Used Plaster Worm for sale (368)

Year of construction: 1940, condition: used, Automatic universal hobbing machine for the production of spur gears worm gears Largest milling diameter 120 mm Bodpfxjkw T Rmj Abbelr Smallest milling diameter 5 mm Smallest tooth pitch module 0,30 Largest tooth pitch 2 mm largest milling length 100 mm with all accessories

Condition: refurbished (used), Year of construction: 2008, functionality: fully functional, machine/vehicle number: 647-230, Lid Punching machine without tools Type Hamba 647-230 foil width - 230 mm Blodpoxqg T Nofx Abbsr very good condition - with used embossing calender for worm structure - Power connection: 220/380V - three phases - Additional punching tools available - e.g. 1x 2-fold tool - diameter 80.50mm 2x 2-fold tool - diameter 75.50mm 1x 2-fold tool - diameter 59.54mm 1x 2-fold tool - diameter 93.80x120.90mm

Condition: used, Pay-off and take-up decoiler for coil material WANZKE CAMU Type SC 515/M Serial no. 8487 Year of manufacture: 2006 Coil weight approx. 1,500 kg Maximum coil width: 600 mm Coil inner diameter: 370 - 640 mm Maximum coil outer diameter: 1,800 mm Mandrel shaft diameter: 90 mm Distance from mandrel crown center to mandrel base: 950 mm Mandrel crown speed: 13 rpm Motor speed: 920 rpm Gearbox transmission ratio: 1:70 Mandrel drive motor power: 1.1 kW Power supply: 400 Volt, 50 Hz - Mechanical expansion of the mandrel crown with hand crank - Drive via geared motor with worm gearbox, directly mounted on the mandrel shaft - Geared motor with electric brake - Mandrel shaft with mechanical slip clutch, pre-tensioned and adjustable via disc springs Bsdswvv Rqepfx Abbelr - Mandrel crown without strip travel arms - Without electrical control system and without loop switch Space requirement (L x W x H): 1300 x 800 x 1230 mm Weight: 380 kg Good condition

Condition: excellent (used), max. wheel diameter 400 mm gear width 400 mm max. module 15 min. module 0,5 Control Klingelnberg workpiece weight 300 kg Bsdpfexqrhxsx Abbslr ical angle 0 - 90 ° centre distance 15 - mm weight of the machine ca. 1,9 t dimensions of the machine ca. 2,3 x 1,8 x 2,4 m Fully automatic CNC-controlled gear measuring center for spur gears and other gears depending on the software. Equipment for internal gears. Software: - Spur gear, hob measuring, worm checking

Condition: like new (used), input voltage: 400 V, The EVO model spiral mixer features a heavy-gauge painted steel sheet construction, a hydraulic system with lifting rams for the head, and a carriage release mechanism. The machine head is equipped with an exclusive hydraulic lifting device that, during mixing operations, neutralizes and protects it from stresses transmitted by the mixing tool. It is equipped with a spiral tool rotation via belts driven by a high-power motor. The bowl drive is provided by an independent motor, using high-performance belts and a worm gear reducer in an oil bath. The mixer offers two spiral rotation speeds, with mixing times set via a dual timer (one for each speed). Switching from low to high mixing speed and stopping the machine are carried out automatically. The carriage is automatically locked using a self-centering system. Bodsxz D Sdepfx Abbelr Finally, there are patented head lifting/lowering controls located on the carriage.

Condition: as good as new (ex-display), centre height 130 mm spindle bore 18 mm ratio 40:1 swivellable - 10° bis 90° ° groove width 16 / 18 mm weight 35 kg dimensions of the machine ca. 0,5 x 0,25 x 0,25 m Unused semi-universal dividing set: - Spindle in precision tapered roller bearings - Phosphor bronze worm wheel, helix Cr-NI steel, hardened and ground - Translation disengageable for direct sharing - each division 2 to 50 and many divisions to 380 accessories: Tailstock, 2 part washers, centering point, driver and chuck flange Bedpfx Absuvd Axsbelr Machine dealer with own stock of 1600 m².

Condition: excellent (used), Year of construction: 2006, functionality: fully functional, Technical data: - Capacity: 32,000 bph on 1.5L - Formats: 1500 ml - Filling product: Water and Non-carbonated drinks - Blowing/Filling/Capping: COMBI - Closure system: 26.7 mm plastic screw caps Equipment includes: Preform hopper – M. Tanner AG / Prologic Cap hopper – Gassner Preform orientator – M. Tanner AG Blow moulder – Krones Contiform S20 Filler – Krones Volumetric Nitrogen doser – Cryotech International Capper – Krones Bottle inspector – Krones Checkmat Bottle conveyors – Krones SynCo Bledpfjxxbl Njx Abbor Labeller – Krones Etima Coder – Markem SmartLase C350 Shrink-wrapper – Ocme Vega N70/2 Handle applicator – Comag/Decimo HM 100/2 Pack conveyors – Europool Palletiser – Ocme Pegasus M400 Pallet wrapper – Bema Silkworm Turbo Pallet label printer/applicator – Bancale Eidos 7P6ERL

Condition: as good as new (ex-display), Year of construction: 2025, machine/vehicle number: 0816, Compact high-precision CNC rotary indexing table with controller, suitable for single-part or small-batch production in mechanical engineering. Can be mounted in horizontal or vertical orientation. Available for immediate delivery – Made in Germany – This indexer is particularly well-suited as a 4th axis on engraving and milling machines, for milling, engraving, laser marking, drilling, slotting, or for use on tool or surface grinding machines. Suitable for square, hexagonal, and gear cutting of any pitch, as well as 3D machining tasks. Highly precise and accurate—features a worm gear set with a special 100:1 reduction ratio, custom-designed by us and not standard on the market. Output torque: well over 70 Nm. Maximum clamping diameter: 250 mm. Center height: 125 mm. Bljdpfxjbatame Abber Drive is provided via a controlled stepper motor with 200 steps, 7.5 A current, and a holding torque of 9.7 Nm. Achievable output division accuracy: 0.00028125 degrees with 1/64 microstepping. The worm gear set is quadruple ball-bearing mounted and backlash-free, also adjustable. Bearings are from FAG/SKF. The one-piece, robust spindle comes with a 200 mm faceplate, internal taper MK 3, and a through bore of 20.3 mm. Weight: 26 kg. Accessories: - Optional USB data cable for programming - Optional purge air connection - Optional 200 mm three-jaw chuck - Optional guard plate with integrated proximity switch for automatic operation Quick production of flats, complex graduated scales, cross bores, or gearwheels. The electronic controller is a compact module with 14 travel programs and 2 reference runs as well as step monitoring with power supply included in the package. The toolbox module is made of metal. Optimized pre-programming in incremental division angles of 360, 180, 120, 90, 72, 60, 45, 30, 10, 5, 1, 0.02, and 0 degrees. Repeat cycles, clockwise/counterclockwise operation, and cycle pauses are, of course, fully programmable. With the supplied software, you can program travel operations and cycles, as well as absolute or incremental positions. The current value can be conveniently displayed in the software at any time. Via an output, the unit can exclusively receive start impulses from an NC machine. Flats, challenging graduated scales, cross bores, or gearwheels can be produced quickly. Standard clamping devices are available for your applications, and custom fixtures can be manufactured quickly and economically on request. Custom rotary table solutions are also available upon inquiry. Supplied with warranty, German operating manual, and after-sales support since 2006. 1,500 Roundinho rotary tables in use worldwide –

Condition: new, ROGI SAWING MACHINE TYPE CY300N INVERTER Sawing dimensions ----- 2750 x 27 x 0.9 mm Cutting speed ----- 20~80 m/min Bljdsga T Euopfx Abbjr Engine power ----- 1.5 KW ( 400V ) Weight ----- 350 kg Cutting capacity 0 255 mm 200 mm 200 x 320 mm Cutting capacity 45 195 mm 195 mm 195 x 200 mm Cutting capacity 60 125 mm 125 mm 120 x 130 mm Cutting capacity -45 200 mm 170 mm 170 x 200 mm INCLUDED Adjustable material clamp Angle adjustment up to 60 degrees Automatic switch off Low-noise electric motor Closed worm gear transmission Hydraulic pressure control Rotatable undercarriage 45 gr. Emergency stop Cooling pump Support box Quick Release Clamp 1 Saw blade mounted

Condition: used, - Adhesive application with 1 profiled roller for Packaging height 300mm over 1 application roller - The drive via worm gear motor 0.37 kW - 1 ST left - 1 ST right - Fits DIMTER HK 200 and HK 400 spare parts dimter in stock equipment in stock Blsdpfxecht Nyj Abbjr accessories in stock

Condition: used, 1 mortar mixer, manufacturer M-tec, model D 20 II, year 2022, 400V, serial no. 5800220521 Bedpfx Asxvy Taebbjlr

Condition: good (used), Bushing, motor flange/worm connection, sleeve, connecting sleeve Blsdewzr I Aspfx Abbjr -Socket: for motor flange/worm connection -Type: Shaft Ø 60 mm -Quantity: 1x sleeve available -Price: per piece -Dimensions total: Ø 120 x 220 mm -Weight: 13.4 kg/piece

Year of construction: 1971, condition: used, Technical details: max. wheel diameter: 300 mm max. module: 5 module min. : 0,5 max. workpiece weight: 60 kg weight of the machine ca.: 4,0 t dimensions of machine: 1800x1850x2500 mm Bodpevc Apbjfx Abbslr dimensions electric cabinet: Nr. 1: 1930x400x1920 mm dimensions electric cabinet: Nr. 2: 800x230x1950 mm dimensions:: Abluftanlage: 1400x700x560 mm dimension cooling device LxWxH: 1,2 x 1,0 x 0,45 m Electronically controlled tooth flank grinding machine up to module 5 and a Ø of 240 - 300 mm feed speed per workpiece revolution infinitely variable 0.4 - 3.2 mm max./min. Number of teeth: 130 / 12 max./min. Pressure angle: 30° / 14°30` max./min. Spiral pitch with 24 teeth: 6000 / 200 mm max. tooth helix angle, both sides: 45° Speed of the grinding worm: 1900 rpm without dressing device Equipment: approx. 77x change transmission wheels, pipe extensions and various tools Two of these machines are for sale. Both machines are supplied via two common control cabinets and an exhaust air system. *

Condition: good (used), Peter Wolters AC500 lapping machine TECHNICAL DATA AND SCOPE OF SUPPLY TECHNICAL DATA Rolling device size: 42 TS 7/14 Working disk diameter: 415 mm Ring width: 54 mm Working disk thickness: 50 mm Possible wear of the disks to approx.: 20 mm Number of rotor disks: 14 Drive data: 380 V / 50 Hz Upper disk drive: 1.0 / 1.4 kW Worm gear motor: 56 / 112 rpm Lower disk drive: 1.0 / 1.4 kW Worm gear motor: 500 / 100 rpm Workpiece drive: 0.5 / 0.7 / 0.9 kW 3-pole worm gear motor: 6 / 18 / 36 rpm Tilt arm drive: 0.25 kW Digital load adjustment of the upper work disk: 0-250 daN Connection data Electrical connection: 5.0 kW Compressed air connection: 5-7 bar Compressed air consumption: Approx. 8 Nl/min OFFER SCOPE U.A: (list not exhaustive): Peter Wolters AC 500 lapping machine / fine grinding machine 1 inverter per motor documentation Exact scope of offer according to photo gallery Bjdpfx Abjtxitvobjlr No responsibility is taken for the correctness, completeness and up-to-dateness of the information.

Condition: new, ROGI SAWING MACHINE TYPE CY300 INVERTER Sawing dimensions 2750 x 27 x 0.9 mm Sawing speeds variable 20~80 M/min. Engine power 1.5 KW ( 400V ) Weight 390 Kg Sawing capacity 0 degrees Round 255 mm Square 210x310 mm Sawing capacity 60 degrees Round 135 mm Square 135x135 mm Sawing capacity -45 degrees Round 220 mm Square 210x200 mm Sawing capacity +45 degrees Round 215 mm Square 210x200 mm INCLUDED Adjustable material clamp Bjdpfxjga Twuj Abbjlr Grading to 45 degrees Automatic switch off Low noise electric motor Closed worm gear transmission Hydraulic pressure control Rotatable undercarriage 45 gr. Emergency stop Cooling pump Support box Quick Release Clamp 1 Saw blade mounted

Condition: refurbished (used), Refurbished Landert motor Manufacturer: Landert Motoren AG Bülach Type 132S-RFA4A, 1450/1750 rpm, 400V, 50/60 Hz, 5.5 kW (Grinding worm drive) Blsdpfx Abow Rn Hxsber All technical data subject to errors and omissions. Price on request Sale exclusively within EU countries.

Condition: used, 1 mortar mixing machine, manufacturer M-tec, model D 20 II, year 2024, 400V, serial no. 5800240504 Bljdsxvy N Iopfx Abbsr

Condition: good (used), Year of construction: 2022, travel distance X-axis: 850 mm, travel distance Y-axis: 700 mm, travel distance Z-axis: 500 mm, Machine hours ON 10,500 Bledpfxjw Igf Ij Abbor Spindle hours 4,400 Hermle C 400 U, Year of manufacture 2022, Control Heidenhain TNC 640, Travel X/Y/Z 850/700/500 mm, 2-axis NC swivel rotary table Ø 650 mm, Tool changer with 38 positions, Additional magazine with 88 positions - can be extended as required, C axis with worm drive, A axis single-sided drive, Spindle speed up to 18,000 rpm, HSK A 63, Electronic thermal compensation, Electronic handwheel, ICS 40 bar, conveyor belt filtration system, Measuring scales with purge air, Scraper conveyor, Manual cabin door, Manual cabin roof, Blum laser for tool breakage / tool measurement, Heidenhain 3D probe, Oil mist extraction, DNC system, Dynamic Efficiency, Dynamic Precision, OCM - Optimized Contour Milling, 1 set of new polycarbonate viewing panels incl. seals,

Year of construction: 1971, condition: used, Technical details: max. wheel diameter: 300 mm max. module: 5 module min. : 0,5 max. workpiece weight: 60 kg weight of the machine ca.: 4,0 t machine dimensions LxWxH: 1,8 x 1,9 x 2,5 m dimensions electric cabinet LxWxH: Nr. 1: 1,95 x 0,4 x 1,95 m dimensions electric cabinet LxWxH: Nr. 2: 0,8 x 0,23 x 1,95 m dimensions:: Abluftanlage: 1,4 x 0,7 x 0,55 m Electronically controlled tooth flank grinding machine up to module 5 and a Ø of 240 - 300 mm feed speed per workpiece revolution infinitely variable 0.4 - 3.2 mm max./min. Number of teeth: 130 / 12 max./min. Pressure angle: 30° / 14°30` max./min. Spiral pitch with 24 teeth: 6000 / 200 mm max. tooth helix angle, both sides: 45° Speed of the grinding worm: 1900 rpm Bedpjvc An Defx Abbolr without dressing device Equipment: approx. 69x change transmission wheels, pipe extensions and various tools Two of these machines are for sale. Both machines are supplied via two common control cabinets and an exhaust air system. *

Condition: new, Year of construction: 2025, functionality: fully functional, travel distance X-axis: 3,200 mm, travel distance Y-axis: 1,600 mm, travel distance Z-axis: 200 mm, rapid traverse X-axis: 50 m/min, rapid traverse Y-axis: 50 m/min, rapid traverse Z-axis: 15 m/min, controller manufacturer: LNC-Control, workpiece length (max.): 3,200 mm, workpiece width (max.): 2,100 mm, workpiece height (max.): 200 mm, workpiece weight (max.): 1,500 kg, Equipment: rotational speed infinitely variable, BudgeCaft is a manufacturer of high-quality CNC machines. We design, develop, assemble, and sell CNC machines for businesses and industrial manufacturers. BEST DEAL Transport, installation, machine instruction, and CAD/CAM training are provided by Danmar Machines (languages: Dutch, English, French, Italian, or German). Additional charges may apply depending on the location. • Starter tool kit • ISO30 • ER32/ER40 collets • Vacuum pump • ATC spindle CC 9 kW • 1 year of online support/helpdesk for CAD/software (English) • 12-month standard factory warranty Suitable for machining: wood, panel material, acrylic, PVC, aluminum, foam, multiplex board, plasterboard, rock wool, plastics, etc. - 9 kW ATC spindle ISO30 ER32/ER40 - LNC MW control system - Leadshine servo motors - Tool change magazine - Vacuum table - Vacuum pump - Powerful side channel blower, air pump - Pegasus CAD/CAM software Custom configurations available Working area dimensions:  1300 x 2600mm € 31,800  1600 x 3200mm € 37,500  2100 x 3200mm € 41,600 Linear tool magazine automatic changer: 10-12-16 position tool changers, automatic tool change during operation. Working area X-axis: 2600-3200 mm Working area Y-axis: 1300-1600-2100 mm Z-axis stroke: 200 mm Gantry construction: Yes Spindle motor: 9 kW servo motor (ATC spindle) Speed: 1,000-24,000 rpm Axis travel X-axis: 50 m/min Axis travel Y-axis: 50 m/min Axis travel Z-axis: 15 m/min Bedpfx Ajwc Uadsbbelr Tool holder: ISO30-ER32-ER40 Software: Pegasus PWoodEntry Vacuum pump: included

Condition: used, Year of construction: 2006, COMPLETE BOTTLING LINE KRONES 30,000 bph Product: still water Speed: 30,000 bph – 1.5 L PET Preform tipper - 2018 Model: m.tanner ag/prologic Caps elevator Gassner - 2006 Manufacturer: Gassner Preform aligner (part of the blow molding machine) - 2006 Monobloc with blow moulder, filler and capper Blow molding machine - 2006 Brand: Krones Model: Krones Contiform S20 Type: Rotary Number of molds: 20 Filler - 2006 Brand: Krones Model: Krones Volumetic Direction: Counterclockwise Number of filling valves: 84 Type of filling system: gravity flowmeter Capper (part of the monobloc) - 2006 Brand: Krones Number of heads: 18 Type of cap: Alaska 3 Principles Distribution system: pick & place Nitrogen dispenser - 2006 Model: Cryotech International Inspector for level control and cap - 2006 Bjdpfxovwcdze Abbolr Model: Krones Checkmat Bottle transport - 2006 Model: Krones Synco Dryer tunnel - 2006 Brand: Europool Model: TF-04 Labeller - 2006 Brand: Krones Model: Krones Etima Type of labeller: Rotary Direction of rotation: Counterclockwise Type of labeling: Rollfed Number of stations: 1 Number of heads: 18 Type of applicable labels: OPP Plate handling: lobe cam Head adjustment: electric American input and 2 parallel outputs Label presence check on output tape Marker - 2015 Model: Markem Smart Lase C350 Shrink wrapper - 2006 Brand: OCME Model: Vega N70/2 Film launching Dual Input Handle applicator - 2006 Brand: Comag Model: Decimo HM 100/2 Equipped for bundles: 3x2 Dual Input Bundle transport: Brand: Europool Palletizer - 2006 Brand: OCME Model: Pegasus M400 Type: Layered Pallet warehouse Interlayer system Maximum workable height: 225 cm - pallet Workable pallet size: 80 cm x 120 cm Pallet wrapper - 2006 Brand: Bema Model: Silkworm Turbo Maximum workable height: 225 cm - pallet Wrapping type: rotary table Top sheet spreader Pre-stretch Pallet labeller - 2020 Brand: Eidos Model: 7P6ERLP

Condition: like new (used), Year of construction: 1989, machine/vehicle number: 13.152, 3 axis CNC heavy duty roll/turbine lathe WALDRICH SIEGEN, model DH 1600 x 12000, max. work piece dia. 1.600 mm, max. turn lengths 12.000 mm, max. work piece weight 40 t, hydrostatic guide ways in Z and X, C axis in the face plate, hydrostatic worm drive, 2 chip conveyor, machine in as good as new condition Option: new CNC Control SINUMERIK 840 DsL, new Electric, new axis motors, Bodpfx Aod Thn Hebbjlr new wiring and installation and commissioning in customers plant

Condition: used, 1 unit plastering machine, manufacturer PFT, model Ritmo L Bljdpsxvy Idsfx Abbor

Condition: used, Year of construction: 2008, Technical details: table diameter: 1000 mm table height: 75 mm max. table load: 250 kg weight of the machine approx.: 1128 kg dimensions: Aggregat: L: 1400 x B: 1000 x H: 160 mm 1-axis NC rotary table - horizontal Positioning and rotary machining mode; intermittent operation with 8 star-shaped T-slots according to DIN 650: a=18H7; h=31mm; b=31mm; c=13mm x length 380mm Finished surface Overall height 250mm Turning: Rotation 360°, by means of incremental encoder, speed 2160°/min. Angular acceleration 120°/sec.²; positioning time 0.867 sec., speed max. 6 rpm, machining 1 rpm. Load on indexing plate axial max. 100kN, radial max. 115kN; Torques tangential 14,000 Nm as well as worm gear 7,000 Nm and circular machining 2,700 Nm Measuring system Heidenhain - RON 886 C type connections (2x G 1/4" and 2x G 1/8") Bledpfx Abeu N D A Tobjr *

Condition: used, Year of construction: 1993, Technical details: saw blade diameter: 250 mm saw blade drill hole: 30 mm Cutting depth: 68 mm Cutting length: 450 mm Bljdpfsu Nifyjx Abbsr total power requirement: 2,55 kW weight of the machine approx.: 150 kg dimensions L x W x H: 0,85 x 0,86 x 1,4 m This circular saw is hand operated, equipped with a table support 400 x 860 x 22mm, relocatable, which is placed on a frame. Uses: Wood, thermosetting plastics, plaster, chipboard and other similar materials. Details of the swivel arm: Length 800mm, max. projection 580mm, swiveling 45° right/left their indication via radial scale. Sawhorse data: Feed manually (handle), tiltable 90° left their indication via radial scale, motor 380V with 2,700 rpm, protection class IP44, *