Belt Conveyor Kleemann

Condition: reconditioned (used), Year of construction: 2016, functionality: fully functional, power: 389.81 kW (529.99 HP), Mobile shredder DOPPSTADT AK 560 Eco Power Diesel engine: 530 HP Fine shredding basket (hole size can be agreed) Phsdpfew Rz Rqex Aa Esa Rear discharge conveyor with magnet roll (magnetic head pulley) Twin drive (separate drives for scraper floor and infeed roller) Hydr. self propelled drive (for moving on site) Radio remote control

Condition: reconditioned (used), Year of construction: 2012, operating hours: 25,895 h, functionality: fully functional, pressing force: 78 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 24,000 kg, oil tank capacity: 1,000 l, power: 55 kW (74.78 HP), volume flow: 930 m³/h, Technical data baler: Manufacturer Presona AB Typ LP 80 VHK 1 Year of construction 2012 Total machine operating hours 25,895 hours, as of July 2025 Pump operating hours, effective 14,135 hours, as of July 2025 Number of bales pressed 235,597 pieces, as of July 2025 Pedpfjvwlqqsx Aa Eoha Press power main press 78,5 tons Specific press capacity 95 N/cm² Press power of pre-press 28 tons Volume of pressing chamber 2,7 m³ Feed channel1,500 x 1,100 mm Theoretic throughput rate 930 m³/h Throughput rate under operating conditions 410 m³/h Bale size 750 x 1,100 mm Driving motor 55 kW Tying system 5 fold vertical, 3-fold horizontal, full automatic Throughput rate with a bulk density of 30 kg/m³ approx. 9 to 12 tonnes/hour, depending on material 50 kg/m³ approx. 14 to 17 tonnes/hour, depending on material 100 kg/m³ approx. 16 to 25 tonnes/hour, depending on material Throughput capacity with MSW (Municipal Solid Waste) approx. 20 to 27 tonnes/hour, depending on material Bale weight 450 up to 600 kg, depends on material and bale length Volume hydraulic oil tank 1,000 l Baler dimensions built up with hopper 10,985 x 3,750 x 4,310 mm (l x w x h) Transport dimensions only baler 10,985 x 2,300 x 2,900 mm (L x w x h) Machine weight baler approx. 24 tons Condition of the press: The machine was partially overhauled and serviced in our workshop and, once the work was complete, tested in manual and automatic mode during operation. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Wire station with deflection rollers for the lower wire cleaned and made operational Side guides removed from the press ram, smoothed, mounted and readjusted Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical and horizontal needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Door contact switch checked and partially replaced. Emergency stop switch checked. Complete electrical wiring checked and partially replaced. Bearings of the wire guide rollers under the press replaced. New safety grilles for vertical and horizontal binding manufactured and installed. Machine checked, general maintenance work carried out and press tested in manual and automatic mode Scope of delivery: Only the baler will be sold. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: ready for operation (used), An air-conditioned office and commercial container Aztech is available. U-value: approx. 0.38W-0.46W/m²K, floor load capacity: approx. 100kg/m², interior height: approx. 2500mm, external dimensions X/Y/Z: approx. 3000mm/3000mm/2600mm, weight: approx. 800kg. Documentation available. An on-site inspection is possible. Podpfx Aajw D Eubj Ejha

Year of construction: 2004, condition: good (used), Manufacturer: Hein Lehmann Pedoh Ty Tqspfx Aa Eeha Type: LF 2,0 – 6,30 / 30 ED Size: 2.000mm x 6.300 mm Decks: 1 Year of Manufacture: 2004 With Frame.

Condition: excellent (used), Year of construction: 2007, operating hours: 21,676 h, functionality: fully functional, pressing force: 78 t, filling opening width: 750 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 25,000 kg, transport height: 3,000 mm, oil tank capacity: 1,000 l, power: 55 kW (74.78 HP), empty load weight: 25,000 kg, volume flow: 930 m³/h, operating pressure: 250 bar, How do you do? We are pleased to offer you a used baler of the manufacturer Presona AB, type LP 80 VH1. The following technical data was taken from the manufacturer's operating instructions and brochures, for which we cannot accept any liability for correctness and completeness. Manufacturer Presona AB, Sweden Type LP 80 VH1 Year of manufacture 2007 Total operating hours, 21,676 hours, as of November 2024 Main press force 78 t Podpfxevgrh Ue Aa Esha Specific pressing force 95 N/cm² Pressing force of prepress flap 28 t Dimensions of feed chute 1,500 x 1,100 mm Filling volume / pressing cycle 2.7 m³ Throughput capacity under operating conditions 410 m³/hour Bale dimensions 1,100 x 750 mm Drive power 55 kW Tying 5-fold vertical Hydraulic oil tank volume 1,000 L Baler dimensions assembled with hopper 10,985 x 3,750 x 4,310 mm (L x W x H) Machine weight press approx. 25 t Note: The machine was used by a recycling company to compact paper, cardboard and film. The press is in good condition, in operation until January 2025 and can be inspected by appointment. We would be delighted if this machine is of interest to you. Your service team Mertens & Frowein GmbH

Condition: used, Year of construction: 2012, power: 264 kW (358.94 HP), Stationary shredder M&J 4000S. Electric drive: 2x 132 kW 400 V AC, 50 Hz Phjdpfx Aasu Dkf De Eoa Inkl. substructure, hydraulic unit, control cabinet.

Condition: used, Year of construction: 2006, operating hours: 9,237 h, Equipment: all wheel drive, Equipment: * Year of manufacture: 2006 * Operating hours: 9,236 h * Power: 157kW / 213 hp * Weight: 19.8 t * Tires: Michelin 23.5-25X Type A approx. 60% * Reversing camera * Steering wheel control * Air conditioning * Tow pin * Central lubrication system * Suspension seat * Radio pre-installation Other details: * 1 previous owner * German machine * CAT service records maintained Pedpfx Aeu D Uvyja Eeha * Last service at 9,003 h * Signs of use * Rust present Since 1972, your reliable partner for all matters concerning automotive and commercial vehicles in 28832 Achim am Bremer Kreuz. NutzfahrzeugZentrum Behnke continuously offers approx. 200 vehicles, including vans, commercial vehicles, and construction machinery! We continuously offer attractive financing options with special low rates. If interested, we will be happy to provide you with an individual quote! Trade-in of your commercial vehicle/construction machinery is welcome. If a new TÜV inspection is required, we are happy to provide you with an offer from our partner workshops. Our offers generally come WITHOUT a new TÜV inspection. Delivery of your "new" commercial vehicle can be arranged by our external partners for an additional fee. The information provided in advertisements, on the internet, price tags, and images are non-binding descriptions and do not constitute guaranteed characteristics. The seller accepts no liability/warranty for typing or data transmission errors. Equipment listed may require separate verification. Subject to prior sale and errors.

Condition: used, operating hours: 20 h, Fuel type: Diesel Phsdsuu Df Djpfx Aa Eoa

Condition: good (used), Manufacturer: Främbs & Freudenberg Type: 2000-6000-2 Deck size 2.000 x 6.000 mm Number of decks: 2 Pedpfsg Snvbex Aa Eoha Included: – Electrical Motor – Cardan Shaft – Springs Vibrating screen can be overhauled, sandblasted and painted.

Year of construction: 2025, condition: new, Description: Screening deck system consisting of 1 decks for screening waste wood or wood chips. input material 0-200 mm capacity approx. 80 m³/h (depending on material) material is separated into 2 fractions 0-25 mm and oversized material Psdpfx Asg I Uqfsa Ejha to be mounted on customer's own baffle walls or underframe Technical data: Screen deck 1: length = 5,200 mm; width = 1,215 mm o Outer dimensions: length = 5.500 mm width = 1.850mm o Screen surface 6,3 m², number of shafts 40 pieces o Drive 2 x 7,5 kW gear motors o Screen body polyurethane (star screen) D 166 / 12 fingers o Screen shafts as plug-in system (adaptation to other grain sizes easily and cost-efficiently possible) o Lubrication of the bearings to the outside, optional central lubrication against surcharge possible