Used Swiss Traction for sale (3,688)

Condition: like new (used), functionality: fully functional, Weiler Commodor guide and feed spindle lathe with 3-axis digital display K&C NEW Overhauled with acceptance certificate for tolerances of new machines Technical data: Gtjdjvrcqdopfx Afneu >> Machine no. 1824 >> Center height 180 mm >> Center width 1000 mm >> Spindle speeds: from 13 to 2000 rpm >> Spindle passage 56 mm >> Short taper spindle head DIN 55029 size 5 >> Tailstock MK 4 >> Feed rates from 0.026 to 0.888 mm / rev >> Possible threads metric, inch, module and diametric pitch >> Metric thread pitches from 0.35 to 12 mm >> Weight approx. 1500 kg >> Spindle brake can be switched on >> Drive power 2.0/4.0 KW >> Length 2.2 m, height 1.5 m, depth 1 m Accessories and equipment: >> 3-axis digital display from K&C New, 12-month manufacturer's guarantee with operating instructions Functions: Switching mm/inch, coordinate selection ABS/INC, halving of the display value, reference mark, tool programming 200 pcs., cone calculation, radius / diameter, quick zeroing, switching of the counting direction, >> Three-jaw chuck wedge bars as good as new 200mm 1 set of jaws >> Mulifix size B with 2 pcs steel holders NEW >> Bed stop >> Machine feet >> Coolant system >> LED machine lamp For safety, the machine is equipped with: >> Electronic spindle protection >> Spindle brake >> 2 emergency stops On request: covers for the guide. and feed spindle About the machine: A Weiler Commodor guide and feed spindle lathe is offered in a geometrically overhauled condition. The guides have been reground or re-scraped. With acceptance according to the test report. 2K glossy white paint. The Multifix and chuck accessories are new. For safety: The machine has a brake motor, electronic spindle protection and two emergency stops - an absolutely new lathe. Even at high speeds, the Weiler runs very quietly. This new generation of Weiler lathes is very user-friendly and surfaces can be produced as if they were ground. Take the opportunity to view this machine on site under power and see for yourself its condition.

Condition: like new (used), functionality: fully functional, Weiler Commodor guide and feed spindle lathe with 3-axis digital display K&C NEW Overhauled with acceptance certificate for tolerances of new machines Technical data: >> Machine no. 2020 >> Center height 180 mm >> Center width 1000 mm >> Spindle speeds: from 13 to 2000 rpm >> Spindle passage 56 mm >> Short taper spindle head DIN 55029 size 5 >> Tailstock MK 4 >> Feeds from 0.026 to 0.888 mm / rev >> Possible threads metric, inch, module and diametrical pitch >> Metric thread pitches from 0.35 to 12 mm >> Weight approx. 1500 kg >> Spindle brake can be switched on >> Drive power 2.0/4.0 KW >> Length 2.2 m, height 1.5 m, depth 1 m Accessories and equipment: >> 3-axis digital display from K&C New, 12-month manufacturer's guarantee with operating instructions Functions: Switching mm/inch, coordinate selection ABS/INC, halving of the display value, reference mark, tool programming 200 pcs., cone calculation, radius / diameter, quick zeroing, switching of the counting direction, >> Three-jaw chuck wedge bars as good as new 200mm 1 set of jaws >> Mulifix size B with 2 pcs steel holders NEW >> Bed stop >> Machine feet >> Coolant system >> LED machine lamp For safety, the machine is equipped with: >> Electronic spindle protection >> Spindle brake Gedpfx Afsvrckqjnetu >> 2 emergency stops On request: covers for the guide. and feed spindle About the machine: A Weiler Commodor guide and feed spindle lathe is offered in a geometrically overhauled condition. The guides have been reground or re-scraped. With acceptance according to the test report. 2K glossy white paint. The Multifix and chuck accessories are new. For safety: The machine has a brake motor, electronic spindle protection and two emergency stops - an absolutely new lathe. The Weiler runs very quietly even at high speeds. This new generation of Weiler lathes is very user-friendly and surfaces can be produced as if they were ground. Take the opportunity to view this machine on site under power and see for yourself its condition.

Condition: excellent (used), functionality: fully functional, Weiler Primus guide and feed spindle table lathe in excellent condition! Technical specifications: >> Machine no. 2801 >> Center height 120 mm >> Center distance 430 mm >> Speed: 60 - 3000 rpm in 18 gear steps >> Spindle bore 23 mm >> Short-taper spindle head DIN 55027 >> Tailstock MT 2 Gedsv Tyzcepfx Afnotu >> Feed rates from 0.03 to 0.15 mm/rev >> Possible thread sizes: metric, inch, module, and diametrical pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 1 x Röhm 125 mm three-jaw chuck with 4 sets of jaws >> Collet chuck with collets from 2 mm to 12 mm, increments of 1 mm Drawbar >> Multifix size A with 4 tool holders >> Change gears >> Fixed steady rest >> Faceplate >> Spindle cover >> Clamping tool About the machine: Offered is a Weiler Primus table lathe with guide rail and drawbar in very good condition. The machine is fully functional. All slides run very smoothly and evenly. Even at high speeds, the Weiler runs quietly. The Primus comes from a state-owned company where it was used little. This newer generation of Weiler lathes is very user-friendly, and surfaces can be produced with a polished finish. Take advantage of the opportunity to view this machine on-site under power and see for yourself its condition. (The base cabinet is included; the machine is not bolted to the machine.) A digital display is available for an additional charge.

Condition: used, functionality: fully functional, Weiler Matador VS-2 guide and feed spindle lathe Technical data: Gtodpfjvv Etvsx Afnou >> Year of manufacture approx. 1970 Machine no. M1012 >> Center height 140 mm >> Center width 500 mm >> Speed: 30 – 3550 rpm >> Spindle passage 36 mm >> Short taper spindle head DIN 55022-5 with bayonet lock >> Tailstock MK 3 >> Feed rates from 0.010 to 1.184 mm / rev >> Possible threads metric, inch, module and diametric pitch >> Metric thread pitches from 0.25 to 15 mm >> Weight approx. 700 kg >> Length 1.4 m, height 1.2 m, depth 0.55 m Accessories and equipment: >> Collet device 32 collets (set is not complete) with holder >> 1 three-jaw chuck 1 set of jaws >> 1 four-jaw chuck 1 set of jaws >> Mulifix size A with 2 steel holders >> Change gears >> Bed stop About the machine: A used Weiler Matador VS-2 is offered in a fully functional condition. Take the opportunity to view this machine on site under power and see for yourself its condition.

Condition: excellent (used), functionality: fully functional, Emcomat 17D Lead and Feed Screw Lathe with 3-Axis Digital Readout K&C New from Training Workshop Excellent Condition!!! Technical Data: >> Year of manufacture: approx. 2000 >> Machine no.: D3F H1 010 >> Centre height: 170 mm >> Swing over bed: 340 mm >> Swing over cross slide: 190 mm >> Turning length: 700 mm >> Spindle speed: 4 speed ranges, stepless from 35 to 3000 rpm >> Tailstock quill stroke: 120 mm >> Tailstock: MT3 >> Spindle bore: 50 mm >> 20 longitudinal feeds: 0.045 – 0.787 mm/rev >> 20 cross feeds: 0.023 – 0.406 mm/rev Gsdpfx Afowvuf Tjnetu >> Required floor space approx. (L x D x H): 1.600 x 0.9 x 1.3 meters >> Weight: approx. 730 kg Equipment and Accessories: >> 3-axis digital readout from K&C, new, with 12 months manufacturer’s warranty and operating manual Functions: mm/inch switching, coordinate selection ABS/INC, value halving, reference point, tool programming for 200 tools, taper calculation, radius/diameter display, quick zeroing, count direction switching >> 1 piece three-jaw chuck NEW 160 mm, 2 sets of jaws >> Multifix B toolholder with 2 tool pockets >> Chip guard >> Coolant system About the machine: Offered here is an Emcomat 17D lead and feed screw lathe, approx. year 2000, in very good condition. The machine is of course fully functional. The bedways are in excellent condition. The Emco is equipped with a new 3-axis digital readout from K&C and a new three-jaw chuck. Take the opportunity to inspect the machine under power on site and see the condition for yourself.

Condition: like new (used), functionality: fully functional, Weiler Praktikum 160B precision center lathe 3-axis digital display K&C NEW. Reconditioned with acceptance certificate for tolerances of new machines Technical data: >> Machine no. 87 160 760 >> Center height 160 mm >> Center width 650 mm >> Spindle speeds: from 24 to 2500 rpm >> Spindle passage 40 mm >> Short taper spindle head DIN 55027 size 5 with bayonet lock >> Tailstock MK 3 >> Feed rates from 0.02 to 0.63 mm / rev >> Possible threads metric, inch, module and diametric pitch >> Metric thread pitches from 0.25 to 8 mm >> Weight approx. 680 kg >> Spindle brake can be switched on >> Length 1.6 m, height 1.25 m, depth 0.7 m Accessories and equipment: >> 3-axis digital display from K&C New, 12-month manufacturer's guarantee with operating instructions Functions: Switching mm/inch, coordinate selection ABS/INC, halving the display value, reference mark, tool programming 200 pcs., cone calculation, radius / diameter, quick zeroing, switching the counting direction, >> Collet device New, collets NEW from 3 to 25 mm, 1 mm increasing Gtodpfxovrdlcj Afnou >> Three-jaw chuck 160 mm New with 2 sets of jaws >> Mulifix size A with 3 steel holders >> Electronic spindle protection >> Machine lamp LED New >> Machine feet NEW >> Splash guard >> Operating instructions, spare parts plan (PDF) About the machine: Offered is a Weiler Praktikum 160 B guide and feed spindle lathe with toolmaker precision in a completely geometrically overhauled condition. Reconditioned with acceptance certificate for tolerances of a new machine. For safety: Electronic spindle protection of the work spindle, cover of the lead and feed spindle, 2 emergency stops and a brake motor. This new generation of Weiler lathes is very user-friendly and surfaces can be produced as if they were ground. Take the opportunity to view this machine on site under power and see for yourself its condition.

Condition: like new (used), functionality: fully functional, Weiler center lathe Model Condor 81 guidance and feed spindle lathe with 3-axis digital display from K&C, NEW Geometrically overhauled with inspection protocol for new machine tolerances Technical data: >> Machine No. 84-121 >> Center height 165 mm >> Center distance 750 mm >> Spindle speeds: from 22 to 2800 rpm >> Spindle bore 40 mm >> Short taper spindle head DIN 55027 size 5 with bayonet lock >> Tailstock MK 3 >> Feeds from 0.015 to 0.46 mm/rev >> Possible threads: metric, imperial, module, and diametral pitch >> Metric thread pitches from 0.18 to 28 mm >> Weight approx. 1100 kg >> Spindle brake switchable >> Length 1.83 m, Height 1.29 m, Depth 0.88 m Equipment and accessories: >> 3-axis digital display from K&C, new, 12 months manufacturer warranty with operating instructions Functions: switching mm/inch, coordinate selection ABS/INC, value halving, reference mark, tool programming for 200 pcs., taper calculation, radius/diameter, quick zeroing, count direction switching Gsdpfxswrm Dto Afnetu >> Collet chuck NEW, collets NEW from 3 to 26mm, increments of 1mm >> 160 mm three-jaw chuck with 2 sets of jaws NEW >> Multifix size B NEW with 3 piece steel holders >> Bed stop >> Electric chuck guard NEW >> Rear wall >> Operating manual >> Coolant device >> Machine feet About the machine: A Weiler Condor 81 guide and feed spindle lathe in a very good, geometrically overhauled condition is being offered. The guides are newly ground or newly scraped. Inspected according to test protocol. The accessories collets and chuck are new. For safety: The machine has a brake motor, electronic spindle guard and two emergency stops, making it an absolutely as-new lathe. Even at high speeds, the Weiler runs very smoothly. This newer generation of Weiler lathes is very user-friendly and allows surfaces as if ground to be produced. Take the opportunity to view this machine on site under power and convince yourself of its condition.

Condition: excellent (used), Year of construction: 1986, functionality: fully functional, Weiler Praktikant 160 B lead and feed screw lathe with 3-axis digital readout K&C NEW Technical data: >> Year of manufacture: 1986, machine number 86-160-348 >> Center height: 160 mm >> Distance between centers: 650 mm >> Spindle speeds: 8 steps; from 96 to 2500 rpm >> Spindle bore: 40 mm >> Short taper spindle head DIN 55027 size 5 with bayonet lock >> Tailstock: MT 3 >> Feeds: 0.02 to 0.63 mm/rev >> Usable threads: metric, inch, module, and diametral pitch Gsdpfxjwthbij Afnetu >> Metric thread pitches: 0.25 to 8 mm >> Weight: approx. 680 kg >> Spindle brake switchable >> Length 1.6 m, height 1.25 m, depth 0.7 m Accessories and equipment: >> 3-axis digital readout from K&C, new, 12 months manufacturer warranty with operating manual Functions: mm/inch switching, coordinate selection ABS/INC, value halving, reference point, tool programming for 200 tools, taper calculation, radius/diameter display, quick zeroing, direction reversal >> Collet clamping device, collets as new from 1 to 29 mm in 1 mm increments >> 160 mm new three-jaw chuck with 2 sets of jaws >> Multifix size A with 3 tool holders >> Electric chuck guard >> Bed stop >> Rear wall >> Machine leveling feet >> Coolant device About the machine: Offered is a Weiler Praktikant 160 B lead and feed screw lathe built to toolroom precision in very good condition. The machine is, of course, fully functional. The Weiler was completely dismantled and newly painted in light grey. All slides move very smoothly and evenly. Even at high speeds, the Weiler runs quietly. This newer generation of Weiler lathes is very user-friendly and can produce surfaces as if ground. Take the opportunity to inspect the machine under power on site and verify its condition for yourself.

Condition: excellent (used), Year of construction: 1995, functionality: fully functional, Emcomat Emco EM20D Lead and Feed Lathe, built in 1995, in excellent condition, CE compliant! Technical specifications: >> Year of manufacture: 1995 >> Center height 200 mm >> Swing over bed 400 mm >> Swing over cross slide 250 mm Gedpfowag Stex Afnotu >> Turning length: 1000 mm >> Spindle speed: 4 speed levels, continuously variable from 35-3000 rpm >> Quill stroke 120 mm >> Tailstock: MT3 >> Spindle bore: 50 mm >> 20 longitudinal feeds 0.045 / 0.787 mm/rev >> 20 cross feeds 0.023 / 0.406 mm/rev >> Space requirements / installation dimensions approx. length 1.900 x depth 0.9 x height 1.3 meters >> Weight approx. 850 kg Accessories and equipment: >> 3-axis position indicator >> 1 piece Three-jaw chuck with 1 set of jaws >> Tool holder with 3 pockets >> Chip return wall >> Coolant system >> Bed stop About the machine: Offered is an Emcomat 20D centerline and feed spindle lathe, built in 1995, in lightly used condition. The machine is fully functional. All slides run very smoothly and evenly. The bed guides are in very good condition. Take advantage of the opportunity to view this machine on-site under power and see for yourself its condition.

Condition: used, mileage: 743,059 km, power: 520 kW (707.00 HP), first registration: 03/2019, fuel type: diesel, empty load weight: 9,700 kg, maximum load weight: 16,300 kg, overall weight: 40,000 kg, tire size: 385 / 55 R 22.5 / 5mm, axle configuration: 6x2, wheelbase: 3,000 mm, next inspection (TÜV): 03/2025, driver cabin: sleeper cab, gearing type: semi-automatic, emission class: euro6, suspension: air, total length: 6,500 mm, total width: 25,500 mm, total height: 40,000 mm, front tire size: 385 / 55 R 22.5 / 5mm, number of seats: 2, operation weight: 26,000 kg, Equipment: air conditioning,

Condition: used, power: 419 kW (569.68 HP), axle configuration: 6x6, color: green, driver cabin: sleeper cab, gearing type: automatic, emission class: euro6, Year of construction: 2024, Equipment: ABS, EBS, air conditioning, - Brake system Iveco X-Way AS300X57 Z/P HR ON+ Short Timber Truck, axle configuration 6X4 (with hydraulically driven front axle 6x6), tandem medium drive axle (HR), disc brakes, cab version Active Space, large driver's cab, rear air suspension, 12-speed automated HiTroniX transmission, engine 570 C13 Cursor 13 570 HP Euro VI, wheelbase 4,800 mm, AS cab with high roof, roof insulation for cab, electrically operated lifting roof transparent for MLL high roof, air suspension for cab, fog lights, front halogen headlights, electrically adjustable and heated mirrors, hybrid bumper, front underrun protection, static passenger seat, one-piece lower bed, double thermo insulated box, digital tachograph 4.0, electronic immobilizer and 2nd vehicle key, luxury driver's seat air-sprung, heated, 4-way adjustable, lumbar and headrest with integrated 3-point seat belt, 2 reinforced anti-roll bars on rear axle, designed for moderate climates, exhaust outlet to the left, 170 Ah batteries, horizontal batteries on frame, rear suspension without spacers, generator 2,160 watts (24 volts x 90 amps), 2-cylinder air compressor 630 cc, rear shock absorbers, trailer socket for 24-volt operation, 15-pin, rear axle ratio: 4.23, heated fuel prefilter with separator, adaptive cruise control (ACC), ECO-Switch to switch between Power and Eco mode to optimize Total Cost of Ownership (TCO) by fuel-optimized engine and transmission settings, driving style analysis (DSE), transmission software eco-roll freewheeling function, VDI interface (Vehicle-Data-Interface) for telematics services (FMS) version 3.0, preparation for toll system (OBU), preparation for telematics system (telematics box), hill start assist (Hill Holder), electronic stability program (ESP), lane departure warning system (LDWS), emergency braking assistant, HI-TRACTION, rocking mode (free swing mode), left and right luggage compartments, 15m tire inflation hose, headlamp protection grilles, fully automatic air conditioning, leather multifunction steering wheel, sun roller blind, auxiliary heater diesel/water 4KW, front axle 8,000 kg / 1st rear axle 10,500 kg / 2nd rear axle 10,500 kg, spare wheel, reinforced front anti-roll bar, reinforced parabolic spring on front axle, AdBlue tank 80 liters, 50 mm 190 kN Ringfeder trailer coupling, fuel tank 550 liters, CAN bus interface CAN-OPEN for body control, infotainment system incl. navigation, axle load indicator, holding effect of parking brake on front axle, LED tail lights, retarder/intarder for ZF transmission, side marker lights, tires 385/65 R22.5 - 315/80 R22.5, bumper painted in cab color, aluminum air tanks, horn behind bumper, transparent sun visor. SCHEMEL–SHORT TIMBER BODY Crane: Palfinger-EPSILON loading crane Y_CRANE_ON_2 M 12 Z91 - Fully hydraulic timber loading crane Manufacturer: EBERT Dimensions: approx. 6,750 mm between bulkhead and crane - 4 ExTe bolsters D5 – adjustable with clamp fastener and lashing ratchets or support for load securing - with 8 ExTe stakes D5 – telescopic - with special Z-profile subframe 200 mm high, closed with checker plate in the center of the frame - Bulkhead welded construction with internal special aluminum profiles approx. 2,600 mm high - 4 x ¼ mudguards... Godpfx Afjyfu Rmjnotu

Condition: used, power: 419 kW (569.68 HP), axle configuration: 6x6, color: green, driver cabin: sleeper cab, gearing type: automatic, emission class: euro6, Year of construction: 2026, Equipment: ABS, EBS, air conditioning, - Braking system Iveco S-Way AS300X57 Z/P HR ON+ Short Timber Truck, axle configuration 6X4 (with hydraulically driven front axle 6x6), tandem medium rear axle with outer wheels (HR), disc brakes, cab version Active Space, large cab, rear axle air suspension, 12-speed automated HiTroniX transmission, engine 570 C13 Cursor 13 570hp Euro VI, wheelbase 4800 mm, AS high-roof cab, cab roof insulation, electrically operated lift-up roof, transparent with MLL high-roof, air suspension for cab, fog lights, front halogen headlights, electric adjustable and heated mirrors, hybrid bumper, front underride guard, static passenger seat, one-piece lower bunk, double thermo-insulated box, digital tachograph 4.0, electronic immobilizer and 2nd vehicle key, luxury driver’s seat air-suspended, heated, 4-way adjustable, lumbar and headrest with integrated 3-point seatbelt, 2 reinforced stabilizer bars rear axle, moderate climate version, exhaust tailpipe left, 170Ah batteries, horizontal batteries on frame, rear spring without spacer, generator 2160W (24V x 90A), 2-cylinder air compressor 630cc, rear shock absorbers, 24V trailer socket 15-pin, rear axle ratio: 4.23, heated fuel pre-filter with separator, adaptive cruise control (ACC), ECO-switch for switching between Power and Eco mode to optimize Total Cost of Ownership (TCO) via fuel-efficient engine and transmission calibration, driving style analysis (DSE), gearbox software with ECO-Roll freewheeling function, VDI interface (Vehicle Data Interface) for telematics services (FMS) version 3.0, prepped for toll system (OBU), prepped for telematics system (telematics box), hill start assist (Hill Holder), electronic stability program (ESP), lane departure warning assist (LDWS), emergency brake assist, HI-TRACTION, rocking mode (rock-free mode), luggage compartments left and right, 15m tire inflating hose, headlamp protection grill, fully automatic air conditioning, multifunction leather steering wheel, sun visor blind, diesel/water auxiliary heater 4kW, front axle 8,000kg / first rear axle 10,500kg / second rear axle 10,500kg, spare wheel, reinforced front stabilizer, reinforced parabolic spring on front axle, AdBlue tank 80L, 50mm 190kN Ringfeder trailer coupling, fuel tank 550L, CAN-Bus CAN-OPEN interface for body control, infotainment system incl. navigation, axle load indicator, parking brake holding force on front axle, LED rear lights, retarder/intarder for ZF gearbox, side marker lights, tires 385/65 R22.5, 315/80 R22.5, hybrid bumper painted in cab color, aluminum air tanks, horn behind bumper, transparent sun visor. SCHEMEL–SHORT TIMBER–ALUMINUM BODY Crane: Palfinger-EPSILON loader crane Y_CRANE_ON_2 M 12 Z91 - fully hydraulic timber loader crane Manufacturer: EBERT Godpfxeyfq Dvo Afnstu ALUCAR Dimensions: approx. 6,750 mm between bulkhead and crane - 4 ExTe bunks D5 – installed with ExTe clamp mountings, Alucar stops as mechanical securing of bunks, ExTe lashing points (hook or ring system) - 8 ExTe aluminum stakes D-5, telescopic, or C-5, telescopic, complete with ExTe stake mountings - Alucar aluminum subframe HD, height 195 mm, double cranked...

Condition: good (used), Centre height: 290 mm Swing diameter over bed: 580 mm Centre distance: 3000 mm Weight: 2800 kg Gtodpfx Aoxtu Erofnju Equipped with a ZIMMER DY 75 flat belt grinder, year of manufacture 2010, e.g. for shaft or tube grinding Siegfried Volz Werkzeugmaschinen Rüschebrinkstr. 151-153 DE - 44143 Dortmund - Wambel

Condition: reconditioned (used), Year of construction: 1956, Lead and Feed Screw Lathe WEIPERT Gtedpfx Ajw Ew D Dofneu Year of manufacture: 1956 Spindle bore: 90 mm Centre distance: 3000 mm Swing over bed: 800 mm Swing over cross slide: 610 mm Swing in gap: 1120 mm Speed range: 7.5 – 475 rpm Comes with the following accessories: Multifix toolholder with 11 inserts Coolant system 3-jaw chuck 315 mm 3-jaw chuck 400 mm 3-jaw chuck 500 mm Faceplate 400 mm Faceplate 800 mm Faceplate 1000 mm Travelling steady Various turning tools (30 insert tools) 2 revolving centres 1 drill chuck Operating manual

Condition: new, Year of construction: 2025, CONDOR VC plus The new dimension in conventional precision lathes. A high-quality, powerful and energy-efficient precision lathe for the highly productive area of production and toolmaking, but also for training and further education High-quality, energy-efficient, precise and universally applicable in production, training and further education. It impresses with: future-oriented technology maximum accuracy durability user-friendly ergonomics minimum space requirement and a wide range of accessories. The consistent and innovative further development of the tried-and-tested Condor series is the economical and intelligent solution for your daily applications. Technical data: WORKING AREA Center height 180 mm Swing diameter over bed 360 mm Swing diameter over facing slide 190 mm Center width 800 mm TURNING SPINDLE Spindle head DIN 55027/DIN ISO 702-3 size 6 Gtedpfx Asqwipnsfneu Spindle bore 57 mm Spindle diameter in front bearing 90 mm MAIN DRIVE Drive power 60 %/100 % ED - / 10.5 kW Speed range 25 - 4,000 min-1 Number of speeds infinitely variable FEED RANGE Number stepless Longitudinal 0.01 - 6 mm/rev Plan 0.003 - 2 mm/rev THREAD CUTTING RANGE Metric thread 0.1 - 20 mm REITSTOCK Quill diameter 50 mm Quill stroke 110 mm Internal taper DIN 228 MK 3 ACCEPTANCE ACCURACY DIN 8605 Equipped with WEILER WTS 15 VC plus screen display - Large, clearly arranged 15" touch screen, rotatable and tiltable, resolution 1366 x 768 - Change of operating screens via swipe movements - Operating functions can be called up via app manager - Control panels can be freely configured, placed and scaled as required - Drawings / sketches can be imported from PDF files Can be zoomed individually via USB interface - Video-supported maintenance of the machine - Context help menu (instead of screen display WEILER VC plus) The machine is located in our showroom in 71334 Waiblingen-Beinstein and is available immediately. Please contact us regarding equipment.

Condition: good (used), Used COLCHESTER MASTER 3250 center lathe and feed spindle lathe Gsdpfxsuqkf Ns Afnstu center height 170mm center distance: 650mm spindle bore: 42mm Infinitely variable speed from 15-3250 rpm 1 x SCHUNK wedge bar lathe chuck Ø160mm 1 x MULTIFIX steel holder size B with 4 inserts Machine light, chuck protection electrically fused, machine shoes 1 x rotating center point, 1 x rotating center point with pressure indicator 1 x drill chuck with tapered arbor The machine is located at our premises in 71334 Waiblingen-Beinstein and is available immediately. An inspection of the machine is possible by arrangement.

Condition: new, Year of construction: 2025, GSD Intern One of the best-selling and most popular conventional precision lathes Impressive thanks to: Sophisticated technology Highest accuracy Durability Proven ergonomics Minimal footprint And extensive accessories. Proven for decades in single-part and small-batch production, in trade and industry, training and continuing education, and tool and fixture construction. Distance between centers 650 mm Center height 160 mm Automatic handwheel disengagement Leadscrew and feed screw covers Main spindle brake Toolmaking precision according to DIN 8605 Pole-changing brake motor Headstock gearbox 16 fixed speed levels Numerical position display (option) LED machine light TECHNICAL DATA: WORKING AREA Gtjdpswhzcpjfx Afnou Center height 160 mm Swing over bed 320 mm Swing over cross slide 190 mm Distance between centers 650 mm TURNING SPINDLE Spindle head DIN 55027/DIN ISO 702-3 Gr. 5 Spindle bore 43 mm Spindle diameter in front bearing 70 mm MAIN DRIVE Drive power 60%/100% duty cycle 2.6 / 3.1 kW Speed range 48 – 2,500 rpm Number of speeds 16 FEED RANGE Number 24 Longitudinal 0.02 – 0.63 mm/rev Cross 0.006 – 0.2 mm/rev THREADING RANGE Metric threads 0.25 – 8* mm TAILSTOCK Quill diameter 40 mm Quill stroke 85 mm Internal taper DIN 228 MK 3 ACCEPTANCE ACCURACY DIN 8605 * Inch threads and metric thread pitches 0.45; 0.75; 4.5 and 5.5 are only available with additional change gears. This machine is located in our showroom in 71334 Waiblingen-Beinstein and is available immediately. Please contact us regarding the available options.

Condition: used, Year of construction: 2003, machine/vehicle number: 1527, Used lead and feed screw lathe COLCHESTER Triumph VS 2500 Centre height: 195mm Distance between centers: 650mm Godpfx Aox Hrumofnetu Spindle bore: 54mm Infinitely variable speed: 14–2500 rpm Tailstock quill: MT5, coolant system, quick thread cutting device Digital readout: FAGOR NUP 300 TS-RS 1 x RÖHM 3-jaw chuck, 5-position stop drum, spindle stop, machine lamp, 1 x PARAT 4-way turret, 4 x PARAT tool holders, live centre and quick-action drill chuck. The machine is located at our premises in 71334 Waiblingen-Beinstein and is available immediately. Inspection of the machine is possible by appointment.

Condition: used, Year of construction: 2000, used CONDOR AC, partially overhauled Centre height: 165 mm Between centres: 750 mm Spindle bore: 40 mm Spindle speeds: 22–2,800 rpm, infinitely variable - Quick-change tool post size B - WEILER DZ-V digital readout - Hollow spindle stop - Fixed steady rest - 7 Multifix tool holders - Flat splash guard - Electrically interlocked chuck guard Gsdpfx Afox E Um Nonjtu - Change gears and various soft jaws The machine is partially overhauled: - Bed slide: guideways re-coated and hand-scraped, gibs and lower guide strips adjusted - Cross slide measured and aligned on bed slide; cross slide dovetail guide newly scraped, gibs adjusted and scraped - Top slide newly scraped and gib matched - All measuring scales overhauled and cables replaced The machine is located in our showroom at 71334 Waiblingen-Beinstein and is immediately available. For details on equipment, please contact us.

Condition: used, machine/vehicle number: 11756, second-hand WEILER LZ 280 sliding headstock and sliding headstock lathe center height 125mm center width: 800mm spindle speed approx. 26-2000 rpm 1 x three-jaw lathe chuck Ø 125mm with inner and outer jaws, brand new Multifix size A with 2 interchangeable holders Emergency stop/switch unit, rear chip guard, all change wheels present, drive disk, storage tray, machine light, new socket, 15 collets from Ø 3.5 - 18.5 mm, collet clamping tube, fixed point and MK 2 sleeve for clamping tube, bed stop, chuck protection cover, various turning tools and operating instructions. The machine is located at our premises in 71334 Waiblingen-Beinstein and is available immediately. A viewing of the machine is possible by arrangement. Gtjdpfx Aevd Dbnefnsu

Condition: used, machine/vehicle number: 1717, Used lead and feed screw lathe WEILER PRAKTIKANT Gedeuqb Emspfx Afnstu Centre height: 140 mm Distance between centres: 500 mm Spindle bore: 36 mm Spindle speeds: 42–2,000 rpm Equipped with RSF 3-axis digital readout, 1 pc 3-jaw chuck Ø160 mm, Chuck guard electrically interlocked, With Multifix toolpost size A with 3 holders Lever-operated collet device with 15 collets. The machine is located at our facility in 71334 Waiblingen-Beinstein and is immediately available. Viewing of the machine is possible by prior arrangement.

Condition: good (used), functionality: fully functional, spindle bore: 36 mm, center height: 155 mm, turning length: 800 mm, spindle speed (max.): 2,000 rpm, spindle speed (min.): 25 rpm, Used Weiler Condor lathe, No. 7939, Center height 155mm, Center width 800mm, Spindle speeds 12-2800 rpm, spindle bore 36mm Accessories: 1x RÖHM three-jaw chuck Ø 160mm, Multifix base body size B with 2 inserts, keyless drill chuck, Gedev R Tdxopfx Afnstu live center, and coolant system. The machine is in stock at our facility in 71334 Waiblingen-Beinstein and is available immediately.

Condition: used, empty load weight: 12,360 kg, maximum load weight: 32,640 kg, first registration: 11/2010, next inspection (TÜV): 09/2024, total length: 20,000 mm, total width: 25,500 mm, total height: 7,000 mm, suspension: air, tire size: 245/70 R 17.5 /10mm, wheelbase: 1,035 mm, front tire size: 245/70 R 17.5 /10mm, operation weight: 45,000 kg,

Condition: used, empty load weight: 4,400 kg, maximum load weight: 13,600 kg, first registration: 03/2002, next inspection (TÜV): 05/2024, total length: 9,300 mm, total width: 25,500 mm, total height: 40,000 mm, suspension: air, tire size: 235/70 R 17.5 /10mm, wheelbase: 5,100 mm, front tire size: 235/70 R 17.5 /10mm, operation weight: 18,000 kg,

Condition: used, mileage: 620,454 km, power: 420 kW (571.04 HP), first registration: 06/2011, fuel type: diesel, empty load weight: 10,700 kg, maximum load weight: 7,300 kg, overall weight: 40,000 kg, tire size: 385/55 R 22.5 /5mm, axle configuration: 4x2, wheelbase: 5,500 mm, next inspection (TÜV): 11/2023, driver cabin: sleeper cab, gearing type: automatic, emission class: euro5, suspension: steel-air, number of seats: 2, total length: 9,900 mm, total width: 25,500 mm, total height: 37,000 mm, front tire size: 385/55 R 22.5 /5mm, operation weight: 18,000 kg, Equipment: air conditioning,