Used Eisele Kms for sale (113)

Condition: used, saw blade diameter 275 mm cutting diameter bis 90 mm cutting range flat 120 x 75 mm turning speeds 40/80 U/min miter cut 45°/90°/-45° ° weight of the machine ca. ca. 150 kg Manual saw blade feed Accessories: Coolant device Underframe with 2 drawers Gbedpowglgisfx Aaxsl

Condition: used, Year of construction: 1979, saw blade diameter 300 mm cutting diameter 100 mm saw blade turning speeds 40 / 80 U/min Gbedpfx Aajy N D Nnjxsl capacity 90 degrees: square 90 mm capacity 90 degrees: round 100 mm total power requirement 1,5 kW weight of the machine ca. 0,5 t

Condition: excellent (used), Year of construction: 2003, Max. saw blade diameter: up to 300 mm Machine head tiltable: 45°-90°-45°-30° Cutting diameter at 90°: 100 mm Square tube: 85 x 85 mm Flat profiles, hollow: 130 x 85 mm Speed range: 40 / 80 rpm Drive power: 1.0 / 1.2 kW Machine dimensions (L x W x H): 650 x 600 x 1650 mm Weight: 185 kg Accessories / Special Features: Gjdpfsy E Ullox Aaxjbl • Vertical guidance of the saw head • Continuously adjustable mitre facility 45°-90°-45°-30° • Infeed/outfeed roller conveyors, each approx. 1 m in length • Manual feed • Coolant system • 1 saw blade included • CE compliant This very good VMS 300 is from a training workshop. Siegfried Volz Machine Tools Rüschebrinkstr. 151-153 DE - 44143 Dortmund - Wambel / Germany

Year of construction: 2009, condition: used, Sawing system for aluminum with 2 saw motors that independently perform a 45° cut. Gedpfxoqzmnue Aaxobl Material feed unit with up to 8,100 mm Cross conveyor, storage table, chip conveyor and extraction Soundproof cabin Control via Siemens S7 panel Operating instructions etc. available, further technical data on request Machine was in operation until dismantling Further technical data on request or see photos

Condition: good (used), Year of construction: 2012, machine/vehicle number: 10004373, Offer 26126 Technical specifications: - Manual saw blade feed Gbodjy Rz S Nepfx Aaxol - Workpiece clamping via machine vice - Saw blade diameter up to 315 mm - 2 cutting speeds: 40 – 80 m/min - Cutting range at 90°: round 110 mm; rectangular 82 x 160 mm; square 82 x 82 mm - Miter cut at 45°: round 110 mm; rectangular 80 x 120 mm; square 82 x 82 mm - Drive: 400 V / 1.4 / 1.9 kW - Coolant system - Space requirements approx. W 600 x H 1600 x D 750 mm - Weight approx. 300 kg - Measuring stop: 3000 mm

Condition: good (used), Year of construction: 2002, Behringer Eisele VA-0-250-NC Circular saw TECHNICAL DATA Sawing range: 90 ° Saw blade diameter: 25 cm Bore: 40 mm Cutting range: 10-75 mm Cutting length: 5-900 mm Speed: 2800 rpm Cutting speeds: 26/52/103/206 SFPM or 0.13/0.26/0.52/1.05 m/s Feed speeds: 0-40 mm/sec NC axis: Yes Dimensions: 190 x 127 x 190 Weight: 1300 kg We assume no liability for the accuracy, completeness and up-to-dateness of the information provided Gsdpfx Aevdk A Esaxsbl

Condition: excellent (used), Year of construction: 2017, functionality: fully functional, Very well-maintained Behringer VMS 370 A, including infeed and outfeed roller conveyors. The machine is now in stock, refurbished, and available for immediate delivery. Gjdpfx Aoy Edcysaxebl

Condition: used, Year of construction: 1994, functionality: unexamined, machine/vehicle number: 171982, saw blade diameter: 350 mm, main saw diameter: 350 mm, We offer this used EISELE LMS 350 P cut-off saw, year of manufacture 1994. Manufacturer: EISELE Gedpfxoy D H Dwj Aaxobl Model: LMS 350 P Serial number: 171982 Year of manufacture: 1994 Voltage: 380 V With double-button control and pneumatic clamps Equipped with a wood blade If you have any questions or need further information, please feel free to send us a message or give us a call.

Condition: good (used), Year of construction: 1994, machine/vehicle number: A 3883, Offer 24310 Gsdjy Nlthepfx Aaxobl Technical Data: - Manual saw blade feed - Workpiece clamping in machine vice - Saw blade diameter: 315 mm - 2 cutting speeds: 40 - 80 m/min - Cutting capacity at 90°: round 110 mm - Rectangular 82 x 160 mm - Square 82 x 82 mm - In mitre at 45°: round 110 mm - Rectangular 80 x 120 mm - Square 82 x 82 mm - Drive: 400 V / 1.4 / 1.9 kW - Coolant system - Required space approx. W 600 x H 1600 x D 750 mm - Weight approx. 300 kg

Condition: used, 1 piece of mitre saw EISELE VMSA-LO Voltage: 380 Volt, on pallet Colour: as depicted, according to images and inspection Condition: used Warehouse location: storage hall Godpfxoy D Nbxs Aaxebl Payment method: advance payment by bank transfer Shipping: collection only from location Ditzingen-Heimerdingen

Condition: used, Year of construction: 1990, saw blade diameter 300 mm cutting diameter 90 mm turning speeds 40/80 U/min total power requirement 1,5 kW Gbodpfx Aasy Ehx Eoxjl weight of the machine ca. 350 Kg dimensions of the machine ca. 0,9 x 0,8 x 1,5 m Cold circular saw - Machine light - Coolant system

Year of construction: 2009, condition: used, Drive with 3 milling motors ensures a very stable structure (steel profiles can be machined from 3 sides in a single clamping). Locking mechanism for the lift of the horizontal motors prevents profiles from being scratched when inserting and removing them. Processing of profile widths up to 300 mm possible (e.g., mailboxes) using only the vertical milling motor. Specification: - Equipped with 1 vertical and 2 horizontal milling motors - Pneumatic workpiece clamping with 2 horizontal clamping cylinders - 3 pneumatic spray nozzles Gbedpjy Nm Erefx Aaxol - Milling area of the vertical motor (L x D): 365 x 230 mm - Milling area of the horizontal motors (L x H): 250 x 100 mm - Maximum profile height: 150 mm - Operation via switches and 4 hand levers

Condition: good (used), Corner joining machine, hydro-pneumatic, for aluminium window profiles up to 210 mm total height (max. punching height 150 mm) incl. 2 sets of standard punching knives, height adjustable; pneumatic hold-down cylinders; retractable stop; 2 swivelling profile support arms; operation via 2 foot pedals. Gbsdpfxoy Nm Dbe Aaxjl

Year of construction: 2004, condition: excellent (used), functionality: fully functional, Notching saw for cut-outs and bevel notching. The machine is equipped with two saw blades, each with a diameter of 500 mm. It features a pneumatic clamping device. The feed is hydropneumatic and is triggered via two-hand control. The material stop is swiveling, with locking points and a digital display. Notching height and angle are motorized and digitally indicated. Max. profile height: 280 mm Max. notch width: 300 mm Max. notch height: 185 mm Max. notch depth: 185 mm Gbsdpfxoyzcpdj Aaxel

Condition: excellent (used), functionality: fully functional, Large fully hydraulic EISELE: Weight approx. 0.75 t, saw blade 440 mm Speeds: 12.5 / 25 rpm Gbodpfxey Ncfus Aaxsl Motor power: 2.6 / 3.2 kW Hydraulic saw feed Hydraulic vice Cutting ranges: 200 x 100 mm (square tube) Mitre cut one-sided 45°.

Year of construction: 1998, condition: used, Longitudinal cutting saw for cutting aluminum profiles with feed pusher in very good condition Gbsdpfx Aaswx I Hvexol Max. cutting length: 700 mm Max. cutting height: 130 mm Max. saw blade diameter: 450 mm Push-in length of the material pusher maximum 6,200 mm System is dismantled in our warehouse Further technical data on request

Condition: like new (used), Year of construction: 2023, operating hours: 1,809 h, functionality: fully functional, machine/vehicle number: 1559, saw blade diameter: 550 mm, feed length X-axis: 800 mm, total length: 2,400 mm, total width: 2,000 mm, total height: 1,800 mm, cutting range round steel at 90°: 190 mm, type of input current: three-phase, rotational speed (max.): 2,850 rpm, cutting height (max.): 150 mm, overall weight: 1,650 kg, section length (min.): 3 mm, section length (max.): 4,000 mm, saw blade speed: 2,850 rpm, input voltage: 400 V, saw drive: 7,500 W, cutting diameter: 270 mm, saw blade bore: 40 mm, Circular Saw Fully Automatic PROFILMA 502 + Chip Extraction MG 3 Gbsdpfx Aaey Dtpmexsl ST Circular Saw Fully Automatic PROFILMA 502 Fully automatic operation, 7.5 kW drive, S6, 400 V, 50 Hz, 2850 rpm. Suitable for saw blades Ø 550 mm, cutting capacity 270 x 150 mm (width x height), Ø 190 mm. Max. profile width 270 mm. Equipped with Siemens S7 controller with touch display incl. piece counter. Includes CPU 315 and Flexisoft, batch multiplier for bundle material processing. Cycle time indication in seconds, chain dimensions, includes reversing device for cut lengths up to 4 m max. Automatic shut-off via limit switch at end of material, fault diagnostics, including IXON router for VPN connection (see datasheet). Motorized saw blade feed, steplessly adjustable, vertical and horizontal clamping from bottom to top (both on feed and discharge side of saw head). Cutting gap extension on both sides of the saw blade. Electronic material feed unit with 800 mm feed length, utilizing ball screw and servomotor, including pneumatic horizontal and vertical clamping system. The profile support area in the feed zone is equipped with a lift/lower roller. Remnant cut from 75 mm, profile-dependent. Clamping pressure reduction horizontally and vertically with 6 pressure regulators. Intermittent spray device with level monitoring and automatic shut-off, 1-liter lubricant reservoir. Noise protection package—frame interior lined with soundproofing mats. Two extraction nozzles Ø 100 mm. Safety guard over both the saw head and the feed unit. 740 mm roller conveyor with intrusion guard on the infeed side, 450 mm pertinax tabletop with intrusion guard on the outfeed side. MG 3 Chip Extraction Dust and chips are collected in a 172-litre metal container, which is removable for easy emptying. Two outlets with 100 mm hose adapters (no extraction hose included). 3.0 kW drive, 400 V, 50 Hz, three-phase motor. Max. air flow rate 2,600 m³/h, vacuum 30 mbar, with fan snail housing above the extractor. Large filter surface, pneumatic shaker unit for filter cleaning, filter class M. Max. noise level 80 dB(A). Selector switch for continuous operation or saw-controlled operation (no power cable). Painted: RAL 7035 / 9016.

Condition: excellent (used), Year of construction: 1966, I sell a circular saw made in Germany. Company Eisele model vms II in good condition Gedpfevbwfnsx Aaxobl

Condition: used, Year of construction: 1971, functionality: fully functional, machine/vehicle number: 3229, type of input current: three-phase, rotational speed (min.): 35 rpm, rotational speed (max.): 70 rpm, input voltage: 500 V, For sale is a robust metal circular saw from the manufacturer Eisele, model VMS III. This machine is a classic cold circular saw designed for industrial use and stands out due to its solid construction and durability. Ideal for workshops, metal fabrication, or locksmith operations. Technical data: • Manufacturer: Eisele • Type: VMS III • Year of manufacture: 1971 Gbjdpfx Aasy Dc I Ssxsl • Machine number: 3229 • Rotational speeds: 35 / 70 rpm • Voltage: 500 V • Motor power: approx. 1.8 to 2.6 kW • Frequency: 50 Hz • Version: Three-phase current • Equipped with a vise and mechanical feed Condition: Used condition, appropriate for its age. The machine is of heavy-duty construction and well-suited for refurbishment or immediate use. Visually with signs of wear.

Condition: ready for operation (used), Year of construction: 2013, Circular Metal Saw manufactured in 2013. This PRESSTA EISELE Profilma 400 V features a saw blade diameter of Ø400 mm and a powerful motor with approximately 12 kW. It offers automatic material feeding and a pneumatic clamping system for efficient operation. If you are looking to get high-quality cutting capabilities, consider the PRESSTA EISELE Profilma 400 V machine we have for sale. Contact us for further details regarding this machine. • Design: Integrated material feed/loading magazine; floating feed to compensate for profile deviations • Power supply: 400 V / 50 Hz Gedpfxoyyxxfe Aaxebl • Materials: Aluminum and non-ferrous metal profiles • Saw blade diameter: Ø400 mm • Saw blade speed: adjustable approx. 3,500–5,800 rpm • Saw movement drive: Servo motor with ball screw drive • Sawing direction: Linear feed from top to bottom • Cutting principle: Crosscut • Material feed: Automatic servo feed with repeat strokes for longer cutting lengths • Material separation: Before the saw blade retracts (no recutting) • Clamping system: Pneumatic, vertical and horizontal, on both sides of the saw blade; clamping force separately adjustable; replaceable plastic/PVC pads • Control: PLC-based; operation via control panel with display • Functions: Profile database; piece counter (incl. bundle cutting); cycle time display; diagnostics and error messages; machine status indicator • Saw blade lubrication: Minimum quantity lubrication (spray mist), programmable lubrication control • Extraction connections: Ø100 mm and Ø160 mm • Pre-installation: Prepared for external chip extraction • Motor Power: up to 22 kW (multi-speed motor: 3.5 / 11.5 / 18.5 / 22 kW) Additional equipment • External chip extraction unit (to connect to Ø100/Ø160 mm ports)

Year of construction: 1996, condition: used, Hydropneumatic operation Punching force: 50 kN Work hub: 35 mm Overhang: 110 mm Installation height: 140 mm Gedpfx Aajyxpw Nexsbl

Year of construction: 2009, condition: used, Saw blade diameter vertical: 600 mm Saw blade diameter (horizontal): 500 mm Ejecting width: processing of profiles up to 300 mm at 90°, mitre tips up to 30° Profile height max. 280 mm Engagement depth: at 90° horizontal up to 185 mm / at 90° vertical up to 230 mm Material stop: swiveling 30° - 90° - 45° Gbodpfxoywtqdj Aaxol Material stop adjustable with detent points and display on the display Program control for automatic adjustment of the punch height, the angle, and the punching height Up to 6 programs can be stored Hydropneumatic material feed via 2-hand operation Pneumatic material clamps coolant lubrication

Year of construction: 1970, condition: good (used), machine/vehicle number: 1258, disk of circular saw-Ø: 315 mm cutting area at 90° round: 90 mm Gbsdpjh I Dvnsfx Aaxel cutting area at 90° square: 80 x 80 mm cutting speeds: 12,5 - 25 m/min forward feed speeds: hydropneumat. stufenl. regelbar cutting length: 5 - 1580 mm saw drive: 380 V, 1,8/2,5 kW space needed: 2300 x 1000 x 2800 mm weight: 940 kg

Year of construction: 1967, condition: used, machine/vehicle number: 9317, disk of circular saw-Ø: 275 mm cutting area at 90°: 120 x 75 mm cutting area at 45°: 90 x 65 mm rotations of disk: 2000 rpm engine: 380 V, 1,1 kW space needed: 700 x 900 x 1000 mm Gbsdpsb N Eicjfx Aaxol

Year of construction: 1991, condition: good (used), machine/vehicle number: 900 1241, disk of circular saw-Ø: 275 mm cutting area at 90° round: 90 mm cutting area at 90° square: 75 x 75 mm cutting area in mitre at 45° square: 75 x 75 mm disk rotations: 40/80 upm Gjdpfx Aaom Twgwjxsbl engine: 380 V, 1/1/2 kW space needed: 700 x 600 x 1580 mm weight: ca. 180 kg