Used Carpet Paternoster for sale (489)

Condition: new, Year of construction: 2026, Equipment: safety light barrier, 1A Gmatick Storage Paternoster (roll rack) Bdjdpfoff Huwsx Aa Ioh The foil storage Paternoster foils is suitable to use for the storage of all 3D-films, it is used as a high storage at the membrane press or as a space-saving storage solution for the 3D foils. With our Paternoster you can storage on very small area approximately 2, 4m x 1, 2m a lot of film rolls (up to 32 rolls of a Ø 300 mm). The required film is thus immediately available at the push of button. Our Paternoster are available from 2.8 m up to 6, 0 m as standard Paternoster. Also special solutions are offered by us, please contact us, we will then find the right solution for your storage. As additional equipment we offer center sleeves, a manual cutting station or the full automatic cutting device and we have also ionization solutions available at Gmatick. • Storage rods ø 42.4 mm • Sleeves inside Ø max. 82 mm,. • Load chain as a hollow pin chain with a breaking load of 100 kN, • Chain pitch is 50 mm hole to hole and this is the raster for the positioning of the mounting foil bars. • Control with a key switch (dead man) for on / off • Rotational speed of the chain is approx. 5.5 m / min • Voltage 400 V, 3N; 50/60 Hz or as USA Version 480V 60Hz • Mains cable with CEKON plug 16A fuse protection (by the customer) 10A slow blow • ground load data at least 2, 2 kg / cm² • Side covering over the entire height of the Paternoster, guards from 2, 2 m above floor to top edge of the Paternoster. • Requirement for the installation of the Paternoster is a viable, flat and solid floor, • Floating floors you can’t install a Paternoster. It is forbidden

Condition: used, Year of construction: 1991, Number of shelves: 10, three-phase mains connection: 380V, N/PE, frequency: 50Hz, duty cycle: 40%, supply fuse rating: 6A, rated power consumption: 1500W, an on-site inspection is possible. Bdsdpfxezzqcis Aa Ieh

Condition: good (used), Maximum part length: 3 m Maximum package depth: 1 m Bdjdpfx Aozzq S Rea Ijh Maximum package height: 1.7 m Equipped with a Siemens control system

Condition: used, Year of construction: 2002, functionality: unexamined, machine/vehicle number: 128.752, total height: 8,000 mm, total width: 2,500 mm, total length: 2,900 mm, load capacity per storage section: 250 kg, type of input current: three-phase, input voltage: 400 V, input frequency: 50 Hz, input current: 9 A, We are offering this used Haenel Lean-Lift storage lift, manufactured in 2002. Type: Lean-Lift Year of manufacture: 2002 Serial number: 128.752 Operating mode: 100% continuous duty Phases: 3 Frequency: 50 Hz Voltage: 400 V Current: 9.6 A Power: 4.0 kW Vertical motor type: S670V100M4/BMG/TH Vertical idle speed: 1380 rpm Horizontal motor type: S320T80K4BMG/TH Horizontal idle speed: 1360 rpm Switch number: S502002 Max. table load: 250 kg Max. total load: 20000 (2 × 10000) kg The price is for self-dismantling and pick-up. Bdjdpfx Aozzgy Rsa Ish Dismantling and loading by a specialist company: €5600 net plus VAT. Transport can be arranged for an additional fee. If you have any questions or require further information, please feel free to send us a message or call us.

Condition: good (used), Year of construction: 2014, Manufacturer: Hänel Type: Lean Lift Year of manufacture 2014 Device dimensions: H 6302mm approx. W 2805 mm D 2810 mm Shelf 40 pieces up to 400kg per container H 57mm Bedpfx Aaovt Euzj Isdh D 825mm W 2460mm Total load: 40,000kg (2×20,000kg)

Condition: like new (used), Year of construction: 2019, We now have two Kardex Megamat RS 650 units available. Both machines were manufactured in 2019 and put into operation in 2020. They have been serviced annually by the manufacturer and are in very good condition. The Kardex Megamat RS 650 is a powerful vertical carousel designed for storing and handling heavy goods. Each carrier (base shelf) can hold up to 650 kg, making the machines suitable for storing large and heavy items. The two machines have a total of 34 carriers (base shelves) and 43 trays: 28 carriers without intermediate shelves, with a height of 348 mm 3 carriers with two intermediate shelves, providing a total of 9 trays with a clear height of 115 mm 3 carriers with one intermediate shelf, providing a total of 6 trays with a clear height of 170 mm The machines are also equipped with a Matrix display in the access opening. This LED display shows information such as the picking location, quantity, and other useful details. The Matrix display helps reduce search time and the risk of picking errors, making the picking process faster and easier. To utilize the full functionality of the Matrix display, the machines need to be connected to an ERP or Warehouse Management System (WMS). Technical Information: Model year: 2019 Model: MEG RS 650.1.3250.6.406.34 Machine height: 7,835 mm Machine width: 3,975 mm Machine depth: 1,711 mm Number of carriers: 34 Number of shelves: 9 Maximum carrier height: 348 Carrier width: 3250 Bdodpoz Aiwbsfx Aa Ish Carrier depth: 628 Electronics: 3/N/PE 400V, 20A

Condition: used, Year of construction: 1989, Gewinner Euromat Type: Gewinner Euromat Machine No.: 120-50508-18 Year: 1989 Machine height: approx. 5600 mm Machine width: approx. 3300 mm Machine depth: approx. 1450 mm + 330 mm table top Number of trays: 18 Tray width: approx. 2450 mm Bedsya Dklepfx Aa Ijdh Tray depth: approx. 520 mm Tray height: approx. 500 mm Compartment load capacity: 510 kg Total load capacity: 9100 kg Colour: Beige front / corners blue

Condition: ready for operation (used), Year of construction: 1991, A roll paternoster ESKA storage and loading system is available. Roll width: 1600mm, max. load capacity: 2800kg, total height: 4300mm. Documentation available. An on-site inspection is possible. Bdodsw I E Dcjpfx Aa Ieh

Year of construction: 2012, condition: good (used), Type: IND-PA Device No.: 0/1220744/1 Year of manufacture: 2012 Device height: approx. 5600 mm Device width: approx. 2870 mm Device depth: approx. 4000 mm Bdsdpfxjhyhlgs Aa Ijh Number of rollers: 45 Roller width: approx. 2370 mm Shelf load capacity: 200 kg Total load capacity: 9000 kg Color: beige

Condition: used, functionality: fully functional, total length: 1,500 mm, load capacity: 16,000 kg, Tragedorn Bdjdpfsz Evv Tjx Aa Ijh Condition: Ready for use and fully functional Technical condition: very good Description: Length: 1500 mm, diameter: 350 mm

Condition: like new (used), Year of construction: 2020, functionality: fully functional, machine/vehicle number: 106000162, total height: 4,400 mm, total width: 2,350 mm, total length: 10,470 mm, construction height: 4,400 mm, construction width: 2,350 mm, type of input current: three-phase, input voltage: 400 V, empty load weight: 5,000 kg, input frequency: 50 Hz, input current: 28 A, Equipment: documentation/manual, Kardex Remstar LR-35 vertical buffer module (Compact Buffer / Miniload-in-a-Box) with integrated SmartLOG pick-to-light system. Year 2020. Like new, never used. Zero operating hours. The system was fully commissioned by the installer, but the company ceased operations before it entered service, so the machine has been idle in like-new condition since installation. Technical data (nameplate): Type: LR-35-20X400X600X4400 Serial number: 106000162 Year: 2020 Manufacturer: Kardex Produktion Deutschland GmbH, Neuburg plant Nominal voltage: 3/N/PE 400 V, 50/60 Hz Nominal power: 20.0 kVA / 28.8 A Max. load per bin: 35 kg Certification: CE, TUV SUD, GS Configuration (installer specification): Dimensions: 2,350 mm wide x 10,470 mm long x 4,400 mm high Storage: 2 aisles x 20 portals x 17 levels 675 bins of 400 x 600 x 122 mm Useful volume: 19.76 m3 Throughput: 110 to 130 bins per hour Bodpfxeztzqbe Aa Iedh At 4.4 m high, the machine fits a standard warehouse, unlike taller LR units that require a very high building. Location: San Sebastian, Spain. Sold ex location, buyer arranges dismantling and transport. Full documentation available (invoice, CE declaration, manuals, installer technical specification, and layout drawing). A second identical unit (2019, low use) is also available. Price negotiable. Serious inquiries welcome.

Year of construction: 2017, condition: good (used), functionality: fully functional, For sale is a carousel oven (Paternosterofen) from the brand Eliog, model PNO 80. This oven is a custom-built solution. Designed for warming components, equipped with a carousel handling system and control cabinet. Also suitable for drying or dehydrating food and cannabis. The system was installed in 2017 and has only been used occasionally since around 2022. The plant has already been dismantled. Technical specifications: Year of manufacture: 2017 Max. component support area: 65 mm Nominal temperature: 70°C Operating temperature: 70–75°C (At 75°C the utilisation area safety limiter shuts off!) Set conveyor time: approx. 240 min Max. airflow speed: approx. 4 m/s Heating capacity: 72 kW Nominal voltage: 3*400 V, 50 Hz Fresh air supply: Ambient air at the oven Exhaust air: max. 850 m³/h Usable chamber dimensions: 4780*2200*2250 mm Workpiece carriers: 56 pcs. (oven capacity) Max. workpiece weight: 0.3 kg Transport height above floor: 400 mm Heating: 3 kW / heater element, 6 heater elements per control zone-4 (total 72 kW output) Overall dimensions: approx. 4,425*5,425*4,980 mm Space requirement: 5012.4*3919.5*5000 mm Oven weight: approx. 7,500 kg Control cabinet: approx. 450 kg (Images have been modified due to copyright reasons) Transport and loading can be organised across Europe for an additional fee upon request. Bsdpsup R U Ujfx Aa Iodh Prices are plus VAT. Inspections are possible by appointment. Please contact us – our team will be glad to assist you. Part exchange or trade-in possible! Machine Purchase & Sale BUYING / SELLING PRODUCTION MACHINERY & METALWORKING MACHINES AND MORE. Are you looking for a high-quality yet affordable metalworking machine for your production? Or are you interested in selling yours? For further information or to get in touch, please visit our website.

Condition: used, Year of construction: 1998, Hänel Type: Rotomat 950 Device No.: 120.657*1 Year of manufacture: 1998 Device height: approx. 3800 mm Device width: approx. 3140 mm Bodpfx Aaey D S Hwe Iodh Device depth: approx. 1250 mm + 330 mm tabletop Number of trays: 18 Tray width: approx. 2880 mm Tray depth: approx. 400 mm Tray height: approx. 310 mm Shelf load capacity: 300 kg Total load capacity: 5400 kg Colour: Beige front / corners grey

Condition: like new (used), Year of construction: 2019, operating hours: 1,000 h, functionality: fully functional, machine/vehicle number: 106000127, total height: 4,400 mm, total width: 2,350 mm, total length: 10,470 mm, construction height: 4,400 mm, construction width: 2,350 mm, type of input current: three-phase, input voltage: 400 V, empty load weight: 5,000 kg, input frequency: 50 Hz, input current: 29 A, Equipment: documentation/manual, Kardex Remstar LR-35 vertical buffer module (Compact Buffer / Miniload-in-a-Box) with integrated SmartLOG pick-to-light system. Year 2019. Used, good condition, approximately 7 months in service. Bsdpfx Aaezu Ttkj Isdh This was the original unit at the site. It operated for about 7 months before the company ceased operations, so it is in very good working order with low operating hours. Fully commissioned and functional. Technical data (nameplate): Type: LR-35-20X400X600X4400 Serial number: 106000127 Year: 2019 Manufacturer: Kardex Produktion Deutschland GmbH, Neuburg plant Nominal voltage: 3/N/PE 400 V, 50/60 Hz Nominal power: 20.0 kVA / 28.8 A Max. load per bin: 35 kg Certification: CE, TUV SUD, GS Configuration: Dimensions: 2,350 mm wide x 10,470 mm long x 4,400 mm high Storage: 2 aisles x 20 portals x 17 levels 675 bins of 400 x 600 x 122 mm Useful volume: 19.76 m3 Throughput: 110 to 130 bins per hour At 4.4 m high, the machine fits a standard warehouse, unlike taller LR units that require a very high building. Location: San Sebastian, Spain. Sold ex location, buyer arranges dismantling and transport. Full documentation available (invoice, CE declaration, manuals, technical specification, and layout drawing). A second identical unit (2020, never used) is also available. Price negotiable. Serious inquiries welcome.

Condition: used, Year of construction: 2011, total height: 11,550 mm, Automated warehouse optimization storage system KARDEX Shuttle XP500 System Type: SHUTTLE-XP-500-3050x864 Control: C3000, with OP3000 OPGraphic color display Serial No.: 11007548/001 Year of construction: 2011 Load per tray: Medium: 205 kg & Heavy: 265 kg (evenly distributed) Tray dimension: 3050 x 864 mm Number of trays: 32 pieces (more trays available upon request) Dimensions Shuttle W x D x H: 3380 x 3074 x 11,550 mm (height of Kardex is adjustable to available height) Power: 3/N/PE400 V, 17 A, 50/60 Hz, 8.6 kVA This offer is valid subject to the system being unsold. Technical details per Shuttle: - Maximum total capacity of the KARDEX Shuttle XP: 2 x 33,500 kg Bodpfxezuvtae Aa Ijdh - Maximum tray capacity: 32 trays, Medium: 205 kg & Heavy: 265 kg each, evenly distributed; more trays can be ordered. - Tray dimensions: 3050 x 864 mm - Machine dimensions: Width x Depth x Height: 3380 x 3074 x 11,550 mm - Footprint of the system approx.: 10.39 m2 - Capacity with 32 trays: approx. 84 m2, each tray approx. 2.64 m2 - Electronic volume measuring system in 25 mm grid - An access opening with sliding doors to protect people and stored goods - Control C3000, with OP3000 OPGraphic color display - LED anti-glare lighting above access point - Use of toothed belt for minimum noise - Use of toothed belt for fastest order picking - Including light pointer (requires software to function; software is not included with the machine) Price: on request, via email only Price: excl. VAT, including transport, installation and warranty Delivery time: in stock Machinehandel De Leeuw BV is one of the few companies in Europe that deals in and has in stock primarily used Kardex Remstar VLM automatic lift & rotating storage systems. See our website for current stock. We install and/or dismantle these systems in a safe manner with VCA-certified technicians, and we have been doing so for over 33 years. We also dismantle other brands such as: Hänel, Electrolux, Bertello, Megamat, Lista, Denocard. Machinehandel De Leeuw BV Oordeelsestraat 7-B 5111 PA Baarle-Nassau The Netherlands

Condition: excellent (used), Year of construction: 1994, functionality: fully functional, Very well-maintained and robust Heesemann MFA 8 wide belt sanding machine for professional use. The machine is particularly suitable for surface, fine, and finish sanding and features electronic control as well as cross and longitudinal sanding units. The machine is in very good used condition. Technical data: Manufacturer: Heesemann Type: MFA 8 Year of manufacture: 1994 Machine number: 9411252 Working width: approx. 1,300 mm Cross belt: 4,800 × 150 mm Pressure pad belt: 4,450 × 140 mm Longitudinal sanding belt: 2,100 × 1,350 mm Voltage: 400 V Frequency: 50 Hz Total connected power: approx. 50 kW Rated current: 100 A Sanding belt dimensions: 4,800 × 150 mm Pressure pad belt: 4,450 × 140 mm Constant working height Electronic control Cross belt unit Longitudinal sanding unit Brush units Suitable for finish, fine and surface sanding Weight: approx. 4,000 kg Equipment: Electronic control panel Pneumatic unit adjustment Feed carpet Dust extraction connections CE marking Bdjdpozxyfhefx Aa Ioh Transport possible for an extra charge! The machine is currently still at the customer's site but would be immediately available! The machine will be inspected before sale. For used machines manufactured in 2009 or earlier, the warranty is excluded when sold to commercial customers. Technical data and equipment may vary. Errors, prior sale, and changes are subject to change. All information without guarantee.

Condition: used, Year of construction: 2014, total height: 6,550 mm, Automated warehouse optimization storage system KARDEX Shuttle XP500 System Type: SHUTTLE-XP-500-3050x864 Control: Logicontrol, with colour Touchscreen display Bedpfx Aaezuvt Tj Isdh Serial No.: 14001667/002 Year of construction: 2014 Load per tray: Medium X Typ2: 460 kg (evenly distributed) Tray dimension: 3050 x 864 mm Number of trays: 32 pieces (more trays available upon request) Dimensions Shuttle W x D x H: 3380 x 3074 x 6550 mm (Kardex height is adjustable to available height) Power: 3/N/PE400 V, 17 A, 50/60 HZ, 8.6 kVA This offer is valid as long as the system is unsold. Technical details per Shuttle: - Maximum total capacity of the KARDEX Shuttle XP: 2 x 33,500 kg - Maximum tray capacity: 32 trays Medium X Typ2: 460 kg each, evenly distributed, more trays can be ordered. - Tray dimensions: 3050 x 864 mm - Machine dimensions: Width x Depth x Height: 3380 x 3074 x 6550 mm - Footprint of the system approx.: 10.39 m2 - Capacity with 32 trays: approx. 84 m2, each tray is approx. 2.64 m2 - Electronic volume measuring system in 25 mm grid - An access opening with sliding doors to protect people and stored goods - Logicontrol, with colour Touchscreen display - LED anti-glare lighting above access point - Use of toothed belt for minimum noise - Use of toothed belt for fastest order picking Price: upon request, only via email Price: excl. VAT, including transport, installation, and warranty Delivery time: in stock Machinehandel De Leeuw BV is one of the few companies in Europe that trades in and stocks mainly used Kardex Remstar VLM automatic lift and rotating warehouse systems. Please visit our website for the current stock. We install and/or dismantle these systems in a safe manner with VCA-certified technicians, and we have been doing so for over 33 years. We also dismantle other brands such as: Hänel, Electrolux, Bertello, Megamat, Lista, Denocard. Machinehandel De Leeuw BV Oordeelsestraat 7-B 5111 PA Baarle-Nassau The Netherlands

Condition: excellent (used), Year of construction: 2023, functionality: fully functional, power: 7.5 kW (10.20 HP), planing width: 625 mm, tool diameter: 125 mm, number of blades: 4, rotational speed (min.): 5,000 rpm, overall weight: 1,000 kg, 4-knife TERSA cutter head for planer Motor power 7.5 kW Positioning control for the thickness table Segmented infeed roller Segmented pressure bar Feed speeds of 7 + 14 m/min Table extension Planing width 625 mm, chip removal up to 8 mm, planing height 3.5-305 mm Thickness table mounted on four support spindles and with 4-point guidance. Heavily ribbed cast iron table, finely planed Modern control panel ergonomically positioned. Electric thickness table adjustment with LED display. Buttons for adjusting in rapid or slow mode, Adjustment accurate to 1/10 mm; integrated operating hour counter. Electronic starting and braking system. Electronic, wear-free brake for safe stopping of the cutter head. Infeed roller in rubber and two rubber outfeed rollers (high quality, low wear) Bdodpfx Asz Dkftoa Ioh Segmented pressure bar, rotary knob with scale, for adjusting the pressure (preload) of the outfeed pressure bar Two feed speeds 7 + 14 m/min; electrically switchable, also during planing Thickness hood with carpet support, can be used as a storage area for wood. Dust extraction port Ø 160 mm, to the left (can also be on the right – can be easily converted on site) Air velocity 22 m/s Integrated tool storage compartment for operating tools and planing knives Electrical equipment according to VDE/EN 60204 with main switch, emergency stop button and 2nd emergency stop button on the discharge side, winding protection, undervoltage protection, contact for controlling the dust extraction, accessories: 1 set of knives installed, operating tools, grease gun, operating manual Weight: approx. 1000 kg CE-compliant, BG-Holzstaubgeprüft No. HM 23001 Workplace-related emission values dB(A) according to DIN 45635 Part 1650 Idle noise approx. 69 dB(A), operating noise approx. 79 dB(A) Workplace-related dust emission value: 0.44 mg/m³

Year of construction: 2003, condition: good (used), Type: TLI 4500/2044 Device No.: 03502 Year of Manufacture: 2003 Bodpjhyhlkofx Aa Ijdh Device Height: approx. 4500 mm Device Width: approx. 2000 mm Device Depth: approx. 7010 mm Number of Rollers: 44 Roller Width: approx. 1680 mm Shelf Load: 150 kg Total Load: 7000 kg Superstructure: see photo, 3000 mm Color: beige

Condition: used, Year of construction: 2006, functionality: unexamined, machine/vehicle number: 06000511/001, These two vertical lift storage systems, model Kardex Shuttle XP 250-2150x864, version H/N55/N22D11B/N75D15/20, manufactured in 2006, with a permissible total load capacity of 2 x 32,900 kg and a permissible shelf load of 245 kg, will be auctioned off in our complete online auction "Kardex Vertical Lift Storage". Further details: Description Year of manufacture: 2006 Used Technical data Manufacturer: Kardex Produktion Deutschland GmbH Model: Shuttle XP 250 Type: Shuttle-XP-250-2150x864 Year of manufacture: 2006 System 1 • Serial number: 06000524/001 • Permissible shelf load: 245 kg per shelf Bodpfx Ajz Eqatsa Isdh • Permissible total load capacity: 2 × 33,250 kg System 2 • Serial number: 06000511/001 • Permissible shelf load: 245 kg per shelf • Permissible total load capacity: 2 × 32,900 kg Electrical data (per system) • Mains connection: 3/N/PE 400 V • Frequency: 50/60 Hz • Rated current: 17.0 A • Connection power: 8.6 kVA • CE marking available These systems are ideal for space-saving, safe, and efficient storage of tools, spare parts, small parts, as well as production and operating materials. The storage systems operate according to the proven "goods-to-man" principle. The requested shelves are automatically transported to the retrieval opening, which reduces search and travel distances and significantly increases efficiency in storage and production operations. The vertical design makes optimal use of the available hall height and achieves a high storage capacity in a small footprint. Condition An on-site inspection is recommended. Dismantling, loading, transport, and recommissioning are the responsibility of the buyer or will be arranged separately. As pictured Without any other items or components shown in the images Content, condition, and completeness are unverified Functionality is unverified

Condition: used, Year of construction: 2018, total height: 8,950 mm, Automated warehouse optimization storage system KARDEX Shuttle XP250 System Type: SHUTTLE-XP-250-3050x864 Control: Logicontrol, with color touchscreen display Serial No.: 18001465/001 Year of construction: 2018 Load per tray: Medium: 205 kg (evenly distributed) Tray dimension: 3050 x 864 mm Number of trays: 32 pieces (more trays available upon request) Dimensions Shuttle W x D x H: 3380 x 3074 x 8950 mm (height of Kardex is adjustable to available height) Power: 3/N/PE400 V, 17 A, 50/60 Hz, 8.6 kVA This offer is valid as long as the system is unsold. Technical details per Shuttle: - Maximum tray capacity: 32 trays, Medium: 205 kg each, evenly distributed; more trays can be ordered. - Tray dimensions: 3050 x 864 mm - Machine dimensions: Width x Depth x Height: 3380 x 3074 x 8950 mm - Footprint of the system approx: 10.39 m2 - Capacity with 32 trays: approx. 84 m2; each tray is approx. 2.64 m2 - Electronic volume measuring system with 25 mm grid - An access opening with sliding doors to protect people and stored goods - Logicontrol, with color touchscreen display Bsdpszuvq Esfx Aa Iedh - LED anti-glare lighting above access point - Use of toothed belt for minimum noise - Use of toothed belt for fastest order picking Price: upon request, via email only Price: excl. VAT, including transport, installation, and warranty Delivery time: in stock Machinehandel De Leeuw BV is one of the few companies in Europe that deals with and has in stock primarily used Kardex Remstar VLM automatic lift & rotating warehouse systems. See our website for current stock. We safely install and/or dismantle these systems with VCA-certified technicians, and we have been doing so for over 33 years. We also dismantle other brands such as: Hänel, Electrolux, Bertello, Megamat, Lista, Denocard Machinehandel De Leeuw BV Oordeelsestraat 7-B 5111 PA Baarle-Nassau The Netherlands

Year of construction: 2007, condition: ready for operation (used), A vertical carousel storage system (office lift) Hänel with front access is available. Trays: 18, tray arrangement: 4-lane, max. stack load per tray: 132kg, machine dimensions X/Y/Z: approx. 3300mm/1000mm/2850mm, weight: approx. 3000kg, control: MP0A. Documentation available. An on-site inspection is possible. Bdjdpfx Ajyiflgsa Ijh

Condition: excellent (used), Year of construction: 2008, operating hours: 282 h, Calibrating and finishing machine, wide belt sanding machine with electronic segmented sanding pad and finishing sander Ideal sanding machine for interior design companies, also suitable for intermediate sanding of lacquered surfaces. Edge banding machine with combination unit and electronic articulated pressure bar, edge segments can be switched on and off. Segment width of the pressure bar: 35 mm Contact roller can be pneumatically adjusted, low wear due to ribbed steel roller Grain size compensation Drive motor 7.5 kW with automatic motor brake, stepless belt speed controlled by frequency inverter from 2 - 18 m/s Belt feed speed can be steplessly adjusted via frequency inverter from 2.5 - 13 m/min Pneumatic workpiece-controlled belt blowing device Cleaning brush at the discharge end Constant working height of 900 mm by adjusting the upper part of the machine, thus can also be integrated into sanding lines. Bdedpezqvmrefx Aa Ish Feed belt still has good grip and is in very good condition. Maximum sanding width approx. 1340 mm Workpiece height approx. 3 to 150 mm Common sanding belt dimension: 1360 x 1900 mm 3 rubberized pressure rollers Infeed roller table and foldable discharge table Preparation for vacuum blower. The carpet is perforated and connectors for an optional blower are available. Alternatively, the carpet can also be connected to the extraction system. Extraction connection: 1 x 200 mm, 1 x 140 mm, and 2 x 100 mm Terminal control with 50 programmable sanding programs for automated machine control. Parameters: Belt speed, feed speed, workpiece height, pressure bar setting points at the front and rear, as well as edge segments, belt blowing nozzle, optional vacuum blower, pneumatic adjustment of the calibrating roller. CE marking Operating manual Without the illustrated connection cable Original paint, only retouched in some areas Approx. 282 operating hours, i.e. approx. 20 minutes per week. Dimensions approx. 1800 (with table 2600) x 2050 x 2150 mm (L x W x H). Weight approx. 2400 kg. The machine can be demonstrated on site after prior arrangement. We only offer machines that are ready for demonstration in our warehouse; see "other offers from this provider".

Condition: like new (used), Year of construction: 2023, We currently have three SSI Schäfer Logimat SLL 3625x815 Vertical Lift Modules for sale. All three machines were manufactured in 2023 and are in excellent condition. They have seen very little use and have been serviced annually by the manufacturer since installation. Each machine has a height of 11,550 mm. The height can be adjusted and lowered during installation to fit the building’s ceiling height. Each machine has: 62 trays Tray width: 3,625 mm Tray depth: 815 mm Total storage area: approximately 183.1 m² Maximum tray load: 450 kg Together, the three machines provide approximately 549.3 m² of storage space. The machines are equipped with several optional features: LogiPointer LogiTilt LogiBar LogiDriver LogiWork These features help make the picking process faster, easier, and more ergonomic. They also help reduce picking errors and improve the operator’s working position. Please note that these optional features require integration with a WMS or business system. Specifications: Model year: 2023 Model: SSI Schäfer Logimat SLL 3625x815 Machine height: 11,550 mm Machine width: 4,135 mm Bdsdpfxezzwure Aa Ieh Machine depth: 3,092 mm Tray width: 3,625 mm Tray depth: 815 mm Number of trays: Approx. 60 / machine Maximum weight per tray: 450 kg Electronics: 3/N/PE 230/400V

Condition: good (used), Year of construction: 2011, We now have two Kardex Shuttle XP 500 units, 3050 x 813 mm, from 2011 available for sale. The machines are in good condition and have been regularly serviced since installation. The Kardex Shuttle XP 500 is a reliable and proven storage system used by thousands of companies worldwide. Each tray is 3,050 mm wide and 813 mm deep, providing 2.5 m² of storage space. The system offers a total of 112.5 m² of storage space while using only 9.87 m² of floor space. Technical Information: Model year: 2011 Model: SHUTTLE-XP-500-3050x813 Machine height: 7,500 mm Bdodpfx Aaozybfxo Ijh Machine width: 3,380 mm Machine depth: 2,921 mm Tray width: 3,050 mm Tray depth: 813 mm Number of trays: Approx. 45 / machine Maximum weight per tray: 210 kg Electronics: 3/N/PE 230/400V 17A