Used Thread Clip for sale (2,682)

Condition: excellent (used), Year of construction: 1984, Maximum turning height 180 mm Distance between centers 1000 mm Swinging diameter over bed 350 mm Swinging diameter over cross slide 200 mm Bed width 255 mm Spindle bore 36.5 mm Spindle mounting, DIN 55027 Size 5 Speed range, 14 steps 28 – 2500 rpm Feeds, 9 longitudinal 0.04 – 0.4 mm/rev ditto, 9 facing 0.02 – 0.2 mm/rev 38 metric threads 0.2 – 18 mm 35 Whitworth threads 76 – 2“ 31 module threads 0.4 – 13.5 module 25 diametral pitch threads 36 – 2.6 pitch Tailstock mounting MK 4 Drive power 3 kW Machine dimensions L x W x H 2380 x 850 x 1800 mm Weight 1300 kg Accessories / Special features: • 2-axis digital display EASSON ES-8A • Quick-change tool holder system “Multifix” Size B • Chuck guard, foldable, electrically secured • Coolant system Siegfried Volz Werkzeugmaschinen Rüschebrinkstr. 151-153 Pgedpfx Akoyud Iteieu DE - 44143 Dortmund - Wambel / Germany

Condition: used, CTS Type: TSS-70/130 Water-cooled cooling unit For sale is a high-quality temperature shock test chamber from CTS (Clima Temperatur Systeme), model TSS-70/130. The device is used for performing temperature shock tests and is typically used in industry, research, and quality assurance. Application areas: Material tests Aging tests Electronics and component tests Temperature shock and cyclic temperature tests Technical data: Type: TSS-70/130 Test volume: 130 liters Temperature range: Hot chamber: +50°C to +200°C Cold chamber: -80°C to +100°C Heating rate: approx. 6 K/min from room temperature to +180°C Cooling rate: approx. 4 K/min from room temperature to -60°C Temperature deviation: ±1 K in time ±2 K spatially Temperature change rate: max. 100 K/min on average for shock test tests without heat input Temperature adjustment rate: ≤ 15 min in the range of -65°C to +200°C with 10 kg of ICs Cycle time: < 10 seconds Electrical data: Connection: 400 V, 3/N, 50 Hz Rated power: approx. 17.2 kW Rated current: approx. 29 A On-site protection: 32 A slow-blow fuse Connection: Cekon 32 Refrigeration system: Refrigerant: R404A / R23 water-cooled, low-noise, fully hermetic Equipment / Features: CTS control panel Microprocessor-controlled control and monitoring system Program operation up to 100 test programs possible digital setpoint and actual value display RS232 interface 2 free switching channels for on-site control of the test specimen Fault message on potential-free contact Load up to 30 V DC, 2 A EMC tested Technical design: Hot and cold chamber Mobile frame with lifting spindle drive Test chamber / mobile frame made of stainless steel, material no. 1.4301 Insert basket made of stainless steel wire Pipe passage NW 50 with sealing plug Compressed air connection 1/4" AG Condensate drain non-pressurized R 1/2" internal thread Psdpfoy Hkd Hsx Akisgu Safety door lock lockable door with window Dimensions according to installation diagram: External dimensions approx.: 2335 x 940 x 1820 mm Loading dimension approx.: 1990 x 940 x 1652 mm Test chamber dimensions: height approx. 410 mm Width approx. 480 mm, depth approx. 660 mm Window: 300 x 300 mm Other data: Protection class: IP 22 Sound pressure level: < 60 dB(A) Weight: approx. 950 kg Average consumption during test cycle: approx. 8 kWh For your safety as a buyer, the following information: The following points are carried out on our offered chambers in advance: 1. Functional check and replacement of necessary components 2. If necessary, refill with legally compliant refrigerant 3. Leak test with certificate 4. After successful inspection, the chambers are subjected to a documented test run. Condition: used Scope of delivery: see pictures (Changes and errors in technical data are subject to change!) We will gladly answer any further questions you may have by telephone.

Condition: used, Year of construction: 2015, turning diameter max. 500 mm turning length 800 mm control sl Operate 3G ShopTurn Siemens swing diameter 500 mm distance between spindles 1.020 mm turning speed range - main spindle max. 5.000 min/-1 power capacity - main spindel 25 / 34 kW max. Torque 280 / 380 Nm spindle head 170h5 spindle diameter in front bearing 130 mm spindle bore 87 mm C-Axis 0,001 ° tool taper HSK 63 A number of toolpositions 80 pos. max. tool diameter 80 mm max. tool-dia with free toolbox 120 mm max. tool weight 12 kg max. tool length 300 mm Speed Milling Spindle max. 12.000 min/-1 power capacity - milling spindle 19 / 22 kW Torque 85 / 100 Nm tool taper HSK 63 A B-Axis +/- 110 ° x-axis -10 ... +490 mm y-axis +/- 100 mm z-axis 1: 845 mm z-axis 2: 600 mm z-axis 3: 800 mm Spindle speed range subspindle max. 6.000 min/-1 power capacity - Sub spindle 20 / 27 kW bar material dia. 51 mm spindle bore diameter 73 mm spindle diameter in front bearing 100 mm C-Axis 0,001 ° total power requirement 85 kVA weight of the machine ca. 10,0 t dimensions of the machine ca. 7,0 x 2,9 x 2,6 m CNC - Turning- and Millingcenter DMG MORI - CTX beta 800 TC V6 - 5-axis simultaneous machining - Main and counter-spindle - Swivel-type milling spindle - ShopTurn - Off-center turning and milling - Multi-thread cycle - Program state control - Tool sorting cycle - Easy Tool Monitor for Siemens control system - Chuck flushing system for main spindle - Chuck flushing system for counter-spindle - Differential pressure clamping - Coolant supply through the counter-spindle - Bar machining package for CTX beta (77 mm capacity) Workpiece the-take-off device (left side) Hydraulic hollow clamping system 4-color signal tower Interface for bar feeder or bar magazine - In-process workpiece measuring system (Renishaw) - Safety window cleaning system - Coolant spray gun Psdpfx Akjz S Nygjiogu

Condition: good (used), Machines pictures 1 to 9 Gillardon price 9500,-€ Technical data: - Drilling capacity into solid steel ST 60 32 mm - Drilling capacity GG 25 40 mm - Thread cutting ST 60 M 27 - Drill spindle holder MK 4 - Quill stroke 150 mm - 12 drill spindle speeds 102 - 2000 rpm - 3 drilling feeds 0.1 - 0.3 mm - min. / max. distance spindle - table 310 / 610 mm - Drilling radius min / max 400 / 1200 mm - Table height 720 mm - Table size 1200 x 500 mm - Drive 400 V / 1.6 / 2.9 kW - Space requirement approx. W 1200 x H 2800 x D 2300 mm - Weight approx. 1500 kg - with: - Thread cutting device Pgjdpfxeu Nm Nie Akiju - hydr. columns + boom clamping - Coolant device - Vertical T-slots on the rear side of the machine Machine 2 pictures 10 to 15 HKS 34 MT Price 16.500,-€ Drilling capacity 45mm Table size : 1200 x 560 mm drilling capacity 45mm Spindle holder MK 4 quill stroke 170mm Speed / steps 70-2000 rpm Feed rate / steps 0.1 0.2 0.3mm/rev Motor 2.9 KW

Condition: excellent (used), Voest DA 180 Voest Alpine DA 180 Conventional Lathe with Digital Readout, Year of Manufacture 1981, in Very Good Original Condition The machine comes from the training workshop of a renowned German mechanical engineering company. Technical Data: VOEST ALPINE Lathe Lead and feed screw lathe, Type DA 180/1, Year of Manufacture 1981 Swing over bed: 380 mm Swing over cross slide: 185 mm Turning length: 1,000 mm Centre height: 180 mm Bed width: 330 mm Spindle bore: 52 mm Tailstock taper: MK 4 Coolant system Motor: 380 Volt, 5.5 kW 12 spindle speeds: 44 - 2,000 rpm 66 longitudinal feeds: 0.072 - 4.038 mm/rev 66 cross feeds: 0.036 - 2.019 mm/rev 66 metric threads: 0.5 - 28 mm 66 inch threads: 1 - 32 TPI 66 module threads: 0.25 - 14 66 DP threads: 2 - 112 3-jaw chuck Weight approx. 1,200 kg Pgedpfx Aksxp I D Toisu Accessories and Equipment: 1 piece Röhm 3-jaw chuck 200 mm Multifix size B Digital readout About the Machine: We offer a Voest Alpine DA 180 conventional lathe with digital readout, year of manufacture 1981, in very good condition. The machine is, of course, fully functional. All slides run very smoothly and evenly. The Voest also runs very quietly, even at high speeds. This newer generation of lathes is very operator-friendly and can produce grind-finish-quality surfaces. Take the opportunity to inspect this machine under power at our premises and see its condition for yourself. You can find further drilling machines from reputable manufacturers on our website.

Condition: used, Year of construction: 1979, No minimum price – guaranteed sale to the highest bidder! Loading: December 1st to December 10th. TECHNICAL DETAILS Working area Swinging diameter over bed: 480 mm Swinging diameter over cross slide: 200 mm Turning length: 650 mm Maximum turning diameter over bed cover: 200 mm Distance between centers: 750 mm Spindle Spindle head: Size 6 Spindle bore: 58 mm Control CNC path control: 2 axes Control system: Siemens SINUMERIK 5T Threading: available Motor control cabinet: Siemens 810T Tailstock Taper in tailstock quill: MK 4 Tailstock quill travel: max. 200 mm Tailstock travel: 550 mm Performance data Total power requirement: 18 kW Machine weight: approx. 2.7 t Pede Aa Naujpfx Akiogu Machine dimensions Space requirement: approx. 2.70 × 1.58 × 1.68 m Control cabinet Control cabinet dimensions: 800 × 400 × 2,300 mm Control cabinet weight: 150 kg Motor control cabinet dimensions: 800 × 900 × 1,000 mm Motor control cabinet weight: 200 kg EQUIPMENT 4 chucks Spax screws Sheet metal screwdriver Drill Drill bits

Condition: used, Year of construction: 2019, Used machine Year of manufacture: 2019 Video available at: Base machine - Dynestic 7535-R Automatic 12.7 Dynestic table For classic nesting machining with wear plate Machining length: 3700 mm Working direction: from right to left Machine frame in welded construction with ground and hardened prism guides for the traversing carriage, aggregate head and consoles Traversing carriage in gantry design Rack and pinion drive, helical, in X and Y direction, Ball screw spindles Z-axis for precise positioning Technical data: Machining dimensions: Max. load on nesting table X = 3700 mm Y = 2200 mm Max. travel distances X = 5295 mm Y = 2935 mm Z = 565 mm Max. clearance height DYNESTIC table Z = 250 mm from the top of the table (without wear plate) Maximum programmable speed Vector speed: 128.0 m/min X = 80 m/min, Y = 100 m/min, Z = 25 m/min 4-stage extraction hood with pneumatic height adjustment and viewing window Voltage 400 V, 50/60 Hz CONTROL: Dual-core processor Operating system: Windows XP 80 GB hard drive / 1 GB RAM RJ45 network connection 10/100 Base-T Fast Ethernet US keyboard and Microsoft IntelliEye mouse (optical) CD-ROM / CD-RW drive (CD burner) Remote maintenance Integrated network card for data transmission of control and program data. Data transmission via high-speed internet connection Requirement: High-speed internet connection to the machine. DYNESTIC table Solid, continuous machining table with grid spacing, continuous grooves in X and Y direction, Groove spacing: 50 mm with 25 meters of sealing cord for securing the wear plate 1 machining field with stop strips / stop Height: 30 mm, pneumatically lowerable 2 stop strips in Y direction and 1 stop in X direction on the right (when viewed from the front of the machine) Vacuum fields 1-circuit vacuum system Drilling unit 7881-R, 24 spindles Drive power 3.0 kW, incl. saw unit 18 vertical spindles individually selectable Arrangement in L-shape, 11+2 in X and 6 in Y direction 32 mm grid Max. drill diameter: 35 mm Total drill length: 70 mm from the mounting end (depending on plate thickness) Spindle extension stroke: 70 mm Rotation direction: alternating clockwise / counterclockwise n(max.) 1000 - 5710 min-1, infinitely variable Mount: M 10 thread - clearance fit 11 mm without tool, without mount 6 horizontal spindles 2 twin drill spindles in X direction (distance 32 mm between 1st and 2nd horizontal drill spindle) 1 twin drill spindle in Y direction Mount: M 10 thread, clearance fit 11 mm Total drill length max. 70 mm from the mounting end without tool, without mount Pressure booster, increases the standard pressure from 6 to 8 bar 5-axis milling unit 7844, Power: 10.0 kW (S6) Pgsdszt Twyspfx Akiou cardanic, C-axis rotatable +/- 360°, A-axis rotatable +/- 180° n(max.) = 0 - 24000 min-1, infinitely variable, max. power at 12000 min-1 to 24000 min-1 Liquid cooling (cooling unit included) with HSK-F 63 tool holder with right-hand thread (for right-hand cutting tools) with collet chuck with HSK shank Ceramic ball bearings (hybrid bearings) Tool weight max. 6 kg (incl. holder) Tools:

Condition: new, Year of construction: 2024, bore capacity in steel (diameter) 32 mm throat 245 mm Pgsdowlvk Nopfx Akiou bore stroke 135 mm spindle taper MT 3 table-size 410 x 380 mm spindle turning speed range 10 - 2.100 U/min voltage 400 V total power requirement 1,1 kW weight of the machine ca. 210 kg dimensions of the machine ca. 0,7 x 1,8 x 1,75 m - Threading device - Machine vice 150 mm - Drill cassette 9-piece 14.5 mm - 30 mm, MK 2 / MK 3 - Cutting oil spray

Condition: new, Year of construction: 2024, bore capacity in steel (diameter) 35 mm throat 320 mm bore stroke 150 mm spindle taper MT 4 table-size 500 x 400 mm spindle turning speed range 75 - 3.010 U/min feed range - boring 0,1 / 0,15 / 0,22 / 0,33 mm/U quill stroke 150 mm voltage 400 V total power requirement 1,8 kW Pgjdpfx Ajwlvlajkieu weight of the machine ca. 275 kg dimensions of the machine ca. 0,70 x 1,00 x 1,95 m - Serial-No.: 138050673 - Electromagnetic feed - Threading device - Machine vice 150 mm - Two clamping screws 14 mm - 9-piece drill cartridge 14.5 mm - 30 mm, MK 2 / MK 3 - Cutting oil spray

Condition: used, Year of construction: 1984, bore capacity in steel (diameter) 32 mm arm length 1230 mm bore stroke 180 mm total power requirement 3 kW weight of the machine ca. 1,8 t dimensions of the machine ca. 2,2 x 1,8 x2,3 m Podpfj Aa A E Rsx Akiegu High-speed radial drilling machines with: - Feed mechanism - Thread-cutting attachment

Condition: new, GMN TSE 240 cg - SP: 3000-3600-4000-5000 RPM / 37 grinding spindle, shaft diameter: 130mm, front overhang at the thread: 102mm, including test report and installation instructions, new condition: €25,000, unused, 100% functional, scope of supply as shown in the photos. Pjdpfxsi D U Trj Akiogu ATTENTION: Please request the costs for packaging and shipping separately!

Condition: used, Year of construction: 1995, turning diameter 570 mm turning length 2000 mm control num + CNC Keller centre height 280 mm turning dia. over face-slide 365 mm spindle bore 62 mm spindle turning speed range 3 - 2500 U/min spindle head DIN 55 027 Gr. 8 cutting speed Konstant 1 - 9999 m/min feed in x - axis 0,01 - 50 mm/U feed range Z-direction 0,01 - 50 mm/U rapid travel - longitudinal/face 10 / 5 m/min feed power x-Achse 7100 N Psdpfjyrhm Ujx Akiegu feed power z-Achse 12.500 N travel of cross-slide 345 mm upper slide travel 125 mm bed width 360 mm tailstock quill diameter 80 mm tailstock quill stroke 190 mm tailstock taper MT 5 max. workpiece weight -without tailstock 400 kg max. workpiece weight between centres 1000 kg max.workpiece weight:each extra steadyrest 300 kg threading metric 0,1 - 400 mm/Stg. dimensions of machine L x W x H 3,98 x 1,87 x 1,81 m Accessories: 3-jaw chuck RÖHM, 250 mmø; MULTIFIX-toolpost, solid steady, coolant

Year of construction: 2023, condition: used, Used Machine Year of Manufacture: 2023 Features and Technical Specifications: - Stationary, oil-lubricated 2-cylinder piston compressor - Two-stage compression - V-belt drive - Intercooler and aftercooler - Condor pressure switch - Motor protection and safety valve Pgedpfx Aszy Dziskieu - Tank pressure gauge - Check valve and relief valve - Condensate drain valve - Additional connection fittings with blind plugs - Rubber vibration dampers - Manhole opening for tank inspection - Tank compliant with AD-2000 regulations - Suction capacity: 660 l/min - Effective flow rate: 520 l/min - Maximum operating pressure: 10 bar - Motor power: 4.0 kW / 5.5 PS - Power connection: 400 V / 50 Hz - Start type: Direct start - Speed: 1,025 rpm - Vertical, internally coated 270-liter compressed air tank - Air outlet: 3/4-inch female thread with shut-off valve - Sound pressure level: 78 dB(A) - Dimensions: 750 × 705 × 1,800 mm - Weight: approx. 170 kg

Condition: used, Universal   Shaker angle adapters / adapter devices   Universal shaker accessories Heavy-duty aluminum angle adapters, clamping devices, and adapter elements for vibration testing systems, vibration tests, and special applications   For sale is a used accessory set for an electrodynamic shaker or vibration testing system.   The set consists of various heavy-duty aluminum angle adapters, adapter plates, clamping devices, clamping blocks, and other accessories. Ideal for test specimen mounting, special designs, and vibration tests.   Technical data:   Manufacturer: unknown Type: Accessory set for electrodynamic shaker / vibration testing system Material: predominantly aluminum Design: angle adapters, adapter plates, clamping devices, and fasteners   Components: Several heavy-duty angle adapters Adapter plates of various sizes Clamping and tightening devices Clamping blocks and adapter elements Fastening materials and other accessories as shown in the pictures   Features:   Heavy-duty aluminum construction Threaded and clearance holes Universally applicable Angle adapters for test specimen mounting Adapter plates Podpfx Aezpx Ucekisgu Clamping and tightening devices Accessories as shown in the pictures   Application areas:   Electrodynamic shakers Vibration testing systems Vibration testing Material testing Environmental simulation Research and development Automotive industry Test specimen mounting and special designs   Scope of supply:   Complete accessory set as shown in the pictures Angle adapters Adapter plates Clamping devices Clamping blocks Fastening materials Other accessories as shown in the pictures   Weight: 600 kg   Condition:   Used Visual condition as shown in the pictures. Normal signs of wear and tear, scratches, and pressure marks are present.   Only the accessories shown in the pictures are sold.   The table shown in the pictures or other items not explicitly mentioned are not included in the sale.   Shipping on a pallet or collection is possible. Subject to changes, errors, and prior sale.   We will be happy to answer any further questions by telephone.

Condition: used, GRIESER Type: GFD 11 LST Product: Grieser Laboratory Stand Dissolver Intended Use: The machine is used for mixing powdery solids, liquids, and pastes, as well as for incorporating fillers. The viscosity range can range from thin to pasty. Machine Design: The laboratory stand dissolver consists essentially of the machine stand, the lifting device, the drive for the mixing tool, the telescopic hood with spring pressure, the collet chuck, and the control cabinet (non-Ex) with control and compact controller. In the working position, the container (customer-supplied) and the telescopic hood form a closed mixing chamber. A hose connection is provided on the hood, which serves according to the intended use. The drive of the mixing tool is equipped with a speed control via a frequency inverter. The arrangement, power, and speeds of the motors can be found in the attached project drawing. The speed of the mixing tool, the mixing time/remaining mixing time, mixing sequences, and other functions can be displayed on the display of the compact controller. Operation Switching on and off is done via corresponding buttons in the control cabinet. Lifting the mixing tool drive Lifting is carried out by switching on the lifting motor. This runs only as long as the push buttons (two-hand safety circuit UP-UP) are pressed. After releasing the buttons, the arm remains in any desired position. Lowering the mixing tool drive Pgodpfjzdtfljx Akiou To lower the arm, the corresponding buttons (two-hand safety circuit DOWN-DOWN) on the control panel are pressed. Mixing tool change The mixing tool shaft is provided with an M8 connection thread. Depending on the requirement, the mixing tool (stirring blade, customer-supplied) can be unscrewed and replaced. Technical data: Machine type: GFD 11 LST Year of construction: 2017 Operating voltage: 400 V Frequency: 50 Hz Control voltage: 24 V DC Mixing tool speed: 25 – 500 min-1 via frequency inverter Ambient temperature: +5°C to +40°C Protection class: IP 54 Container: 1.18 liters, D=100, H=150 (75) customer-supplied Mixing tool: Stirring blade, customer-supplied Control panel / display The machine is operated primarily via the compact PLC controller "Vision 560-T25B". Safety-relevant functions such as disconnection from the mains via the main switch, shutdown in case of danger by pressing the emergency stop button, and the two-hand operation for opening or closing the mixing chamber are excluded. The control panel consists of an illuminated LCD display and film-covered tactile buttons. The buttons marked with a letter have fixed functions assigned to them. These can be activated at any time, independently of the menu. As soon as a function has been activated, the corresponding status appears in the upper right area of the screen in the "Operating Display" menu. The individual menu screens can be switched through using the up and down buttons. Condition: used Scope of delivery: (See picture) (Changes and errors in the technical data and information are subject to change!) We will be happy to answer any further questions you may have by telephone.

Condition: used, Trumpf Type: TC 6000 L 1300 Laser and punching machine Technical data: Power supply: 400V/50 Hz Fuse rating: 3 x 100 A Connected power: 65 kVA Working area X x Y without repositioning: Combined operation: 2585 x 1280 mm Punching operation: 2585 x 1370 mm Laser operation: 2585 x 1280 mm Performance: Laser: 2000 W Maximum sheet thickness: 8 mm Maximum punching force (including 20 kN holding-down device): 220 kN Active holding-down device (programmable in stages): 4.5-20 kN Maximum workpiece weight: 200 kg Maximum clearance height: In punching operation: 35 mm In laser operation: 22 mm Speeds: X-axis: 90 m/min Y-axis: 60 m/min Simultaneous movement: Punching: 900 min Marking: 2800 min C-axis: Punching: 60 revolutions/min Thread forming: 330 revolutions/min Tools: Tool stations on linear magazine: 19 with 2 grippers Number of tools when using a multi-tool: 19 to 190 tools Rotation of all tools: 360° Tool change time: 1.5-5 s Maximum punching diameter: Pgjdjzd Ulajpfx Akiju Single stroke: 76.2 mm on all tool stations Standard multi-cut: 200 mm Maximum bending height: 25 mm Maximum part size: 500 x 500 mm Accuracy: Positioning deviation: ± 0.1 mm Average position spread: ± 0.03 mm TRUMPF CNC control: Base: Siemens SINUMERIK 840D Loading and dismantling must be handled by the buyer! Condition: used Scope of delivery: (See picture) (Changes and errors in the technical data are subject to change!) We will be happy to answer any further questions you may have by telephone.

Condition: used, RMS Vibration exciter / vibration testing system RMS SW 6005 Vibration exciter sold exclusively as a source of spare parts A used vibration exciter from RMS Regelungs- und Messtechnik is for sale. The device is explicitly sold solely as a source of spare parts. Its functionality has not been tested. Operational readiness or completeness is not guaranteed. Technical data: Manufacturer: RMS Regelungs- und Messtechnik Designation: Vibration exciter Type: SW 6005 Some of the technical specifications on the nameplate are damaged and not completely clearly legible. Equipment: RMS vibration exciter SW 6005 Mounting plate with threaded holes Lateral pneumatic suspension elements Lifting/lowering device Control and connection housing Transport/lifting eyes Base frame Existing mounting and supply components Accessories as shown in the pictures Application areas: Spare parts sourcing Repair of existing vibration testing systems Supply of replacement and assembly components Reconstruction and repair projects Scope of delivery: 1 × RMS SW 6005 vibration exciter Existing mounting and supply components Accessories as shown in the pictures Weight: approx. 700 kg Condition: Used Visual condition as shown in the pictures Signs of wear and tear due to age and use Functionality not tested Sold exclusively as a source of spare parts. The device is explicitly not offered as a functional machine. Podpfx Aoz Iqh Askisgu No warranty for functionality, operational readiness, or completeness. Shipping or freight shipping is possible. Subject to changes, errors, and prior sale. We are happy to answer any further questions by telephone.

Condition: used, RMS   Vibration exciter / Vibration testing system   RMS SW 6005 Vibration exciter, sold exclusively as a source of spare parts   For sale is a used vibration exciter from RMS Regelungs- und Messtechnik.   The device is sold explicitly and solely as a source of spare parts. Its functionality has not been tested. Operational readiness or completeness is not guaranteed.   Technical data:   Manufacturer: RMS Regelungs- und Messtechnik Designation: Vibration exciter Type: SW 6005 Year of manufacture: 1983   Voltage: 30 V Current: 200 A Force: 11,770 N Vibration amplitude: ± 13 mm Velocity: 1.2 m/s Acceleration: 100 g   Weight: approx. 700 kg (estimated)   Equipment:   RMS vibration exciter SW 6005 Pjdpsz Iqigofx Akiegu Mounting surface with threaded holes Pneumatic vibration isolation Lateral spring elements Pneumatic components Control and connection housing Cooling/air connection with hose Transport/lifting eyes Solid base frame Existing mounting and supply components Accessories as shown in the pictures   Application areas:   Spare parts sourcing Maintenance of existing vibration testing systems Spare parts and assembly supply Rebuilding and repair projects   Scope of supply:   1 × RMS SW 6005 vibration exciter Existing mounting and supply components Cooling/air hose as shown in the pictures Accessories as shown in the pictures   Condition:   Used Optical condition as shown in the pictures Signs of wear and tear due to age and use Functionality not tested   Sold exclusively as a source of spare parts. The device is explicitly not offered as a functional machine. No guarantee for functionality, operational readiness, or completeness.   Shipping or freight shipping possible. Subject to changes, errors, and prior sale.   We will gladly answer any further questions by telephone.

Year of construction: 2025, condition: repair required (used), functionality: limited functionality, machine/vehicle number: 54942, No minimum price – guaranteed sale to the highest bidder! EXW – Dismantling and loading must be organized by the buyer! TECHNICAL DETAILS Nominal test force: 50 kN Test stroke: < 1,400 mm Usable distance between pressure plates: approx. 800 mm Test area width: 500 mm Test speed: continuously variable 0.001–1,200 mm/min Resolution of displacement measurement: ≤ 0.001 mm Diameter of pressure plates: 246 mm Centering bore: 40 mm Thread: M12 Hardness: ≥ 56 HRC Design: Steel, hardened, rotatable at the top and bottom, lockable at 0° Measuring range of the enveloping circle: 30–250 mm Design: Probe with bearing rollers Measurement: Recording under load MACHINE DETAILS Control system: Control system with control computer Test program: Enveloping circle measurement Network: Fast Ethernet, 100 Mbit/s between the control computer and the separately required operating PC Software delivery: USB stick with installation software Documentation: Version and license status not documented separately Last calibration: 08/04/2025 Dimensions & Weight Machine dimensions: approx. 750 × 900 × 1,950 mm Base frame dimensions: approx. 730 × 900 × 700 mm Control cabinet with control computer dimensions: approx. 600 × 600 × 1,900 mm Machine weight: approx. 490 kg Base frame weight: approx. 50 kg Voltage supply: 3 × 400 V AC, 50 Hz, N + PE Type plate power: 3,000 W Connected power: approx. 3 kVA EQUIPMENT Base frame Control cabinet with control computer Rotatable pressure plates Enveloping circle measuring device with probes and bearing rollers USB stick with installation software Compressed air connection: Pneumatic connection with shut-off valve Pgedpfxez Tf D Rj Akiju Note: The functionality has been tested and confirmed. However, an unresolved error message on the drive prevents further use. The machine is in like-new condition visually. The operating PC is not included in the offer.

Condition: excellent (used), Year of construction: 2000, functionality: fully functional, Weiler Praktikant 160 B, lathe with guide and draw spindle, year of manufacture 2000, with 3-axis digital display K&C, NEW, CE marking!! Technical data: Pjdpfj Afxq Sjx Akisgu >> Year of manufacture 2000, machine no. 4651 >> Center height 160 mm >> Distance between centers 650 mm >> Spindle speeds: from 24 to 2500 rpm >> Spindle bore 40 mm >> Short taper spindle head DIN 55027 size 5 with bayonet lock >> Tailstock MK 3 >> Feeds from 0.02 to 0.63 mm/rev >> Possible threads: metric, inch, module and diametral pitch >> Metric thread pitches from 0.25 to 8 mm >> Weight approx. 680 kg >> Spindle brake can be switched on >> Length 1.6 m, height 1.25 m, depth 0.7 m Accessories and equipment: >> 3-axis digital display from K&C, new, 12 months manufacturer's warranty, with operating manual Functions: switching mm/inch, coordinate selection ABS/INC, halving the display value, reference mark, tool programming 200 pieces, taper calculation, radius/diameter, quick zeroing, switching the counting direction >> Quick-change tool holder, collets from 2 to 28 mm, increasing in 1 mm steps >> 3-jaw chuck 160 mm Röhm with 2 sets of jaws >> Mulifix size A with 2 steel holders >> Electric chuck guard >> Bed stop, drill chuck >> Back wall >> Machine feet >> Coolant system >> Operating manual, parts list (PDF) About the machine: Offered is a Weiler Praktikant 160 B lathe with guide and draw spindle, year of manufacture 2000, in very good condition. The machine is fully functional and has CE marking. All slides run very smoothly and evenly. The Weiler comes from a training workshop. Even at high speeds, the Weiler runs smoothly. This newer generation of Weiler lathes is very user-friendly and allows for the production of surfaces that appear to be ground. Take the opportunity to inspect this machine on site and under power to convince yourself of its condition.

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2007, operating hours: 70,192 h, laser hours: 21,800 h, laser power: 2,700 W, TruMatic 6000 K01 (1600) Large-format, 2700 Watt NC: 70192 h Laser on: 70000 h Beam on: 21800 h Sheetmaster Gripmaster+ shear Loading and unloading cart Fire extinguishing system Parts conveyor Options: Multishear Thread forming Marking/Signing Pgjdps Afxvgsfx Akiou

Condition: new, functionality: fully functional, Year of construction: 2026, overall weight: 100 kg, total height: 1,000 mm, color: red, continuous operating pressure: 210 bar, spindle torque (max.): 1,800 Nm, Equipment: hydraulics, Cone splitter Excavator splitter Drill cone splitter Wood splitter KS5 Drill cone 200x400 - Made in Germany The powerful cone splitter for attachment to mini-excavators, excavators, wheel loaders, tractors, skidders and many other options. The drill cone can be exchanged for various tools such as a root cutter, auger, hummus sieve, concrete mixing drum, weed broom and many other attachments. The cone splitter consists of a very stable drive unit and the drill cone (splitting cone) The drill cone is completely hardened. It is not made of unhardened steel as is the case with many other manufacturers. It can be converted to other tools in a few simple steps. - Cone splitter - Root cutter - Earth auger - Weed brush - Sweeping broom - Rotary harrows NO CHINA GOODS ! WE PRODUCE IN GERMANY ! THE ideal multi-purpose tool for foresters, farmers, gardeners, do-it-yourselfers and professionals Overall length 600 mm plus attachment and interchangeable system Universally applicable in construction, forestry, agriculture and horticulture For splitting heavy firewood or wood for wood chips For drilling holes in the ground, for stakes, plants and much more For removing rootstocks and tree stumps For cleaning trenches and paved areas For levelling garden areas and creating a fine soil structure You simply do the work from the excavator without any further assistance. A very solid and stable steel construction enables you to work hard and for a long time. In addition to the motor, the shaft is supported by 2 sturdy tapered roller bearings to protect against tension and pressure. The tapered roller bearings can be lubricated for a long service life. A powerful HMT 500 hydraulic motor with up to 1,800 Nm gives you the necessary torque for efficient work, from 25 l/min up to 125 l/min and 210 bar pressure Weight 70 kg included: - Drive unit with powerful HMT hydraulic motor, weight 70 kg Pgodpouph Uxofx Akieu - Drill cone with tip Ø 200 mm 270 mm/400 mm long, 6xM16 thread LK173 on the front side Total length 270 mm + drill cone tip 130 mm = 400 mm Diameter 200 mm Weight 30 kg Total weight 100 kg

Condition: new, Year of construction: 2026, Hydraulic winch HAW1700 with electric valve incl. manual operation and radio remote control for mounting on wood splitters, cranes, mini excavators, tractors, forklifts, mowing tracked vehicles, and telescopic loaders, for use in viticulture and horticulture, agriculture, construction, and forestry, as well as many other applications. Equipped with an electric hydraulic valve and radio remote control. The hydraulic winch HAW1700 can simplify many tasks. Maximum rope capacity of 30 m with 6 mm wire rope. Standard equipment includes 20 m of 6 mm wire rope. ⦁ Pull and position firewood for the wood splitter ⦁ Pull logs onto a trailer ⦁ Pull out tree stumps and trees ⦁ As an auxiliary winch on skidders and small excavators ⦁ As a winch for small tractors and narrow-gauge tractors A robust steel construction with the possibility of mounting on both sides (bottom, rear, top) with M12 threads. This allows for flexible use of the winch. Large, double-bearing rope pulley for long wire rope life. The pulling force is 1700 kg as standard. The winch can be installed in various positions. An optional hydraulic brake is available. Depending on the required pulling speeds and forces, we can offer you different options. Please contact us, and we will be happy to advise you. ⦁ Maximum working pressure: 225 bar peak ⦁ Continuous operating pressure: 175 bar ⦁ Displacement: 400 ccm ⦁ Torque at 225 bar: 870 Nm peak ⦁ Torque in continuous operation: 380 Nm ⦁ Maximum pulling force: 1700 kg ⦁ Weight: 49 kg Pjdpfxefn Tvhj Akijgu ⦁ Rope speed: 47 m/min at 60 l/min oil flow ⦁ Color: red ⦁ Including hoses from the valve to the motor Dimensions: ⦁ Length: 500 mm ⦁ Length with rope inlet: 570 mm ⦁ Front width: 120 mm ⦁ Rear width: 180 mm ⦁ Bearing width: +30 mm ⦁ Motor width: +200 mm ⦁ Height: 250 mm Included: Radio remote control for the winch. ⦁ Control range: up to 100 m ⦁ Temperature: -35 °C to +80 °C Protection class: IP65

Condition: new, functionality: fully functional, Year of construction: 2026, machine/vehicle number: HAW1700-EV-Funk, rope length: 30,000 mm, rope speed: 47,000 mm/min, Hydraulic winch for wood splitters, cranes, mini excavators, tractors, agricultural vehicles, viticulture, horticulture, and many other applications. The hydraulic attachment winch simplifies many tasks: - Pulling and positioning firewood to the wood splitter - Pulling logs onto trailers - Removing tree stumps and roots - As an attachment winch on forestry cranes and small excavators Pedpfx Aksdf Ufpeisgu - As a winch for small tractors and narrow-gauge tractors A robust steel construction with 3-sided mounting options (left, right, rear) and 12 threaded holes offers many possibilities for attaching the winch (threads are cut and painted. They need to be re-cut with a thread tap before use due to the rust protection). A 20 m long and 6 mm thick steel cable is mounted. A large cable pulley ensures a long service life for the steel cable. We mount hydraulic motors from 50 to 630 cc (standard = 400 cc), depending on the speed and pulling force required. Maximum working pressure: 225 bar peak Continuous operating pressure: 175 bar Displacement: 400 cc Torque at 225 bar: 870 Nm peak Torque in continuous operation: 380 Nm Maximum pulling force: 1700 kg Weight: 49 kg Cable speed: 47 m/min at 60 L/min hydraulic oil Color: red Dimensions: Length: 500 mm Length with swivel: 570 mm Front width: 120 mm Rear width: 180 mm Bearing width: + 30 mm Motor width: + 200 mm Height: 250 mm The winch is available for mounting or welding. This version includes an electric hydraulic valve, remote control, and hoses to the motor. Article number: HAW1700-EV-Funk

Condition: used, functionality: fully functional, This used STOW pallet rack is a compact, high-performance heavy-duty racking system designed to meet industrial warehousing demands. The modular high bay racking is ideally suited for logistics centers, industrial applications, large warehouses, and freight forwarding companies. With a shelf load capacity of up to 2,250 kg per level and a bay load of up to 9,000 kg, this immediately available pallet racking system provides an efficient solution for storing Euro pallets and heavy load units. Pgodpfx Ae Aggk Sokisu PRODUCT DETAILS: - Height: approx. 1,050 cm - Depth: approx. 110 cm - Length: approx. 1,400 cm - Shelf load: 2,250 kg - Beams: approx. 270 x 12 x 5 cm PNB0472 - Beam color: yellow powder-coated - Frames: approx. 1,050 x 110 cm, pre-assembled - Frame color: blue powder-coated - Levels: Floor + 4 - Pallet positions: 75 including positions at floor level - Version: Used STOW system SCOPE OF DELIVERY: - 06 x frames (approx. 1,050 x 110 cm), pre-assembled - 40 x beams (approx. 270 x 12 x 5 cm) PNB0472 - 80 x safety clips Price: €2,080.00 net €2,475.20 gross An invoice with VAT shown will be provided. DELIVERY, INSTALLATION & INSPECTION: - Nationwide delivery within Germany by our partner carriers – freight costs depend on your postal code - Professional assembly and dismantling by trained teams available as an option - Rack inspections according to DIN EN 15635 by certified inspectors - Inspection of existing heavy-duty racks from other manufacturers possible PLANNING & CONSULTING: Our planning department will be happy to prepare a tailored, no-obligation offer according to your requirements. Whether for new builds, conversions, or expansions – we provide expert advice on your racking configuration. SHOWROOM: We invite you to visit our showroom! Here you can get a comprehensive impression of our pallet racks, storage racks, and additional solutions. Many systems are on display and ready for hands-on inspection. Our expert advisors are available for your questions and personal consultation – we look forward to welcoming you! Haven’t found the right solution yet? Visit our website for a quick overview of many offers and product variations! INTERESTED OR HAVE QUESTIONS? Please contact us via message or phone call. You’ll find our phone number on our company profile. ☎️ We are available by phone Monday to Friday, 08:00 - 16:00. Alternatively, send us a message with your name and number and we will call you back as soon as possible.