Used Scraper for sale (727)

Condition: used, Silo discharge Duedpfx Aoiw Iagjfnsn

Condition: used, Wood chip screening plant Chip screening plant Width 1,9m Length 5.3m Height 0.8m 1st grid 40x40mm 2nd grid 15x15xmm Duedpfxjtxblkj Afnen Double scraper for screening system Total length 7.5m (2m straight, 5m upwards) Outer flange width 760x610mm Scraper width 400mm + 250mm Gear motor 4 kW Speed 39 rpm

Year of construction: 2025, condition: new, functionality: fully functional, UMG-110.56 Scraper conveyor is designed for transporting wood waste after processing. The conveyor works at an angle. The conveyor is anchored to the base during installation. The speed of the chain and scrapers can be set with a speed regulator, the design speed is 15m/min at 50Hz. The length and height can be adjusted according to your needs. Dedpswdgfuofx Afnjun

Condition: ready for operation (used), Year of construction: 2019, operating hours: 336 h, functionality: fully functional, total length: 4,764 mm, edge thickness (max.): 8 mm, overall weight: 1,840 kg, controller model: Maestro Pro Edge, Edge banding machine with only 336 operating hours & comprehensive accessories! TECHNICAL DETAILS Max. edge thickness: 8 mm MACHINE DETAILS Control: Maestro Pro Edge Electrical Data Voltage: 400 Volt Frequency: 50 Hz Dimensions & Weight Machine length: 4,764 mm Weight approx.: 1,840 kg Operating hours: 336 h Edge Banding Machine Configuration: Flush trimming and scraper unit, radius: 1 mm Flush trimming and scraper unit, radius: 2 mm Spraying unit for edge finishing Spraying unit for delicate edges Surface scraper "RC-V" Brushing unit "SP-V" Dusdpfx Asydc Abofnjn "SAVENERGY" kit "EASY SIZE" device Internal lighting for the enclosure and gluing area Ceramic lamp with infrared rays Electronic positioning of the pressure rollers Spare adhesive tank "SGP" with NC dosing system Additional adhesive tank "SGP" with NC dosing system Manual feed "Nesting" tracing rollers Diamond tools H=64 for pre-milling unit, 2 teeth Base

Condition: ready for operation (used), functionality: fully functional, feed rate X-axis: 12 m/min, edge thickness (max.): 10 mm, overall weight: 1,530 kg, rotational speed (max.): 12,000 rpm, tool diameter: 80 mm, TECHNICAL DETAILS Panel height: 1,060 mm Maximum edge thickness: 10 mm Minimum panel length: 140 mm Minimum panel width: 85 mm Feed speed: 12 m/min Sanding Unit Motor power: 2.4 HP Speed: 12,000 rpm Tool diameter: 80 mm Extraction port diameter: 60 mm Djdpfx Afsyf Ed Renoun Gluing Unit Glue pot capacity: 2 kg Glue application roller diameter: 25 mm Pressure roller cutter, large roller diameter: 100 mm Pressure roller cutter, small roller diameter: 80 mm End Trimming Unit Motor power: 1.07 HP Maximum tool diameter: 140 mm Extraction port diameter: 80 mm Milling Unit Motor power: 0.87 HP Tool diameter: 70 mm Extraction port diameter: 80 mm Scraper Unit Extraction port diameter: 60 mm Joint Scraper Unit Extraction port diameter: 60 mm MACHINE DETAILS Compressed air connection: 7 bar Dimensions & Weight Dimensions (L x W x H): 3,900 x 1,000 x 1,600 mm Weight: 1,530 kg EQUIPMENT Electronic control panel with USB port Sintra software Touch probe devices Vertical and front touch probe devices with rotating discs Removable panel support arm

Condition: ready for operation (used), Year of construction: 2007, functionality: fully functional, machine/vehicle number: 0-201-09-5124, travel distance X-axis: 6,000 mm, travel distance Y-axis: 1,650 mm, controller model: Homatic PC 85 Power Control, TECHNICAL DETAILS X-axis working range: 6,000 mm Y-axis working range: 1,650 mm – up to 1,750 mm for milling Max. travel height during edge banding: 60 mm Max. applicable edge height: 65 mm Minimum internal radius: 30 mm Automatic tool changer: 18 positions Drilling head: 27 spindles (4 kW) Max. unit saw blade diameter: 200 mm MACHINE DETAILS Control system: Homatic PC 85 Power Control Software: WoodWop Electrospindle C Vector: 11 kW, HSK F63 Edge specification: Rolls, PVC / ABS 0.4 - 3 mm EQUIPMENT 10 adjustable support rails for vacuum cups Loading and unloading aid with 8 pneumatic rods Vacuum cup positioning with laser system Edge banding unit with 360° rotation, glue pot, and preheater for granular EVA glue Rubber-coated pressure roller + Rubber-coated pressure roller Preheating lamp Edge trimmer and edge scraper Dodeydl Nwjpfx Afnjun Edge holder magazine Front and side safety system with carpets Protective cage around access area Chip extraction with motorized conveyor belt Air conditioning for machine control cabinet Automatic lubrication system Vacuum pump

Condition: ready for operation (used), Year of construction: 2010, functionality: fully functional, machine/vehicle number: 0-261-04-5659, feed rate X-axis: 14 m/min, workpiece height (max.): 60 mm, controller model: Power Control Check 20+, grinding spindle motor power: 2,200 W, TECHNICAL DETAILS Panel height: 8 - 60 mm PVC/ABS thickness: 3 mm Pre-scoring depth for wood: up to 8 mm Feed speed: 8 - 14 m/min MACHINE DETAILS Control unit: Power Control Check 20+ Output per sanding motor: 2.2 kW Supply voltage: 400Y/230 V Phases: 3 Frequency: 50 Hz Full load operating current: max. 23 A Largest motor: 4.5 A Dujdpfxsydim To Afnen Largest heating circuit: 3.1 A EQUIPMENT Electrically adjustable working length via CNC Lateral roller conveyor with idler rollers for panel support Coil holder plate Gluing unit for EVA adhesive with pre-filler and glue tank Edge pressure unit for straight profiles, with CNC-adjustable pressure rollers Indexing group with automatic tilt adjustment Overlapping milling unit with 2 motors Rounding unit with 2 multifunction motors (chamfering + rounding) with CNC automatic adjustment Edge scraper unit Glue scraper unit Brush unit

Condition: ready for operation (used), Year of construction: 2011, functionality: fully functional, machine/vehicle number: 0-261-20-5976, feed rate X-axis: 20 m/min, workpiece height (max.): 60 mm, controller model: POWER CONTROL PC 20+, TECHNICAL DETAILS Panel height: 60 mm PVC-ABS edge thickness: 3 mm Solid wood edge thickness: 12 mm Feed speed: 20 m/min MACHINE DETAILS Control system: POWER CONTROL PC 20+ Operating current at full load: max. 33 A Largest motor: 9.7 A Largest heating circuit: 2.7 A Fuse: 35 A Frequency: 50 Hz EQUIPMENT Upper motorized rubberized belt Manual infeed guide Anti-adhesive unit Jointing unit Gluing with EVA adhesive Edge support plate End trimming unit with automatic tilt adjustment Offset trimming and corner rounding unit with two motors Linear corner rounding unit with 2 motors Edge scraper unit Dsdpfx Aoydihdsfnjun Glue scraper unit Brushing unit

Condition: ready for operation (used), Year of construction: 2008, functionality: fully functional, machine/vehicle number: 77503, feed rate X-axis: 25 m/min, workpiece height (max.): 60 mm, overall weight: 6,510 kg, controller manufacturer: SINTRA, TECHNICAL DETAILS Panel height: 60 mm Solid wood: 20 mm PVC / ABS: 3 mm Max. feed speed: 25 m/min Duedpsydidrsfx Afnon MACHINE DETAILS Control: Sintra Weight: 6,510 kg EQUIPMENT - Sanding unit - Coil holder magazine with 2 positions and automatic edge change via CNC - Adhesive unit for EVA hot-melt glue with preheating device and glue pot - Preparation for adhesive unit for PUR glue - Pressure group for straight profiles with electronically adjustable pressure rollers via CNC - End trimming unit with 2 motors and automatic tilt adjustment - Filler unit with 2 vertically aligned motors - Edge smoothing unit with 2 swivelling motors - Multifunctional 4-motor corner rounding unit (smoother + corner rounder) with numerical control in automatic adaptation - Anti-stick unit - Adjustable edge scraper unit - Glue-saving unit - Oscillating brush unit - Electronically adjustable working height - Motorized rubber belt with increased pressure - Motorized and electronically adjustable panel guide - Side roller conveyor with idler rollers for panel support

Condition: ready for operation (used), Year of construction: 2009, functionality: fully functional, machine/vehicle number: H/32059, feed rate X-axis: 22 m/min, workpiece height (max.): 50 mm, TECHNICAL DETAILS Panel height: 10 mm to 50 mm Solid wood: 12 mm PVC/ABS: 0.4 mm to 3 mm Max. feed speed: 22 m/min Min. panel length: 150 mm Min. panel width: 70 mm MACHINE DETAILS Rectifier group motors: 1.5 kW (2 motors) EQUIPMENT Touchscreen control for adjusting working units Panel support guide Dusdpfx Afeydibwonen Side roller conveyor with idler wheels for panel support Anti-adhesive unit Roll holder plate COMBIMELT glue unit for hotmelt adhesive with automatic VarioMelt dosing and pre-melter Patented edge pressing unit with segmented pads Trimming unit with 2 motors Cleaning unit with 2 motors Rounding unit Edge scraper unit Working height adjustable electronically via C.N. Powered rubberized conveyor with top pressure

Condition: new, Year of construction: 2007, functionality: fully functional, machine/vehicle number: 0711ST0619, feed rate X-axis: 13 m/min, rotational speed (max.): 12,000 rpm, Dismantling and loading can be handled by the seller! Auction of an unused Format 4 Felder Perfect 40! TECHNICAL DETAILS Feed rate: 13 m/min Maximum material thickness: 3 mm Dedpfx Aoyddmnsfneun Main trim saw motor power: 0.5 kW Main trim saw motor speed: 12,000 rpm Trimming and profile unit motor power: 0.68 kW Trimming and profile unit motor speed: 12,000 rpm Polishing unit motor speed: 1,400 rpm MACHINE DETAILS Electrical data Voltage: 400 V Phases: 3N Frequency: 50 Hz Power: 8 kW EQUIPMENT Guillotine for edging material up to 3 mm Teflon-coated glue pot for 3 kg EVA granulate Audio generator Glue roller with quick-change system Pneumatic pressure unit, 1 driven and 2 conical pressure rollers End trim saws with carbide-tipped blades Z = 24, d-100 x 20 x 3.2 mm Trimming and profiling unit with foldable option up to 15° Edge scraper for R = 2 mm Polishing unit with 2 motors

Condition: new, Year of construction: 2008, functionality: fully functional, feed rate X-axis: 9 m/min, workpiece height (max.): 60 mm, overall weight: 750 kg, rotational speed (max.): 12,000 rpm, Dismantling and loading can be handled by the seller! Auction of an unused Felder G 500! TECHNICAL DETAILS Edge thickness: 0.4-5 mm Workpiece height: 8-60 mm Feed speed: 9 m/min Dusdjyddgzjpfx Afnjn Spindle speed of milling unit: 12,000 rpm Minimum workpiece width: 70 mm Minimum workpiece length: 140 mm Radius scraper unit: R = 2 mm Polishing unit: 2 motors at 1,400 rpm MACHINE DETAILS Dimensions & Weight Dimensions (L x W x H): 3,200 x 1,100 x 1,550 mm Weight: 750 kg FEATURES High-performance chain feed Support for coiled edge material Guillotine blades for cutting coiled edges up to 3 mm Glue roller for EVA granulate from the Teflon-coated glue pot Spring-loaded pressure unit with 1 rubber pressure roller and 2 drive rollers Milling unit 0.27 kW, 100-tooth 24-tooth saw blade

Condition: not inspected (used), Year of construction: 2009, operating hours: 29,000 h, functionality: unexamined, feed rate X-axis: 25 m/min, total length: 7,755 mm, workpiece height (max.): 40 mm, working height: 950 mm, controller model: PowerControl PC22, TECHNICAL DETAILS Feed rate: 18 - 25 m/min Maximum feed rate with FK11: 20 m/min Working height: 950 mm Minimum workpiece width (for workpiece thickness 12-22 mm): 60 mm (depending on workpiece length) Minimum workpiece width (for workpiece thickness 23-40 mm): 105 mm (depending on workpiece length) Workpiece protrusion: 30 mm Workpiece thickness: 12 - 40 mm Edging material (coil): 0.3 - 3 mm Maximum edge cross-section (PVC): 135 mm² Maximum edge cross-section (veneer): 100 mm² Maximum coil diameter: 830 mm Edging material (strips): 0.4 - 20 mm Maximum edge cross-section (strips): 900 mm² MACHINE DETAILS Control system: PowerControl PC22 Pneumatic connection: 7 - 8 bar Total length: 7,755 mm Operating hours: approx. 29,000 h EQUIPMENT Workpiece support with scissor-design and roller support, extendable to 1000 mm Automatic infeed guide adjustment Fixed stops on left side Pneumatically controlled infeed lock Top pressure via driven composite V-belt Duedoyc S Hajpfx Afnjn Electrical height adjustment Workpiece transport unit via transport chain with rubber coating Separating agent spray unit, top/bottom Joint trimming unit 2 x 3 kW Gluing unit A20 with 2 rollers, comprising workpiece preheating, Quickmelt application unit with quick-clamping system, 2-roller magazine, pressure zone C (automatically adjustable with 1 pre-press roller and 6 post-press rollers) Trimming unit HL84 0.8 kW, with automatic chamfer/straight adjustment and pneumatic flush/excess trimming adjustment Pre-milling unit 1.5 kW, pneumatic adjustment between flush and excess milling Contour milling unit FK11 with automatic adjustment from chamfer to radius milling Profile scraper PN10 (with pneumatic side retraction) Finishing unit (with pneumatic side retraction), consisting of glue joint scraper and buffing unit Remote control Workpiece guide for FK device Note: Container loading and seaworthy packaging by the seller is not possible.

Year of construction: 2008, condition: good (used), Anko BFK-10 Automatic stir fryer Capacity 60l, gas LPG, with a scraper and stirrer to scrape liquid eggs and stir fry ingredients, automatic temp control, variable speed, automatic tip discharge, suitable for cooking fried rice, fried noodle, dried meat cracker, dried meat floss, jerky, fried ground meat, ham, dried squid, steak, coffee, peanut, powder, bean, sugar coating, tea leaf, sesame, tofu, sticky rice and more, 3Ph Duedpfx Ash N Slxjfnon

Condition: used, These Scrape Surface Heat Exchangers can be used on various products for heating process such as Tomato pastes, custards, margarines, oils, mayonnaise, etc. We have fully refurbished these units by changing internal gaskets, rings, sand blasting , paint job, new stainless steel frame , new controls and motor test and service . Technical Details of VOTATOR - Make: A. Johnson & Co London - Year of Refurbishment: 2025 - Quantity: 5 units - Diameter: 6 inches - Metals: Grade 316 Stainless Steel - Usage: Horizontal Votators Specifications: - Chamber Dimensions:6" Diameter Stainless Steel Chamber - Length: 6' - 1 1/2" between end plates - Rotating Centre:4 3/4" Diameter Stainless Steel - Equipped with two PTFE scraper blades - Drive:11 kW Motor Drives - Speed: 1470 rpm (through a V-belt reduction) - Reducer:Giving a shaft speed of approximately 367 RPM. Availability: - Location: In stock Dujdpfxoygh Egs Afnen - Available: Immediately General Capacity Estimation Formula: For a VOTATOR, the capacity can roughly be estimated using the following formula: [ \text{Capacity} = \text{Chamber Volume} \times \text{Turnover Rate} ] Step 1: Calculate the Chamber Volume The volume of a cylindrical chamber can be calculated as: [ V = \pi \times r^2 \times h ] Where: - ( r ) = radius (half of diameter in inches), - ( h ) = height (length of the chamber in inches). Given: - Diameter = 6 inches, so radius ( r = \frac{6}{2} = 3 ) inches. - Length ( h = 6 \text{ ft} = 72 \text{ inches} ). Calculating the volume: [ V = \pi \times (3)^2 \times 72 \approx \pi \times 9 \times 72 \approx 2036.75 \text{ cubic inches} ] To convert cubic inches to liters (since 1 cubic inch = 0.0163871 liters): [ V \approx 2036.75 \times 0.0163871 \approx 33.39 \text{ liters} ] Step 2: Estimate Turnover Rate The turnover rate depends on the speed of the VOTATOR and how many times the contents of the chamber can be processed. Given the shaft speed is approximately 367 RPM, you might assume a turnover rate of about 1 turnover per minute for a basic estimate. Final Capacity Estimate Assuming 1 turnover per minute: [ \text{Capacity} \approx 33.39 \text{ liters/min} ] Conclusion The estimated capacity of each VOTATOR is approximately 33.39 liters per minute Capacity Calculation: - Estimated Capacity: 33.39 liters/minute Convert to Liters per Hour: [ \text{Capacity per hour} = 33.39 , \text{liters/min} \times 60 , \text{min/hour} ] [ \text{Capacity per hour} \approx 2003.4 , \text{liters/hour} ] Conclusion The estimated capacity of each VOTATOR is approximately 2003.4 liters per hour.

Condition: used, Year of construction: 2021, Manufacturer : Brouillon Process Model: 884-H-EAU Year : 2021 Type : Off-axis tilting cooking vessel Dusdeygncljpfx Afnsn   Useful capacity : 400 L Material : 304 L stainless steel Diameter : 884 mm Operating pressure : 6 bar Maximum temperature: 110°C Double jacket volume: 32.5 L Mixer: 2 stainless steel anchors, each fitted with an inclined PTFE scraper Speed: 7 - 25 rpm Recycling loop on the double jacket for temperature control Flush drain valve at SMS76 outlet, electro-pneumatically controlled Stop cooking function / mains water cooling Total empty weight: 1200 kg

Condition: used, Year of construction: 1969, Mixing: 1 planetary paddle, 1 bottom scraper, 1 side scraper Capicty : 200 Kg.   Vessel : Material : stainless steel Total volume: 389 L Capacity: 200 L Maximum pressure: 0.4 bar Tilting: yes Jacketed : Maximum pressure: 6 bar Electric heating + recirculation pump: 2 x 9 KW   Light for porthole Electrical cabinet   Machine dimensions: 140 x 195 x 240 cm Weight: Approximately 800 kg Dedpjygba Dsfx Afnjun Videos available on request  

Condition: used, Mixing: 1 planetary paddle, 1 bottom scraper, 1 side scraper Possibility of integrating a lateral rotor/stator agitator (this request may be subject to an additional quotation). Side scraper and its support not available (this request may be subject to an additional quotation). Vessel : Material : stainless steel Total volume : 400 L Maximum pressure: 0.4 bar Duodsyfw Inspfx Afnon Tilting: yes Spray nozzle circuit Jacketed : Capacity : 30 L Maximum pressure: 6 bar   Electrical cabinet Machine dimension : 140 x 165 x 240 cm Videos available on request

Condition: used, Year of construction: 2022, operating hours: 4,240 h, functionality: fully functional, Basic Package AK565: Central axle trailer chassis with 2 axles, road approval for 80 km/h Brake system incl. ABS and lighting according to EC directive 50 mm EC drawbar eye incl. slip-on coupling Tyres: 385/65 R22.5 Hydraulically adjustable support leg Splash guards (inner and side-mounted fenders) Permissible total weight: 19,000 kg MTU diesel engine 6R1300, 390 kW at 2,000 rpm, complies with EUROMOT V emission standard Exhaust discharged upwards Load-dependent material feed control incl. automatic reversing of scraper floor Fuel tank, 450 L Feed roller: length 1,690 mm, diameter 510 mm, fitted with bolt-on tooth segments Four-row flail drum with 36 free-swinging cast steel flail holders and replaceable flail tips - Dopplock system Standard: Flail tip “Streusel plus” Centrally arranged lubrication strips Electric pump for operating cylinder functions (e.g. raising/lowering the support leg and opening/closing the rear basket, folding/unfolding the rear conveyor, releasing the drive) when engine is stationary 24 V electrical control system Separate control panel at the rear of the machine Hydraulically folding fine shredding basket “Multimesh” (mesh sizes between 30 - 280 mm, gradations on request) incl. one-piece rear flap Scraper floor with 32 slats Duodpoyhckmsfx Afnjn Chain drive for feed roller and scraper floor Complete radio remote control Drive preparation Rear discharge conveyor, 4 m long, 1,800 mm wide “classic” Anti-magnetic centre section on the discharge conveyor Reinforcement plates (Hardox) on both sides of feed hopper sidewall Fire extinguisher Acoustic start-up warning Doppstadt telematics system Finish: RAL2011 deep orange Optional Equipment: Hydraulic drive 600 L fuel tank Flail tip C1 “Bear Paw” with carbide insert Rear discharge conveyor 4 m, belt width 1,800 mm, lowerable Neodymium magnetic pulley incl. chute Separate drive for feed roller and scraper floor (“Twin Drive”) Duomatic coupling Smooth impact plate Fine shredding basket Delivery date by arrangement

Condition: used, - Model: PLT-C - Capacity: 300 kg (for dough with a water absorption rate of 65%) - Hydraulic bowl lifting - 2 removable bowls - With programmable touchscreen control panel - Serial number: 4945 - Manufacturing date: June 15, 2009 - Weight: 1900 kg - Installed power: 25 kW - Current: 31 A - Frequency: 50 Hz - Auxiliary control: 24 V - Voltage: 400 V - Two inverters for independent control of the scraper and tools - Tool rotation and reverse rotation - Fast incorporation and gentle distribution of inclusions - Patented oil-free planetary tool drive system - Wide selection of quick-release mixing utensils designed for a variety of dough types and preparations - Option for intensive mixing under pressure for uniform and optimal product aeration - Available with double-jacketed bowl for water and/or steam heating/cooling Duodsyg Ehrjpfx Afnen

Condition: excellent (used), 5-Axis Machining Center with swivel milling head, pallet station, tool calibration, thermal compensation, work area extraction system, and much more. Year of manufacture: 2016 Spindle hours approx. 1,500 h (after spindle replacement at the beginning of 2025) Control System: - Heidenhain iTNC 530 HSCI - Heidenhain DCM Collision Monitoring - Heidenhain HR 410 electronic handwheel - Swiveling console with 19" monitor - Teleservice via LAN/WLAN Travel Range: - Travel X 1,000 mm, Y 1,100 mm, Z 810 mm - NC rotary table D 1,000 x 800 mm, swing diameter 1,350 mm Milling Head: - Automatic horizontal/vertical swivel milling head - Fully-fledged stepless NC axis from -1° to +90° Duodpfexhg Disx Afnjn - Blowing air through the spindle - External coolant supply via nozzle ring Drive power: 38 kW (100% duty cycle) Speed: 16,000 rpm Torque: 135 Nm at 40% duty cycle Spindle interface: HSK 63-A Media Supply: - Internal coolant feed: 50 bar - capacity 28 l/min - Paper belt filter with additional fine filter - Individual tool pressure regulation during program operation Tool Changer: - Rack magazine with 73 stations (expandable with additional racks) - Swiveling dialog operation panel - Drawer for loading and unloading tools from tool racks Tool Measurement: - 3D wireless touch probe m&h 20.00-Multi, software adapted for HSK 63-A - Including Kinematics-Opt, compatible with iTNC control, and calibration sphere on magnetic stand Pallet Changer: - Double palletizing unit, pallet diameter 1,000 x 800 mm, hole grid 100mm x 100mm, hardened drill bushes D 16mm - Rotary table unit including zero-point clamping system, loading station accessible by crane - Pallet changer unit protected with enclosure Special Equipment: - Micro-Epsilon sensor - For detection and dynamic compensation of thermal spindle growth Chip Conveyor: - Scraper belt conveyor along machine bed - Chip ejection height 1,100 mm Machine Enclosure: - Full-area protective enclosure with large angle door for crane loading and a quick-access door - Easy removal of swarf from the workspace Extraction System: - Oil and emulsion mist extraction, mechanical air filter, extraction capacity 1,800 m³/h Rotating View Window: - Viewing window integrated into the cabin door for workspace observation Camera in Work Area: - Monitor and keyboard at the operator console—allows monitoring of rear-side machining operations Machine Data: - Space requirement (without service area): approx. LxWxH 4,791 mm x 4,100 mm x 4,791 mm (including extraction system) - Machine weight approx. 19,700 kg - Total weight with all equipment plus maximum workpiece load, full tool magazine, and all operating materials: approx. 27,730 kg - Connected load: 50 kVA, 400V, 50/60 Hz This machining center, featuring an exceptionally good and practical configuration, is in very good condition. It operates with the renowned "Swiss precision." There is no service or repair backlog—in fact, the opposite. With an almost new milling spindle, the REIDEN RX 10 5X is well positioned for long-term use. Technical modifications and errors excepted.

Year of construction: 2023, condition: used, Case maker Kolbus DA 370 Year: 2023 New generation of casemaker for faster production and shorter make-ready times. Automatic production of book cases, files, display cards, calendar backs or game boards, at rates of up to 65 cycles/min. Maximum production and process reliability in the manufacture of book cases. The DA 370 casemaker is a versatile machine for a wide range of applications. The machine with its non-stop case feeder is engineered to be ergonomic and extremely operator-friendly so that it can be easily operated by one person. Configuration: - Copilot system with touchscreen - sectional touch panel for direct operation - large display for showing the speed and malfunction messages - board prestacking conveyor to automatically reload the magazines (stream cover and stack feeder) - counter-stacker delivery with roller conveyor delivery incl. table - cloth feeder for non-stop operation with stack magazine - missing product check during separation of cloth and cardboard - cloth cylinder with grippers and interchangeable plates for rubber pads (5 plates 500 mm wide and 5 plates 720 mm wide, incl. 10 rubber pads) - cardboard centre strip magazine - device used to prepare centre strip roll - centre strip waste chopper - centre strip rub-down unit (head and foot) - rub-down unit used to bond the covering material to cardboards and spine strip without creases - extendable gluing station for processing hot glue with glue preparation in the premelter, heated glue roller and scraper roller - viscosity control unit for an automatic supply of water via a water container with a pump Dodpsydc A Ijfx Afnoun - device for padded cases - function used to request individual cases for monitoring purposes on the operating side - servo-controlled drive technology based on Siemens technology Special equipment: - device for producing quarter-bound cases in two operating steps - device for small format - device for large format - Remote Service Gateway Technical specifications: - Mechanical speed: up to 65 cycles/min - Open cover size max.: 205 x 670 mm - Joint width: 4 - 15 mm - Spine width: 14 - 120 mm - Turn in width open: up to 19 mm - Cloth width: 223 - 708 mm - Cloth height: 158 - 428 mm - Board thickness: 1 - 4 mm - Board width: 95 - 328 mm - Board height: 140 - 390 mm - Board centre strip thickness: 1 - 4 mm - Board centre strip width: 6 - 90 mm - Centre strip roll thickness: 0,3 - 0,6 mm - Centre strip roll width: 6 - 90 mm - Lining width: 195 - 670 mm - Lining height: 130 - 390 mm

Condition: new, Year of construction: 2026, functionality: fully functional, machine/vehicle number: 2026, warranty duration: 12 months, input voltage: 400 V, DGUV certified until: 03/2028, total length: 2,100 mm, total width: 1,100 mm, input frequency: 50 Hz, type of input current: three-phase, electrical fuse: 32 A, Spiral kneader / mixer Model: SP 220 MS LED control with temperature display / temperature control with rewind key Dough machine with 2 timers Tool speed adjustable for min / max. 10 - 220 kg of dough Flour dust hood and bowl scraper 2 tank wagons (340 liters) Standing machine with changing tools Stainless steel tools: kneading spiral, flat beater, whisk DGUV V3-tested Connection 400V, 13.6 kW, 50A 32A-CEE plug Dimensions: 1100 x 2100 x 1500 / 2300mm, WxDxH NEW machine With a 12 month warranty Dedpfx Afof Etm Nsnjun Come to our sales center with baking equipment and many bakery machines.

Condition: used, Year of construction: 2010, Used machine Year of manufacture 2010 With joining unit and corner rounding unit Control panel with LCD display and keypad Joining unit with 2 counter-rotating diamond cutters With edge feeder for roll and strip material With glue roller and glue unit With pre-trimming from the roll With pressure unit Dujdpow I H Rkjfx Afnon With trimming unit with pulling trimming cut With flush and radius trimming unit Corner rounding unit for front edges Manual unit adjustment Edge thickness 0.4-5 mm Workpiece height 8-60 mm Min. workpiece width 70 mm Min. workpiece length 140 mm Feed speed 11 m/min With radius scraper unit With flat scraper With polishing unit Extendable workpiece support Extraction connection 120 + 2 x 80 mm Weight approx. 990 kg L x W x H 4550 x 1550 x 1100 mm Availability: Short-term Storage location: Flörsheim

Condition: good (used), Year of construction: 2005, functionality: fully functional, Single-sided edge banding machine with jointing cutters and coping unit, designed for processing EVA hot-melt adhesives Technical data: Edge thickness: 0.4 - 12 mm Workpiece thickness: 8 - 60 mm Coil separation: 3 x 45 mm or 0.8 x 65 mm Dodpfx Afoygg Nkeneun Machine length: approx. 6,860 mm Top pressure manually height-adjustable Equipment: Manually adjustable infeed fence Jointing unit with 2 motors, 2.2 kW (each) both motors pneumatically controlled Hot-melt adhesive application Pressure zone with 1 primary pressure roller and 3 subsequent pressure rollers End trimming unit with 2 motors, each 0.35 kW automatically adjustable via program from chamfered to straight trim cuts Edge trimming unit with 2 motors, each 0.55 kW, for flush trimming, chamfer trimming, or radius trimming with 4-position fixed-point adjustment for side tracing Grooving unit with horizontal shaft, e.g., for back panel grooves Copy milling unit with 2 motors, each 0.35 kW Pneumatic infeed and outfeed control Profile scraping unit with pneumatic infeed/outfeed control Flat scraper unit Buffing unit Additional equipment: * Release agent application at infeed Control system PC 16 with color graphic user interface Attached return system LIGMATECH BOOMERANG ZHR 11 Return system currently not operational, in need of repair