Used Tos Sus 80 for sale (18,590)

Condition: used, CTS Type: TSS-70/130 Water-cooled cooling unit For sale is a high-quality temperature shock test chamber from CTS (Clima Temperatur Systeme), model TSS-70/130. The device is used for performing temperature shock tests and is typically used in industry, research, and quality assurance. Application areas: Material tests Aging tests Electronics and component tests Temperature shock and cyclic temperature tests Technical data: Type: TSS-70/130 Test volume: 130 liters Temperature range: Hot chamber: +50°C to +200°C Cold chamber: -80°C to +100°C Heating rate: approx. 6 K/min from room temperature to +180°C Cooling rate: approx. 4 K/min from room temperature to -60°C Temperature deviation: ±1 K in time ±2 K spatially Temperature change rate: max. 100 K/min on average for shock test tests without heat input Temperature adjustment rate: ≤ 15 min in the range of -65°C to +200°C with 10 kg of ICs Cycle time: < 10 seconds Electrical data: Connection: 400 V, 3/N, 50 Hz Rated power: approx. 17.2 kW Rated current: approx. 29 A On-site protection: 32 A slow-blow fuse Connection: Cekon 32 Refrigeration system: Refrigerant: R404A / R23 water-cooled, low-noise, fully hermetic Equipment / Features: CTS control panel Microprocessor-controlled control and monitoring system Program operation up to 100 test programs possible digital setpoint and actual value display RS232 interface 2 free switching channels for on-site control of the test specimen Fault message on potential-free contact Load up to 30 V DC, 2 A EMC tested Technical design: Hot and cold chamber Mobile frame with lifting spindle drive Test chamber / mobile frame made of stainless steel, material no. 1.4301 Insert basket made of stainless steel wire Pipe passage NW 50 with sealing plug Compressed air connection 1/4" AG Dodpfx Acjy Hkd Hjyokw Condensate drain non-pressurized R 1/2" internal thread Safety door lock lockable door with window Dimensions according to installation diagram: External dimensions approx.: 2335 x 940 x 1820 mm Loading dimension approx.: 1990 x 940 x 1652 mm Test chamber dimensions: height approx. 410 mm Width approx. 480 mm, depth approx. 660 mm Window: 300 x 300 mm Other data: Protection class: IP 22 Sound pressure level: < 60 dB(A) Weight: approx. 950 kg Average consumption during test cycle: approx. 8 kWh For your safety as a buyer, the following information: The following points are carried out on our offered chambers in advance: 1. Functional check and replacement of necessary components 2. If necessary, refill with legally compliant refrigerant 3. Leak test with certificate 4. After successful inspection, the chambers are subjected to a documented test run. Condition: used Scope of delivery: see pictures (Changes and errors in technical data are subject to change!) We will gladly answer any further questions you may have by telephone.

Condition: new, Year of construction: 2024, SCHORR ride-on sweeper Electric sweeper Street sweeper Floor sweeper Powerful and smooth-running sweeper for indoor and outdoor use. With switchable spray nozzle. The ride-on sweeper offers a convenient and efficient solution for floor cleaning. The ergonomic seat and intuitive controls enable effortless operation, even over long periods of time. The powerful motor ensures thorough cleaning even in demanding conditions. With a generous 80-liter collection container, large areas can be cleaned without frequent interruptions. This combination of convenience and efficiency makes floor cleaning a stress-free and enjoyable task. The LED work lights fitted as standard make it easier to work in darker areas. With an output of 1920 watts from 48V, the sweeper is equipped with enough power to get you comfortably to over 4 hours of continuous use. SCHORR RR80KM ride-on sweeper - Discover the advantages: -- Fully electric ride-on sweeper with 1250mm working width - ideal for large indoor and outdoor areas -- 48V/1920W power -- 80 liter bagless rear collection container, easy to extend and empty -- Powerful system with 48V and 58Ah -- With switchable spray nozzle for less dust turbulence -- Extremely easy to operate -- Outstanding maneuverability Technical data Manufacturer (abbreviation): SCHORR Type designation of the manufacturer: RR80KM Drive: Seat Power: 1920W Operating time: approx. 4 hours Number of wheels: 4 Tires: PU (non-slip) Own weight: 400kg Basic dimensions Collecting tank volume: 80l Fresh water tank volume: 10l Main brush diameter: 500mm Total length: 1600mm Total height: 1300mm Total width: 1250mm Sweeper width (without brush): approx. 80cm *Further technical data available on request. The chassis is made of flexible and robust plastic all round, which reduces potential damage to walls, for example. Apart from the side bristles, nothing protrudes beyond the cladding so that work can be carried out as closely as possible to objects. The collection container is made of sturdy steel and can be easily removed from the rear of the machine. Sensitive components such as the headlights are protected by a metal bumper. Overall, the machine is perfectly equipped for most applications. Of course, we usually have all spare parts in stock and can deliver them quickly if you do have a problem. If you need technical support, we have the necessary technical expertise and can also carry out repairs in our in-house workshop. Would you prefer to finance or lease the appliance? No problem! We also offer you attractive options for this. Simply contact us and we will advise you on the various options. We look forward to hearing from you! Djdpfx Asuac D Uecyskw We at SCHORR will be happy to answer any questions you may have about our ride-on sweeper. You can reach our competent team by phone or email. We look forward to hearing from you and being able to help you with advice.

Condition: used, Technical details: Weight: ca. 80 kg dimension machine xH: ca. 077 x 0,45 x 0,5 m BRUSH MACHINE * Dkodpfxewiu Sme Acyew

Condition: new, ATiB HTUB 80/100-L HF Charger The HTUB is a top-of-the-line HF charger designed for maximum performance. This range encompasses all the key features of HF chargers in terms of efficiency, power factor, ventilation, internal structure (dedicated 3 compartments), and overall flexibility. An integrated digital interface with an OLED display and built-in USB enables the best and easiest monitoring/adjustment of charging parameters, diagnostics, and data reports. Key Features AC input voltage: 480Vac (3-phase) 50-60Hz / 600Vac (3-phase) 50-60Hz Display: OLED/LCD display, 4 LEDs, and 4 control buttons Dksdpexuqrwjfx Acyow Adjustment type: Via OLED display: current, capacity, and 7 pre-set charging profiles Via PC/laptop/USB connection: advanced programming Data storage: Report on the last 50 charging cycles and important technical data (integrated USB connection) Cooling system: Dedicated air cooling directly to the heatsink. Temperature-controlled fan speed. Standby mode within +104°F (+40° C) internal component temperature Efficiency: ≥ 92% Operating temperature: +32° to +104°F (0° to +40° C) Certification: CSA Safety Features Input protection: 3x fast-blow AC fuses Output protection: Ultra-fast fuse (reverse polarity protection) Thermal protection: Sensors on IGBTs, diodes, and power transformer (maximum temperature adjustable) with derating Protection during battery disconnection: Undervoltage safety shutdown (direct battery disconnection) Mechanical Properties Dimensions (L x W x H): 456 x 195 x 570 mm Degree of protection: IP 21 (vertical) – Dedicated air cooling directly to the heatsink. Weight: 28 kg You can find more items – new and used – in our shop! International shipping costs available upon request!

Condition: new, Lammers 16 BG 223-4MA66-Z 225M Electric Motor 45 kW Djdpfx Aceq Tqmzjyokw Manufacturer: Lammers Type: 16 BG 223-4MA66-Z 225M Rated power: 45 kW Speed: 1475 rpm Voltage: 3 x 400/690 V Amperage: 80 A Frequency: 50/60 Hz Protection class: IP55 Weight: 315 kg More items in other sizes – new and used – can be found in our shop! International shipping costs available upon request!

Condition: new, Promess Servo Press KA-EMF80 80 KN, New, with DMS Amplifier Djdpfxsrgn Nne Acyokw Manufacturer: Promess Type: KA-EMF80 Type: Servo Press KN: 80 Condition: New Calibrated: Yes DMS Amplifier: BA 624.u2 More servo presses, new and used, can be found in our shop! International shipping costs available upon request!

Condition: reconditioned (used), functionality: fully functional, Year of construction: 2014, operating hours: 3,266 h, load capacity: 1,400 kg, lifting height: 8,600 mm, free lift: 2,840 mm, load center: 600 mm, fuel type: electric, mast type: triplex, construction height: 3,400 mm, battery capacity: 620 Ah, remaining battery capacity: 80 %, battery voltage: 48 V, fork length: 1,150 mm, tire condition: 90 %, front tire type: polyurethane tires (non-marking), rear tire type: polyurethane tires (non-marking), total height: 3,400 mm, drive type: Elektro, Equipment: 3rd hydraulic function, CE marking, UVV, pallet forks, sideshift, Reach truck Load center: 600 ISO class: ISO Class 2 = 1,000 - 2,500 kg Mast type: Triplex Condition: Refurbished, no warranty Technical condition: very good Front tire type: Vulkollan Front tire condition: 80 - 100% Rear tire type: Vulkollan Rear tire condition: 80 - 100% Battery voltage: 48V Battery capacity: 620Ah Battery manufacturer: 80% remaining capacity Battery type: PzS Battery year of manufacture: 2020 Battery condition: 80 - 100% Description: Overhauled, serviced, and inspected according to FEM 4.004 (UVV) // Completely repaired, serviced, and checked Side shifter Djdpfxexnfgie Acyjkw Mast traverse shift

Condition: used, Max. stamping capacity: 800 kN Max. thrust: 1100 kN Punches 27 mm holes in 20 mm steel Dsdsxf E U Uepfx Acyekw Shears on the flat steel shear to 500 mm up to material thickness of 18 mm steel Further technical data on request With a range of stamps and matrices

Condition: excellent (used), operating hours: 1,108 h, lifting height: 5,450 mm, fuel type: electric, mast type: triplex, total height: 3,210 mm, total length: 6,350 mm, total width: 2,260 mm, color: other, Year of manufacture: 2023 Year of construction: 2023 Empty weight: 16.539 kg Lifting capacity: 8.000 kg CE mark: yes Technical condition: very good Visual appearance: very good = Additional options and accessories = - 3rd hydr. circuit Dedpfsw U U Ahsx Acyskw - 4th Hydr. circuit - Blower - Freelift - Non marking tires - Side shift - Work lamp(s) = Remarks = General Country of production: Germany Condition CE type: CE Kaup forkpositioner and side-shift, Forks 2400 mm, Battery charger, Non marking tyres

Condition: new, pressure 80.0 t stroke 250 mm table surface area 1040 x 260 mm column travel between the guideways 1040 mm ajustment speed 8.0 mm/sec working feed 5.0 mm/sec return speed 10.0 mm/sec engine output 5.5 kW Dksdpfx Aew U U Svscyow weight of the machine ca. 835 kg. dimensions of the machine ca. 1810 x 700 x 2100 mm Equipment: - robust electro-hydraulic workshop press, with fixed cylinder - Ideal for aligning axles, shafts etc., but also for pressing in and pressing out bolts, bearings, bushes etc. - Robust welded steel construction for heavy-duty use - Table height adjustment via piston rod * Including round steel chain and 2x locking bolts * Piston rod with metric mount - 1x set of V-block prism support - Pressure gauge for pressure display - Simple manual operation with : * 1x feed speed * 1x working speed * 1x retraction speed - piston can be stopped in any position - Hydraulic tank permanently mounted on the side - operating instructions

Condition: used, Year of construction: 1977, pressure 80 t stroke 8 - 112 mm no. of strokes 65 /min throat 345 mm passage to the back 500 mm dayligth 472 mm Dodpozrpqmsfx Acyekw table surface area 840 x 610 mm hole in the table 280 / 315 mm table height over floor 800 mm ram surface 650 x 410 mm ram adjustment 71 mm power requirement 13,5 kW Weight 6,10 t dimensions of the machine ca. 1,5 x 1,9 x 3,0 m x m x m with motor with two speeds, pneumatic clutch/brake combination (Ortlinghaus), mechanical overload protection in ram, manual stroke adjustment, motoric ram adjustment, fix table, motoric centralized lubrication, two-hand operation

Condition: ready for operation (used), functionality: fully functional, machine/vehicle number: H2X396Y00749, Year of construction: 2021, operating hours: 15,230 h, load capacity: 8,000 kg, lifting height: 7,000 mm, fuel type: gas, mast type: duplex, TECHNICAL DETAILS Lifting height: 7,000 mm Clearance height: 4,220 mm Lifting capacity: 8,000 kg MACHINE DETAILS Mast type: Duplex Djdpfxszxcd Te Acyjkw Drive: LPG Engine manufacturer: Linde Inspection valid until: 09/2026 Dimensions & Weight Dimensions (L x W x H): 3,450 x 2,230 x 4,100 mm Unladen weight: 13,050 kg Transport packages: 1 Operating hours: 15,230 h EQUIPMENT 3rd and 4th hydraulic valve for the fork carriage Joystick Heater License plate Full cab Work lights Documentation CE marking

Condition: used, axle configuration: 3 axles, first registration: 08/1995, color: other, Year of construction: 1995 Empty weight: 5.600 kg Axle 1: left 3 mm right 5 mm Axle 2: left 4 mm right 4 mm Axle 3: left 5 mm right 5 mm Djdjzw Evpopfx Acyskw We have the possibility to stack trailers!

Condition: used, Year of construction: 1993, Used 3 meter CNC press brake by Safan Model: CNCL 80 3100 Capacity: 3100 x 80 tons Dedey Nydzepfx Acyekw Y1, Y2, and X axes CNC controlled CNC crowning Flat pressure table Year of manufacture: 1993

Condition: good (used), Year of construction: 2001, functionality: fully functional, FMB MBZ 75 - 80, 5-axis FMB multi-machining center, Type MBZ - 2 / 72-80 / 5, Year of manufacture 2001, PC control with TFT color display, Travel range X/Y/Z 7000/1000/370 mm, Milling head with high-frequency spindle for aluminum, Spindle speed up to 18,000 rpm - 7.5 KW, Tool changer, 12-position, Tool holder HSK 40, 2-axis NC dovetail milling head, 8 pneumatic clamping elements, Swivel machining possible, Program generator, FMB programming software, Pneumatic material stop, Dodpfx Aozhuitecyokw Measuring / probing device.

Condition: good (used), Year of construction: 2004, Well-maintained, used press brake from Ermaksan. Type: AP 2600 80 Capacity: 2600 x 80 tons Dodsz Aihmopfx Acyskw NC control Includes a set of tooling.

Condition: used, Weiss Type: SB2/500/80 Dodpfx Acozd Ultsyjkw Water-cooled climate testing chamber Cold-heat operation: -75°C ... +180°C Climate operation: +10...+95°C Humidity range: 10...98 % RH Temperature stability, over time: ± 0.2K Humidity stability: ±1 % RH Temperature change rate: Cooling: approx. 1.4 K/min Heating: approx. 2.5 K/min External dimensions: Height 1980 mm, Width 1265 mm, Depth 1365 mm Connections: Left side: ∅ 100 mm Right side: ∅ 50 mm The connection voltage is: 400V/3Ph+N+PE/50 Hz Power: 10.4 kVA Weight: approx. 720 kg Refrigerant: R404a / R23 For your security as a buyer, please note the following information! The following points are carried out on our offered chambers in advance: 1. Functional check and replacement of necessary components 2. If necessary, new filling with legally compliant refrigerant 3. Leak test with certificate 4. After successful inspection, the chambers are subjected to a documented test run. Condition: used Scope of delivery: (See picture) (Changes and errors in the technical data are subject to change!) We will gladly answer any further questions you may have by phone.

Condition: used, 80 DIN-rail power supplies Manufacturer: Mean Well Djdpjzu A Tasfx Acyokw Type: DRH-120-24 Condition: Good used condition. Fully functional prior to removal. Accessories, tools, and clamping devices shown are included in the scope of delivery only if specified in the additional information. Subject to technical changes, errors, and prior sale.

Condition: excellent (used), Year of construction: 2020, Ref: 11147 . 2020 Horizon HT-80 Three-Knife Trimmer Fully automatic three-knife trimmer designed for short-to-medium-run and digital/book-of-one production. Can work offline or inline with Horizon binders up to 1,000 cycles/hour, 51 mm book thickness, automatic setup and book-of-one capability Features: Automatic size setup via colour touchscreen: input the untrimmed and finished book dimensions and the machine automatically positions the relevant sections. Servo-controlled jogging and clamping provide accurate registration, while the swing-knife cutting action is designed to give a clean three-side trim. Also capable of book-of-one production. Books of the same finished size but different thicknesses can be processed consecutively It can run inline with Horizon BQ-470, SB-07 and SB-09S systems, as well as offline. Djdsz Akmkjpfx Acyokw Specification: Untrimmed book size – Max. 330 × 330 mm Untrimmed book size – Min. 145 × 105 mm Finished book size – Max. 300 × 300 mm Finished book size – Min. 139 × 99 mm Book / trim thickness: 1–51 mm Maximum head & foot trim: 30 mm each Maximum fore-edge trim: 30 mm Production speed: 400–1,000 cycles/hour Clamping pressure: 4–8 kN, up to 10 kN depending on conditions Clamp drive: Servo motor Standard formats: A4, A5, 8.5 × 11", 5.5 × 8.5" Job memory: 200 jobs Dimensions: 1,610 × 2,610 × 1,515 mm W × D × H Power: 3-phase, 200–230 V, 50/60 Hz; 380/400/415 V versions via transformer

Condition: used, Year of construction: 2001, Technical details: grinding length: 2500 mm grinding width: 800 mm workpiece height: 800 mm Table movement horizontal: Längshub: 2700 mm Table movement horizontal: Querhub: 800 mm table speed: längs: 1 - 35 / quer: 0 - 3 m/min feed: vertical: 0,001 / quer: 0,0025 mm/Hub magnetic plate size: 2500 x 800 mm Automatic grinding wheel feed: 0,001 mm distance table - spindle center: 900 mm Dksdpfx Acovbgr Rsyow grinding spindle speed: k.A. U/min dimensions of grinding wheel: 400 x 76 x 127 mm total power requirement: 36 kW weight of the machine ca.: 13,5 t dimension machine xH: 7,5 x 2,8 x 2,7 m dimension coolant device LxWxH: 1,8 x 1,0 x 0,92 m dimensions of hydaulic: 1900 x 800 x 1500 mm transport measurements machine: L: 8,0 x B: 2,4 x H: 2,85 m The machine is currently in the technical department. technical features: -Hydraulic unit -dressing device *

Condition: used, Year of construction: 2005, x-travel 880 mm Dkedpfx Ajvn Ur Eecyew y-travel 630 mm z-travel 630 mm control iTNC 530 Heidenhain turning speed range - main spindle max. 18.000 min/-1 power capacity - main spindel 28 / 19 kW max. Torque 121 / 82 Nm tool taper HSK-A 63 swivellable B: +30° / -120 ° table surface area Ø 700 / 1.250 x 700 mm max. table load 650 kg rotatable C: 360 ° max. workpiecediameter 850 mm max. workpiece height 550 mm number of toolpositions 32 pos. tool taper HSK-A 63 max. tool diameter 80 mm max. tool-dia with free toolbox 160 mm max. tool weight 8,0 kg change-time chip to chip 10 sec feed speeds max. 30.000 mm/min rapid traverse 30 m/min Accelaration 5 m/s² total power requirement 48 kVA weight of the machine ca. 14,0 t dimensions of the machine ca. 6,5 x 5,0 x 2,9 m 5 Axis CNC - MachiningCenter Universal DECKEL MAHO - DMU 80 monoBLOCK - NC-Rotary Table (C-Achse) integrated in rigid-table - Swivel-Milling-Head (B-Axis) - only 6.100h Spindle Hours

Condition: good (used), Year of construction: 2004, Item: DP-18231-Pump-APV-W80-80-240 Brand: APV-SPX Type: W+80/80 240 Brand: APV-SPX Dksdotk Hykjpfx Acyew Serial number: 3013986 Year: 2004

Condition: new, width 800 mm depth 380 mm height 1800 mm Dedpfx Acju Immlsyskw weight 70 Kg Cabinet with 4 shelves. Maximum load per shelf 40 kg. Color code 7035. Weight 75kg.

Condition: good (used), Complete used Tiflex textile screen printing setup for sale: a full manual screen printing line, ready to print t-shirts, sweatshirts, hoodies, polo shirts and garments with plastisol inks. This Tiflex screen printing equipment covers every step of the process: multi-colour printing on a 6-colour manual press, intermediate flash curing between colours, then final curing in an infrared conveyor dryer. A practical solution for textile decorators, garment printers, print shops, apparel brands and new screen printing workshops. 1. TIFLEX 2368000LC MANUAL SCREEN PRINTING PRESS (6 COLOUR, 6 STATION CAROUSEL) - Rotary manual press, 6 printheads and 6 stations - Maximum print area: 40 x 50 cm - Maximum outer screen frame size: 60 x 80 cm - Micro-registration with 3 knobs (X, Y and rotation) for accurate colour registration - Off-contact adjustment, screen/pallet parallelism and front/back pallet adjustment - Sliding pallets locked by ball plunger, rear screen clamping with anti-crush system - Pallet height: 86 cm, net weight: 200 kg - Fully manual, no electrical connection needed, dismantles for transport 2. 16 PALLETS INCLUDED (PLATENS) - 6 x men's XL pallets: 66 x 48 cm - 6 x women's M pallets: 50 x 32 cm - 2 x children's S pallets: 40 x 22 cm - 1 x sleeve pallet: 60 x 15 cm - 1 x sleeve pallet: 40 x 15 cm A complete pallet set for adult, youth and sleeve printing, with enough pallets to run all 6 stations in men's or women's sizes. 3. TIFLEX 40 x 40 CM INFRARED FLASH CURE UNIT (2008, VERY GOOD CONDITION) - Flash dryer for screen printing, 6 short-wave infrared emitters, 12 kW - Drying area: 40 x 40 cm - Drying timer and air-jet cooling timer - Automatic cycle start by contact rod when the pallet is detected - Half-power setting for delicate mesh - Height-adjustable stand on wheels - Three-phase 400 V, 18 A - Ideal for flashing a white underbase on dark garments before printing bright colours 4. TIFLEX T-IR 80 INFRARED CONVEYOR DRYER (2008, GOOD CONDITION) - Infrared textile dryer / drying tunnel for curing plastisol inks - Useful belt width: 80 cm, length under heating element: 130 cm - Teflon glass conveyor belt resistant to 250 °C - Variable belt speed, temperature controller with digital display - Movable shutters for thick items up to 12 cm (caps) - Fume extraction outlet, diameter 125 mm - Power: 4.8 kW, three-phase 400 V, 7 A - Overall dimensions: 270 x 131 x 130 cm, net weight: 265 kg Dksdps Agvmmofx Acysw LOCATION AND SHIPPING Equipment located in Bègles (Bordeaux area), France. Shipping across Europe and worldwide available on quotation. Tiflex screen printing machine, manual screen printing press, screen printing carousel, 6 colour 6 station press, textile screen printing equipment, t-shirt printing machine, garment printing, flash dryer, flash cure unit, infrared conveyor dryer, plastisol curing, screen printing pallets, used screen printing equipment.

Condition: like new (used), Year of construction: 2012, If you have any questions or require further information, please do not hesitate to send us a message or call us. Djdpfe Ahmzvsx Acyekw