Used Parquet Press for sale (27,724)

Condition: used, Year of construction: 2005, functionality: fully functional, Clamping Force: 2450 kN Working pressure: 206 bar Heating plate dimensions: 570 x 610 mm diameter of piston: 400 mm max. stroke: 140 mm daylight: 150 / 180 mm max. mass of heating plant: 250 kg capacity of oil tank: 150 L rated capacity: 55,2 kW heating capacity: 36,6 kW engine output, vacuum motor: 3,6 kW Ibsdpfoxphktjx Aacoc Between light curtain and mould area: 270 mm Stroke of vacuum cover: 140 mm machine dimensions LxWxH: 4000 x 2850 x 2600 mm The vulcanizing press from manufacturer PAN STONE, was used by a renowned German company specializing in sealing technology and electromobility. This company is known for its high quality and innovation in seal production. It was always professionally maintained and repaired, which explains its excellent condition. This press offers you the opportunity to invest in proven technology that was utilized by a leading company in Germany.

Condition: used, Year of construction: 1987, With this roll press, you can press different materials together in a single pass. Application example: Previously, sandwich panels were bonded and pressed with this machine. Technical data: Isdpfx Aewd Nx Djacjbc - Manufacturer: Bürkle - Type: AM - Year of manufacture: 1987 - Working width: 1,600 mm - Working height: 880 + - 20 mm - Part height 20 - 160 mm - Operating side left - Pressure cylinder from above, rubberised - Counterpressure cylinder from below, rubberised - Width of counterpressure cylinder 1,700 mm - Feed 3 m/min. - Total electrical connection - Volt/Hz 400/50 - Location in warehouse in Blomberg

Condition: excellent (used), Year of construction: 2017, operating hours: 3,200 h, pressing force: 130 t, Space requirement: 11,500 mm x 10,000 mm + Increased installation height/lift + 230 mm + 4-axis backgauge system + Rear work area lighting + Front work area lighting - TruBend documentation Automation BendMaster (60) Standard equipment: BendMaster - Sturdy base frame and manipulator made of cast aluminum construction - Load capacity 60 kg, sheet plus gripper - Low-level floor track in welded construction - Sheet sensor for contour detection - Rotary feedthrough for quick gripper change Gripper coupling on the BendMaster - Sensor system for 4-axis backgauge system - Electric drives - Double sheet detection - NC regrip station - Vacuum generation for suction grippers Control - TRUMPF PC control with operator terminal - Teleservice via internet - Convenient operation: screen, mouse, keyboard Safety - Safety fence with access door Special equipment + Track extension to 10 m + Gripper change console + Modular vacuum gripper without separation (materials for 3 grippers) + Modular vacuum gripper with separation (materials for 3 grippers) + Clamp gripper with rotary axis + Sheet removal station with linear axis + Additional pallet for sheet removal station + Right-hand side door for safety fence (or left-hand side in combination with ToolMaster) Machine - Robust machine frame entirely in steel construction - Press beam - Spherical mounting of pressure beam with inclined position - Electro-hydraulic upper drive system with 4-cylinder technology - Optical set-up and positioning assist with control valves - Generous free space for bending - Flat front covers - Block hydraulic system - Electronic pressure gauge Ibedsxayl Depfx Aacec - Measuring system with glass scale and spring-back compensation - Hydraulic oil in machine (lifetime lubrication) - Oil cooler - Electrical cabinet cooling via air-to-air heat exchanger - Modern machine design Backgauge System - 2-axis backgauge system, X and R axes Tool Clamping - Hydraulic upper tool clamping - Lower tool holder, hydraulic clamping, hardened - Lower tool displacement, 2 positions, pneumatic Crowning - CNC crowning Control - TRUMPF TASC 6000 - Graphical workshop programming - Windows XPe (embedded), Pentium 4 with 2.8 GHz clock speed - 2 GB RAM - 15-inch touch screen - Network capability - Teleservice via internet Operation - Control panel with LCD keypad and foot switch - Communication rail - MobilControl Safety - Standard safety equipment - CE marking

Condition: used, Year of construction: 2016, Assembly in 2017, consisting of: unwinding and rewinding unit (unwinder/rewinder), each with SIEMENS control system including touch panel, FANUC R2000ic 210f loading robot, control unit (for print unit setup), 8 color printing units (left tower, central tower, right tower). Weight: 16/35/18 t, BST edge guiding system, AHLBRANDT surface treatment (corona station), extraction unit, 5 web tension units, web break sensor, inspection table, BST eltromat register control, serial no.: WA18911, RITTAL control cabinet, PSI electron beam unit with switching and cooling system, pressure vessel, oxygen analysis, BST eltromat web monitoring system, BST eltromat visual defect detection system, year of manufacture: 2017, platform, staircase, mounted control cabinet (for corona station), serial no.: 513783, power: 8 kW, control center (container design), various MITSUBISHI climate control units, specialized media supply (water, electricity, nitrogen, compressed air), central SIEMENS control system, safety fencing, light barriers, total weight approx. 110 t. Isdpfxjxnafae Aacobc

Condition: ready for operation (used), Year of construction: 2009, Brand: HSM Model: V-Press 1160 plus Year of manufacture: 2009 Pressing force: 532 kN Voltage: 400 V Maximum bale weight: up to 550 kg (depending on material) Bale dimensions: 120 x 110 x 120 cm Machine weight: 2403 kg Machine dimensions: 180 x 157 x 298.5 cm Filling opening dimensions: 19.5 x 65 x 111.5 cm Condition: Very good! Checked for proper operation. FLITS Rental & Sales service: every machine comes with a bundle of binding wire (120 wires). Need more binding wire bundles? Request a free quote. At FLITS Rental & Sales you choose speed, clarity, and reliability. We think along with you, respond promptly, and ensure you quickly have access to the right machine. You are welcome to inspect the machines at our location: Schoterlandseweg 94, 8413NE Oudehorne. Visits are possible by appointment, so we can take the time to properly inform you and show you the right machines. We are happy to assist you! Ibedpfxoxnxnte Aacsc Waste baler Paper baler Cardboard baler Plastic baler Waste compactor Recycling Textile baler Waste Waste processing

Condition: ready for operation (used), - invoersysteem voor plat- en hoekstaal - met toevoerwagen en materiaalklem - Vacon 110 software CNC-besturing Hydraulische schaar voor vlak staal VPS 2200 cap: 220 ton maximale lengte: 15 200 mm breedte/dikte: 500/25 mm hoek: +/- 45° Hydraulische hoekschaar voor staal VHS 2400 cap: 240 ton Ibsdewlkw Dspfx Aacsc maximale lengte: 15 200 mm 200 x 200 mm / 16 mm Hydraulisch ponsen VPO 1000 cap: 100 ton ponsdiameter/dikte: 57/15 mm of 32/25 mm 4 ponsunits voor vlak staal (Verticale positie) 1 ponseenheid voor hoekstaal (horizontale positie) incl. gereedschap Hydraulische teller VNI 1/36 1 codeerschijf 36 tekens tekenhoogte x diepte: 10 x 1 mm Hydraulisch aggregaat VHA 37 37 kW - 250 bar

Condition: used, Single-column hydraulic press SCHULZ Type SES 250 . 04.86.3511/3 Year of manufacture: 1986 Pressing force: 25 tons Return force: 10 tons Throat depth: 360 mm Table size: 600 x 720 mm Ram area: 500 x 500 mm Clear hole in table: Ø 100 mm Clamping pin bore: Ø 40 mm Ram stroke: 400 mm Maximum installation height: 600 mm Table height above floor: 935 / 775 mm Hydraulic tank capacity: 380 liters Drive power: 7.5 kW Power connection: 380 Volt, 50 Hz Ibodjhl Npqjpfx Aacoc - Adjustable fixed stop in the press cylinder 180 mm, with hand crank adjustment - SICK light barrier - Two-hand operation - Base made of 160 mm U-steel Space requirement (L x W x H): 1900 x 1300 x 3100 / 3260 mm Weight: 3.6 tons Good condition

Condition: used, Year of construction: 1964, pressure 10 t throat 235 mm stroke ca. 400 mm stroke speed - idle stroke downwards 4,5 m/min stroke speed - idle stroke upwards 10 m/min dayligth ca. 500/600 mm table-size ca. 450 x 400 mm ram hole 32 mm total power requirement 2,2 kW weight of the machine ca. 1,5 t Ibsdpfx Aevgnqfoacjc dimensions of the machine ca. 0,95 x 0,45 x 2,1 m Hydraulic single-column press - from a training workshop, no guarantee on UVV, with two-hand control via separate control panel. Work only with safe tools or solid shields! Machine only works in full stroke, the stroke limiter of the ram cannot be regulated because the adjustment chain needs to be repaired, so it is sold at a special price. Machine dealer with own stock of 1600 m².

Condition: ready for operation (used), functionality: fully functional, machine/vehicle number: 1769, control type: manual, degree of automation: manual, actuation type: hydraulic, bending force (max.): 25 t, working width: 2,000 mm, stroke length: 60 mm, Machine weight 2400 kg Ibjdpfx Aasxpf Txjcjc

Condition: used, Year of construction: 1989, DCM HAC 1400/5 Flexographic 5 Colour Printing Press (1989) With Inkmaster Ink Dispensing system Comprising of: ENR web feed (1994) DCM web cutting (1994) Ijdpfx Asxn N U Rsacebc AFS Corona AVE-150D surface treatment system (2021) Inkmaker PICCS15-21-007 ink dispensing system

Condition: ready for operation (used), Year of construction: 2009, Brand: HSM Model: V-press 860 plus Year of manufacture: 2009 Pressing force: 418 kN Ibedpfsxnxmvox Aacsc Voltage: 400 V Max. bale weight: 430 kg (depending on material) Bale dimensions: 120 x 110 x 85 cm Machine weight: 2083 kg Machine dimensions: 180 cm x 125 cm x 298.5 cm Fill opening dimensions: 120 cm x 65 cm x 85 cm Condition: Very good! Checked for proper operation. FLITS Rental & Sales service: with every machine we supply a bundle of binding wire (120 wires).

Condition: used, Year of construction: 1988, pressure 180 t chamfer lenght 3100 mm distance between columns 2550 mm control Konventionell throat 270 mm back stop - adjustable 550 mm work height max. 900 mm total power requirement 15,0 kW Ibsdpfoxcg E Asx Aacsc weight of the machine ca. 8,2 t dimensions 3,2 x 1,3 x 2,47 m - 1 upper tool, - 1 lower tool, pointed - Motorized backgauge - 2 support arms - Additional upper tool, split, deer foot - Additional lower tool 2170mm

Condition: used, Hydr. differential stroke press, toggle lever hydraulic press, automatic punching press BRUDERER - LEINHAAS type AR 11-100.H Fine blanking press, knuckle-joint press Machine. No. P247 Year of construction 1991 Pressing force 100 ton (1000 kN) Installation height max. 380 mm Table surface 1100 x 700 mm Outlet hole 800 x 220 mm ram surface 690 x 315 mm Frame width 1150 mm Lateral upright width 410 mm Stroke rate 45 and 80 strokes/min. Clamping pin bore Ø 50 mm Compressed air requirement 8-10 bar Hydraulic tank capacity approx. 700 liters Motor power main drive 22 kW Mains connection 400 Volt, 50 Hz, 28 kW - 2 speed settings for the number of strokes (45 and 80 strokes/min.) - electronic cam controller BALLUFF, type Minicontroller BMC4K - electronic tool monitoring EBERLE, type PLS 509S - KISTLER press force monitoring system - table surface with 22 mm T-slots and ram surface with 14 mm T-slots - Electronic stroke counter - motorized height adjustment for the ram - central oil lubrication - Work area shielding through pneumatic opening protective screen - adjacent control cabinet and electrical cabinet - 2 oil coolers with FLUTEC cooling fan (oil-air cooling) - Electrical circuit diagram and printout of PLC program available - Two-hand operation on the machine Ijdpfxjgp T Eue Aacjbc Space requirement (control cabinet) L x W x H 700 x 700 x 2100 mm ( approx. Space requirement (electrical cabinet) L x W x H 1700 x 650 x 2100 mm Space requirement (press) L x W x H 2350 x 1700 x 3300 mm Weight of the press 8500 kg Very good condition

Condition: used, pressure 6 t dayligth 180 mm spindle diameter 32 mm throat 115 mm Isdpfx Asvgnnwsacjbc ram stroke 90 mm table surface area 300x270 mm weight of the machine ca. 70 kg dimensions of the machine ca. 800 x 1350 mm 6 t (estimaeted) hand-operated spindle press. The machine is professionally and durably lashed. Machine dealer with own stock of 1600 m².

Condition: good (used), Year of construction: 2005, 1 used hydraulic press brake Make: Knuth Model: AHK 31160 Year of manufacture: 2005 Technical data Working length: 3000 mm Press capacity: 160 t Stroke: 175 mm Equipped with: Iodpfx Aaoxnp A Uocsbc Elgo control Foot pedal Tooling

Year of construction: 2025, condition: new, New machine Year of manufacture: 2025 Features and technical specifications: Iodpow Nafkefx Aacobc Fully equipped in standard version with: - Robust, torsion-free steel frame, welded and bolted construction - Lamella pressure beam TOP with 6 elements, lamella pressure beam SIDE with 5 elements - Lamella pressure beams with proven tolerance compensation system (Ganner system) for tightly compressed carcass joints - Counter-pressure surfaces (side pressure wall, base) are 38 mm thick, coated, continuous support plates - Continuous pressing surface, height 95 mm, on lower vertical pressure beam - Electromechanical adjustment of both pressure beams via precision trapezoidal thread spindles (with increased lead and concentricity accuracy) and high-performance ball nuts with grease reservoir - The pressing process is carried out electromotorically, via 2 independent worm gear motors (2 x 0.75 kW) - Pressing force of the pressure beams is infinitely variable and electronically controlled by 2 potentiometers, regulated via frequency inverter, ensuring absolutely wear-free force control - Pressing force for horizontal pressure beam: min. 500 daN (kg), infinitely adjustable up to max. 2200 daN (kg) - Pressing force for vertical pressure beam: min. 300 daN (kg), infinitely adjustable up to max. 2200 daN (kg) - Pressing and adjustment speed of the beams with fine positioning, using 3-stage selector switch: 5 / 10 / 25 mm/second - Jog mode for precise positioning of both pressure beams, e.g. for low pressing forces, drawers, and carcasses at 45° - Simplest operation via 6 separate push buttons, 8 movement cycles selectable via control panel - Freely adjustable press time preselection 0-30 min (switchable to seconds or hours), with individually programmable opening dimensions for both pressure beams - Re-pressing function to increase or decrease the pressing force during the pressing process - Working height/loading height: 300 mm - Working dimensions: Length min: 150 mm, max: 2500 mm; Height min: 150 mm, max: 1400 mm; Depth: 700 mm Including surcharge for rapid traverse speed, for fast positioning of the pressure beams, controlled via automatic workpiece detection with sensors in the pressure beams, pressing speeds 5 / 10 / 25 mm/sec and rapid traverse speed 50 mm/sec, the sensors can be deactivated for pressing special components Including a set of machine feet for 500 mm working height Location: Flörsheim Availability: Short-term

Condition: good (used), functionality: fully functional, machine/vehicle number: 151/6, Hydraulic Straightening Press Manufacturer: WALTER Type: WP Machine No.: 151/6 The press has a table size of Length Width Thickness Iedpjxl Tmfofx Aacebc 1000 390 60 mm Cylinder stroke: 400 mm The current distance between cylinder and table is 450 mm. When the table adjustment is set to the lowest notch, the gap between table and cylinder is 850 mm. (See the attached sketch for details) The machine is also equipped with an appropriate control system. Max. Pressing force: 60 tons 180 bar Table height adjustment approx.: 1000 mm (installation dimension) Motor power: 4 kW Two-hand control Emergency stop Foot pedal Stroke limitation via limit switch

Condition: like new (used), Year of construction: 2008, machine/vehicle number: CA7-360 NG, Rotary press-on capper 7 station Ibjdpfxjr Iyi To Aacsc incl hopper/sorter Left-right Central greasing Vögel Pneumatic Festo Siemens S7 controlled min 5.500-max 17.000 cap/hr electric height adjustment tooling capping heads: Diam 65mm/27,4mm Hight Diam 75mm/32mm Hight Diam 94,5mm/40,3mm Hight container size tooling for glass bottle: Diam 65.5mm/104mm hight Diam 75,5mm/140,7mm hight Diam 93,3mm/180mm hight electric 6Kw 400v Pressured air minimum 5bar Machine is in excelent condition.

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2017, operating hours: 4,331 h, machine/vehicle number: 24463, bending force (max.): 200 t, working width: 3,100 mm, stroke length: 350 mm, throat depth: 450 mm, back gauge: 800 mm, TECHNICAL DETAILS Iedpfx Aaoxgdnpjcsbc Bending force: 200 t Distance between columns: 2,550 mm Throat depth: 450 mm Backgauge: 800 mm Max. working width: 3,100 mm Max. stroke: 350 mm MACHINE DETAILS Control: Delem DA-69T (controlled axes: Y1, Y2, X, R, Z1, Z2 + crowning) Dimensions & Weight Dimensions (L x W x H): 4,200 x 2,300 x 2,970 mm Weight: 10,000 kg Motor power: 18.5 kW Operating hours: 4,331 h EQUIPMENT Quick-release system Extra fingers Including tools Documentation CE marking

Year of construction: 1999, condition: ready for operation (used), General Data Machine weight 17000 kg Main Drive Number of axis 2 Max Material Thickness Steel 6 mm Ibodsxf N Skopfx Aacjc Stainless steel 3 mm Aluminium 6 mm This Nisshinbo HIQ-1250 was manufactured in 1999. It is a turret punch press with a working range of 2500 x 1250 mm, handling sheet thickness up to 6 mm for steel and aluminium, and 3 mm for stainless steel. It features a pressing capacity of 22 tons and a ram stroke of 50 mm. If you are looking to get high quality punching capabilities consider the Nisshinbo HIQ-1250 machine we have for sale. Contact us for more information. Application Types Punching

Condition: excellent (used), Year of construction: 2009, Bargain press, year 2009, 7.5 HP. 70 kg/h chip container with discharge and blower fan Ibjdexpkadjpfx Aacec

Year of construction: 1994, condition: good (used), machine/vehicle number: 24.105, A used, well-preserved hydraulic press brake HATASTAR equipped with: - CYBELEC DNC 70 control - Controlled axes Y1;Y2;X;R - Hydraulic upper tool clamping - Hydraulic crowning - FIESSLER AKAS safety system - Tools Iodpfx Aaefthzkscobc - Press book - Documentation bending length 4600mm Stands width 4100mm Press force 1350kN stroke 220mm Rapid traverse 140mm/sec working speed 10mm/sec Retraction speed 100mm/sec Further tech. data see pdf.- document Tech. Data and dimensions: Errors excepted.

Year of construction: 2019, condition: new, We offer press brake tooling and stamping tools machines for TRUMPF, AMADA, BYSTRONIC, LVD, SALVAGNINI, DURMA, ERMAKSAN, MVD, HACO. Standard and special tools Isdpfxod H T Tfe Aacobc Send us your wishes and we offer matching tool.

Year of construction: 1966, condition: good (used), A used eccentric press Weingarten in good condition with pneumatic engagement, piece counter, documentation, press test book, spare parts 2 pallets pressure 1500 kN (150 tons) stroke 60 mm ram small / large stroke 10 - 140 mm Ijdpsir I Slofx Aacobc throat 550 mm Cylindrical holder 30 mm Table W x D 1200 x 1000 mm dimensions W x D x H 150 x 270 x 290 cm Weight 13.500 kg Tech. Data and dimensions: Errors excepted.

Year of construction: 2005, condition: excellent (used), pneumatic punching machine Iedpfx Aasff Apwscjbc