Used Metal Stamping Press for sale (55,367)

Condition: used, Single-column eccentric press WEINGARTEN type ARP 100 Machine no. No. 122481 Year of construction 1984 Pressure capacity 100 ton. throat 400 mm Table size 920 x 660 mm ram surface 700 x 450 mm Rear upright width 735 mm Stroke adjustment 20 - 160 mm Plunger adjustment 80 mm Installation height with 160 mm stroke max. 355 mm (without intermediate table top) Installation height with 20 mm stroke max. 425 mm (without intermediate table plate) Stroke rate 60 strokes/min. Table surface intermediate table top 920 x 610 mm Thickness of intermediate table top 90 mm Hole in intermediate table top Ø 210 / 180 mm Through-hole in machine table Ø 210 / 180 mm Table height above floor 800 mm (without intermediate table top) T-slot width in table and ram 22 mm Clamping pin bore 50 mm Motor power 11 kW Mains connection 400 Volt, 50 Hz - Hydraulic overload protection in ram - ORTLINGHAUS pneumatic clutch/brake combination - Electromotive ram adjustment with counter - Clamping pin bore with clamping piece - Front crankshaft support bearing - Gear reduction gears in closed oil bath gearbox Chsdpfx Adsu Rwa Ijxsd - Two pneumatic tappet compensation cylinders - WOERNER automatic central grease lubrication - Lift release via electric foot switch or two-hand control panel - Electrical control cabinet permanently attached to the machine - Operating instructions and circuit diagram - UVV for manual insertion work Space requirement L x W x H 2200 x 1600 x 3250 mm Weight 8.3 tons Good condition

Condition: excellent (used), Specifications Manufacturer: MANZONI Model: 630 2 MR Year: 1996 Condition: Used Stock number: 0368 Press force: 630 t Number of pressure points: 2 Slide stroke: 250 mm Slide adjustment: 250 mm Strokes per minute: 18-54 Die opening at BDC: 700 mm Bolster size: 2,600 x 1,500 mm Ram size: 2,500 x 1,500 mm Clear front opening between uprights: 2,730 mm Clear opening between trays: 2,500 mm Clear side opening between uprights: 1,000 mm Press weight: 83,000 kg Codpfxew Sat Te Adxohd

Condition: refurbished (used), Year of construction: 1992, machine/vehicle number: 131 644, Attention: machine has been 2022 completely mechanically and electrically retrofitted before delivery press force: 1000kN stroke: 30 - 100mm slide adjustment: 80mm speed: 50 - 300/min shut height. 350mm table dimensions: 1080 x 800mm slide dimensions: 900 x 620mm new electrical controller SIEMENS S7 1500 Chsdpfx Adsfn Affsxod

Year of construction: 1994, condition: good (used), machine/vehicle number: 25286, Built in 1994 Equipment: embossing press: Cjdpfx Adod R Saqjxjhd • case magazine with case bending device DBA (without feeding conveyor) • foil feeder with two pairs of foil feeding rollers • electric counter • delivery conveyor to the right

Year of construction: 2002, condition: ready for operation (used), Main Drive Codpexaql Uofx Adxohd Spindle motor power 11 kW Stroke 110 mm This SEYI SN1-110 was manufactured in 2002. It is a mechanical C-frame crank press with a 110 tons capacity and a stroke of 110 mm. The machine offers an adjustable speed range of 35–65 SPM, a maximum die height of 350 mm, and a main motor of approximately 11 kW (15 HP). Contact us for more information about this machine. Application Types Stamping

Condition: ready for operation (used), With hydraulic pump. Codpfx Adjhw E D Sjxshd

Condition: used, Single-column eccentric press WEINGARTEN type E 40 Machine. No. 643/62 Year of construction 1963 Pressure capacity 40 ton. throat depth 250 mm Table opening 150 x 80 and Ø 200 mm Table surface 560 x 460 mm ram surface 250 x 200 mm Codpfotx E Rqex Adxohd Plunger stroke adjustable 8-88 mm Plunger adjustment 63 mm Installation height 320 mm Clamping pin bore Ø 40 mm Stroke rate 100/130 strokes / min. Motor power 2.2 / 3 kW Mains connection 400 Volt, 50 Hz Table height above floor 840 mm - Clutch/brake combination with WEINGARTEN friction threaded clutch with TDC run-through protection - Electric lift release via two-hand control - Overload protection by breaker plate - Manual central grease lubrication - Front crankshaft support bearing - Control cabinet adjacent - UVV for manual insertion work Space requirement L x W x H 1800 x 1500 x 2200 mm Weight 3.1 tons

Condition: excellent (used), Manufacturer: ROVETTA Model: S4-600 Codow Hck Eepfx Adxehd Year: 2002 Condition: Used Stock number: 0363-0364-0365-0366 Pressing force: 800 tons Number of connecting rods: 4 Drive mechanism: LINK DRIVE Ram stroke: 900 mm Ram adjustment: 500 mm Ram dimensions: 4,500 x 2,300 mm Table dimensions: 4,500 x 2,300 mm Lateral opening in frame: 2,450 mm Usable front passage: 4,500 mm Die space at BDC: max. 1,500 mm, min. 1,000 mm Hydraulic safety device: Present Side removable carriage: Present

Condition: good (used), Year of construction: 1976, Pressing force: 20 t Stroke rate: max. 150 rpm, adjustable via PIV gearbox from the control panel Stroke, adjustable: 10 - 50 mm Installation height: 270 mm (maximum stroke at top, without wedge plate) Ram reinforcement: 50 mm Table area: 340 x 320 mm (W x D) Pass-through opening: 70 x 180 mm (W x D) Ram area: 160 x 230 mm (W x D) with wedge plate Drive power: 2 HP Features: - 1 connecting rod - Double V-ram guide - Motorized oil lubrication - Manual ram adjustment, 50 mm - Mounting bracket for feed unit, tiltable - 3 cams for feed unit etc. - Free-standing control panel - Forward and reverse operation Chjdpowufrzofx Adxsd - Manual setup using a rod

Condition: new, Year of construction: 2025, Bending machine PROD-MASZ to the plate ZGR 2640/1.2 is a sensational machine for precision bending of all types of metal sheets (steel 1.2mm, titanium zinc 1.2mm, aluminum of 1.5 mm, copper sheet 0.8 mm). Equipped with a rack supporting plate, two front bumpers, bending angle measurement, a single lock of bending angle, turnbuckles, eccentric mechanisms. Each part of the machine is adjustable, which allows for adjustment of the arc bending. Used in the device locking system (set by the operator) allows you to achieve the desired angle of bending. Table rear and front bumpers are made of galvanized racks. Ideal for all kinds of steel treatments - wherever the roof is exposed to moisture infiltration. Proper execution of these connections certainly prolong the life of the roof. Chedjdad Adepfx Adxed By hers construction she can be used not only for bending panels with both the ferrous metal, sheets of plastic and fiberboard. - Max. bending angle: 145 degrees - Rotary shears cut to full working length - Thickness of bending bar: 24 mm - Protractor - Weight: 350 kg Rotary shears (max. plate gauge 0,8 mm / Steel) + 350 Euro - The machine have certificate CE and 12 months warranty. Only shipping is possible Delivery every week Price excl. shipping We provide invoices with 0% of tax.

Year of construction: 2007, condition: ready for operation (used), General Data Machine weight 1000–2000 kg Main Drive Number of axis 2 Csdpfx Adsxaqmfjxjhd This BRUDERER BSTA 25 was manufactured in 2007. A high-speed precision stamping press, it features a vertical main ram for precise stamping and a horizontal feed mechanism for workpiece positioning. Ideal for sheet metal forming, stamping, pressing, and metal shaping, it operates at high speeds with computerized control. Compact design ensures space-saving installation. Consider the opportunity to buy this BRUDERER BSTA 25 metal press. Contact us for more information. Application Types Forming

Condition: used, Antike Kniehebelprägepresse / Antique Embossing Hot Stamping Press Karl Krause KHP Baujahr / Year ca. 1930 - Serial-No. 48090 Prägefläche / Embossing Size max. 340 x 430mm Beheizung mit Gas / Heating with Gas Chjdpfowtw E Dex Adxed Online-Video-Inspection by WhatsApp - MS Zoom - Telegram On Stock Emskirchen/Nürnberg - Available Immediately - Can be test

Condition: used, Revolving briquetting press RUF type RBK 55/2500/120 S Hydraulic pellet press or briquetting press for grinding sludge, metal chips, or similar No. 70002 Year of construction 2009 Briquette diameter 120 mm Briquette length in the pre-compactor approx. 120 mm Pressing force in the pre-compactor 30 tons at 260 bar Briquette length in the main compactor approx. 80 mm Pressing force of the main press cylinder 250 tons at 260 bar Stroke size of the main press cylinder 120 mm Pressing force of the counter-press cylinder 250 tons at 260 bar Stroke size of the counterpress cylinder 15 mm Piston diameter of the main press cylinder 350 mm Press stroke Cycle time approx. 30 sec. for grinding sludge with low residual oil content Hopper size of the screw conveyor 1000 x 600 mm Chodpfxjhg Uz Is Adxjd Hydraulic motor power 37 kW Mains connection 400 Volt, 50 Hz, 45 kW - Revolver with 5 stations for high material throughput - Pre-compressor stage for pressing material into the turret disk - 2 opposing main press cylinders with 120 mm and 15 mm stroke - Ejection cylinder for ejecting the finished briquettes from the turret disk - Infinitely variable adjustment of the hydraulic speed for each pressing stage - was used for grinding sludge from metal processing - Material hopper as hopper with screw conveyor - the machine was completely overhauled at RUF in 2018 - a new SIEMENS Simatic touch panel was installed in 2020 - only a few operating hours after the overhaul very good condition Grinding sludge recycling - great savings through cooling lubricant recovery - Large savings in disposal costs due to the reduction in volume and weight of the grinding sludge - Grinding sludge briquettes with a low residual oil content can possibly be classified as "non-hazardous waste".

Condition: reconditioned (used), Year of construction: 1983, Power: 2.000 kN Frequency: 60 rpm Stroke, adjustable: 20 - 120 mm Daylight: 450mm (max. stroke up) Ram adjustement: 100mm Size of bolster: 850 x 810mm Opening in bolster: 00 x 50mm Ram area: 750 x 810mm Motor power: 22 kW Chedpfx Adsgpxc Sexsd equipped by: - 1pc. con rod - 6pc. guideways - hydraulic overload - motorized oil lubrication - motorized ram adjustment - manuel stroke adjustment - pneumatic ram balancing cylinder - anti vibration machine feet

Condition: used, Prägepresse / Hot Foil Stamping Press Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test Codpfx Adet Drnxjxohd

Condition: used, Hand - swing bending machine KRAMER type AMS 650 x 1,5 Chodpfx Asdzqaajdxjd Hand swivel bending machine, press brake year of construction approx. 1985 working length 650 mm sheet thickness at 40 kg/mm2 1,5 mm upper beam opening approx. 60 mm bending beam adjustment ca- 0-25 mm bending angle 0-180 - Upper beam adjustment via hand crank - pre-screw rail for the bending beam - one-piece sharpening rail 135° space requirement L x W x H 1200 x 600 x 1100 mm weight 160 kg good condition

Condition: good (used), Year of construction: 1986, operating hours: 10,000 h, power: 30 to (US) , app. 270kN bolster area: 30" x 21" = 762 x 533mm ram-area: 800 x 300mm Csdpfsnl Snex Adxohd strokes/min: 100...1400 1/min stroke (fixed): 1" = 25,4mm ram adjustement: 1,75" = 44,5mm Equiped by * Hydraulic clutch * Roll feeder Make: Sankyo Type: Variax V70 Width: max. 100mm Only app. 10.000 working hours

Condition: used, machine/vehicle number: 24118, Kniehebelprägepresse - Embossing Stamping Press Krause KHP Prägefläche / Stamping size: 350 x 400 mm Sehr guter Zustand / Beautiful condition Online-Video-Inspection by Skype-Video Chodpfeut Tkgox Adxed We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

Condition: used, Single-column eccentric press EBU Type 75 SKU Machine no. No. P 4598462 Year of construction 1962 Compressive force 75 ton. throat depth 300 mm Table surface 800 x 620 mm waste hole 325 x 225 mm Plunger surface 470 x 180 mm Clamping pin bore Ø 40 mm Table height above floor 845 mm Stroke adjustment 16 - 140 mm Plunger adjustment 80 mm Installation height max. approx. 420 mm Stroke rate 60 + 105 strokes/min. Motor power 4 kW Mains connection 380 Volt, 50 Hz. - Pneumatic clutch/brake combination EBU - Overload protection with breaker plate in ram - UNIDOR tool monitoring system, type APS MINI - mechanically driven gripper feed with belt straightener OSTERKAMP, type ZPN 200/350 - strip width: 200 mm, feed length: max. 350 mm - Strip thickness: max. 3 mm or approx. 200 x 1.5 mm - 2 speeds due to 2 V-belt stages on the wheel transmission - Two-handed operation - Simple work area shielding for swinging open - Table height adjustment in lowest position = threaded spindles for adjustment 50 mm below floor level - Control cabinet and control panel for tool monitoring adjacent Chodpfjdzqltsx Adxsd - Automatic central lubrication - 4 machine feet Space requirement L x W x H 2600 x 2300 x 2450 mm Weight approx. 5.5 tons good condition

Condition: good (used), Year of construction: 1984, Power: 800 kN Frequency: 30 - 200 rpm, adjustable by PIV gearing Stroke, adjustable: 20 - 100 mm Daylight: 500mm (max. stroke up) Ram adjustement: 75mm Size of bolster: 1.010 x 800mm Opening in bolster: 700 x 150mm Ram area: 860 x 700mm Motor power: 22 kW equipped by: - 8pc. guideways - hydraulic overload - motorized oil lubrication - motorized ram adjustment - electro pneumatic stroke adjustment with complete decoiling line make ALBA, consisting of: Decoiler Outer diameter max. 1.400mm Csdpfx Adsdhzf Iexshd equipped by: • Decoiler moveable hydraulic • hydraulic coil loading device • hydraulic drive • hydraulic expansion 480 - 530mm • hydraulic pressure arm, lateral adjustable by handwheel • lateral arms Straightener Type: Ma Ria 9 Width: max. 400mm Thickness: 0,5 - 5,0mm Number of pulling rolls: 2 pc., Ø 120mm, upper can be lifted by hydraulic Number of straightening rolls: 9 pc., Ø 60mm, upper rollls adjustable by hydraulic drive, all rolls supported equipped by: • hydraulic strip insertion device • lateral strip guidings at entrance • lateral strip guidings at exit • basket at exit • loop control by sensor • lateral loop guiding Roll feeder Type: Vhy 400 Width: max. 400mm Thickness: max. 5,0mm passline adjustement by hydraulic jack We can offer even only press or decoiling line

Condition: used, machine/vehicle number: 21035, Heißpräge - Kniehebelprägepresse - Embossing Hot Stamping Press Krause FNPSerial-No. 4798 Stamping size: 550 x 400 mm Chodpfxoh Ayg Uj Adxed Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

Condition: used, Single-column Eccentric Press MÜLLER GEFREES Type 60 SV DK (Identical to ExP60) Very lightly used eccentric press in original condition Machine No. 5250686 Year of manufacture: 1986 Nearly new condition Press force: 60 tons Throat depth: 280 mm Table surface: 740 x 560 mm Ram surface: 385 x 200 mm Through-hole in table: 300 x 200 mm Table surface (intermediate plate): 740 x 560 mm Through-hole in intermediate plate: Ø 103 mm Intermediate plate thickness: 70 mm Clamping pin bore: 40 mm Table height above floor: 815 mm (with intermediate plate) Installation height, max.: 275 mm (with intermediate plate) Installation height, max.: 345 mm (without intermediate plate) Stroke adjustment: 10–90 mm Ram adjustment: 60 mm Strokes per minute: 100 Motor power: 3 kW Drive: 380 Volt, 50 Hz - Mechanical rotary wedge clutch with pneumatic actuation - Spring-loaded single-jaw brake, controlled by cam disc - Stroke release via pneumatic footswitch - Overload protection with breaking plate in the ram - Table height adjustment via 2 threaded spindles - Manual central lubrication system by BEKA Schmiertechnik - Operating manual and pneumatic diagram included Space requirement (L x W x H): 1400 x 1100 x 2200 mm Weight: 3.4 tons In very good, almost new condition Cjdpfoi A A Tbjx Adxjhd

Condition: used, machine/vehicle number: 18040, Kniehebelprägepresse - Embossing hot stamping press Hans Schilling HSMSerial-No. 18040 Chodpfsh Axf Hex Adxjd Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

Condition: used, CNC press brake FASTI type 904-125/30 serial no. 95-904-5775 year of construction 1995 Pressure capacity 125 ton. Working length 3050 mm Stroke approx. 335 mm Stand projection 300 mm Clearance between the side uprights 2550 mm Tool installation height max. 465 mm (opening width between the tool holders) Table width 90 mm (the clamping system is mounted on the table) Table height above floor 875 mm (910 mm with clamping system) Backgauge X-axis 500 mm Backgauge R-axis 115 mm Backgauge Z-axis approx. 1950 mm Lowering speed Y rapid traverse 90 mm/s Chsdohmmfkepfx Adxed Lowering speed Y-operation 8.9 mm/s Return stroke speed Y-retraction 75 mm/s Oil filling approx. 160 liters Motor power 18.5 kW Mains connection 400 Volt, 50 Hz, 20 Amp. - 7-axis CNC control DELEM type DA 58 with LCD screen - 1 axis for back gauge - stop depth (X-axis) - 2 axes for back gauge - fence height (finger R1 + finger R2) - 2 axes for back gauge - stop finger, laterally movable (finger Z1 + finger Z2) - 2 axes for press beam with servo valves and measuring system Y1 and Y2 - Operation via electric foot switch and 2-hand control panel or 2-hand control panel only - Hydraulic tool clamping for the TRUMPF upper tool system, with 20 mm clamping groove - Hydraulic tool clamping for the lower tool with 13 mm table groove, depth 21 mm (tool pin 13 x 20 mm) - FIESSLER safety light barrier, type AKAS - 2 material support arms at the front, manually movable to the side and height-adjustable - Electrical diagram, hydraulic diagram, user manual for control available - Control cabinet on the machine - without tools Space requirement L x W x H 5000 x 2500 x 3050 mm Transport dimensions L x W x H 5200 x 1900 x 2950 mm Weight 8.5 tons. Good condition

Condition: used, Kniehebelprägepresse - Embossing Stamping Press Krause KHP Prägefläche / Stamping size: 350 x 400 mm Sehr guter Zustand / Beautiful condition Chsdpevi Hh Iofx Adxod Online-Video-Inspection...