Used Thread Coiler for sale (2,595)

Condition: used, CTS Type: TSS-70/130 Water-cooled cooling unit For sale is a high-quality temperature shock test chamber from CTS (Clima Temperatur Systeme), model TSS-70/130. The device is used for performing temperature shock tests and is typically used in industry, research, and quality assurance. Application areas: Material tests Aging tests Electronics and component tests Temperature shock and cyclic temperature tests Technical data: Type: TSS-70/130 Test volume: 130 liters Temperature range: Hot chamber: +50°C to +200°C Cold chamber: -80°C to +100°C Heating rate: approx. 6 K/min from room temperature to +180°C Cooling rate: approx. 4 K/min from room temperature to -60°C Temperature deviation: ±1 K in time ±2 K spatially Temperature change rate: max. 100 K/min on average for shock test tests without heat input Temperature adjustment rate: ≤ 15 min in the range of -65°C to +200°C Ndodpfjy Hkd Hjx Abysc with 10 kg of ICs Cycle time: < 10 seconds Electrical data: Connection: 400 V, 3/N, 50 Hz Rated power: approx. 17.2 kW Rated current: approx. 29 A On-site protection: 32 A slow-blow fuse Connection: Cekon 32 Refrigeration system: Refrigerant: R404A / R23 water-cooled, low-noise, fully hermetic Equipment / Features: CTS control panel Microprocessor-controlled control and monitoring system Program operation up to 100 test programs possible digital setpoint and actual value display RS232 interface 2 free switching channels for on-site control of the test specimen Fault message on potential-free contact Load up to 30 V DC, 2 A EMC tested Technical design: Hot and cold chamber Mobile frame with lifting spindle drive Test chamber / mobile frame made of stainless steel, material no. 1.4301 Insert basket made of stainless steel wire Pipe passage NW 50 with sealing plug Compressed air connection 1/4" AG Condensate drain non-pressurized R 1/2" internal thread Safety door lock lockable door with window Dimensions according to installation diagram: External dimensions approx.: 2335 x 940 x 1820 mm Loading dimension approx.: 1990 x 940 x 1652 mm Test chamber dimensions: height approx. 410 mm Width approx. 480 mm, depth approx. 660 mm Window: 300 x 300 mm Other data: Protection class: IP 22 Sound pressure level: < 60 dB(A) Weight: approx. 950 kg Average consumption during test cycle: approx. 8 kWh For your safety as a buyer, the following information: The following points are carried out on our offered chambers in advance: 1. Functional check and replacement of necessary components 2. If necessary, refill with legally compliant refrigerant 3. Leak test with certificate 4. After successful inspection, the chambers are subjected to a documented test run. Condition: used Scope of delivery: see pictures (Changes and errors in technical data are subject to change!) We will gladly answer any further questions you may have by telephone.

Condition: used, Year of construction: 2015, turning diameter max. 500 mm turning length 800 mm control sl Operate 3G ShopTurn Siemens swing diameter 500 mm distance between spindles 1.020 mm turning speed range - main spindle max. 5.000 min/-1 power capacity - main spindel 25 / 34 kW max. Torque 280 / 380 Nm spindle head 170h5 spindle diameter in front bearing 130 mm spindle bore 87 mm C-Axis 0,001 ° tool taper HSK 63 A number of toolpositions 80 pos. max. tool diameter 80 mm max. tool-dia with free toolbox 120 mm max. tool weight 12 kg max. tool length 300 mm Speed Milling Spindle max. 12.000 min/-1 power capacity - milling spindle 19 / 22 kW Torque 85 / 100 Nm tool taper HSK 63 A B-Axis +/- 110 ° x-axis -10 ... +490 mm y-axis +/- 100 mm z-axis 1: 845 mm z-axis 2: 600 mm z-axis 3: 800 mm Spindle speed range subspindle max. 6.000 min/-1 power capacity - Sub spindle 20 / 27 kW bar material dia. 51 mm spindle bore diameter 73 mm spindle diameter in front bearing 100 mm C-Axis 0,001 ° total power requirement 85 kVA weight of the machine ca. 10,0 t dimensions of the machine ca. 7,0 x 2,9 x 2,6 m CNC - Turning- and Millingcenter DMG MORI - CTX beta 800 TC V6 - 5-axis simultaneous machining - Main and counter-spindle - Swivel-type milling spindle - ShopTurn - Off-center turning and milling - Multi-thread cycle Ndsdpfjz S Nygex Abyoc - Program state control - Tool sorting cycle - Easy Tool Monitor for Siemens control system - Chuck flushing system for main spindle - Chuck flushing system for counter-spindle - Differential pressure clamping - Coolant supply through the counter-spindle - Bar machining package for CTX beta (77 mm capacity) Workpiece the-take-off device (left side) Hydraulic hollow clamping system 4-color signal tower Interface for bar feeder or bar magazine - In-process workpiece measuring system (Renishaw) - Safety window cleaning system - Coolant spray gun

Condition: good (used), Machines pictures 1 to 9 Gillardon price 9500,-€ Technical data: - Drilling capacity into solid steel ST 60 32 mm - Drilling capacity GG 25 40 mm - Thread cutting ST 60 M 27 - Drill spindle holder MK 4 - Quill stroke 150 mm - 12 drill spindle speeds 102 - 2000 rpm - 3 drilling feeds 0.1 - 0.3 mm - min. / max. distance spindle - table 310 / 610 mm - Drilling radius min / max 400 / 1200 mm - Table height 720 mm - Table size 1200 x 500 mm Ndjdpfxju Nm Nio Abyjc - Drive 400 V / 1.6 / 2.9 kW - Space requirement approx. W 1200 x H 2800 x D 2300 mm - Weight approx. 1500 kg - with: - Thread cutting device - hydr. columns + boom clamping - Coolant device - Vertical T-slots on the rear side of the machine Machine 2 pictures 10 to 15 HKS 34 MT Price 16.500,-€ Drilling capacity 45mm Table size : 1200 x 560 mm drilling capacity 45mm Spindle holder MK 4 quill stroke 170mm Speed / steps 70-2000 rpm Feed rate / steps 0.1 0.2 0.3mm/rev Motor 2.9 KW

Condition: excellent (used), Voest DA 180 Voest Alpine DA 180 Conventional Lathe with Digital Readout, Year of Manufacture 1981, in Very Good Original Condition The machine comes from the training workshop of a renowned German mechanical engineering company. Technical Data: VOEST ALPINE Lathe Lead and feed screw lathe, Type DA 180/1, Year of Manufacture 1981 Swing over bed: 380 mm Swing over cross slide: 185 mm Turning length: 1,000 mm Centre height: 180 mm Bed width: 330 mm Spindle bore: 52 mm Tailstock taper: MK 4 Coolant system Motor: 380 Volt, 5.5 kW 12 spindle speeds: 44 - 2,000 rpm 66 longitudinal feeds: 0.072 - 4.038 mm/rev 66 cross feeds: 0.036 - 2.019 mm/rev 66 metric threads: 0.5 - 28 mm 66 inch threads: 1 - 32 TPI Njdpfx Aexp I D Tjbyjdc 66 module threads: 0.25 - 14 66 DP threads: 2 - 112 3-jaw chuck Weight approx. 1,200 kg Accessories and Equipment: 1 piece Röhm 3-jaw chuck 200 mm Multifix size B Digital readout About the Machine: We offer a Voest Alpine DA 180 conventional lathe with digital readout, year of manufacture 1981, in very good condition. The machine is, of course, fully functional. All slides run very smoothly and evenly. The Voest also runs very quietly, even at high speeds. This newer generation of lathes is very operator-friendly and can produce grind-finish-quality surfaces. Take the opportunity to inspect this machine under power at our premises and see its condition for yourself. You can find further drilling machines from reputable manufacturers on our website.

Condition: good (used), Year of construction: 2000, Donau Danuflex 145 Donau Danuflex 145 high-speed radial drilling machine, year of manufacture 2000, in SUPER condition CE compliant!! Technical data: Nedpfxoz Rwpye Abyjdc Year of manufacture: 2000 Drilling and threading capabilities Drilling capacity in steel: approx. 42 to 45 mm Threading: up to M36 Tool holder / spindle: MK 4 Spindle speed: 15 to 2,800 rpm (infinitely variable) [1, 2, 3] Travel distances & work area Outrigger travel: 1,050 mm Drilling radius: min. 540 mm / max. 1,590 mm Quill stroke: approx. 200 to 220 mm Column stroke (W-axis): approx. 450 mm Column diameter: 195 mm Table & dimensions Work table: typically approx. 1,200 x 750 mm with 5 T-slots Work table height: approx. 905 mm (ergonomic design for standing operation) Feed: automatic / stepless quill feed with electromagnetic feed clutch Equipment (standard): Threading device, hydraulic clamping for outrigger and lifting column, central lubrication and machine light Accessories and equipment: Several work tables About the machine: Offered is a Donau Danuflex 145 high-speed radial drilling machine. This high-speed radial drilling machine is in very good original condition. It comes from a company where it was only used for training purposes. It has a very easy-to-use control system. Up to 3 fixed machining stations ensure maximum flexibility in the machining of workpieces, both large and small, as well as very long parts. Swivel tables allow the machining of angled bores. Large travel distances and workpiece heights up to 1500 mm are ensured. Effortless, simultaneous positioning to a drilling position in 3 axes. A self-centering spindle head positions itself precisely in centering bores. Concentric countersinking is achieved by self-centering countersinks in the bore. The guides are regularly lubricated by the central lubrication system. The Donau has been mechanically and electrically tested by us. Take the opportunity to inspect and try out the Donau on site under power. You can find more drilling machines from well-known manufacturers on our website.

Condition: good (used), Year of construction: 2000, functionality: fully functional, drilling capacity: 40 mm, quill stroke: 200 mm, quill diameter: 80 mm, Machine Version • Work table 1200 x 600 mm with 4T-slots • Ram travel 750 mm • Drilling spindle SK 40 with tool clamping device • Stepless speed programming • Stepless quill feed via three-phase servo motor • 2 T-slots 18 mm on the machine base at the rear • 2 T-slots 18 mm on the machine base on the left • Thread cutting device • Central lubrication • Coolant system • Machine lamp • CE marking • Protective device • USB interface Dimensions and travels Tool holder SK 40 Column diameter mm 195 Table dimensions mm 1800 x 600 Number of T-slots 4 Distance between T-slots mm 125 Quill stroke (Z-axis) mm 200 Column stroke (W-axis) mm 410 Distance Spindle bottom edge - min mm 70 Njdpoz S T A Eefx Abyodc Table top edge max. mm 680 Distance Spindle bottom edge - min mm 970 Ground max. mm 1580 Drilling radius mm 540 - 1590 Work table height mm 900 Machining values Drilling capacity in steel St 60  40 Cast iron GG 22  50 Thread cutting Steel St 60 M 36 Cast iron GG 22 M 42 Main spindle drive AC motor, frequency-controlled kW 5.5 at 100 % duty cycle Speed range: min -1 15 - 2800 Torque Nm max. 250 constant from min -1 15 – 2000 Feed drives X-axis - AC - Servo motor kW 0.25 Y-axis - AC - Servo motor kW 0.25 Z-axis - AC - Servo motor kW 4.50 W-axis - AC - Servo motor kW 2.50 Rapid traverse speeds (X/Y/Z): m/min 7.5 / 7.5 / 5 Rapid traverse speeds (W): m/min 3 Feed rates, stepless mm/min 5 – 2000 Accuracy Positioning accuracy X, Y axis on 1200 mm mm ± 0.075 Electrical data Operating voltage / frequency V / Hz 400 / 50 Control voltage V 24 Hydraulic unit for clamping kW 0.75 Total connected load kVA 13.0 Weight Danumeric 440 (without packaging) with table 1800 x 600 mm kg 2800 CNC control Axes: 4 (X, Y, Z, W), expandable Processor: 32-bit CPU Screen: TFT flat screen backlit, easily readable from all sides, 215 x 160 mm Position data: Cartesian or polar, dimensions absolute or incremental, Unit: mm or inch or in degrees Interpolation: 2 axes (X, Y) Technology database: Tool management, tool suggestions according to Machining type, material-dependent cutting data suggestions Tool management: max. 500 tools Subprogram technique: yes Machining cycles Standard software options: Programming in dialog, 38 zero point offsets, rotation and mirroring, teach-in for X, Y, Z, restart in program with selection functions for targeted start Zero point determination: Cycles to determine zero points by manually probing the workpiece for: - any clamped rectangular parts - any clamped round parts - aligning castings and forged parts - Angle detection in round parts by probing reference edges or surfaces Test graphic Graphical display of drilling patterns

Condition: refurbished (used), Year of construction: 1991, Work table 750 mm x 1200 mm Outrigger travel distance 1000 mm Tool holder MK 4 Ndedpfjz S Tzzox Abyjc Drilling capacity 32 mm in steel Threading device Coolant system Documentation

Condition: used, Year of construction: 1979, No minimum price – guaranteed sale to the highest bidder! Loading: December 1st to December 10th. TECHNICAL DETAILS Working area Swinging diameter over bed: 480 mm Swinging diameter over cross slide: 200 mm Nedpfx Abj Aa Naujysdc Turning length: 650 mm Maximum turning diameter over bed cover: 200 mm Distance between centers: 750 mm Spindle Spindle head: Size 6 Spindle bore: 58 mm Control CNC path control: 2 axes Control system: Siemens SINUMERIK 5T Threading: available Motor control cabinet: Siemens 810T Tailstock Taper in tailstock quill: MK 4 Tailstock quill travel: max. 200 mm Tailstock travel: 550 mm Performance data Total power requirement: 18 kW Machine weight: approx. 2.7 t Machine dimensions Space requirement: approx. 2.70 × 1.58 × 1.68 m Control cabinet Control cabinet dimensions: 800 × 400 × 2,300 mm Control cabinet weight: 150 kg Motor control cabinet dimensions: 800 × 900 × 1,000 mm Motor control cabinet weight: 200 kg EQUIPMENT 4 chucks Spax screws Sheet metal screwdriver Drill Drill bits

Condition: used, Year of construction: 2019, Used machine Year of manufacture: 2019 Video available at: Base machine - Dynestic 7535-R Automatic 12.7 Dynestic table For classic nesting machining with wear plate Machining length: 3700 mm Working direction: from right to left Machine frame in welded construction with ground and hardened prism guides for the traversing carriage, aggregate head and consoles Traversing carriage in gantry design Rack and pinion drive, helical, in X and Y direction, Ball screw spindles Z-axis for precise positioning Technical data: Machining dimensions: Max. load on nesting table X = 3700 mm Y = 2200 mm Max. travel distances X = 5295 mm Y = 2935 mm Z = 565 mm Max. clearance height DYNESTIC table Z = 250 mm from the top of the table (without wear plate) Maximum programmable speed Vector speed: 128.0 m/min X = 80 m/min, Y = 100 m/min, Z = 25 m/min 4-stage extraction hood with pneumatic height adjustment and viewing window Voltage 400 V, 50/60 Hz CONTROL: Dual-core processor Operating system: Windows XP 80 GB hard drive / 1 GB RAM RJ45 network connection 10/100 Base-T Fast Ethernet US keyboard and Microsoft IntelliEye mouse (optical) CD-ROM / CD-RW drive (CD burner) Remote maintenance Integrated network card for data transmission of control and program data. Data transmission via high-speed internet connection Requirement: High-speed internet connection to the machine. DYNESTIC table Solid, continuous machining table with grid spacing, continuous grooves in X and Y direction, Groove spacing: 50 mm with 25 meters of sealing cord for securing the wear plate 1 machining field with stop strips / stop Height: 30 mm, pneumatically lowerable 2 stop strips in Y direction and 1 stop in X direction on the right (when viewed from the front of the machine) Vacuum fields 1-circuit vacuum system Drilling unit 7881-R, 24 spindles Drive power 3.0 kW, incl. saw unit Nedpfx Abezt Twyoyedc 18 vertical spindles individually selectable Arrangement in L-shape, 11+2 in X and 6 in Y direction 32 mm grid Max. drill diameter: 35 mm Total drill length: 70 mm from the mounting end (depending on plate thickness) Spindle extension stroke: 70 mm Rotation direction: alternating clockwise / counterclockwise n(max.) 1000 - 5710 min-1, infinitely variable Mount: M 10 thread - clearance fit 11 mm without tool, without mount 6 horizontal spindles 2 twin drill spindles in X direction (distance 32 mm between 1st and 2nd horizontal drill spindle) 1 twin drill spindle in Y direction Mount: M 10 thread, clearance fit 11 mm Total drill length max. 70 mm from the mounting end without tool, without mount Pressure booster, increases the standard pressure from 6 to 8 bar 5-axis milling unit 7844, Power: 10.0 kW (S6) cardanic, C-axis rotatable +/- 360°, A-axis rotatable +/- 180° n(max.) = 0 - 24000 min-1, infinitely variable, max. power at 12000 min-1 to 24000 min-1 Liquid cooling (cooling unit included) with HSK-F 63 tool holder with right-hand thread (for right-hand cutting tools) with collet chuck with HSK shank Ceramic ball bearings (hybrid bearings) Tool weight max. 6 kg (incl. holder) Tools:

Condition: used, Year of construction: 1999, Machine number: 9114108 Weight (approx.): 150 kg Nodpfszd Hntjx Abysdc Motor power: 0.71 / 1.26 kW Overhang – stand to drilling center: 600 mm Max. material height: 200 mm Table width: 1000 mm Number of drilling spindles: 4 Drill chuck: Screw-in thread Drilling depth limitation: Yes Drilling stroke: 70 mm Speeds: 1400 / 2800 rpm Workpiece clamp: Yes Drilling feed: Hand lever Working height or feed table height: 890 mm, with lighting Storage location: Nattheim

Condition: ready for operation (used), Decoiler with 1 to x 380-460 mm width, coil-inside-diam. 340 - 440 mm, outside-diam. 1100 mm under power Nedpsuviffjfx Abysdc

Condition: like new (used), Year of construction: 2022, functionality: fully functional, EURO-Jabelmann bagging scale, model TN 260, with bulk material hopper 1,500 × 1,500 mm – year of manufacture 2022 – like new, including accessories For sale is a practically new bagging scale, model TN 260, from EURO-Jabelmann (manufacturer in Itterbeck, Made in Germany), with an upstream bulk material hopper 1,500 × 1,500 mm, manufactured in 2022. The scale doses and fills bulk materials such as potatoes, onions, vegetables, or firewood directly from the storage hopper into bags. Condition: – Like new, hardly used – Fully functional – Inspection and test run possible by arrangement Included in the scope of delivery: – Bagging scale, model TN 260, with bulk material hopper 1,500 × 1,500 mm Njdez Tda Ropfx Abyodc – “Gantry” for hand sewing machine with roller track, roller device, and aluminum spring tensioner (load capacity 4–6 kg) – new price €825 net – 2× hand sewing machine Union Special 4000A (bag sewing machine, single-thread chain stitch, with thread chain separator, 90 W) – new price €1,425 each net New price of the scale without accessories: €18,950 net. New price of the entire package: €22,625 net. Price: €10,000 net plus VAT (11,900 € gross) for the complete package, negotiable – VAT can be shown separately. Collection & shipping: – Location: 31848 Bad Münder am Deister – Loading will be assisted – Shipping by freight forwarder possible for an extra charge

Year of construction: 2011, operating hours: 10,500 h, condition: used, machine/vehicle number: ISP17, Used Inspector KRONES Linatronic K735 year 2011 The Used Inspector KRONES Linatronic K735 year 2011 offers a proven and efficient solution for quality control in high-performance bottling lines. The German manufacturer KRONES, a global leader in beverage industry automation, built this model with reliability, precision, and modular construction in mind. As a result, this inspector fits seamlessly into industrial environments that demand high accuracy and operational consistency. Electrical characteristics and technical configuration of the Used Inspector KRONES The Used Inspector KRONES Linatronic K735 year 2011 runs on a three-phase power supply at 400/230 volts, with a 50 Hz frequency and a 13-ampere current draw. Consequently, it aligns with European industrial standards and supports stable operation under demanding conditions. Furthermore, the electrical system includes integrated safety devices that protect the components from overload or malfunction. In addition, the compact and durable enclosure facilitates easy integration into existing production layouts. Year of production and machine hours KRONES produced this unit in 2011. Since then, the machine has logged 10,500 operating hours, which reflects moderate usage for equipment designed for industrial use. Compared to other models with similar functionality, this unit maintains good performance standards. Moreover, the machine structure shows minimal wear, confirming its careful maintenance. Therefore, technicians can expect reliable functionality without immediate need for major refurbishment. The machine is currently operational, specifically until Easter. Then it will be dismantled.  Supported inspection types The Used Inspector KRONES Linatronic K735 year 2011 is equipped with a comprehensive range of inspection functions to ensure the quality and integrity of each bottle. -The system performs bottom inspection to detect chips, cracks, or foreign objects at the base. -The sidewall (walls) inspection uses a rotating mirror and cameras to identify defects such as scratches, cracks, or dirt on the entire lateral surface. -The neck finish and thread inspection ensures that bottle openings are free from damage or deformation that could compromise sealing or capping. Ndodpj Adyv Uofx Abyoc -Scuffing inspection checks for surface abrasions that indicate excessive wear. In addition, the machine employs infrared (IR) and high-frequency (HF) technology to detect residual liquid, ensuring the bottles are dry and ready for fill...

Condition: used, Universal   Shaker angle adapters / adapter devices   Universal shaker accessories Heavy-duty aluminum angle adapters, clamping devices, and adapter elements for vibration testing systems, vibration tests, and special applications   For sale is a used accessory set for an electrodynamic shaker or vibration testing system.   The set consists of various heavy-duty aluminum angle adapters, adapter plates, clamping devices, clamping blocks, and other accessories. Ideal for test specimen mounting, special designs, and vibration tests.   Technical data:   Manufacturer: unknown Type: Accessory set for electrodynamic shaker / vibration testing system Ndsdpfxjzpx Ucj Abyec Material: predominantly aluminum Design: angle adapters, adapter plates, clamping devices, and fasteners   Components: Several heavy-duty angle adapters Adapter plates of various sizes Clamping and tightening devices Clamping blocks and adapter elements Fastening materials and other accessories as shown in the pictures   Features:   Heavy-duty aluminum construction Threaded and clearance holes Universally applicable Angle adapters for test specimen mounting Adapter plates Clamping and tightening devices Accessories as shown in the pictures   Application areas:   Electrodynamic shakers Vibration testing systems Vibration testing Material testing Environmental simulation Research and development Automotive industry Test specimen mounting and special designs   Scope of supply:   Complete accessory set as shown in the pictures Angle adapters Adapter plates Clamping devices Clamping blocks Fastening materials Other accessories as shown in the pictures   Weight: 600 kg   Condition:   Used Visual condition as shown in the pictures. Normal signs of wear and tear, scratches, and pressure marks are present.   Only the accessories shown in the pictures are sold.   The table shown in the pictures or other items not explicitly mentioned are not included in the sale.   Shipping on a pallet or collection is possible. Subject to changes, errors, and prior sale.   We will be happy to answer any further questions by telephone.

Condition: good (used), Year of construction: 2004, functionality: fully functional, The used FANUC ALFA 1-iC wire EDM is a medium-sized, 5-axis CNC-controlled electrical discharge machine with submerged machining; X/Y/Z travel: 550/370/410 mm; year of manufacture: 2004, CE-compliant, complete with automatic wire threading, chiller, and openable roof. Technical specifications of the FANUC ROBOCUT ALPHA 1iC wire EDM: - Maximum workpiece dimensions (L x W x H): 820 x 730 x 300 mm - Maximum workpiece weight: 1000 kg - CNC control: Fanuc Series 180is-WB - 5 axes (X, Y, Z, U, V) - Stroke on axes X/Y/Z/U/V: 550/370/410/120/120 mm - Rapid traverse on X, Y, Z axes: 900 mm/min - Rapid traverse on U, V axes: 450 mm/min - Worktable size (L x W): 780 x 600 mm - Maximum cutting angle: 30 degrees - Automatic wire threading - Wire diameter: 0.1–0.3 mm - Electrical supply: 400 V; 50/60 Hz - Total power requirement: 13 kW Nodpfexd R Hmex Abysdc - Total machine weight: 3100 kg

Condition: used, Year of construction: 1995, turning diameter 570 mm turning length 2000 mm control num + CNC Keller Nodoyrhm Uspfx Abyodc centre height 280 mm turning dia. over face-slide 365 mm spindle bore 62 mm spindle turning speed range 3 - 2500 U/min spindle head DIN 55 027 Gr. 8 cutting speed Konstant 1 - 9999 m/min feed in x - axis 0,01 - 50 mm/U feed range Z-direction 0,01 - 50 mm/U rapid travel - longitudinal/face 10 / 5 m/min feed power x-Achse 7100 N feed power z-Achse 12.500 N travel of cross-slide 345 mm upper slide travel 125 mm bed width 360 mm tailstock quill diameter 80 mm tailstock quill stroke 190 mm tailstock taper MT 5 max. workpiece weight -without tailstock 400 kg max. workpiece weight between centres 1000 kg max.workpiece weight:each extra steadyrest 300 kg threading metric 0,1 - 400 mm/Stg. dimensions of machine L x W x H 3,98 x 1,87 x 1,81 m Accessories: 3-jaw chuck RÖHM, 250 mmø; MULTIFIX-toolpost, solid steady, coolant

Year of construction: 2023, condition: used, Used Machine Year of Manufacture: 2023 Features and Technical Specifications: - Stationary, oil-lubricated 2-cylinder piston compressor - Two-stage compression - V-belt drive - Intercooler and aftercooler Ndodpfxozy Dzis Abysc - Condor pressure switch - Motor protection and safety valve - Tank pressure gauge - Check valve and relief valve - Condensate drain valve - Additional connection fittings with blind plugs - Rubber vibration dampers - Manhole opening for tank inspection - Tank compliant with AD-2000 regulations - Suction capacity: 660 l/min - Effective flow rate: 520 l/min - Maximum operating pressure: 10 bar - Motor power: 4.0 kW / 5.5 PS - Power connection: 400 V / 50 Hz - Start type: Direct start - Speed: 1,025 rpm - Vertical, internally coated 270-liter compressed air tank - Air outlet: 3/4-inch female thread with shut-off valve - Sound pressure level: 78 dB(A) - Dimensions: 750 × 705 × 1,800 mm - Weight: approx. 170 kg

Condition: used, GRIESER Type: GFD 11 LST Product: Grieser Laboratory Stand Dissolver Intended Use: The machine is used for mixing powdery solids, liquids, and pastes, as well as for incorporating fillers. The viscosity range can range from thin to pasty. Machine Design: The laboratory stand dissolver consists essentially of the machine stand, the lifting device, the drive for the mixing tool, the telescopic hood with spring pressure, the collet chuck, and the control cabinet (non-Ex) with control and compact controller. Nedezdtflepfx Abyodc In the working position, the container (customer-supplied) and the telescopic hood form a closed mixing chamber. A hose connection is provided on the hood, which serves according to the intended use. The drive of the mixing tool is equipped with a speed control via a frequency inverter. The arrangement, power, and speeds of the motors can be found in the attached project drawing. The speed of the mixing tool, the mixing time/remaining mixing time, mixing sequences, and other functions can be displayed on the display of the compact controller. Operation Switching on and off is done via corresponding buttons in the control cabinet. Lifting the mixing tool drive Lifting is carried out by switching on the lifting motor. This runs only as long as the push buttons (two-hand safety circuit UP-UP) are pressed. After releasing the buttons, the arm remains in any desired position. Lowering the mixing tool drive To lower the arm, the corresponding buttons (two-hand safety circuit DOWN-DOWN) on the control panel are pressed. Mixing tool change The mixing tool shaft is provided with an M8 connection thread. Depending on the requirement, the mixing tool (stirring blade, customer-supplied) can be unscrewed and replaced. Technical data: Machine type: GFD 11 LST Year of construction: 2017 Operating voltage: 400 V Frequency: 50 Hz Control voltage: 24 V DC Mixing tool speed: 25 – 500 min-1 via frequency inverter Ambient temperature: +5°C to +40°C Protection class: IP 54 Container: 1.18 liters, D=100, H=150 (75) customer-supplied Mixing tool: Stirring blade, customer-supplied Control panel / display The machine is operated primarily via the compact PLC controller "Vision 560-T25B". Safety-relevant functions such as disconnection from the mains via the main switch, shutdown in case of danger by pressing the emergency stop button, and the two-hand operation for opening or closing the mixing chamber are excluded. The control panel consists of an illuminated LCD display and film-covered tactile buttons. The buttons marked with a letter have fixed functions assigned to them. These can be activated at any time, independently of the menu. As soon as a function has been activated, the corresponding status appears in the upper right area of the screen in the "Operating Display" menu. The individual menu screens can be switched through using the up and down buttons. Condition: used Scope of delivery: (See picture) (Changes and errors in the technical data and information are subject to change!) We will be happy to answer any further questions you may have by telephone.

Year of construction: 1982, condition: used, Offered for sale is a conventional center lathe with lead screw and feed rod. Distance between centers: 3000mm. Swing over bed: 710mm. Center height: 342mm. Spindle speed range: 8-1250rpm. Number of spindle speed steps: 23. Longitudinal feed: 0.056-10mm/rev. Cross feed: 0.028-5mm/rev. Metric thread pitches: 1-176mm. Max. workpiece weight between centers: 2500kg. Max. workpiece weight between centers with steady rest: 3000kg. Tailstock quill travel: 300mm. Equipped with digital readout, three-jaw chuck, four-way tool post and tailstock. Weight: approx. 5400kg. Overall dimensions X/Y/Z: approx. 5325mm/1510mm/1510mm. Inspection possible by arrangement. Nedpfo Ad Nq Iox Abyjdc

Condition: used, Trumpf Type: TC 6000 L 1300 Laser and punching machine Technical data: Ndedszd Ulaopfx Abyec Power supply: 400V/50 Hz Fuse rating: 3 x 100 A Connected power: 65 kVA Working area X x Y without repositioning: Combined operation: 2585 x 1280 mm Punching operation: 2585 x 1370 mm Laser operation: 2585 x 1280 mm Performance: Laser: 2000 W Maximum sheet thickness: 8 mm Maximum punching force (including 20 kN holding-down device): 220 kN Active holding-down device (programmable in stages): 4.5-20 kN Maximum workpiece weight: 200 kg Maximum clearance height: In punching operation: 35 mm In laser operation: 22 mm Speeds: X-axis: 90 m/min Y-axis: 60 m/min Simultaneous movement: Punching: 900 min Marking: 2800 min C-axis: Punching: 60 revolutions/min Thread forming: 330 revolutions/min Tools: Tool stations on linear magazine: 19 with 2 grippers Number of tools when using a multi-tool: 19 to 190 tools Rotation of all tools: 360° Tool change time: 1.5-5 s Maximum punching diameter: Single stroke: 76.2 mm on all tool stations Standard multi-cut: 200 mm Maximum bending height: 25 mm Maximum part size: 500 x 500 mm Accuracy: Positioning deviation: ± 0.1 mm Average position spread: ± 0.03 mm TRUMPF CNC control: Base: Siemens SINUMERIK 840D Loading and dismantling must be handled by the buyer! Condition: used Scope of delivery: (See picture) (Changes and errors in the technical data are subject to change!) We will be happy to answer any further questions you may have by telephone.

Condition: used, RMS Vibration exciter / vibration testing system RMS SW 6005 Vibration exciter sold exclusively as a source of spare parts A used vibration exciter from RMS Regelungs- und Messtechnik is for sale. The device is explicitly sold solely as a source of spare parts. Its functionality has not been tested. Operational readiness or completeness is not guaranteed. Technical data: Manufacturer: RMS Regelungs- und Messtechnik Designation: Vibration exciter Type: SW 6005 Some of the technical specifications on the nameplate are damaged and not completely clearly legible. Equipment: RMS vibration exciter SW 6005 Mounting plate with threaded holes Lateral pneumatic suspension elements Lifting/lowering device Control and connection housing Transport/lifting eyes Base frame Existing mounting and supply components Accessories as shown in the pictures Application areas: Ndjdoz Iqh Aepfx Abyoc Spare parts sourcing Repair of existing vibration testing systems Supply of replacement and assembly components Reconstruction and repair projects Scope of delivery: 1 × RMS SW 6005 vibration exciter Existing mounting and supply components Accessories as shown in the pictures Weight: approx. 700 kg Condition: Used Visual condition as shown in the pictures Signs of wear and tear due to age and use Functionality not tested Sold exclusively as a source of spare parts. The device is explicitly not offered as a functional machine. No warranty for functionality, operational readiness, or completeness. Shipping or freight shipping is possible. Subject to changes, errors, and prior sale. We are happy to answer any further questions by telephone.

Condition: used, RMS   Vibration exciter / Vibration testing system   RMS SW 6005 Vibration exciter, sold exclusively as a source of spare parts   For sale is a used vibration exciter from RMS Regelungs- und Messtechnik.   The device is sold explicitly and solely as a source of spare parts. Its functionality has not been tested. Operational readiness or completeness is not guaranteed.   Technical data:   Manufacturer: RMS Regelungs- und Messtechnik Designation: Vibration exciter Type: SW 6005 Year of manufacture: 1983   Voltage: 30 V Current: 200 A Force: 11,770 N Vibration amplitude: ± 13 mm Velocity: 1.2 m/s Acceleration: 100 g   Weight: approx. 700 kg (estimated)   Equipment:   RMS vibration exciter SW 6005 Mounting surface with threaded holes Pneumatic vibration isolation Lateral spring elements Pneumatic components Control and connection housing Cooling/air connection with hose Transport/lifting eyes Solid base frame Existing mounting and supply components Accessories as shown in the pictures   Application areas:   Spare parts sourcing Maintenance of existing vibration testing systems Ndodpfxoz Iqigo Abyjc Spare parts and assembly supply Rebuilding and repair projects   Scope of supply:   1 × RMS SW 6005 vibration exciter Existing mounting and supply components Cooling/air hose as shown in the pictures Accessories as shown in the pictures   Condition:   Used Optical condition as shown in the pictures Signs of wear and tear due to age and use Functionality not tested   Sold exclusively as a source of spare parts. The device is explicitly not offered as a functional machine. No guarantee for functionality, operational readiness, or completeness.   Shipping or freight shipping possible. Subject to changes, errors, and prior sale.   We will gladly answer any further questions by telephone.

Condition: used, Year of construction: 1984, bore capacity in steel (diameter) 32 mm arm length 1230 mm bore stroke 180 mm total power requirement 3 kW weight of the machine ca. 1,8 t dimensions of the machine ca. 2,2 x 1,8 x2,3 m High-speed radial drilling machines with: - Feed mechanism - Thread-cutting attachment Ndjde Aa A E Rjpfx Abyoc

Condition: new, GMN TSE 240 cg - SP: 3000-3600-4000-5000 RPM / 37 grinding spindle, shaft diameter: 130mm, front overhang at the thread: 102mm, including test report and installation instructions, new condition: €25,000, unused, 100% functional, scope of supply as shown in the photos. Nodpei D U Trefx Abyedc ATTENTION: Please request the costs for packaging and shipping separately!

Condition: new, functionality: fully functional, Year of construction: 2025, laser power: 60 W, laser wavelength: 1,070 nm, type of cooling: air, warranty duration: 12 months, shaft length: 1,070 mm, Equipment: cabin, Laser engraving machine with 60-watt laser power (new) - 60-watt MOPA laser (enables color laser engraving on stainless steel) - incl. 4th axis (rotary unit) - incl. Windows 10 Pro 64-bit PC system - incl. 22" monitor - everything fully installed and calibrated - Engraving software in German - very easy to operate - switch on and start - Fiber laser source with 60 watts for high-contrast and fast markings with extremely high resolution (see images) - Deep engraving up to 4mm possible (also in hardened steel) - Wobble function, e.g., for cleaning metal components - for engraving on many metals (stainless steel, brass, aluminum, etc.) and many plastics - heavy-duty industrial quality - Complete system / ready for immediate use - Working area approx. 500 x 600 x 600mm (l x w x h) - Clamping surface with fastening threads in a 50mm grid - LED work area lighting - 50mm pipe connection for fume extraction - Engraving area approx. 180 x 180mm - expandable to approx. 300 x 300mm - incl. foot switch to start the engraving process Please also note our attractive leasing/hire-purchase offers. Sales are exclusively to commercial businesses. Delivery / Consulting / Sales only in Germany / Austria / Switzerland Machine dimensions approx.: Width: 800mm Height: 1800mm Depth: 1000mm Njdpjfkgq Njfx Abyjdc Weight: approx. 150kg