg Tool change time: 4.5 s MACHINE DETAILS Control: Mazatrol Fusion 640M Total power requirement: 51 kVA Dimensions & Weight Space requirement: 3.4 x 3.7 x 2.8 m Machine weight: 7.5 t EQUIPMENT Hydraulic unit Coolant system Chip tray Tool measurement Documentation

Condition: ready for operation (used), Year of construction: 1998, functionality: fully functional, travel distance X-axis: 1,250 mm, travel distance Y-axis: 880 mm, travel distance Z-axis: 800 mm, controller model: TNC 426 Heidenhain, spindle speed (max.): 12,000 rpm, TECHNICAL DETAILS Travel Range X-axis: 1,250 mm Travel Range Y-axis: 880 mm Travel Range Z-axis: 800 mm Main Spindle Max. Speed Range: 12,000 rpm Drive Power: 15 / 10 kW Godpfeyxmmnjx Afcjua Max. Torque: 500 Nm Tool Holder: SK 40 Work Table Clamping Surface: 1,500 x 1,050 mm Max. Table Load: 2,500 kg Number of T-slots: 10 T-slot Width: 18 H7 mm T-slot Pitch: 100 mm Tool Changer Number of Tool Stations: 30 Max. Tool Diameter: 80 mm Max. Tool Diameter with Empty Adjacent Pocket: 160 mm Max. Tool Length: 315 mm Max. Tool Weight: 8 kg Max. Total Weight: 100 kg Feeds Rapid Traverse (X / Y / Z axis): 15 m/min Feed Rate: 10,000 mm/min MACHINE DETAILS Control Model: TNC 430 Heidenhain Total Power Requirement: 29 kW Dimensions & Weight Space Requirement: approx. 7.0 x 5.0 x 3.3 m Machine Weight: approx. 16.0 t EQUIPMENT Documentation Chip Conveyor Coolant System High-Pressure Coolant Measuring Probe (Manufacturer: Heidenhain) Internal Coolant Supply Note: The transport rigging must be arranged by the buyer!

Condition: ready for operation (used), Year of construction: 1999, functionality: fully functional, travel distance X-axis: 1,250 mm, travel distance Y-axis: 880 mm, travel distance Z-axis: 800 mm, controller model: TNC 430 Heidenhain, spindle speed (max.): 12,000 rpm, TECHNICAL DETAILS Travel range X-axis: 1,250 mm Travel range Y-axis: 880 mm Travel range Z-axis: 800 mm Main spindle Max. speed range: 12,000 rpm Drive power: 15 / 10 kW Max. torque: 500 Nm Tool holder: SK 40 Work table Clamping area: 1,500 x 1,050 mm Max. table load: 2,500 kg Number of T-slots: 10 T-slot width: 18 H7 mm T-slot spacing: 100 mm Tool changer Number of tool stations: 60 Max. tool diameter: 80 mm Max. tool diameter with free adjacent station: 160 mm Max. tool length: 315 mm Max. tool weight: 8 kg Max. total weight: 100 kg Feeds Rapid traverse (X / Y / Z-axis): 15 m/min Feed rate: 10,000 mm/min Gujdpfxoyxmd To Afcja MACHINE DETAILS Control model: TNC 430 Heidenhain Total power requirement: 29 kW Dimensions & Weight Space requirements: approx. 7.0 x 5.0 x 3.3 m Machine weight: approx. 16.0 t EQUIPMENT Documentation Chip conveyor Coolant system Tool changer Note: Transport tackle must be organized by the buyer!

Condition: not inspected (used), Year of construction: 2001, functionality: unexamined, machine/vehicle number: 822441, travel distance X-axis: 1,020 mm, travel distance Y-axis: 510 mm, travel distance Z-axis: 600 mm, controller model: HEIDENHAIN TNC 410 PA, spindle speed (max.): 6,000 rpm, No reserve price - guaranteed sale to the highest bidder! By placing a bid, you are obliged to collect the item on time, either between 11.05.2026 and 13.05.2026 or between 18.05.2026 and 21.05.2026! TECHNICAL DETAILS Travel distances Travel X: 1,020 mm Travel Y: 510 mm Travel Z: 600 mm Spindle speed range: 40–6,000 rpm Drive power: 13 kW Spindle taper: BT 40 Number of tool stations in the tool changer: 22 Rapid traverse X and Y axes: 40 m/min Rapid traverse Z axis: 30 m/min Work table Length: 1,150 mm Width: 490 mm MACHINE DETAILS Control system: HEIDENHAIN TNC 410 PA Dimensions & Weight Dimensions (L x W x H): 2,800 x 2,400 x 2,400 mm Weight: 4,800 kg EQUIPMENT 3D probe Note: The machine vices mounted on the work table and the tool holders, including the tools installed in the tool magazine and spindle, are not included in the scope of sale and delivery. The oil mist extractor, which may be visible in the photos, is also not included in the scope of sale and delivery. Guedoyn Nvvjpfx Afcsa

Condition: not inspected (used), Year of construction: 2000, operating hours: 8,523 h, functionality: unexamined, travel distance X-axis: 1,000 mm, travel distance Y-axis: 500 mm, travel distance Z-axis: 500 mm, spindle speed (max.): 10,000 rpm, number of slots in tool magazine: 22, No reserve price – guaranteed sale to the highest bidder! Bidding obligates the buyer to collect the machine on time, either between 11.05.2026 and 13.05.2026 or between 18.05.2026 and 21.05.2026! TECHNICAL DETAILS Travel distance X: 1,000 mm Travel distance Y: 500 mm Travel distance Z: 500 mm Table dimensions: 1,150 x 490 mm Number of tool positions in the magazine: 22 Gujdpfx Afjyn Nwtjcoa Spindle taper: SK 40 (DIN 69871-A40) Max. spindle speed: 10,000 rpm MACHINE DETAILS Control: HEIDENHAIN TNC 426 Dimensions & Weight Dimensions (L x W x H): 4,500 x 3,500 x 2,700 mm Weight: 4,200 kg Operating Hours Automatic operation: 8,523 h Control on-time: 71,860 h EQUIPMENT Technical documentation Spare parts (as shown in the pictures) Note: Only a 7.5t truck can turn around on the company premises. It is recommended to send a smaller truck for collection.

Condition: ready for operation (used), Year of construction: 1993, functionality: fully functional, machine/vehicle number: 3449, travel distance X-axis: 800 mm, travel distance Y-axis: 410 mm, travel distance Z-axis: 510 mm, workpiece weight (max.): 700 kg, spindle speed (max.): 8,000 rpm, TECHNICAL DETAILS X-axis travel: 800 mm Y-axis travel: 410 mm Z-axis travel: 510 mm Max. workpiece weight: 700 kg Max. spindle speed: 8,000 rpm Spindle taper: ISO 40 MACHINE DETAILS Dimensions & Weight Dimensions (L x W x H): 2,500 x 2,400 x 2,800 mm Total weight: 6,050 kg EQUIPMENT 20-position tool carousel with ISO 40 tool holder Various tool holders Documentation Fanuc CNC control Gedpfx Aeyyi Uksfcsua

Condition: ready for operation (used), Year of construction: 2017, machine/vehicle number: 1000017221, functionality: fully functional, travel distance X-axis: 2,500 mm, travel distance Y-axis: 900 mm, travel distance Z-axis: 60 mm, controller model: BSuite3, number of spindles: 17, TECHNICAL DETAILS Working area X-axis: 2,500 mm Working area Y-axis: 900 mm Working area Z-axis: 60 mm Guodpfsyzpcdox Afcoa Number of axes: 3 Tool: ISO 30 Spindles Total number of spindles: 17 6 vertical in X-axis 5 vertical in Y-axis 4 horizontal in X-axis 2 horizontal in Y-axis MACHINE DETAILS Numerical control: BSolid Software - BSuite3 EQUIPMENT Automatic unloading device Integrated blade for groove insertion Front protective and safety systems with mats Perimetric protective grids External reference: MME002

Condition: ready for operation (used), Year of construction: 2005, operating hours: 1,476 h, functionality: fully functional, travel distance X-axis: 1,050 mm, travel distance Y-axis: 510 mm, travel distance Z-axis: 510 mm, controller model: Mazatrol 640M, spindle speed (max.): 12,000 rpm, TECHNICAL DETAILS Travel X-axis: 1,050 mm Travel Y-axis: 510 mm Gjdoy Am Ndopfx Afcsua Travel Z-axis: 510 mm Spindle speed: 12,000 rpm Tool changer positions: 30 Table size: 1,700 x 750 mm MACHINE DETAILS Spindle motor power: 18.5 kW Control: Mazatrol 640M Weight: 7,100 kg EQUIPMENT Chip conveyor

Condition: excellent (used), Year of construction: 2017, functionality: fully functional, Specification: Gjdpjyzf E Ujfx Afcsua Length of cut: 3100mm Width of Cut Vertical: 2070mm Width of Cut Horizontal: 1958mm Depth of Cut: 60mm Motor Power: 5.3HP Saw Blade Dia: 250mm Saw Blade Bore: 30mm 400V 50Hz

Condition: good (used), Bench Foods 32VCUD 32 tray vertical dehydrator Stainless, adjustable temperature range from 15'c to 90'c plus an ambient air mode, timer controls, stainless mesh trays for even drying on both sides, mobile, 1Ph Gsdpfx Afjyziiwjceua

Condition: used, Year of construction: 2017, (2017) Bridgeport GX480 CNC Vertical Machining Centre with Fanuc Oi-MF Control Guedpfx Afey Angkocsa Table Dimension 600 x 400mm (3 'T' Slots, Dimension 14 x125mm). Maximum Table Load 300kg. Axis Travel 'X'=480mm, 'Y'=400mm, 'Z'=430mm. Spindle Nose To Table Min/Max 150-580mm. Distance From Column To Table Centre 429mm. Rapid Traverse 'X'=36m/min, 'Y'=36m/min, 'Z'=36m/min. Maximum Spindle Speed 10,000rpm (7.5kW Motor). Spindle Taper BT40. 16 Position ATC. Maximum Tool Ø94mm (Ø150mm non Adjacent), Maximum Tool Weight 7kg. Maximum Tool Length 250mm. S/No. NVLB7E0004 (2017). With Coolant System, LCE Transformer & Handwheel. Approx Dimensions W1,800 x D2,445 x H1,940mm. Weight 3,800kg. Note: Workholding/Tooling Not Included.

Condition: excellent (used), Year of construction: 2004, functionality: fully functional, travel distance X-axis: 5,500 mm, travel distance Y-axis: 525 mm, travel distance Z-axis: 380 mm, Model: COMET ISOLA ES381 V06 Year: 2004 Control: ISAC ‘X’ axis Stroke: 5500mm ‘Y’ axis Stroke: 525mm Godpfxsyx Hn So Afcoua ‘Z’ axis Stroke: 380mm Spindle Taper: ISO 40 Spindle Speeds: 24,000 RPM