Used Spherical Reamer for sale (156)

Condition: used, Year of construction: 2014, Feed direction of the panel: to the right from the operator Maximum edge thickness: 3 mm Minimum workpiece thickness: 8 mm Maximum workpiece thickness: 60 mm Minimum workpiece width: 65 mm Minimum workpiece length: 160 mm Feed speed: 10 m/min Jointing unit: Yes, with 2 milling units Jointing tool: Diamond cutters Diameter: 70 mm Height: 48 mm Infeed fence adjustment: manual Chopping shear up to: 3 mm Single edge feeding: possible Gluing: GlueJet Itjdpfjylpwujx Aa Ijh PU gluing: possible Cross-cut saw: Yes Combination unit for flush/bevel/radius: pneumatically adjustable Corner rounding unit: pneumatically adjustable Profile scraper: yes Flat scraper: yes Aggregate display: on the display Control type: via limit switches Operation: Control panel with buttons Transport device: No Extendable roller support: Yes Protective hood: Yes Working height or feed table height: 874 mm Weight approx.: 1400 kg Extraction diameter: 160 mm Storage location:

Condition: used, Holz Her STREAMER 1057 XL FÜ + PU Edge thickness 0.4 - 6 mm Modern control system with selector switch for adjusting the units Fully automatic edge magazine for roll and strip material GLU-JET adhesive application station, cartridges + PU adhesive Adhesive application using nozzle technology Sensor-controlled nozzle Workpiece height 6-60 mm Automatic adhesive height adjustment Itsdpfezcau Eox Aa Ijh High-quality 3-roller pressure unit, 1st roller motorized Trimming unit, pneumatically controlled for roll and strip material up to 6 mm edge thickness With pneumatic adjustment of the trimming saw angle from 0-10° Routing unit, flush trimming 6 mm, radius routing - chamfer routing - 15° Corner copying unit - 3 mm edge thickness Scraping unit for chamfers and radii with 2 scraping blade holders Surface scraping unit - finishing Buffing unit Spray device in the infeed and outfeed area, as well as for PU Machine with all processing tools Machine is WORKSHOP TESTED From a craft business First delivery 2019 Available from stock in Lieboch

Condition: good (used), Year of construction: 2020, - Used machine - Year of manufacture: 2020 - Edge thickness for rolls: 0.4 - 6 mm - Edge thickness for strips: 0.4 - 6 mm Iedpfxoy U E Tls Aa Ieth - Edge height max. 60 mm - Workpiece length min. 160 mm - Workpiece width min. 60 mm - Feed rate 10 m/min - Edge trimming unit FG201 with 2 diamond cutters - Edge feeder 1903 - Glue application system Glue-Jet GJ301 - Pressing unit 1912-3, pneumatic - Trimming unit 1918, pneumatic - Milling unit FR 201 with 2 diamond cutters - Corner copying unit 1832 with diamond cutter - Pull-blade unit 1929 - Surface pull blade 1964 - Scraping unit 1940 - Spraying system 1856, infeed and outfeed area - Ex works, free loading

Condition: ready for operation (used), Year of construction: 2013, Edgebander manufactured in 2013. This HOLZHER Streamer 1054 features a premilling unit with diamond tools, capable of handling workpiece thicknesses up to 60 mm. It includes a Glu Jet S cartridge system for glue application and a pneumatic end trimming unit. The machine also offers a trimming unit for flush or radius edges, with a radius capability of up to 3 mm and edging thickness up to 6 mm. For more information about this machine, please reach out to us. • Premilling unit: diamond tools Iedpfx Ajy Ddycoa Ijth • Workpiece thickness: up to 60 mm • Glue application: Glu Jet S cartridge system (EVA / PUR) • End trimming unit: pneumatic • Pressure unit: 3 rollers (first roller motor-driven) • Trimming unit: flush / radius • Radius: up to 3 mm • Edging thickness: up to 6 mm • Scraper units: radius scraper (R); flat scraper (glue removal) • Automatic edging feed: coil or strips

Condition: ready for operation (used), Year of construction: 2016, functionality: fully functional, workpiece width (max.): 65 mm, workpiece length (max.): 250 mm, feed rate X-axis: 10 m/min, overall weight: 1,200 kg, TECHNICAL DETAILS Edge band thickness min.: 3 mm Edge band thickness max.: 6 mm Panel thickness min.: 6 mm Panel thickness max.: 45 mm Panel width min.: 65 mm Panel width max.: 65 mm Panel length min.: 160 mm Panel length max.: 250 mm Feed speed min.: 10 m/min Feed speed max.: 10 m/min MACHINE SPECIFICATIONS Dimensions & Weight Itodpfx Aajx Rbm He Ijh Dimensions (L x W x H): 4,630 x 1,600 x 1,770 mm Weight: 1,200 kg Number of transport packages: 1 piece Voltage: 400 V Power consumption: 29.37 A Fuse protection: 35 A EQUIPMENT Pre-milling unit - Type: FG 201 - tools included Glue application unit - Type: 1903 Pressure rollers - Type: 1812 - tools included End trimming unit - Type: 1918 - tools included Rough trimming unit - Type: FR201 - tools included Corner rounding unit - Type: 1832 - tools included Radius scraping unit - Type: 1964 - tools included

Condition: used, Holz Her STREAMER 1057 FÜ + PU Edge thickness: 0.4 - 6 mm Modern control system with selector switch for aggregate adjustment Pre-milling unit for precise workpiece preparation before the gluing section Fully automatic edge magazine for coil and strip materials GLU-JET cartridge adhesive application station + PU gluing Adhesive application via nozzle technology Workpiece height: 6–60 mm Automatic glue height adjustment High-quality 3-roller pressure unit, 1st roller motorized Pneumatic end trimming unit for coil and strip material up to 6 mm edge thickness With pneumatic adjustment for 0–10° inclination of the end saws Milling unit for flush trimming up to 6 mm, radius milling and bevel milling up to 15° Iodpfx Aoyg H Hisa Ieth Corner rounding unit for edges up to 3 mm thickness Scraper unit for bevels and radii, equipped with 2 scraper holders Flat scraper unit for finishing Spraying device – PU Machine equipped with all processing tools Machine is WORKSHOP-TESTED and in TOP CONDITION Available from stock in Lieboch

Condition: good (used), Reamer, twist drill, drill bit Ijdpfx Aaex R Sz Ie Isth -Twist drill: Ø 75 mm -Recording: MK5 -on request: different sizes/quantities available from further stock -Dimensions: Ø 75 x 600 mm -Weight: 8.6 kg

Condition: ready for operation (used), Year of construction: 1996, filling capacity 400 Liter Usable Volume 300 Liter filling amount max. 850 kg workpiece sizes max. 850 x 200 mm Individual weight of workpiece max. 30 kg turning speeds 4.0 - 15.0 U/min Inner drum width 925 mm drive motor 380 V weight of the machine ca. 1950 kg. range L-W-H 3100 x 1600 x 2000 mm good / well-maintained condition (!!) - in checked conditions - machinevideo - ?v=xxnCddCmXe4 Description: - LIMA cleaning machines * for long concrete formwork parts, formwork clamps * for flame-cutting parts, plasma-cutting parts, laser-cutting parts * for punching and sawing parts - environmentally friendly, cost-saving, low-noise - drive with 5-fold V-belt via worm gear - maintenance-free spherical roller bearings - entire machine is highly soundproofed - dust extraction installed as standard - drum running time adjustable - speeds variably adjustable - the drum can be moved into any position using jog mode - space-saving thanks to compact design - extraction system built into the machine - single-lever drum quick release - machine bearings on vibration dampers - spacious unloading area, suitable for Euro standard containers - free access for forklifts or pallet trucks Working method: - the parts to be processed are moved by their own friction . deburred, descaled and derusted. - the closed design reduces the noise generated during deburring . to just 68 - 72 dB(A). - a direct-acting dust extraction system automatically removes . the dust generated during processing. - the machine can also process oily punched and sawn parts. - during this processing, additional sawdust is added to the drum. - a time delay switch switches the dust extraction system on individually. - the parts are thus deoiled and dried first. - only after this process does the dust extraction system switch on . automatically to suck the sawdust out of the drum. - by specifying the drum speed, optimal processing is guaranteed. Itodpfxjzcqzis Aa Ish - the LIMA-400 L deburring machine can be set up anywhere, . provided there is a solid surface/foundation. - after the work is complete, the drum remains in the position. . so that the drum flap can be opened quickly. - one work cycle takes about 20 minutes.

Condition: new, HRB 23072CA/W33 spherical roller bearing , Ø outside: 540 mm , Ø inside: 360 mm , width: 135 mm ,unused in original packaging, 100% functional, scope of delivery according to photos ATTENTION: Please ask separately for costs of packaging and shipping! A Itsdpfx Aaji Ea Rgj Ish

Condition: new, SC Rulmenti SA 23056 MBKW33 spherical roller bearing ,Ø outside: 420 mm , Ø inside: 280 mm , width: 106 mm ,unused in original packaging, 100% functional, scope of delivery according to photos ATTENTION: Please ask for charges for packing and transport separately! ATTENTION: Please enquire for charges for packing and transport separately! Itjdpfji Ec Hpex Aa Ijh

Condition: good (used), Standard holders and accessories, attachment holders, SASSEX spiral drill bits, Sassex spiral drill bits, reaming bits, Sassex reamers, Sassex holders, tool holders, drill bit mounts, twist drills -Manufacturer: Sassex, clip-on holders, 4 pieces -Recording: MK5 -Type/Sizes: see photos -Submission/Price: complete Isdpfx Aszbiq Tja Ieth -Transport dimensions: 530/320/H60 mm -Weight: 18.4 kg

Condition: ready for operation (used), Year of construction: 2015, operating hours: 61,469 h, controller manufacturer: TRUMPF, controller model: TASC 6000, This TRUBEND Cell 5000 with TruBend 5085 extended version (2720 mm x 850 kN) and BendMaster 60 was manufactured in 2015. World's first bending automation with image recognition for maximum flexibility. Sheet metal parts up to 40 kg, 6-axis backgauge sensor technology. Maximum repeat accuracy thanks to angle sensor technology (ACB) in automated operation. It features a stable all-steel frame, electro-hydraulic top drive, and a modern block hydraulic system. The control unit is a TRUMPF TASC 6000 with a 15-inch touchscreen and network capabilities. Ideal for precise bending operations, consider the opportunity to buy this TRUMPF TruBend Cell 5000 press brake. Contact us for more information about this machine. • Machine: TruBend 5085 (2720 mm x 850 kN) with BendMaster 60 • Stable all-steel machine frame • Press beam with spherical bearing and tilt adjustment • Electro-hydraulic top drive with 4-cylinder technology • Generous edge clearance • Flat front covers • Modern block hydraulics • Electronic pressure balance • Measuring system with glass scale and spring compensation • Hydraulic oil in the machine (lifetime lubrication) • Oil cooler • Control cabinet cooling via air-to-air heat exchanger • Modern machine design • Stop/Backgauge • Stop system • Backgauge system: 2 axes (X and R) • Tool clamping • Upper tool holder, manual clamping, hardened • Lower tool holder, hydraulic clamping, hardened • Lower tool shift, 2 positions, pneumatic • Crowning • Manual crowning • Control • TRUMPF TASC 6000 • Graphical workshop programming • Windows XPe (embedded), Pentium 4, 2.8 GHz • 2 GB RAM • 15-inch touchscreen • Network-enabled • Teleservice via modem • Operation • Control panel with LCD keypad and foot switch • Communication rail Iedpfx Aaox Imqle Ieth • Safety • Standard safety devices • BendGuard safety device for upper tools up to 390 mm • CE marking Additional equipment • TRUMPF BendMaster automation (standard features) • Robot/Handling • Stable base and manipulator in die-cast aluminum • Load capacity 60 kg (workpiece plus gripper) • Low-profile welded floor track • Sheet metal sensor for contour detection • Rotary feedthrough for easy gripper change • Gripper coupling on the BendMaster • Sensors for 4-axis backgauge system • Electric drives • Double sheet detection • NC gripper transfer station • Vacuum generation for suction grippers • Control • TRUMPF PC control with operator terminal • Teleservice via modem • Operation via screen, mouse, and keyboard • Safety • Safety fence with access doorWorld's first bending automation with image recognition for maximum flexibility Sheet metal parts up to 40 kg, 6-axis backgauge sensor technologyMaximum repeat accuracy thanks to angle sensor technology (ACB) in automated operationTruBend 5085 (2720 mm x 850 kN) with BendMaster 60

Condition: good (used), Year of construction: 2010, functionality: fully functional, operating hours: 35,295 h, bending force (max.): 230 t, number of axes: 5, Equipment: CE marking, documentation/manual, safety light barrier, Bending length [mm] 3230 Press force [tons] 230 Control system TRUMPF TASC 6000 Operating hours [h] 35295 Hydraulic operation [h] 24098 Standard equipment: Machine - Robust machine frame as a welded construction in all-steel design - Press beam with high bending strength - Spherical bearing of the press beam with press beam inclination - Proportional valve technology and switchable double pump - Modern block hydraulics with control valves mounted on the cylinder - Electronic pressure gauge - Measuring system with centrally mounted glass scales and temperature compensation - Oil cooler - Control cabinet cooling - Modern machine design Back gauge system - Rear back gauge system with 2 axes and rack and pinion drive for the X and R axes - 2 back gauge fingers with secure adjustment from the front Tool clamping - Upper tool clamping system "New Standard Clamping" manual, hardened, self-centering; for vertical tool change - Lower tool clamping with hydraulic clamping, hardened Lower tool displacement - Lower tool displacement programmable (pneumatic, 2 positions) Control - Machine control: TRUMPF TASC 6000 graphical workshop programming - Windows XPe, Pentium 4 with 2.8 GHz clock speed - 2 GB RAM - 15" touch screen - Network enabled - Teleservice via analog telephone connection Operation - Control panel with LCD keypad, foot switch for up, down and emergency stop - Communication bus for the use of ACB angle sensor tools Safety - Safety device: integrated side doors + Rear back gauge system 5 axes (X, X1, R, Z1, Z2) + Upper tool clamping hydraulic + Crown control CNC + BendGuard + Additional foot switch + 2 pcs. support console + 1 pcs. MobileControl + ACB prepared Iodpfx Aasza Eiis Ioth

Condition: used, Year of construction: 1981, machine/vehicle number: 800 02 81 46, type of input current: three-phase, Specialized EDM drill (eroding machine / hole starter EDM machine) Iodpfx Aoy Su Iyea Ijth This machine is primarily used in metalworking as a hole starting EDM machine or for spark eroding the removal of broken tools (such as taps, drills, or reamers) from valuable workpieces. This is done with extreme precision without damaging the surrounding thread or material.

Condition: used, mileage: 12,133 km, power: 125 kW (169.95 HP), first registration: 01/2025, fuel type: diesel, overall weight: 3,250 kg, color: black, gearing type: automatic, emission class: euro6, number of seats: 4, loading space length: 2,030 mm, loading space width: 1,840 mm, loading space height: 350 mm, Equipment: ABS, air conditioning, all wheel drive, central locking, electronic stability program (ESP), navigation system, parking heater, soot filter, Errors and prior sale excepted! Internal number: 1070. GW25PM23499----SPECIAL EQUIPMENT * Comfort Package 1: Inductive charging station for mobile devices - 400-watt inverter - switch panel - 6 switches * Outdoor Package 2: Engine and fuel tank protection, steel - 100% locking rear differential * Programmable auxiliary heater with remote control * Technology Package 68: Adaptive cruise control incl. intelligent speed limiter - Blind spot assist with trailer coverage - 13-pin trailer hitch - Extended lane keeping assist incl. lane departure warning and driver drowsiness alert - Front and rear Park Pilot system - Emergency braking function when reversing out of parking spaces - 360-degree camera with split view technology * 3-way tipper conversion: hot-dip galvanized lightweight steel profiles - fold-down side panels - lashing eyes recessed into the floor frame - 4 spherical tipping bearings with 2 locking pins to determine tipping direction - hydraulic cylinder operable from driver's cab - audible warning signal when the tipping bed is not in the lowered position - LED rear lights FURTHER EQUIPMENT * ABS * Two front tow hooks * All-wheel drive (shiftable four-wheel drive) with electronic gear selection * Trailer preparation kit * Electrically adjustable, heated, and folding exterior mirrors * Battery management system * Light-colored woven fabric headliner * Anti-theft alarm system incl. double locking with interior monitoring * ESP * Electric windows * High beam assist * Ford Key Free system * FordPass Connect incl. eCall and Wi-Fi hotspot * Heated windscreen * Extendable cup holder * Auto-dimming rearview mirror * 8-inch digital instrument cluster * Dual-zone automatic climate control with dust and pollen filter * LED fog lights * LED headlights * Steering wheel: Heated multifunction leather steering wheel * Front center console with integrated armrest * Off-road package: rotary switch drive modes - Terrain Management System with 6 selectable drive modes - off-road SYNC screen Itsdpfjy T Ty Dox Aa Ijh * Wheel package 35: 4 alloy wheels 7.5 J x 18 with 255/65 R 18 all-season tires, Asphalt Black Matte-Silver - 18-inch aluminum spare wheel * Rear seat package 18: two folding emergency seats with two three-point seat belts - seatbelt warning chime front and rear * Safety package 2: Advanced airbag restraint system - front passenger airbag deactivation function - driver front airbag - driver and front passenger seats with reinforced side support - knee airbags for driver and passenger - curtain airbags above the side windows - side airbags for driver and passenger - reinforced body structure - reinforced frame * Seat package 7: driver's seat electrically adjustable in 8 ways including lumbar support - passenger seat manually adjustable in 4 ways - heated driver and passenger seats - map pocket on driver’s seat backrest * Particulate filter: diesel particulate filter (DPF) with SCR catalyst * Upholstery: leather * Pre-Collision Assist including distance indication and warning, forward collision warning, and active emergency braking assist * Audio system 89: Audio system including Ford SYNC 4A, Ford navigation system, AppLink, and 10-inch touchscreen - FM/DAB antenna - 6 speakers - Android Auto and Apple CarPlay - Bluetooth handsfree and audio streaming - digital user manual - steering wheel remote control - Ford Power-Up software updates (over-the-air update) - intelligent pre

Condition: good (used), Year of construction: 2005, functionality: fully functional, pressing force: 320 t, installation height: 615 mm, control type: CNC control, Bending length [mm] 4220.00 Press force [tons] 320 Control unit TRUMPF TASC 6000 Hydraulic hours [h] 53,030 Standard equipment: - Rigid machine frame, all-steel welded construction - Press beam with high bending strength - Spherical mounting of the press beam with beam tilt capability - Electro-hydraulic top drive with 4-cylinder technology - Proportional valve technology and switchable double pump - Modern block hydraulics with control valves mounted on the cylinder - Electronic pressure scale - Measuring system with centrally mounted glass scales and temperature compensation - Manual, integrated wedge crowning in the bed - "New Standard Clamping" manual, hardened, self-centring upper tool clamping system for vertical tool change - Lower tool clamping with hydraulic clamping, hardened - Programmable lower tool displacement (pneumatic, 2 positions) - 2-axis backgauge system with rack-and-pinion drive for X and R axes, 2 stop fingers, safely adjustable from the front - Machine control: TASC 6000 - Operator console with LCD keypad, emergency up, down and E-stop foot switch - Safety features: integrated side doors and automatic rear roller cover - Control cabinet cooling - Oil cooler - Modern machine design + 5-axis backgauge system + Hydraulic upper tool clamping + CNC crowning + BendGuard + 2 support consoles + Park position + 1 bending aid + Additional foot switch Itjdpey Sarqefx Aa Ioh

Condition: good (used), Year of construction: 2010, functionality: fully functional, bending force (max.): 85 t, installation height: 615 mm, number of axes: 6, Equipment: CE marking, documentation/manual, safety light barrier, Bending length [mm] 2720 Press force [t] 85 Control unit TRUMPF TASC 6000 Operating hours [h] 45666 Hydraulics on [h] 13762 - Top drive concept in four-cylinder design Y1/Y2 - Electrohydraulic ram drive with proportional valve technology - Ram position measuring system with deflection compensation via glass scales - Modern block-type hydraulics - Spherical suspension and inclined position of the pressure beam - CNC backgauge system - Safe finger adjustment from the front - 2 stop fingers - Self-centering, manual, hardened upper tool holder for vertical tool change - Hardened, manual lower tool clamping - Program-controlled lower tool displacement (I-axis) for 2 positions - Flat front cover - Modern safety guard - CE mark - Oil cooler clamping device - Increased installation height - 6-axis backgauge - Hydraulic upper tool clamping - Hydraulic lower tool clamping Itjdpfey Saq Tjx Aa Ijh - CNC crowning - CNC I-axis - BendGuard - ACB preparation - 2 support consoles

Condition: excellent (used), Year of construction: 2003, operating hours: 3,800 h, functionality: fully functional, Good morning, I am selling a complete set ready for drilling operations: - Vermeer D7x11a horizontal drill, 2003, ~3800 operating hours. It underwent a major overhaul a few years ago, has almost a full magazine of Hunting drill rods, and is in very good technical and visual condition. - Vermeer mixing unit with a 120 l/min bentonite pump, 2003. Tank capacity: 1200 l. - Iveco Eurocargo 100E18 E5 truck, 2012, ~290,000 km. Equipped with an additional tank (1100 l), shelving, a water transfer pump, a water filling system, a Cintropur filter, tool holders, and a custom-made external aluminum toolbox. Aluminum ramps are also included. The vehicle has undergone a full service at an authorized Iveco workshop. Oils, filters, front and rear brakes, new headlights and windshield, and new batteries have all been replaced. The vehicle is in excellent condition. - An additional D7x11a drill for parts - the machine is practically complete, missing only a few elements and parts. The engine is in working order. Ijdpfszd Ribsx Aa Ijth I will include a starting drill rod, a drilling head, a locking sleeve, and 3 reamers (90-230 mm) with the drill. The set is currently used only occasionally, but it is ready for operation at any time.

Condition: used, functionality: fully functional, Complete valve grinding set for professional engine repair – packaged in three robust transport cases. Includes the actual valve grinding machine, a comprehensive set of valve seat cutters/reamers in various diameters, as well as collets and accessories (see photo – case opened). Ideal for engine repair shops, automotive specialists, boat engine/stationary engine service, classic car restoration, railway workshops, and industrial repair. The complete set is difficult to obtain individually and is therefore highly sought after. According to the equipment list (inventory no. 200004), the manufacturer is EFCO Maschinenbau GmbH, type Valval – please verify this on the nameplate on site. Test run/inspection possible at any time by appointment. Scope of delivery (3 transport cases): 1. Valve grinding machine (actual grinding unit) 2. Valve seat tools/cutter set 3. Collets, reamers, and accessories Technical data: Isdpszachvjfx Aa Ijth - Power supply: 230 V (check on site) - Application: Valve grinding, valve seat machining, valve guide machining - Completeness: apparently complete according to the photo, please check against the original list on site Collection/transport: Self-collection by car/van (3 cases, each approx. 20-30 kg). Shipping via a freight forwarder is possible.

Condition: good (used), Year of construction: 1986, SOE reamer grinding machine with projection measuring device. Accessories: collets, various grinding wheels. In good, operational condition. Itjdpfxjy Tuhvs Aa Ioh

Year of construction: 2010, condition: like new (used), Used Trumpf Trubend Series 3000 CNC pressbrake for sale VIDEO BELOW: Used Trumpf Trubend 3120 for sale 3metre x 120ton 6 axis plus pressbrake for sale. Brand/make: TRUMPF Model: TRUBEND 3120 Type: CNC hydraulic Press Brakes New 2010 Location: United kingdom Low hours – 14,000 Specification Convert Specs to Imperial Tonnage 119.749 t / 120ton Type: hydraulic downstroke Overall Length 3.1 m /3metre BH 2.7 m Stroke 199.9 mm Number of axis: 7 axis 5 axis back gauge Weight 18298 (LBS) Control CNC (T3000) 132 Ton X 10′ Trumpf TruBend 3120 CNC Press Brake Year: 2010 Specification from new: Machine – Stable machine frame as welded all-steel construction – Ram, highly resistant to torsional forces – Spherical ram suspension, with ram tilt Isdpfx Aohtm Ikja Isth – Electro-hydraulic downstroking drive with 4-cylinder technology – Proportional valve technology – Modern block hydraulics – Electronic pressure balance – Measuring system with glass scale and frame deflection compensation – Hydraulic oil filled in the machine (lifetime lubrication) – Oil cooler Backgauge System – Backgauge system 2-axes with rack and pinion-drive for X- and R-axis, – 2 pieces back gauge fingers with safe adjustment in front of the machine Tool Holder – TRUMPF Upper tool clamping, manual and hardened – Lower tool clamping, manual and hardened Crowning – Self-regulating crowning system – Additional hydraulic CNC-crowning Control – Machine control: T3000 colour, DELEM based on Real Time for Windows – USB interfaces for keyboard, mouse, etc. Safety – Footswitch for Emergency up, down and emergency stop – Safety equipment: Side doors and manual shutter roller at the rear Services – Installation, start-up and instruction Options for Backgauge System – Back gauge system 5 axis Options for Tool Holder – Amada US Style fast clamping of upper tool holders (segmented, on entire working length) Options for Safety Device – BendGuard Options for Material Handling – Support bracket (2 pc) Delivery – June 2011 Video below: Used Trumpf V and C series cnc pressbrakes also available in stock for sale. We are always interested in buying used Trumpf pressbrakes and machines such as: TruBend 3066 TruBend 3100 TruBend 3170 TruBend Series 5000 TruBend 5085 Trubend 5130 TruBend Series 7000 TruBend 7050 TruBend 7036 TruBend 7050 TruBend Series 8000 TruBend 8230 Trubend 8400

Condition: good (used), Reamer, twist drill, drill -Twist drills: different sizes on request -different manufacturers -Price: Ø 10 - 30 mm 0.50 EUR/mm (drill Ø 20 mm = 10 EUR net) -Price: Ø 31 - 45 mm 1 EUR/mm (drill Ø 35 mm = 35 EUR net) -Price: Ø 46 - 80 mm 1.60 EUR/mm (drill Ø 50 mm = 80 EUR net) -Two-cutter -Diameter: 10-80mm Itedpfjv H D N Rox Aa Ieh -different lengths -Recordings: MK1 - MK6 -Type: HSS

Condition: used, water tank capacity: 40,000 l, V2A stainless steel tank, upright, wine tank/fruit juice tank, Rieger - used - Volume approx. 40,000 liters Diameter approx. 2,800 mm cyl. Height approx. 5,800 mm Total height approx. 7,400 mm Itedpewlg Dajfx Aa Ioh Weight approx. 1,000 kg Outer surface: marbled Inner surface: 2B=IIIC ground Top end: Torispherical head 2 crane eyes Central threaded weld-on connection DN 100 to DN 40 with threaded connection DN 50 with vent valve DN 50 and check valve DN 50 Sprinkling ring Tank cylinder: Level indicator with bar, scale, and standpipe valve DN 15 Manhole 420x320 mm Test tap DN 15 1 ladder hook at the top Immersion stem sleeve for temperature display Downwardly extending CIP line with vent line DN 40 with connecting thread DN 50 Clear drain with angled seat valve DN 50 Cooling line CIP ball Underbody: Torispherical bottom Floor-mounted bottom bead with DN 50 angled-seat valve, flush with tank wall Floor-mounted outlet with butterfly valve/ball valve/angled-seat valve, DN 50 outlet pipe with flange Five spherical feet, height-adjustable, with washers Otherwise, as per photos

Condition: used, water tank capacity: 20,350 l, Rieger V2A stainless steel vertical wine/fruit juice tank - used - Volume approx. 20,350 liters Diameter approx. 2,000 mm Ijdpfx Aajwlg Hno Ioth cyl. Height approx. 6,000 mm Total height approx. 7,400 mm Outer surface: marbled Inner surface: 2B=IIIC ground Top end: Torispherical head 2 crane eyes Central threaded weld-on socket DN 100 to DN 40 with threaded socket DN 50 with fermentation lock valve DN 50 and check valve DN 50 Sprinkling ring Tank cylinder: Level indicator with bar, scale, and standpipe valve DN 15 Manhole 420x320 mm Test tap DN 15 1 ladder hook at the top Immersion stem sleeve for temperature display Downwardly extending CIP line with vent line DN 40 with connecting thread DN 50 Clear drain with angled seat valve DN 50 Cooling line CIP ball Bottom end: Torispherical head to Front-drawn bottom rim with DN 50 angle seat valve, flush with the tank wall Front-drawn outlet with butterfly valve/ball valve/angle seat valve, DN 50 outlet pipe with flange 4 height-adjustable spherical feet with washers Otherwise, as per photos

Condition: used, water tank capacity: 30,250 l, Upright stainless steel container made of V2A, wine/fruit juice tank with 3 cooling plates, partly with digital temperature measurement - used - Volume approx. 30,250 liters Diameter approx. 2,500 mm Cylindrical Height approx. 5,600 mm Total height approx. 7,200 mm Outer surface: marbled Inner surface: 2B=IIIC ground Top end: Torispherical head 2 crane eyes Threaded weld-on socket DN 100 centrally connected to DN 40 with threaded socket DN 50 with fermentation lock valve DN 50 with check valve DN 50 Sprinkling ring Tank cylinder: Level indicator with bar and scale and standpipe valve DN 15 Manhole 420x320 mm Test tap DN 15 Ladder hook at top Immersion stem sleeve for temperature display Downwardly drawn CIP line with vent line DN 40 with connecting thread DN 50 Clear drain with angled seat valve DN 50 Cooling line CIP ball Bottom end: Itjdpowlg E Rofx Aa Ioh Torispherical head to Front-drawn floor sill with DN 50 angled seat valve and DN 50 outlet pipe with flange 4 spherical feet, height-adjustable, with washers Available quantity: 24 Otherwise, see photos