Step feeder

MS-Maschinenbau STS

Condition: reconditioned (used), functionality: fully functional, approx. 4.5 m long infeed and centering table Drive via chain from the feed motor Centers the logs in the middle of the rotor Debarking machine VK 26 4 main cutters 4 pre-cutters 30 KW main motor 11 KW feed unit non-driven extraction table Machine workshop checked Iajdeu Hmacjpfx An Uor Machine cleaned and repainted

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Iaedpfx Aowp Rqfjn Ujr Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Condition: new, Year of construction: 2023, Application combs 10 mm Application combs 15 mm Application combs 20 mm finger joint profile 15 mm Iedeiacbpspfx An Ujar finger joint profile 20 mm delivery time 3 days

Condition: ready for operation (used), Slab recovery line with below machines: Isdpfxegwqk Se An Uear One 2-blade board edger One single blade horisontal resaw Conveyors system between the machines included.

Condition: good (used), Year of construction: 2000, functionality: fully functional, Holtec Bruks long log intake system with root reducer, consisting of: Cross infeed conveyor with 6 chain strands, split drive. Holtec hydraulic step feeder with split drive. Iedpowxck Aofx An Uoar Bruks root reducer type RR 1200 for long logs – milling length 1200 mm. Holtec heavy-duty conveyor belt for round timber. Scraper conveyor for waste removal and distributor auger.

Condition: excellent (used), Weinig four-sided planer Iodpsrigxysfx An Uear max planing width 230mm max planing height 120mm 5 heads, bottom-5,5KW; left and right-11KW, top-11KW, bottom-5,5KW feed - 4KW fully adjustable heads electrically adjustable up and down and planing width 40mm spindles feed on gimbal rollers, with smooth adjustment WEINIG brand solid planer, length of the machine 415cm machine checked in original condition

Condition: used, Eccentric punch press HAULICK + ROOS type RVD 125 double column - eccentric press Machine No. 212560 Year of construction 1981 pressure force 125 ton. table size 880 x 800 mm table opening 470 x 140 mm column width 900 mm column width lateral 415 mm ram stroke 45 mm slide adjustment travel 0-80 mm Installation height on the picture 340 mm Stroke rate 50 to 300 strokes/min. Motor power main drive 22 kW Mains connection 380 volt, 50 Hz - Double connecting rod drive with 4-fold eccentric shaft for off-center ram pressure load - adjacent electrical cabinet - NC roll feed EBU, width 250 mm, year 2003 - adjacent control panel for roll feed - strip running direction from left to right space requirement (press) L x W x H 3000 x 2000 x 3020 mm transport height 2950 mm Iaedpfohlnzksx An Uer weight of the press approx. 11 ton.

Condition: used, Söderhamns Rotary Debarker Cambio 85 - 66 - A Diameter: 10 - 66 cm Main motor: 30 kW Ijdpfoxtc Afsx An Usar

Condition: new, *TECHNICAL SPECIFICATION: Heating capacity: up to 36 kW per consumer circuit Cooling capacity: up to 30 kW per consumer circuit at -30°C Load circuits: 1 or 2 as standard Temperature range: - 45°C to +130°C Medium: water / glycol mixture Dimensions LxWxH (without connections) : 1-circuit: 1950 x 1280 x 1725 mm 2-circuit: 2150 x 1640 x 1725 mm Weight: Isdjg Ezarspfx An Uear 1-circuit: approx. 1300kg 2-circuit: approx. 1500kg *HIGHLIGHTS EQUIPMENT: -Controls: Temperature control (standard) -Control via SPS with touch screen -Analogue and digital interfaces -Internal 2-circuit pump system (INFO: Ensures performance values even at low flow rates) -Heating control via solid-state relay (SSR) -Flow measurement in the internal circuit for flow monitoring (INFO: If the water/glycol mixture is incorrect, the system automatically warns and switches off in the next step) -Pressure-controlled cooling water regulator (INFO: Much more accurate than temperature controls) Stainless steel tank, corrosion-resistant components (stainless steel/non-ferrous metal) (non-ferrous metal-free optional) All medium-carrying components and piping insulated for low-temperature application -Water-cooled condenser (air-cooled on request). *OPTIONS: -flow rate control: up to 100l/min, >4 l/min +/- 5% of measured value -Pressure control: 0.5 to 4.5 bar (control range) -compressed air monitoring -test piece emptying by means of compressed air - Cooling water monitoring -Limitation of inlet pressure -Other special options available on request and after technical inspection Visit our website for more details or for other performance classes. *This unit conforms to the European Directives. Other directives and standards are only fulfilled if they are listed in the order confirmation. This technical specification reflects the standard equipment, customer requests deviating from the standard will be shown in quotations or order confirmations.

Condition: used, Year of construction: 2007, Liebherr A924b-957 litronic TIER 3 OVERHAULED Year of manufacture: 2007 Iasdpfx Asyt Idpsn Uer Liebherr engine 127kW Tier 3 / EPA 8 solid tyres 10.00-20 Gumasol Dozer blade Industrial mono boom 6.80m Industrial angled stick 5m Operator's cab hydraulically elevating Cabin with front protection grille Radio system Air-suspended driver's seat Positioning swing brake Lift cylinder damping Lift cylinder with pipe rupture protection Overload warning device Generator drive mounting kit DRIVELINE WARRANTY