Used Barbed Wire for sale (2,980)

Condition: used, Year of construction: 2008, Versch GL 18 Closure for medicinal vial GL18 Rjdpfx Aodqbzqskiech Injection mold with 10-cavity

Condition: used, CTS Type: TSS-70/130 Water-cooled cooling unit For sale is a high-quality temperature shock test chamber from CTS (Clima Temperatur Systeme), model TSS-70/130. The device is used for performing temperature shock tests and is typically used in industry, research, and quality assurance. Application areas: Material tests Aging tests Electronics and component tests Temperature shock and cyclic temperature tests Technical data: Type: TSS-70/130 Test volume: 130 liters Temperature range: Hot chamber: +50°C to +200°C Cold chamber: -80°C to +100°C Heating rate: approx. 6 K/min from room temperature to +180°C Cooling rate: approx. 4 K/min from room temperature to -60°C Temperature deviation: ±1 K in time ±2 K spatially Temperature change rate: max. 100 K/min on average for shock test tests without heat input Temperature adjustment rate: ≤ 15 min in the range of -65°C to +200°C with 10 kg of ICs Cycle time: < 10 seconds Electrical data: Connection: 400 V, 3/N, 50 Hz Rated power: approx. 17.2 kW Rated current: approx. 29 A On-site protection: 32 A slow-blow fuse Connection: Cekon 32 Refrigeration system: Refrigerant: R404A / R23 water-cooled, low-noise, fully hermetic Equipment / Features: CTS control panel Microprocessor-controlled control and monitoring system Program operation up to 100 test programs possible digital setpoint and actual value display RS232 interface 2 free switching channels for on-site control of the test specimen Fault message on potential-free contact Load up to 30 V DC, 2 A EMC tested Rjdpfx Akoy Hkd Hoioch Technical design: Hot and cold chamber Mobile frame with lifting spindle drive Test chamber / mobile frame made of stainless steel, material no. 1.4301 Insert basket made of stainless steel wire Pipe passage NW 50 with sealing plug Compressed air connection 1/4" AG Condensate drain non-pressurized R 1/2" internal thread Safety door lock lockable door with window Dimensions according to installation diagram: External dimensions approx.: 2335 x 940 x 1820 mm Loading dimension approx.: 1990 x 940 x 1652 mm Test chamber dimensions: height approx. 410 mm Width approx. 480 mm, depth approx. 660 mm Window: 300 x 300 mm Other data: Protection class: IP 22 Sound pressure level: < 60 dB(A) Weight: approx. 950 kg Average consumption during test cycle: approx. 8 kWh For your safety as a buyer, the following information: The following points are carried out on our offered chambers in advance: 1. Functional check and replacement of necessary components 2. If necessary, refill with legally compliant refrigerant 3. Leak test with certificate 4. After successful inspection, the chambers are subjected to a documented test run. Condition: used Scope of delivery: see pictures (Changes and errors in technical data are subject to change!) We will gladly answer any further questions you may have by telephone.

Condition: like new (used), Year of construction: 2004, Retrofitted: 2026 Numerical control: HEIDENHAIN TNC-i530 Rceds Admb Rjpfx Akish Technical features Dimensions Table dimensions: 2000 x 900 mmNumber of T slots: 5T slots dimensions: 22 mm Traverses of axis X axis traverse: 2000 mmY axis traverse: 1000 mmZ axis traverse: 1000 mm Milling head Head type: Manual milling head (U22)Tool clamping system: HydraulicTaper nose: ISO 50 (DIN 69871) / Pull stud: DIN 69872Speed range: 3000 rpmSpindle power: 22 kW Feedrates Rapid feedrate (X / Y,Z): 20000 / 12000 mm/min Weight and dimensions Maximum weight on table: 3500 kgMachine weight approximate: 14000 kgMachine dimensions approximate: 6367 x 5070 x 2803 mm Accessories Guarding: 2 sliding doors and new perimetral wire-mesh fenceTool pedal: new foot clamping tool pedalElectronic handwheel: New HR-510Coolant: external Sale conditions Warranty: 6 months mechanical partsPrice and sale conditions: On request View all technical features

Condition: used, Year of construction: 1994, machine/vehicle number: GA24, Used ROBINO & GALANDRINO Wirehooder record 10-2Technical Specifications & Performance DataThis Automatic Wirehooder is a compact, high-performance wirehood applicator designed for sparkling wine and premium beverage closures. Built for reliable operation on glass bottles, it delivers precise wirehood positioning and twisting for consistent, secure muselet application at industrial speeds.Machine type: Automatic Wirehooder (wirehood/muselet applicator)Model: Record 10/2Year of manufacture: 1994Refurbishment: Overhauled in 2017Production speed: 10,000 bphContainer material: Glass bottlesInfeed direction: ClockwiseWirehood magazine: High-capacity, long-autonomy designSupported wirehood styles: Collio, Collio light, Collina, Lia, Sile, Extra L, Valdobbiadene, Elegance, Artù, Piave, Monterossa, Cru, Magnum CollioAdvanced Automation & Control SystemsEngineered for stable, repeatable operation, this wirehooder features automated feeding and consistent torque application to protect cork integrity while ensuring firm cage tightening. The long-autonomy magazine reduces manual replenishment for improved uptime on a used bottling line or integrated second hand packaging cell. Operator-friendly controls support quick setup and process monitoring for efficient beverage production.Automated wirehood feeding with alignment and controlled twist applicationHigh-capacity magazine to extend runtime between reloadsOperator controls for speed and format parametersStandard safety interlocks and emergency stop circuitsProduction Line Integration CapabilitiesThis wirehooder integrates seamlessly downstream of a corking machine on glass bottling lines. It can function as a standalone module or as part of a synchronized industrial packaging line with upstream and downstream conveyors, accumulation, and inspection systems.Inline or standalone operation with conveyor interfacesDesigned for glass bottle handling in sparkling applicationsFormat changeover kits support various wirehood styles listed aboveSuitable for integration into complete bottling and beverage production linesMachine Condition & Maintenance HistoryThe unit was manufactured in 1994 and underwent a refurbishment in 2017, providing renewed reliability of key components and alignment systems. It is presented in good working order and ready for operation, ideal for facilities seeking robust second hand bottling equipment with proven performance.Operational Performance & VersatilityOptimized for sparkling closures, the machine handles a broad range of wirehood designs without compromising on application quality. Its high-speed performance supports commercial throughputs, while the magazine capacity helps maintain continuous operation and minimize changeover interruptions.Consistent cage placement and twist control for secure closureWide compatibility with premium wirehood styles for different brand aestheti... Rjdpfx Akszmpzusioch

Condition: used, Year of construction: 2011, overall weight: 1,622 kg, load capacity: 240 kg, arm reach: 2,700 mm, This is a used, tested welding robot system comprising a KUKA KR 240-2 2000 and a KRC2 ed05 controller from 2011, combined with a welding unit from SKS Welding Systems. The system is designed for industrial welding and automation applications and is typically used for arc welding, heavy-duty assembly operations, and combined handling/welding tasks. The robot has a payload capacity of 240 kg and a reach of 2700 mm, making it suitable for large-scale workpieces. The system is equipped with an SKS LSQ 4 welding power source featuring wire feeder, welding torch, and a complete hose package. Redpsy Nfl Dofx Akioch

Condition: used, Year of construction: 1994, machine/vehicle number: GA23, Used ROBINO & GALANDRINO wirehooder 6000 BPHTechnical Specifications & Performance DataThis automatic wirehooder is engineered for reliable wire cage application on bottles, ensuring consistent tightening and alignment at production speeds suitable for medium-scale beverage production. Manufactured by Robino & Galandrino, the REKORD 10/2 configuration combines a rotary handling system with a long-duration magazine and ground-level loading to minimize downtime during continuous operation. This second hand unit is a strong addition to any used bottling line focused on premium products and industrial packaging efficiency.Manufacturer: Robino & GalandrinoModel: REKORD 10/2Year: 1994Machine type: Automatic wirehooder (wire cage applicator)Production speed: up to 6,000 bphConfiguration: 10 platesWirehood application: Muselet/wire cage applicationMagazine: Long-duration, high-capacityLoading: Ground-level cage loading for uninterrupted replenishmentBottle format compatibility: 1.5LAdvanced Automation & Control SystemsThe REKORD 10/2 platform is designed for dependable, automated performance with straightforward operator controls. The long-duration magazine and ground-level loading streamline replenishment, reducing stops and improving overall equipment effectiveness. Typical safety interlocks and guarding protect operators while allowing efficient access for adjustments and cleaning.Automated wire cage feed and applicationOperator-friendly controls and status indicationSafety guarding with interlocked access pointsQuick replenishment via ground-level magazine loadingProduction Line Integration CapabilitiesThis wirehooder integrates seamlessly into existing bottling equipment layouts, positioned downstream of corking and upstream of labeling or inspection as required. It supports inline operation with synchronized conveyors or can function as a standalone station with appropriate infeed and outfeed controls.Inline or standalone operation modesCompatible with upstream corkers and downstream labeling/inspectionFormat handling for 1.5L bottles; additional formats can be engineeredSuitable for integration within broader beverage production and industrial packaging linesMachine Condition & Maintenance HistoryThis second hand wirehooder is presented in working condition and ready for operation, providing a practical solution for producers seeking reliable bottling equipment with controlled capital investment.Operational status: Ready for operationPre-owned equipment from established engineeringOperational Performance & VersatilityThe REKORD 10/2 is built to deliver consistent wire cage application at up to 3,000 bottles per hour, supported by a 10-plate rotary handling system. The long-duration magazine and ground-level loading reduce changeover interruptions, supporting steady throughput in used bottlin... Rsdpfxjzcf I De Akisch

Condition: used, Year of construction: 2016, machine/vehicle number: GA22, Used R&B RECORD 12 wierhooder 12000 BPHTechnical Specifications & Performance DataThe Wirehooder RECORD 12 with double distributor is a high-efficiency machine engineered for securing wire cages on sparkling wine and similar glass bottles in industrial packaging environments. Designed for continuous operation in a used bottling line or as a standalone station, it delivers reliable, second hand performance for beverage production where consistency and throughput are essential.Model: RECORD 12Maximum speed: 12,000 bphRotation direction: Clockwise, left to rightYear of manufacture: 2016Double distributor: Supports 2-leg and 4-leg wire cagesDual magazines: Approx. 6,000 cages eachContainer handling: Designed for Glass bottle handlingAdvanced Automation & Control SystemsEngineered to reduce changeover time and operator intervention, this wirehooder integrates recipe-driven automation and precise handling features. Automated setup routines ensure consistent application quality while maintaining high throughput.Recipe-based automatic height adjustment: Quick format alignment via stored recipesUniversal infeed screw: Automatic setup with recipe for smooth bottle infeedSensors and interlocks: Cap detection (no cage application if no cap) and cage presence detection with machine stopProduction Line Integration CapabilitiesThe RECORD 12 integrates seamlessly into complete bottling and packaging lines for sparkling products. It can operate inline with upstream capping and downstream labeling or inspection systems, supporting a wide range of bottle diameters and heights typically used in sparkling wine packaging.Inline or standalone operation modesCompatible with upstream corking/capping stations and downstream labeling/inspectionEfficient material flow with left-to-right (clockwise) layoutMulti-format flexibility via recipe-based adjustmentsMachine Condition & Maintenance HistoryThis second hand wirehooder is presented in ready-for-operation condition, reflecting robust build quality and dependable performance for industrial packaging uses. It is suitable for rapid recommissioning within a used bottling line.Operational status: Ready for operationCommercially maintained features with functional automation and detection systemsOperational Performance & VersatilityOptimized for sparkling closures, the double distributor manages both 2-leg and 4-leg cages to cover diverse product SKUs. The dual high-capacity magazines sustain longer runs with fewer refills, supporting continuous beverage production.Wire cage formats: 2-leg and 4-legHigh-capacity dual magazines: Approx. 6,000 cages each for extended autonomyConsistent application quality at high speeds up to 12,000 bphIdeal for integration in sparkling wine bottling lines within industrial packaging operationsInstallation Requirements & Site P... Rcsdpfx Ajy Ef Tyekioh

Condition: excellent (used), Year of construction: 2020, Wireless Barcode Scanner - Reader Rsdpfx Aev Urv Ijkijch Manufacturer: Datalogic Model: Powerscan PM 9501 Type: 433MHzRB Weight: 445 g Accessories: Base Station Charger Wall Mount Replaceable Battery We have 45! FEATURES • Thanks to the powerful liquid lens, one model can read standard, wide, and high-density codes. • Fast omnidirectional reading • Intuitive aiming system • Soft white light illumination • Bluetooth 3.0 compatible: Class 1; Piconet with up to 7 scanners connected to the same base station • Ethernet connectivity (standard and industrial) • Lithium-ion battery replaceable in 3 seconds! • Datalogic Motionix™ motion sensor technology • Ergonomic shape enables hours of tireless data collection. • Image capture • Datalogic 3GL™ (3 green lights) technology and a loud beep for good read • Water and particle resistance: IP65 • Field-replaceable window and charging contacts • EASEOFCARE service plans offer a wide range of service options to protect your investment and maximize productivity and ROI

Condition: ready for operation (used), Year of construction: 2020, functionality: fully functional, TECHNICAL DETAILS Process Flow Continuous feeding of copper wire via an automatic double unwinder with flying splice capability Inductive wire preheating for moisture removal and improved adhesion Full insulation using a Rosendahl Automotive main extruder and a highly precise crosshead die Cooling and extraction Multi-stage, temperature-controlled telescopic water cooling trough for stress-free solidification of the plastic Synchronized precision caterpillar puller for consistent line speed Quality assurance and winding Laser diameter and ovality measurement Eccentricity measurement for monitoring consistent wall thickness High-voltage spark tester for real-time fault detection Uninterrupted winding onto process drums MACHINE DETAILS Machine type: High-speed full insulation line Design: Fully automatic system for thin-walled vehicle lines Year of manufacture: 2020 EQUIPMENT Automatic double unwinder with flying splice capability Inductive wire preheating Rcjdpfx Akoz N A Npeijh Rosendahl Automotive main extruder Highly precise crosshead die Temperature-controlled telescopic water cooling trough Precision caterpillar puller Laser diameter and ovality measurement Eccentricity measurement High-voltage spark tester Automatic double spool winder

Condition: ready for operation (used), Year of construction: 2022, operating hours: 1,472 h, travel distance X-axis: 762 mm, travel distance Y-axis: 508 mm, travel distance Z-axis: 508 mm, controller manufacturer: HAAS, controller model: NGC, table load: 680 kg, overall weight: 3,810 kg, spindle speed (max.): 12,000 rpm, spindle motor power: 22,400 W, tool weight: 5,000 g, number of axes: 3, This 3-axis HAAS VF-2SSYT was manufactured in 2022. It features an impressive X-axis travel of 762 mm, Y-axis travel of 508 mm, and Z-axis travel of 508 mm. The machine includes a robust table size of 914 x 457 mm and a maximum table load of 680 kg. If you are looking to get high-quality machining capabilities, consider the HAAS VF-2SSYT vertical machining centre we have for sale. Contact us for further details. • CNC control: Haas Next Generation Control (NGC) • 1 GB program memory, 15" LCD • USB, Ethernet, Wi‑Fi • HaasConnect remote monitoring • VNC, DPRNT support • Early power‑failure detection, program restart from any block • Run Stop Jog Continue, SafeRun collision mitigation • Electronic handwheel, memory lock • Fourth-axis readiness: • VF‑YT 4th‑axis preparation • 4AXD: 4th‑axis drive, connections, and wiring • Note: Rotary table not included • Software options: • DWO/TCPC (Dynamic Work Offsets & Tool Center Point Control) • HSM (High‑Speed Machining with look‑ahead) • Probing cycles and SO, MACRO, COORD, VPS functions • Axis travels and feeds: • Spindle nose to table: 102–610 mm • Rapids X/Y/Z: 35.6 m/min • Max cutting feed: 21.2 m/min • Max thrust X/Y: 8.87 kN; Z: 13.7 kN • Worktable: • 914 × 457 mm • T‑slot table, 16 mm slots, 125 mm spacing • Spindle: • Direct drive, spindle cooling, taper air blast • Rigid tapping • Tool changer: • Side‑mounted ATC, 30 + 1 tools • Max tool Ø (all pockets): 63.5 mm • Max tool Ø (adjacent empty): 127 mm • Tool‑to‑tool: 1.8 s; chip‑to‑chip: 2.4 s • Accuracy: • Positioning ±0.005 mm; repeatability ±0.003 mm • Ballscrew thermal compensation • Coolant and probing (integrated options): • P‑COOL: Programmable coolant nozzle • TSC: Through‑spindle coolant 21 bar, 22 l/min • WIPS‑R: Wireless workpiece and tool probing system • Machine features: • Fully enclosed machining area (sliding front doors, hinged side windows) • Coolant system with pull‑out tank • Automatic central lubrication • Compressed‑air connection • Machine work light Additional equipment • AUGER: Screw‑type chip conveyor • ACF: Auxiliary coolant filtration system, 25 µm • COOLANT MAINT PACK: Coolant maintenance package • COOLANT REFILL: Automatic coolant replenishment system (requires external water supply) • Enclosure mist extraction / mist condenser (as supplied) • OIL‑SKIMMER: Coolant tank oil skimmer Rodpfx Ako Abap Njisch • CHIP STRAINER: Mesh filter and metal chip basket set • LK: Machine lifting kit with lifting accessories and brackets Technical Specification Taper Size ISO 40

Condition: new, Year of construction: 2026, Weima Hacker / Shredder WL 8 with Top Features - 2nd knife row, log spacer, 4-sided segment base, discharge auger with gear motor, Fast reverse hydraulics with shock valve The single-shaft shredder WL 8 is a proven classic for shredding wood waste of all kinds. It is used, for example, thousands of times in woodworking companies worldwide. The high number of these highly sought-after shredders guarantees proven and reliable technology at the best price-performance ratio. The machines are characterized by their very robust design, which ensures extremely high durability (even outdoors). Intuitive operation thanks to Siemens PLC control with touch display To ensure that the electronics are optimally adapted to the machine, we design, build and wire our control cabinets ourselves. We use only high-quality components – for example, from Siemens or Rittal. Intuitively operated touch surfaces guarantee quick adjustments. Functions such as adjusting the slide timing or stop ensure a high throughput. The built-in overload protection also prevents damage to the machine. No material bridging due to self-cutting hopper design The hopper performs several tasks at once. First, the material to be shredded is fed into it – manually, mechanically or via a conveyor belt. The generous opening also makes it easy to fill very large parts. However, its special design, which is rounded at the front and thus effectively prevents material bridging, is crucial for the shredding process. Even with bulky parts, the shredder cuts itself free. If required, both hopper extensions and lids with gas spring are available. Durable rotor bearings thanks to offset design A rotor bearing must be particularly robust due to its extreme stress during the shredding process. To prevent dust or foreign objects from entering it, we have separated it from the machine frame. This also makes it very easy to maintain and access. Rotor diameter (mm): 260 Rotor length (mm): 1000 Rotor speed (RPM): 80 - 125 Power (kW): 22 Number of knives: 54 Available knife sizes (mm): 40 x 40 Grain size (mm): 15/20 mm or according to customer requirements Suction nozzle (mm): 200 Feed opening (mm): 1000 x 1250 Length (mm): 2045 Width (mm): 1740 Height (mm): 1840 Weight (approx. kg): 2200 Accessories: - 2nd knife row - Log spacer - 4-sided segment base - Discharge auger with gear motor - Fast reverse hydraulics with shock valve - Screen size 15/20 mm List price: €52,320, sold at a special price Location: In stock at 54634 Bitburg - available immediately - Rcsdpopdqzxsfx Akijh The pictures show a machine without a discharge auger; one will be available in stock.

Condition: used, Year of construction: 1976, number of stapling heads 1 Rcjdev Ach Ropfx Akish

Year of construction: 1973, condition: like new (used), Used BRONX Heavy Duty Initial Pinch Pyramid bending rolls. Year of manufacture : 1973. MACHINE FORMERLY INSTALLED AT ROLLS ROYCE PLC IN DERBY UK. IMMEDIATELY FOR SALE AND NOW LOCATED IN BELGUIM WHERE IT CAN BE INSPECTED. SPECIFICATION CAPACITY Two sets of dimensions which are shown below as "Prebending & Rolling" and then "Rolling only". Material Mild Steel Mild Steel Tensile strength 28/32 tons/sq.in 28/32 tons/sq.in Maximum width 11’(3350mm) 11’(3350mm) Maximum thickness at this width 2” (50mm) 2½” (63.5mm) Minimum inside diameter of rolled cylinder at maximum capacity 30’ (762mm) 37 ½’ (953mm) Maximum thickness of plate when hot rolling (finished rolling temperature 850° C.) 4” (102mm) 5” (127mm) Minimum inside diameter of rolled cylinder at maximum capacity hot rolling 40” (1016mm) 50” (1270mm) Rsdpfxeh U Rzge Akisch MAIN PARTICULARS Diameter of all rolls - 27” (686mm) Body length of rolls - 11’2”(3403mm) Rolling speed - 12 f.p.m. (3600mm/min) Main drive motor - 150 H.P. Slip Ring Type Two bottom roll adjusting motors, each - 50 H.P. Slip Ring Type Combined operation of swing down bearing and top roll counterbalance - Hydraulically applied Hydraulic power pack motor - 10 H.P. Electrical equipment to be suitable for operation on a supply of - 400/440 volts, 3 phase, 50 cycles CONE ROLLING ATTACHMENT: To facilitate the rolling of taper or conical forms, a skid plate is fitted to the inside of the non-drive end housing. ELECTRICAL EQUIPMENT Motors: Main Drive - 150 H.P. half hour rated – slip ring screen protected – foot mounted type. Bottom Roll Adjustments - 50 H.P. half hour rated – slip ring screen protected – foot mounted type. Hydraulic Power Pack Motor - 10 H.P. continuously rated – Squirrel cage – screen protected – foot mounted type. Control Gear: Main Drive - Drum type reversing control gear with 5 minute rated wire wound resistances, designed to pass 100% full load on the first notch or operating position in each direction. The controller will be fitted with off position interlock and limit switch rings where necessary. Bottom Roll Adjustments - Drum type reversing control gear with 5 minute rated wire wound resistances designed to pass 100% full load on the first notch or operating position in each direction. The controllers will be fitted with off position interlock and limit switch rings where necessary. Hydraulic Power Pack - Direct-on-line contactor type starter, operated from a maintaining type push button station. Solenoid valves for operating cylinders are push button operated. Note: Full protection to be provided for all the above control gear by a circuit breaker, incorporating overload and no-volt protection. FEATURES AND EQUIPMENT Spare Roll included with the machine. LENGTH TBA MM WIDTH TBA MM HEIGHT TBA MM WEIGHT 95 tonnes NOTE: The information contained herein is provided in good faith, but however due to unforeseen errors or omissions cannot be binding as to accuracy.

Year of construction: 2023, condition: used, Welding System Manufacturer: TRASKO Type: CMT 1 Year of manufacture: 2023 Control system: Siemens Rcsdpfxjzbvnfj Akioh Technical data: - Voltage: 400 V, 50 Hz - Current: 63 A Technical features: - Robotic MIG welding of individual components onto a cooling plate - Automatic torch cleaning and wire cutting - Rotary table with 2 stations for loading/unloading during the welding process In our assessment, the robotic welding system is in mint condition. Accessories, tools, and clamping devices shown are included in the scope of delivery only if specified in the additional information. Subject to technical changes, errors, and prior sale.

Condition: used, mileage: 99,900 km, power: 88 kW (119.65 HP), first registration: 11/2020, fuel type: diesel, overall weight: 3,000 kg, color: white, gearing type: mechanical, emission class: euro6, number of seats: 3, total length: 5,300 mm, Equipment: air conditioning, central locking, soot filter, Chat with us now via WhatsApp: Get in touch quickly and easily with our sales consultant. Attention!!! Sales preferably to commercial customers. Rcedpfxey D Dk Ue Akieh Internal ID number: [ 3408 ] ----Optional extras: * 12–64 months warranty (valid throughout the EU) * New inspection * New TÜV (technical inspection) & emissions test * Nationwide delivery * Financing possible even without a down payment * Spring offer: Upon request and for an additional charge of only €999, increase the trailer load to up to 3,500 kg (vehicle and manufacturer dependent). ----Vehicle highlights: * 19% VAT can be shown * Regularly maintained * German vehicle * Immediately ready for use * First owner * Euro 6 standard * Accident-free * Long wheelbase (L2) * LED daytime running lights * Loading area with wooden lining * Trailer coupling 2,500 kg * Air conditioning * Reversing camera * Reinforced springs * Bluetooth multimedia system * 3 seats Special equipment: Rear parking aid, rear wing doors without glazing (opening angle 250 degrees), wooden floor in the loading area, complete wheel covers, headlights Full-LED with LED signature C Other equipment: Airbag driver side, anti-slip regulation (ASR), exterior mirror electrically adjustable and heated, battery 85 Ah, on-board computer, rev counter, automatic switch-on for headlights, omission of keyless entry, glove compartment with cooling function, interior filter: pollen filter, body/structure: standard van, fuel tank: 80 liters, loading area partition, steering column (steering wheel) adjustable, model update, engine 2.0 liters - 88 kW dCi Diesel Energy, fog light, radio preparation, wheelbase 3498 mm, tire repair kit, low emissions according to emission standard Euro 6d-TEMP, sliding door loading/passenger compartment right, seat cover / upholstery: fabric, seats in the driver's cab: double passenger seat, seats in the driver's cab: driver's seat comfort 3-way adjustable, start/stop system engine, daytime running lights LED, lashing eyes in the loading area on the side, pre-wiring for electrical installation, heat-insulating glazing ----Do you want to lease or finance? We offer attractive deals – even without a down payment! Feel free to contact us. Contact: Phone: Email: Location: Nutzfahrzeuge West GmbH Rudolf-Diesel-Str. 2 45711 Datteln – Germany Opening hours: Mon-Fri: 9:00 a.m. – 6:00 p.m. Sat: 9:00 a.m. – 2:00 p.m. ----Note: All information on the Internet is non-binding and serves only as a general vehicle description. Errors, typos and prior sale are reserved. The binding condition of the vehicle results exclusively from the purchase contract on site or through written assurances. We prefer to sell vehicles with a mileage of more than 50,000 km or older than 3 years to our commercial customers.

Year of construction: 2023, condition: new, Cable stripping maschine ,wire stripper Technical Data: Dimensions: W / H / D 75 cm / 68 cm / 86 cm Rcjdpfsk Ra Tuex Akioh Weight: app. 95 Kg Color: blue / yellow Cutting speed: app. 48 Meter per Minute Engine: 230V / 3000 W

Condition: as good as new (ex-display), Year of construction: 2024, New hydraulic heating plate press Manufacturer: ITALPRESSE, Type XL/6 30-13 with gold-anodized plates Touch display control - Electric heating plates, 3,000 x 1,300 mm - Total pressure: 90 tons - Number of heating plates: 2 pcs. - Number of tiers: 1 pc. - Cylinder stroke: 350 mm - Tier opening: 350 mm - All-side loading - Number of pressure cylinders: 6 pcs. - Diameter of pressure cylinders: 85 mm - Power requirement of hydraulic unit: 3 kW - Electric heating plates made of solid, hard aluminum with built-in heating wires - Heating power: 22 kW - High-pressure insulation plates Rcededx R Tfepfx Akijh - Working temperature: 90° C - Max. temperature: 120° C - Operating voltage: 400 V/50 Hz - Safety regulations according to CE standard Standard equipment: - Movement of the press table with rack and pinion and parallel guides at 2 corners of the press table, made of self-lubricating material - Electronic control unit with touch screen for controlling and monitoring the machine - Digital timer for setting the pressing time and automatic opening - Digital input and monitoring of the pressing pressure - Digital timer for setting the pressing time - Digital diagnostics and display of error messages - Safety circuit with two-hand operation - Safety pull cord - Safety bracket for the lower press table Integrated accessories: - Touch screen TS/400 - EFC Electronic flatness control - Gold-anodized heating plates (bus bars) Location: In stock at 54634 Bitburg - Immediately available -

Condition: ready for operation (used), Year of construction: 2012, functionality: fully functional, machine/vehicle number: 27878-01, type of input current: three-phase, input frequency: 50 Hz, input current: 2,900 A, ABB Limited low-voltage main switchgear / main distribution switchboard Year of manufacture: 2012 Rsdpfx Aezz I T Eekioch Type: Low-Voltage Main Switchgear / Main Distribution Switchboard Nameplate data: Supply: 415 V AC, 3-phase, 4-wire, 50 Hz Auxiliary circuit voltage: 240 V AC Main busbar rating: 2900 A Main busbar fault level: 50 kA for 1 second (nameplate). The site equipment card also states 55 kA for 1 second. Degree of protection: IP31 Conformity: BS EN 60439-1, BS EN 60947-1, 73/23/EEC, CE Main breakers: ABB SACE E2 air circuit breakers (ACB) Interconnection ACB to Section C busbars Withdrawable PDU outgoing modules Metering / instrumentation cubicles with digital meters Associated with Transformer 1C / PDU distribution. Some compartments are marked Danger 11 000 V (HV / transformer cable side). Manufacturer: ABB Limited, Hanover Place, Sunderland, England, SR4 6BY. Condition: used, installed in a plant room. Price on request. Nameplate and cubicle photos available.

Condition: new, Wireless communication adapter (modem) for transmitting Ethernet, PROFINET or Modbus TCP data signals over a wireless Bluetooth or Wi-Fi connection in an industrial environment. Rcjdpfx Ae Afdwlokijh

Condition: excellent (used), Year of construction: 2017, functionality: fully functional, machine/vehicle number: 591.063.060.0016, workpiece weight (max.): 1,500 kg, travel distance X-axis: 550 mm, travel distance Y-axis: 350 mm, travel distance Z-axis: 400 mm, table width: 600 mm, overall weight: 2,800 kg, table length: 900 mm, Equipment: documentation/manual, The CUT P 550 model from 2017 is an advanced five-axis wire EDM machine, ideal for precise industrial applications: * wide angular range capabilities (up to 30–45°), Rcsdpfxowwrtwj Akish * efficient and intelligent IPG generator, * accuracy within a few µm, * advanced automation systems and anti-collision protection, * stable, durable design enabling fully automatic operation.

Condition: new, Year of construction: 2026, Hydraulic winch HAW1700 with electric valve incl. manual operation and radio remote control for mounting on wood splitters, cranes, mini excavators, tractors, forklifts, mowing tracked vehicles, and telescopic loaders, for use in viticulture and horticulture, agriculture, construction, and forestry, as well as many other applications. Equipped with an electric hydraulic valve and radio remote control. The hydraulic winch HAW1700 can simplify many tasks. Maximum rope capacity of 30 m with 6 mm wire rope. Standard equipment includes 20 m of 6 mm wire rope. ⦁ Pull and position firewood for the wood splitter Redpfx Ajfn Tvhekisch ⦁ Pull logs onto a trailer ⦁ Pull out tree stumps and trees ⦁ As an auxiliary winch on skidders and small excavators ⦁ As a winch for small tractors and narrow-gauge tractors A robust steel construction with the possibility of mounting on both sides (bottom, rear, top) with M12 threads. This allows for flexible use of the winch. Large, double-bearing rope pulley for long wire rope life. The pulling force is 1700 kg as standard. The winch can be installed in various positions. An optional hydraulic brake is available. Depending on the required pulling speeds and forces, we can offer you different options. Please contact us, and we will be happy to advise you. ⦁ Maximum working pressure: 225 bar peak ⦁ Continuous operating pressure: 175 bar ⦁ Displacement: 400 ccm ⦁ Torque at 225 bar: 870 Nm peak ⦁ Torque in continuous operation: 380 Nm ⦁ Maximum pulling force: 1700 kg ⦁ Weight: 49 kg ⦁ Rope speed: 47 m/min at 60 l/min oil flow ⦁ Color: red ⦁ Including hoses from the valve to the motor Dimensions: ⦁ Length: 500 mm ⦁ Length with rope inlet: 570 mm ⦁ Front width: 120 mm ⦁ Rear width: 180 mm ⦁ Bearing width: +30 mm ⦁ Motor width: +200 mm ⦁ Height: 250 mm Included: Radio remote control for the winch. ⦁ Control range: up to 100 m ⦁ Temperature: -35 °C to +80 °C Protection class: IP65

Condition: ready for operation (used), Year of construction: 2024, travel distance X-axis: 610 mm, travel distance Y-axis: 400 mm, travel distance Z-axis: 450 mm, controller manufacturer: HEIDENHAIN, controller model: TNC7, spindle speed (max.): 5,000 rpm, number of axes: 3, This 3-axis KUNZMANN WF 610 CNC was manufactured in 2024. It features a longitudinal travel of 610 mm, transverse travel of 400 mm, and vertical travel of 450 mm. The machine is equipped with a 20-station tool changer and a maximum table load of 300 kg. If you are looking to get high-quality milling capabilities, consider the KUNZMANN WF 610 CNC vertical machining centre we have for sale. Contact us for further details. Rsdpfx Ae Af Nzujkioch - Demonstration machine- Spindle Hours: 332 h- Program Run Hours: 310 h- Feed Rate (Rapid Traverse): X/Y/Z up to max. 30/30/15 m/min - Main Drive (Option Installed): SK 40 Motor Spindle, 1 - 12,000 rpm (Swiss made) - Spindle Power: 8.5 kW (S1-100% ED) / 11.5 kW (S6-40% ED) - Spindle Torque: 43 Nm (S1-100% ED at 1,880 rpm) / 58 Nm (S6-40% ED at 1,880 rpm) - Tool Interface: SK 40 DIN ISO 7388-1 Form AD (formerly DIN 69871 AD) with pull stud DIN ISO 7388-3 Form AD (formerly DIN 69872) - Tool Clamping: Mechanical, clamping force 10,000 N, hydraulic release - Vertical Milling Head: Direct-driven, manually tiltable -5/+90°, extendable quill with turnstile (stroke 70 mm, clampable) - Rigid Angle Table Surface: 800 x 425 mm - Table T-Slots: 6 x 14 H7 (pitch 63 mm) - Max. Table Load: 300 kg - Tool Changer: 20-station disc magazine, SK 40 - Max. Tool Diameter: 75 mm (full magazine) / 150 mm (with adjacent empty pots) - Max. Tool Length: 250 mm - Max. Tool Weight: 8 kg - Tool Change Time: approx. 3 s (chip-to-chip approx. 15 s) - Positioning Accuracy (ISO 230-2): 0.008 mm (direct linear measuring systems) - Repeatability (ISO 230-2): 0.006 mm (direct linear measuring systems) - Measuring System: HEIDENHAIN absolute direct linear measuring system (resolution 0.001 mm) - Coolant Through Spindle (IKZ): 50 bar high-pressure pump (26 l/min), 4-stage pressure adjustment (15/25/40/50 bar), 25 µm double switch filter - Internal Air Cooling: Through-spindle air cooling, M-function programmable - External Air Cooling: Flexible articulated hose, M-function programmable - Paper Band Filter Unit: Trommel-mulden filter with 600 l external tank, type VDF150/50/50 (150 g/m²) filter fleece (dimensions: 1800 x 860 x 1620 mm) - Chip Conveyor: Hinge-belt conveyor integrated into 115 l coolant tank, 60° incline, lateral discharge left (height 870 / 1060 / 1200 mm) - Workpiece Probe: HEIDENHAIN TS 460 3D probe (infrared) with SE 661 transceiver - Additional Axes Preparation: 4th axis preparation (axis controller in electrical cabinet, pre-wired interface) - Automation Interface: Preparation kit for EDUCATION4.0 Cobot cell (Harting connector I/O interface, pneumatic connection, plus 2x pneumatic table connections max. 6 bar) - Enclosure Door: Automatic sliding front door driven by belt drive (manual push button & programmable) - Software Option: OCM (Optimized Contour Milling) for advanced trochoidal milling - Handwheel: HEIDENHAIN HR 510 FS electronic handwheel with axis selection and emergency stop - Operating Voltage: 400 V, 50 Hz - Power Consumption: approx. 21 kVA - Control Voltage: 24 V - Compressed Air Supply: 6.5 - 10 bar (min. 6.5 bar required at machine) - Machine Weight: approx. 2,900 kg (with tool changer)

Condition: used, functionality: fully functional, The Dibipack 4255 EV from Italdibipack is a small, microprocessor-controlled shrink wrapping machine. Automatic adjustment of the sealing temperature to the operating cycle guarantees stable and consistent seams. The shrinking process, combined with the simultaneous sealing of the film, is completed in a single operation. The product is placed inside the film and then drawn into the shrink chamber. The hood is now manually closed and held in place by an electromagnet. The automatic cycle then begins, during which the film is sealed around the product and shrunk, conforming closely to the product's shape. The shrinking is achieved by heating the air, which is simultaneously circulated by a fan. Once the process is complete, the hood opens automatically, and the finished, packaged product can be removed. For bagging products, the film can be sealed without subsequent shrinking. Up to 8 different work programs can be stored via the control panel. Parameters such as shrink temperature, shrink time, and the sealing time of the sealing strip can be easily and conveniently adjusted on the operating panel. An electronic counter informs you about the product flow. A mobile base, which makes the Dibipack 4255 EV even more flexible, is available as an accessory. The Dibipack 4255 EV can be used to process PVC, PE, PO, LDPE, OPP, CP films, all sealable films, as well as micro-perforated and food-grade films. Rcsdpfx Ake Afdmyjieh The machine has undergone a thorough inspection in our in-house workshop and is fully functional. Upon request, a video of the machine can also be sent. You will receive an invoice with VAT shown. Our used equipment service for you: 6-month warranty on electrical parts, limited to the replacement of defective parts, without installation and removal costs. High-quality branded equipment at fair prices. Professional refurbishment / inspection & expert cleaning. Checked & fully functional - or your money back. Flexible options for shipping or self-collection. Competent advice - before and after purchase. Provision of operating instructions, wiring diagrams & spare parts. Inspection according to DGUV V3. Technical data: Max. output per hour: 240-360 pieces Power connection: 230 V - 1 phase Rated power: 3 kW Working table height with base: 920 mm Sealing frame L x W: 550 x 420 mm Max. product height: 200 mm Machine dimensions, L x W: 1,235 x 750 mm Max. film width: 600 mm Max. film roll diameter: 250 mm Machine weight: 87 kg Condition: used, fully functional Further details: Up to 8 different work programs can be stored. Microprocessor-controlled processes. Energy-saving standby function. Hood opening system with gas spring. Electronic counter. Quick and easy adjustable film unit for different product sizes. Processing of different films. Shipping: Delivery or self-collection by arrangement. Worldwide shipping on request. Shipping to islands or mountain stations only by arrangement. Subject to change and errors.

Condition: refurbished (used), Year of construction: 2005, travel distance X-axis: 1,050 mm, travel distance Y-axis: 2,050 mm, travel distance Z-axis: 1,000 mm, workpiece weight (max.): 20,000 kg, table width: 1,140 mm, table length: 1,640 mm, workpiece length (max.): 2,520 mm, workpiece width (max.): 1,520 mm, workpiece height (max.): 945 mm, feed rate Z-axis: 12 m/min, overall weight: 30,000 kg, table load: 20,000 kg, # OPS INGERSOLL GANTRY 1500 / 64 Bit ## Fully Refurbished – Completion Expected 10/2026 For sale is an OPS INGERSOLL wire EDM machine, model GANTRY 1500 / 64 Bit, manufactured in 2005, which is undergoing a comprehensive and professional overhaul in our facility. Rcodpez Atdrofx Akioh Upon completion of the overhaul, the machine will be in very good condition, both technically and aesthetically, and will be prepared for immediate use in reliable production operations. ### Technical Data Manufacturer: OPS INGERSOLL Model: GANTRY 1500 / 64 Bit Year of Manufacture: 2005 Condition: Fully Refurbished Completion: Expected 10/2026 Control: Mitsubishi – 64-bit CNC Generator Power: 70 A – Multipulse Travel Ranges X / Y / Z: 1,050 × 2,000 × 1,000 mm Electrode Changer: 15-position pick-up disc changer Working Tank (W × D × H): 1,520 × 2,520 × 945 mm Workpiece Clamping Table (W × D): 1,380 × 2,380 mm Load Capacity: 20,000 kg ### Accessories * CO₂ fire extinguishing system * Cartridge filter system ## Extensive Overhaul The OPS INGERSOLL GANTRY 1500 is undergoing a comprehensive and professional overhaul in our facility. During the overhaul, the machine will be disassembled to over 70%. All relevant components and wear parts will be carefully inspected and, if necessary, professionally refurbished or replaced. ### The following overhaul work will be carried out: * Inspection and, if necessary, replacement of the ball screws and ball bearings of the X, Y, and Z axes * Inspection and, if necessary, replacement of all four ball screws of the tank drive * Inspection and testing of the C-axis for tightness and accuracy * Geometric inspection of all axes according to the OPS INGERSOLL test protocol * Thorough cleaning of the entire machine base * Cleaning of the entire working tank, including replacement of the felt wipers * Overhaul of the dielectric pumps * Replacement of all hydraulic and dielectric lines * Replacement of all pneumatic lines * Thorough cleaning of the control cabinet, generator, and control system * Replacement of all relevant fans and batteries * Overhaul or, if necessary, replacement of power supplies, units, and servo amplifiers * Final laser measurement of the machine after the overhaul ## Quality Control and Erosion Test After completion of all overhaul work, the machine will undergo a comprehensive functional and quality control. This includes, in particular, a detailed erosion test according to the quality and testing specifications of OPS INGERSOLL. The relevant machine functions, as well as accuracy and process reliability, will be checked. ## Ready for Production After Overhaul After successful completion of the overhaul and final inspection, the OPS INGERSOLL GANTRY 1500 / 64 Bit is immediately ready for use. With its high load capacity of 20,000 kg, the generous travel ranges, and the large working area, the machine is particularly suitable for the reliable machining of large and heavy workpieces in demanding production environments. A powerful and comprehensively refurbished wire EDM machine for users who value high machine quality, process reliability, and long-term operational capability. 10/16.

Condition: ready for operation (used), Year of construction: 2015, operating hours: 3,343 h, travel distance X-axis: 1,626 mm, travel distance Y-axis: 1,016 mm, travel distance Z-axis: 762 mm, controller manufacturer: HAAS, total height: 3,282 mm, total width: 4,039 mm, table width: 914 mm, table length: 1,626 mm, table load: 1,814 kg, overall weight: 11,250 kg, spindle speed (max.): 8,100 rpm, spindle motor power: 22,400 W, number of slots in tool magazine: 40, tool weight: 5,400 g, product length (max.): 4,827 mm, number of axes: 3, This 3-axis Haas VF-8 vertical machining centre was manufactured in 2015. It features an impressive X-axis travel of 1626 mm, Y-axis travel of 1016 mm, and Z-axis travel of 762 mm. The machine includes a robust table size of 1626 x 914 mm and a maximum table load of 1814 kg. If you are looking to get high-quality machining capabilities, consider the Haas VF-8 vertical machining centre we have for sale. Contact us for further details. • CNC control • Haas CNC control, Classic generation • 15-inch colour LCD • USB port • Program memory: 1 MB • Remote jog handle with colour display • Axis travels and feed rates • Spindle nose to table distance: 102–864 mm • Rapid traverse (X/Y/Z): 15.2 m/min • Maximum cutting feed rate: 12.7 m/min • Worktable • Table dimensions: 1626 × 914 mm • Max evenly distributed table load: 1814 kgSpindle • Spindle taper: 40 taper • Maximum spindle speed: 8,100 rpm • Spindle power: 15 kW • Two-speed gearbox • Spindle cooling system • Spindle taper air blast • Rigid tapping • Tool changer Rcsdpfx Ao Adz Iljkieh • Side-mounted tool changer: 40 positions • Coolant and chip removal • Through-spindle coolant: 20 bar, 22 L/min • ACF additional coolant filtration system: 25 µm • Programmable coolant nozzle position • Coolant system with pull-out coolant tank • Screw-type chip auger • Probing and machining options • WIPS-R wireless workpiece and tool probing system • Tool length and radius measurement • Workpiece measurement and setting cycles • PMDS probe interface, internal power supply and wiring • Spindle orientation, coordinate rotation and macros • VQC Visual Quick Code conversational programming • HSM High-Speed Machining with look-ahead for machining complex contours using three-axis interpolation • 4AXD fourth-axis preparation, including connections and wiring. Rotary table not included • APC-READY automatic pallet changer preparation, including eight additional functions, macro support and wiring. Pallet changer not specified as included Additional equipment • Ball screw thermal compensation • Fully enclosed machining area with sliding front doors and hinged side windows • Program memory lock • Compressed-air connection • EPFDM early power failure detection module • Automatic central lubrication • Machine lighting • CABCOOL CNC control cabinet cooling unit Technical Specification Taper Size ISO 40 Through-spindle Coolant Yes