Used Electrostatic for sale (104)

Condition: new, Year of construction: 2025, Curing ovens shown in the photos can vary in price depending on size, configuration, and optional features. 💡📏⚙️ At ROMER, we manufacture both standard models and fully bespoke solutions, tailored to your process requirements. 🏭✅ Tell us your part size, line capacity, curing profile, and available space - and we will propose the best setup and the options that actually improve daily performance. 🔥🎯 🧠📡 Control and monitoring Live process control for temperature, time, airflow, and modes - with alarms and saved recipes for repeatable cycles. 🔁✅ 🔥🧩 Heating module Fast heat-up and stable temperature thanks to efficient heating elements and quick energy transfer. ⚡🌡️ 🌀💨 Air circulation Uniform airflow reduces temperature differences for consistent coating quality. 🎯✅ 🧱❄️ Insulation and design Smart chamber construction minimizes heat loss - faster reaching setpoint, lower consumption. ♻️📉 🛡️⚠️ Safety and certification Sensors, interlocks, and protection logic increase safety and reliability. 🔒👷 ⚡💰 High efficiency Optimized heat transfer and reduced losses mean real operating savings. 📉🔥 ⏰🤖 Automatic start Programmable schedule - automatic preheating before the shift for smoother production starts. ⏱️✅ 🚪🔒 Self-latching doors + intelligent chimney Prevents accidental opening, chimney activates only when needed for safer operation. 🧯✅ Ibedpfx Afszduplsuoc 🌿🔋 ECO mode Low-energy standby when idle - fuel consumption reduction up to 20% (depending on process). 🌱📉 👀💡 View and lighting Inspection without opening the door - fewer temperature drops, easier supervision. ✨👁️ 🛤️🔥 Guide rails + automatic hood Heat hood runs only during loading to reduce temperature loss, automatic rail infeed improves ergonomics and loading speed. 🙌⚙️ 🎛️🌡️ MULTI-ZONE HEAT Independent zone control for uniform curing of parts with different mass and geometry. 🧩✅ 🧠♨️ MTS system Heating elements mounted without thermal bridges - higher efficiency and faster time to set temperature. ⚡⏱️ 2-in-1 🧱↔️🧱 Split chamber Movable partition for two independent zones - drying and curing in one unit for maximum flexibility. 🚀🔁 🎚️🌀 VFD ventilation Variable fan speed based on chamber conditions - better control and lower electricity use. ⚙️💡

Condition: new, Year of construction: 2025, Curing ovens shown in the photos can vary in price depending on size, configuration, and optional features. 💡📏⚙️ At ROMER, we manufacture both standard models and fully bespoke solutions, tailored to your process requirements. 🏭✅ Tell us your part size, line capacity, curing profile, and available space - and we will propose the best setup and the options that actually improve daily performance. 🔥🎯 🧠📡 Control and monitoring Live process control for temperature, time, airflow, and modes - with alarms and saved recipes for repeatable cycles. 🔁✅ 🔥🧩 Heating module Fast heat-up and stable temperature thanks to efficient heating elements and quick energy transfer. ⚡🌡️ 🌀💨 Air circulation Uniform airflow reduces temperature differences for consistent coating quality. 🎯✅ 🧱❄️ Insulation and design Smart chamber construction minimizes heat loss - faster reaching setpoint, lower consumption. ♻️📉 🛡️⚠️ Safety and certification Sensors, interlocks, and protection logic increase safety and reliability. 🔒👷 ⚡💰 High efficiency Optimized heat transfer and reduced losses mean real operating savings. 📉🔥 ⏰🤖 Automatic start Programmable schedule - automatic preheating before the shift for smoother production starts. ⏱️✅ 🚪🔒 Self-latching doors + intelligent chimney Iedpoyg H Ersfx Afusbc Prevents accidental opening, chimney activates only when needed for safer operation. 🧯✅ 🌿🔋 ECO mode Low-energy standby when idle - fuel consumption reduction up to 20% (depending on process). 🌱📉 👀💡 View and lighting Inspection without opening the door - fewer temperature drops, easier supervision. ✨👁️ 🛤️🔥 Guide rails + automatic hood Heat hood runs only during loading to reduce temperature loss, automatic rail infeed improves ergonomics and loading speed. 🙌⚙️ 🎛️🌡️ MULTI-ZONE HEAT Independent zone control for uniform curing of parts with different mass and geometry. 🧩✅ 🧠♨️ MTS system Heating elements mounted without thermal bridges - higher efficiency and faster time to set temperature. ⚡⏱️ 2-in-1 🧱↔️🧱 Split chamber Movable partition for two independent zones - drying and curing in one unit for maximum flexibility. 🚀🔁 🎚️🌀 VFD ventilation Variable fan speed based on chamber conditions - better control and lower electricity use. ⚙️💡

Condition: new, Year of construction: 2025, Curing ovens shown in the photos can vary in price depending on size, configuration, and optional features. 💡📏⚙️ At ROMER, we manufacture both standard models and fully bespoke solutions, tailored to your process requirements. 🏭✅ Tell us your part size, line capacity, curing profile, and available space - and we will propose the best setup and the options that actually improve daily performance. 🔥🎯 🧠📡 Control and monitoring Live process control for temperature, time, airflow, and modes - with alarms and saved recipes for repeatable cycles. 🔁✅ 🔥🧩 Heating module Fast heat-up and stable temperature thanks to efficient heating elements and quick energy transfer. ⚡🌡️ 🌀💨 Air circulation Uniform airflow reduces temperature differences for consistent coating quality. 🎯✅ 🧱❄️ Insulation and design Smart chamber construction minimizes heat loss - faster reaching setpoint, lower consumption. ♻️📉 🛡️⚠️ Safety and certification Sensors, interlocks, and protection logic increase safety and reliability. 🔒👷 ⚡💰 High efficiency Optimized heat transfer and reduced losses mean real operating savings. 📉🔥 ⏰🤖 Automatic start Programmable schedule - automatic preheating before the shift for smoother production starts. ⏱️✅ Isdpjyg H Dhjfx Afujbc 🚪🔒 Self-latching doors + intelligent chimney Prevents accidental opening, chimney activates only when needed for safer operation. 🧯✅ 🌿🔋 ECO mode Low-energy standby when idle - fuel consumption reduction up to 20% (depending on process). 🌱📉 👀💡 View and lighting Inspection without opening the door - fewer temperature drops, easier supervision. ✨👁️ 🛤️🔥 Guide rails + automatic hood Heat hood runs only during loading to reduce temperature loss, automatic rail infeed improves ergonomics and loading speed. 🙌⚙️ 🎛️🌡️ MULTI-ZONE HEAT Independent zone control for uniform curing of parts with different mass and geometry. 🧩✅ 🧠♨️ MTS system Heating elements mounted without thermal bridges - higher efficiency and faster time to set temperature. ⚡⏱️ 2-in-1 🧱↔️🧱 Split chamber Movable partition for two independent zones - drying and curing in one unit for maximum flexibility. 🚀🔁 🎚️🌀 VFD ventilation Variable fan speed based on chamber conditions - better control and lower electricity use. ⚙️💡

Condition: excellent (used), Year of construction: 2001, functionality: fully functional, power: 0.14 kW (0.19 HP), input voltage: 230 V, type of input current: AC, volume flow: 1,890 m³/h, filter area: 7.9 m², noise level: 65 dB, actuation type: electric, total height: 575 mm, total length: 600 mm, total width: 590 mm, overall weight: 55 kg, Equipment: CE marking, documentation/manual, LTA electrostatic dust extraction system Iedpfx Aszqttcsfusbc right-hand intake, the other one has already been sold the intake nozzle can be screwed on as needed, currently none is available; it was mounted directly on the housing wall. In very good, fully functional condition, and of course, completely cleaned. Available for immediate delivery.

Condition: ready for operation (used), Year of construction: 2013, operating hours: 12,486 h, functionality: fully functional, travel distance X-axis: 3,400 mm, travel distance Y-axis: 2,300 mm, travel distance Z-axis: 1,000 mm, spindle speed (max.): 18,000 rpm, controller model: Siemens 840D sl, TECHNICAL DETAILS Travel range X-axis: 3,400 mm Travel range Y-axis: 2,300 mm Travel range Z-axis: 1,000 mm Rapid traverse X-axis: 60 m/min Rapid traverse Y-axis: 60 m/min Rapid traverse Z-axis: 40 m/min Design: C3 swivel head Swivel range C-axis: 200° Swivel range A-axis: 120° Spindle motor power: 24 kW Spindle mounting: HSK 63 A Spindle speed: 18,000 rpm Spindle cooling: Water cooling Design: Disc tool changer Tool magazine positions: 20 Pick-up positions: 1 Tool diameter: up to Ø 500 mm Table length: 2,000 mm Table width: 1,500 mm Table thickness: 30 mm Grid spacing: 100 x 100 mm Maximum load capacity: 2,000 kg Repeatability: approx. 0.012 mm MACHINE DETAILS CNC control: Siemens 840D sl Spindle operating time: approx. 12,486 hours Power-on hours: approx. 37,297 hours EQUIPMENT 5-axis package: included Advanced Surface: included TCP: included Control panel size: 15 inches Remote maintenance: prepared Workpiece measuring probe: m&h wireless measuring probe Tool measurement: BLUM laser Minimum quantity lubrication: internal and external lubrication Central lubrication: automatic Spray mist extraction: with electrostatic separation Full protective cabin: included Tool changing chamber: separate Iedpfx Afjz Izduouobc Technical documentation Operating manual Omlat spare spindle included

Year of construction: 2021, operating hours: 480 h, condition: like new (used), functionality: fully functional, Electrostatic separator (corona) - EBS-4-271200 - builded to extract the metals from the rejection of the plastic from electric cable process Including additional options: - 3 screw transporters; - 3 m3 input hopper; - mechanisms for changing material flow and stand for big bag for mix collection; - touch screen for control cabinet english / rusian language; - set of spare parts Designed for dry high-efficiency separation of materials, that are differ in their electric properties: - mixtures of plastics and metals, including shredded cables, into metal (copper, aluminium), and non-conducting material (plastic); - mixture of different materials, provided that one of the components has conducting properties (extraction oftextilecord from rubber crumb in the processing of used tires ); - shredded WEEE (including PCB’s) into metal (aluminium, copper, nickel, bronze, and other) and nonconducting materials (plastic, textolite, fiber-glass plastic, and other), and also for: - separations of non-metal raw material (feldspar, pegmatite, quartz sand); - enrichingofdroughconcentratesofores of rare metals (titan-zirconia, tantalum- niobic, tin-tungsten, monazite), ores of precious metals (gold, silver); - benefication of diamond ore. Iodpswcp I Ajfx Afuebc The equipment was purchased at the end of 2021 directly from the prestigious manufacturer PRODECOLOGIA, which also installed it in our factory. The equipment works perfectly and can be tested at any time with PVC plastic, from our Guidetti plant for electric cable recycling. Upon request, we can also provide installation + commissioning at the buyer's location. PRICE : 108 000 EURO- netto

Condition: like new (used), Year of construction: 2020, functionality: fully functional, For sale is an Oerlikon Nonwoven ecuTEC+ electrostatic charging machine, designed for the electrostatic charging of filter media. Isdpfjzumirox Afusbc The machine is intended for integration into a production line and processes material webs with a width of up to 1,700 mm. The material is guided through the machine by a system of deflection rollers and electrostatically charged using charging bars. The system is equipped with an HMI control panel and can operate in constant-current or constant-voltage mode. The machine has seen very little use and is being offered due to changes in the production setup. Manufacturer: Oerlikon Nonwoven / Oerlikon Neumag Model: ecuTEC+ Year: 2020 Application: electrostatic charging of filter media Maximum material width: 1,700 mm HMI operator panel Adjustable charging system Constant-current / constant-voltage operating modes Designed for integration into an industrial production line CE documentation available According to the manufacturer's documentation, the material is guided through the machine via seven deflection rollers and electrostatic charging takes place at four charging positions. The system includes the machine frame with safety guarding, deflection roller/charging section, electrical cabinets with control electronics and high-voltage generators, and touchscreen control panel. Condition: Used, very low operating use. The machine is currently dismantled/disconnected from the production line. Detailed technical documentation is available. A comprehensive PDF specification/manual can be provided to interested buyers upon request. Inspection can be arranged by appointment. Further information, photos and documentation are available on request.

Condition: new, Year of construction: 2025, Curing ovens shown in the photos can vary in price depending on size, configuration, and optional features. 💡📏⚙️ At ROMER, we manufacture both standard models and fully bespoke solutions, tailored to your process requirements. 🏭✅ Tell us your part size, line capacity, curing profile, and available space - and we will propose the best setup and the options that actually improve daily performance. 🔥🎯 🧠📡 Control and monitoring Live process control for temperature, time, airflow, and modes - with alarms and saved recipes for repeatable cycles. 🔁✅ 🔥🧩 Heating module Ibedpfx Asflk Awsfusc Fast heat-up and stable temperature thanks to efficient heating elements and quick energy transfer. ⚡🌡️ 🌀💨 Air circulation Uniform airflow reduces temperature differences for consistent coating quality. 🎯✅ 🧱❄️ Insulation and design Smart chamber construction minimizes heat loss - faster reaching setpoint, lower consumption. ♻️📉 🛡️⚠️ Safety and certification Sensors, interlocks, and protection logic increase safety and reliability. 🔒👷 ⚡💰 High efficiency Optimized heat transfer and reduced losses mean real operating savings. 📉🔥 ⏰🤖 Automatic start Programmable schedule - automatic preheating before the shift for smoother production starts. ⏱️✅ 🚪🔒 Self-latching doors + intelligent chimney Prevents accidental opening, chimney activates only when needed for safer operation. 🧯✅ 🌿🔋 ECO mode Low-energy standby when idle - fuel consumption reduction up to 20% (depending on process). 🌱📉 👀💡 View and lighting Inspection without opening the door - fewer temperature drops, easier supervision. ✨👁️ 🛤️🔥 Guide rails + automatic hood Heat hood runs only during loading to reduce temperature loss, automatic rail infeed improves ergonomics and loading speed. 🙌⚙️ 🎛️🌡️ MULTI-ZONE HEAT Independent zone control for uniform curing of parts with different mass and geometry. 🧩✅ 🧠♨️ MTS system Heating elements mounted without thermal bridges - higher efficiency and faster time to set temperature. ⚡⏱️ 2-in-1 🧱↔️🧱 Split chamber Movable partition for two independent zones - drying and curing in one unit for maximum flexibility. 🚀🔁 🎚️🌀 VFD ventilation Variable fan speed based on chamber conditions - better control and lower electricity use. ⚙️💡

Condition: new, Year of construction: 2025, Curing ovens shown in the photos can vary in price depending on size, configuration, and optional features. 💡📏⚙️ At ROMER, we manufacture both standard models and fully bespoke solutions, tailored to your process requirements. 🏭✅ Tell us your part size, line capacity, curing profile, and available space - and we will propose the best setup and the options that actually improve daily performance. 🔥🎯 🧠📡 Control and monitoring Live process control for temperature, time, airflow, and modes - with alarms and saved recipes for repeatable cycles. 🔁✅ 🔥🧩 Heating module Fast heat-up and stable temperature thanks to efficient heating elements and quick energy transfer. ⚡🌡️ 🌀💨 Air circulation Uniform airflow reduces temperature differences for consistent coating quality. 🎯✅ 🧱❄️ Insulation and design Smart chamber construction minimizes heat loss - faster reaching setpoint, lower consumption. ♻️📉 🛡️⚠️ Safety and certification Sensors, interlocks, and protection logic increase safety and reliability. 🔒👷 ⚡💰 High efficiency Optimized heat transfer and reduced losses mean real operating savings. 📉🔥 ⏰🤖 Automatic start Programmable schedule - automatic preheating before the shift for smoother production starts. ⏱️✅ 🚪🔒 Self-latching doors + intelligent chimney Prevents accidental opening, chimney activates only when needed for safer operation. 🧯✅ 🌿🔋 ECO mode Low-energy standby when idle - fuel consumption reduction up to 20% (depending on process). 🌱📉 👀💡 View and lighting Inspection without opening the door - fewer temperature drops, easier supervision. ✨👁️ 🛤️🔥 Guide rails + automatic hood Heat hood runs only during loading to reduce temperature loss, automatic rail infeed improves ergonomics and loading speed. 🙌⚙️ Ibsdjfz U Nbspfx Afuoc 🎛️🌡️ MULTI-ZONE HEAT Independent zone control for uniform curing of parts with different mass and geometry. 🧩✅ 🧠♨️ MTS system Heating elements mounted without thermal bridges - higher efficiency and faster time to set temperature. ⚡⏱️ 2-in-1 🧱↔️🧱 Split chamber Movable partition for two independent zones - drying and curing in one unit for maximum flexibility. 🚀🔁 🎚️🌀 VFD ventilation Variable fan speed based on chamber conditions - better control and lower electricity use. ⚙️💡

Condition: ready for operation (used), We offer a ready for use hamos EKS 1031 electrostatic separator for plastics. This machine is designed for efficient separation of mixed plastic materials using electrostatic technology. Ideal for recycling and industrial processing applications. Condition: ready for use Voltage: 400 V Frequency: 50 Hz Type: EKS 1031-0 The machine is in good working condition. Inspection possible. Isdpfxjyv Hzas Afuobc Location: Lithuania For more information, please contact us.

Condition: ready for operation (used), Year of construction: 2007, operating hours: 61,700 h, functionality: fully functional, machine/vehicle number: 7831, spindle motor power: 5,500 W, turning length: 231 mm, spindle speed (max.): 10,000 rpm, turning diameter: 25 mm, spindle bore: 25 mm, overall weight: 3,000 kg, rotational speed (max.): 10,000 rpm, type of input current: three-phase, feed length Y-axis: 534 mm, feed length Z-axis: 230 mm, total width: 1,400 mm, total length: 2,400 mm, total height: 2,060 mm, feed rate X-axis: 30 m/min, feed rate Y-axis: 30 m/min, feed rate Z-axis: 30 m/min, bar diameter (max.): 25 mm, quill travel distance: 230 mm, quill diameter: 25 mm, rapid traverse X-axis: 30 m/min, rapid traverse Y-axis: 30 m/min, rapid traverse Z-axis: 30 m/min, input voltage: 400 V, power: 5.5 kW (7.48 HP), travel distance X-axis: 58 mm, travel distance Y-axis: 534 mm, travel distance Z-axis: 230 mm, operating pressure: 6 bar, Equipment: documentation/manual, rotational speed infinitely variable, Tornos Deco SIGMA 20s Swiss-type automatic lathe, including Robobar SBF-532 3000mm bar feeder, Mayfran Consep chip conveyor with drum filter (unique version), electrostatic oil mist collector, and an automatic CO₂ fire suppression system (Kraft & Bauer). Fitted with a Fanuc 31i-model A CNC control, spindle speeds up to 10,000 RPM on both the main and sub spindles. The machine features 6 axes and 22 tooling positions: Main spindle: 12 positions, 6 of which are driven (up to 6,000 RPM) Sub spindle: 10 positions, 6 of which are driven (up to 6,000 RPM) Also equipped with high-pressure coolant, up to 80 bar. The machine can be inspected under power. Dismantling and transport are the responsibility of the buyer. Parts included with the machine: • External holder left, long – 6× (417608) • External holder left, short – 1× (417606) • Single driven holder, reduced speed – 2× (417612) • Double clamping, long – 2× (417617) • Double clamping, short – 2× (417620) Ibodpfoyrg Ahex Afuoc • Driven block – 2× (417624) Bushings for pusher diameters (216787): • Ø10 • Ø16 • Ø20 • Ø25 Ejector set: • Ø5 to Ø20 (in 1 mm increments)

Year of construction: 2020, condition: new, 7" Touchpad Large color touch panel looks aesthetically and uses comfortably and intuitively. Set on it all the important parameters.Memory 20 programs each with 10 events You can save up to 20 programs and activate up to 10 consecutive events time-temperature arranged in the heating curve. This is especially needed for the more demanding process.Information about consumption of power Consumption is calculated based on the settings of the burner. This feature will allow you to estimate the cost of the cycle, consumption and plan check staff.Recorder of cycle USB Each of the ovens is equipped with two-channel temperature recording on USB flash drive.. Each file is automatically created and is responsible for a separate cycle are recorded temperature extremes, hour and minute measurement. Files are saved in * .csv (Excel sheet) For all buyers the end of 2016 option is free, the competition for the option you have to pay up to several thousand euros. History 20 latest of burn Iedsfz U Tispfx Afuebc Something's wrong? and perhaps too few overbroad elements from the oven? Now you check thoroughly oldest and lastest burning parameters, how often took, whether cycle proceeds without any problems, what was the consumption and when they ran. Start the oven automatically at 6 am How many times have you stay after hours and expecting end of the cycle? If you own a powder coating plan that works for a long time, You know exactly what we are talking about. With our solution you can leave cycle not cured in the oven, to automatically end when you come to the job next morning.

Condition: ready for operation (used), Year of construction: 2006, functionality: fully functional, machine/vehicle number: 2441.05, cutting force: 1,122 t, total width: 9,000 mm, total length: 19,000 mm, total height: 5,700 mm, overall weight: 320,000 kg, operating pressure: 350 bar, loading space height: 1,800 mm, cutting width (max.): 810 mm, DGUV certified until: 11/2026, ejection height: 850 mm, filling opening length: 7,500 mm, filling opening width: 2,300 mm, The described scrap shear from Leimbach, including the associated conveyor belt, is for sale. The machine is in operation. An inspection at our facility is possible by prior arrangement in 68219 Mannheim. In addition to the existing oil filtration system, an electrostatic oil purification system from Kleentek has been installed. The machine is available upon agreement. Further information is available upon request. Delivery terms: EXW Mannheim, Rheinauhafen. The dismantling of the goods and its subsequent loading onto the means of transport will be carried out at the buyer's expense and risk. The selling price and delivery terms are negotiable. The sale is exclusively to commercial customers. This offer is non-binding and is subject to a technical and legal review as well as a contractual agreement between the parties. Isdozzxbtspfx Afuebc

Condition: excellent (used), Year of construction: 2014, 2014 Schneeberger Sirius HPM 6-Axis Tool Grinding Machine With Fanuc Series 31I-Model A5 CNC Control Ibodoz E R T Hspfx Afusc Gear Tooth Production Steptec GFQ 170E Swivel Spindle Workhead. Travel: 'X' Axis = 420mm, 'Y' Axis = 310mm, 'Z' Axis = 340mm. 'A' Axis (Rotation) = 2,400°/S. ISO40, Centre Height 150mm. Swivel Axis 'B' = 90°, Swivel Axis 'C' = 180°. (1) Hitema Stand Alone Air Cooled Liquid Chiller Type ENR.018/CX.SST.WP.HW.RV.DD.GALV (340kg, 2020). (1) Hyfra Pedia Sigma 13-S Stand Alone Water Cooling Chiller (200kg, 2014). VAS 7041, 400 Litre Stand Alone Filtration System (800mm x 1,300mm x 600mm, 400kg). Sirius S/No. 21828. Quantity of Assorted Arbors, Collets, Grinding Attachments & Associated Tooling to Suit. Probe, Machine Light & Signal Tower. New Battery Fitted 2025. Kraft Bauer Fire Extinguishing System. Elbaron Ronia 100 DV Electrostatic Air Cleaner/Mist Collector. Cosmotec EVE10082207000 7035 Air Conditioner (2013). Power Supply 415 Volt, 3 Phase. Full Catalogues & Manuals Available. Weight of Machine Approx 8,100kg. Dimensions of Machine Approx 1,700mm x 2,270mm x 2,215mm. Note: Client will arrange for the machine to be disconnected and drain the oil (if required) and move to the Exit for collection. During viewing, Client is willing to demonstrate the machine capabilities.

Condition: ready for operation (used), Year of construction: 2004, functionality: fully functional, • Year 2004 • In our possession since 06/2023 • Complete clamping system, with two modified clamps for Ø14 and Ø16 • Automated pallets with diameters of Ø3, Ø4, Ø6, Ø10, Ø12 • Various grinding wheels for roughing and finishing, some new, for both carbide and HSS • Parkair electrostatic dust extractor • New user interface keyboard (3-4 years old) • New workpiece rotation belt (replacement due in 2025) • Less than 100 operating hours since 2023 • Dedicated Transor filtration tank, year 2007, maintained with filter changes and complete functionality check, with service performed in 07/2023 (over €3000 + VAT), less than 100 operating hours since the maintenance -separate sale can be considered- Ibedpfozcvakjx Afuoc • Machine price: €25,000 - Filtration system price: €10,000

Condition: used, Year of construction: 2011, operating hours: 2,200 h, functionality: fully functional, power: 7.5 kW (10.20 HP), year of last overhaul: 2026, We offer this used Schneeberger Norma CFG 7.5 kW tool grinding machine, manufactured in 2011, for sale. OPERATING HOURS: 2200! Automatic programmable central lubrication system Pneumatic hoses completely renewed 4/2026 Standard version PLUS: - Hydraulic quick tool clamping system - Grinding wheel spindle HSK 50 - Quinto-Basic-SW woodworking tools - Coolant filter unit 330l; 6.3 bar Ibjdpfxezqu Tdo Afujc - CO² fire protection system Special accessories: - Manufactured in 2013 - Workpiece loader MIL incl. quick-change tool holder for profile cutters and shank tools - 1 piece of pallet for profile cutters - profile thickness: 2mm; plate width up to 150mm Machine Specifications – NORMA CFG (Schneeberger Invoice No. 88088, dated 21.12.2011) MAIN MACHINE M-55039-0031 – CNC Tool Grinding Machine "NORMA CFG" Power: 7.5 kW Machine No.: 21'692 Voltage: 400V / 3-phase / 50Hz EQUIPMENT & OPTIONS M-51019-0021 – Automatic programmable central lubrication M-50019-0022 – Precision 3D touch probe PSM 118 M-82090-0003 – Network connection M-56009-1993 – Remote maintenance software, 2 years free M-50009-0191 – Dressing roller on mounting arbor M-530890098B – Hydraulic quick tool clamping, ISO 50 M-10030-0115 – Expansion collet chuck ISO 50, D=20 M-10030-0116 – Expansion collet chuck ISO 50, D=32 M-56039-0044B – Plate mount, hydraulic, horizontal M-50020-0211B – Intermediate layer 40 M-50020-0003B – Intermediate layer, standard M-56009-0643 (x6) – Grinding wheel mount HSK50, 20/70x85 M-45000-0000 – Quinto base software M-45000-0010 – Quinto standard tools M-45001-0210 – Quinto software eGrind viewer M-45000-7030 – Quinto software dxQ, woodworking inserts M-45001-0010 – Quinto easyPROFILE M-45000-1010 – Quinto software, woodworking tools M-50009-0190A – Flow monitor M-50019-0049 (x6) – Complete plate with coolant pipes M-55039-0059 – Coolant filter unit, 330 L, 6.3 bar M-50009-0036 – CO2 fire suppression system M-55039-0086 – Electrostatic extraction/suction unit M-600000-051 – Training in Roggwil/Weissach, 3 days M-600000-052 – Installation and follow-up training, 3 days in Gütersloh M-20000-0032 – Truck packaging M-20000-0050 – Transport incl. transport insurance (not unloaded), DAP DE-Gütersloh If you have any questions or need further information, please feel free to send us a message.

Condition: like new (used), functionality: fully functional, Year of construction: 2015, total length: 1,290 mm, total height: 1,980 mm, total width: 900 mm, type of input current: three-phase, overall weight: 658 kg, input voltage: 240 V, input current: 40 A, temperature: 160 °C, input frequency: 50 Hz, ambient temperature (min.): 15 °C, ambient temperature (max.): 30 °C, positioning accuracy: 0.127 mm, electrical fuse: 40 A, repeat accuracy: 0.05 mm, feed length X-axis: 406 mm, feed length Y-axis: 355 mm, feed length Z-axis: 406 mm, space requirement length: 2,000 mm, space requirement height: 2,200 mm, noise level: 65 dB, space requirement width: 1,500 mm, High-performance industrial 3D printer based on FDM technology, designed for functional prototyping and low-volume production using certified engineering thermoplastics. The Stratasys Fortus 450mc is a proven platform for companies requiring repeatability, dimensional stability, and material traceability, making it suitable for automotive, aerospace, industrial equipment, and advanced R&D environments. The system is configured with dual extrusion heads in open material mode, enabling advanced process flexibility and compatibility with a broader range of FDM-grade thermoplastics, subject to parameter optimization and the thermal constraints of the platform. Key Features: - Heated build chamber (up to ~180°C) for superior layer adhesion and reduced warping - Industrial-grade repeatability for functional and end-use parts - Large build volume: 406 × 355 × 406 mm - Dual extrusion system (model + soluble support) - Closed material system for process stability and consistency - Compatible with Insight software for advanced process control Supported Materials: 🔹 Standard & Functional Polymers ABS-M30 → robust functional prototyping ASA → UV-resistant outdoor applications ABS-ESD7 → electrostatic dissipative components Ibedpey Ug Ecefx Afujc 🔹 High-Performance Polymers PC (Polycarbonate) → high impact resistance PC-ABS → balance between toughness and processability 🔹 Advanced Engineering Materials Nylon 12 (PA12) → wear resistance and fatigue durability Nylon 12CF (carbon fiber reinforced) → increased stiffness and dimensional stability 🔹 Aerospace-Grade Thermoplastics ULTEM 9085 → FST compliant (flame, smoke, toxicity) ULTEM 1010 → maximum thermal resistance and mechanical strength

Condition: ready for operation (used), Year of construction: 1999, • Year 1999 • In our possession since 08/2024 • Quinto 4 software • Electrostatic filter, Elbaron model • Numerous spindles • Recent maintenance performed: external cleaning and repainting, spindle overhaul, spindle belt replacement, brush and front plexiglass replacement, wheel and door rail replacement, machine measurement, offset adjustment, ball reference setting, backlash check, replacement of the air filtration and lubrication adjustment unit, replacement of 4 electric fans. Ibedpfxszcvaqo Afuec

Condition: like new (used), Year of construction: 2022, functionality: fully functional, complete plat concisting of: Bi-rail overhanging conveyor with two points bar support , lift and rotation unit Spray booth for robot with full recirculation, with autimatic pre-filter replacment system High pressure humidificer for spray booth and flash off room Robotic spray system for windows with jacket nozzle cleaning unit automatic color change (3 independent ) electrostatic safty system paint flow meter Ibjdoxw Ux Hopfx Afuec drying tunnel with ldp system and axial fans supervisor systeem with data interface and datamic reader “The line is packed for transport. It has been previously installed, but it has never been taken into operation.”

Condition: excellent (used), PRO XP85 MANUAL ELECTROSTATIC SPRAY GUN GRACO REF. L85T10 Isdjivt Rijpfx Afuebc - Brand: GRACO - Reference: L85T10 -PRO XP85, Standard, BOQ. 1.5MM., 85KV. -Industry in general, metal, wood -Does not include hose, avaliable under demand - Second-hand product that has passed a very rigorous tuning - 1 year warranty. It is in like-new condition - VAT not included

Condition: ready for operation (used), Year of construction: 2010, functionality: fully functional, total length: 9,000 mm, working height: 120 mm, For sale: BARBERAN PUR-33-L profile wrapping machine (year 2010) – machine for laminating elements with decorative foil using PUR hot-melt adhesive (hot gluing). The machine features a single foil feeder, automatic control, and an added antistatic corona system (reduces electrostatic charges – improves foil feed stability). Technical specifications: Ibodpfx Afsyw Nxkousc Model: BARBERAN PUR-33-L Year of manufacture: 2010 Machine length: approx. 9 m Max. element width: 120 mm Feed speed: up to 45 m/min Power supply: 400V / 50Hz Foil feeder: 1 unit Equipment / additional features: Antistatic corona (retrofitted) – neutralizes foil static Printer – enables edge printing (e.g. strip name / operator / description) Glue melter with approx. 60L capacity – allows extended operation without interruption. Important: The machine applies PUR adhesive using hot-melt technology Heaters are NOT included in the set.

Condition: excellent (used), Year of construction: 2011, operating hours: 31,648 h, functionality: fully functional, machine/vehicle number: 90265 2011, saw blade diameter: 710 mm, tooth pitch: 55 mm, grinding wheel diameter: 200 mm, total width: 2,662 mm, total length: 2,540 mm, total height: 2,640 mm, type of input current: AC, input current: 10 A, input frequency: 50 Hz, disc diameter: 200 mm, grinding wheel bore: 32 mm, grinding spindle motor power: 3,000 W, saw blade width: 8 mm, input voltage: 400 V, overall weight: 3,200 kg, saw blade bore: 80 mm, power: 10 kW (13.60 HP), grinding diameter: 710 mm, workpiece diameter (max.): 710 mm, Equipment: rotational speed infinitely variable, CNC saw blade sharpening machine with lateral tooth divider grinding device and saw blade magazine for blades up to D=560 mm for unmanned operation. In manual mode: 40–710 mm. Saw blade magazine with 3 holding arbors. Oil filtration system for HSS, oil cooler brand Polar 2.9. Tooth geometries HSS: Form A, B, BW, C and special tooth forms. Saw blade holders for manual loading D=75 to 250 mm and D=40 to 100 mm. Special program for grinding variable tooth pitches. CAD program for creating up to 250 custom tooth shapes. Fire extinguishing system is an oil retrofit kit with aerosol extinguishing generator. With electrostatic air extraction. Ibedpfxsx Tct To Afusc

Condition: used, Year of construction: 2016, functionality: fully functional, machine/vehicle number: 46003, Technical characteristics: Work Area # Maximum diameter of the clamping plate: 220 mm # Maximum turning diameter: 170 mm Isdpfx Afexw Ub Ijusbc # Maximum machining diameter: 170 mm # Maximum workpiece length: 100 mm # X-axis travel: 495 mm / Rapid feed in X: 48 m/min # Z-axis travel: 250 mm / Rapid feed in Z: 30 m/min # Standard enclosed automation (number of loading stations by workpiece diameter: 14/(80–200 mm), 18/(30–160 mm), 30/(30–85 mm)) Main Spindle # Spindle interface to DIN 55026: Size A5 # Maximum speed: 7000 rpm # Power at 100% duty cycle: 23 kW # Torque at 100% duty cycle: 130 Nm Powered Tool Turret # Turret type: VDI40, Siemens drive 0.5.435.220, Manufacturer: Sauter # Number of stations: 12 # Maximum speed: 4000 rpm Electrical Equipment # Operating voltage: 400 V, fuse protection 80A GL # Connected load: 41 kW Dimensions # Total dimensions: Length = 3913 mm, Width = 2160 mm, Height = 2955 mm # Weight: 6500 kg Main Features and Capabilities: # Vertical design: Optimal chip evacuation and easy loading/unloading # CNC control: Siemens 840D SL # High precision: Positioning in X and Z axes via Heidenhain linear encoders # Main spindle - Manufacturer: Weiss, providing high power and wide speed range # Automated loading/unloading: Integrated automation supplies and removes parts # In-process probe: Marposs T25 # Live tooling: Allows drilling and milling operations in addition to turning # Chip conveyor: Knoll # Coolant filtration and cooling: Knoll KF150/950 paper filtering unit # Fire suppression system: Kraft & Bauer # Electrostatic oil mist filter: IF Vario EC1500 Machine status: WORKING

Condition: used, Year of construction: 2016, functionality: fully functional, machine/vehicle number: 46001, Technical characteristics: Ibsdpfxsxw Ufyo Afusc Work Area - Maximum clamping plate diameter: 220 mm - Maximum turning diameter: 170 mm - Maximum machining diameter: 170 mm - Maximum workpiece length: 100 mm - X-axis travel: 495 mm / X-axis rapid traverse: 48 m/min - Z-axis travel: 250 mm / Z-axis rapid traverse: 30 m/min - Standard enclosed automation (number of loading positions by workpiece diameter: 14/(80...200), 18/(30...160), 30/(30...85)) Main Spindle - Spindle (DIN 55026): Size A5 - Maximum speed: 7000 rpm - Power at 100% duty cycle: 23 kW - Torque at 100% duty cycle: 130 Nm Tool Turret with Driven Tools - Turret VDI40, Siemens drive 0.5.435.220, Manufacturer: Sauter - Number of stations: 12 - Maximum speed: 4000 rpm Electrical Equipment - Supply voltage: 400 V, 80A GL fuse protection - Connected load: 41 kW Dimensions - Total dimensions (L×W×H): 3913 × 2160 × 2955 mm - Weight: 6500 kg Main Features and Capabilities: - Vertical design: Optimal chip evacuation and easy loading/unloading - Control system: Siemens 840D SL - High precision: X and Z axis position accuracy via Heidenhain linear scales - Main spindle by Weiss: High power and broad speed range - Automated loading/unloading: Parts are loaded and unloaded via integrated automation - In-process control probe: Marposs T25 - Driven tools: Enables drilling and milling operations - Chip conveyor: Knoll - Coolant “paper” filtration & chiller unit: Knoll KF150/950 - Fire suppression system: Kraft&Bauer - Electrostatic mist collector: IF Vario EC1500 Machine status: - Working

Condition: like new (used), Year of construction: 2021, functionality: fully functional, total height: 3,000 mm, total length: 8,880 mm, total width: 4,000 mm, volume flow: 38,000 m³/h, type of input current: three-phase, workpiece weight (max.): 80 kg, compressed air connection: 8 bar, suction capacity: 38,000 m³/h, load capacity: 80 kg, heating capacity: 340 kW (462.27 HP), Equipment: cabin, lighting, For sale is a brand new wet painting line. Internal dimensions of the cabin 8880x4000x3000mm. Overhead conveyor of products with a length of 41m. Pitch of swivel hinges 400mm. Load capacity 80kg/m. Production speed maximum 4m/min. Large door to the cabin 2000x2500mm (possibility of painting large parts). Ventilation exhaust unit 38,000m3/min. Paint preparation room including membrane pump 01D140. Application electrostatic gun. Gas heating 340kW. Iodpfx Aswmm U Uefuebc