Frame Saw with Oscillating Frame

Esterer LSH

Year of construction: 1979, operating hours: 10,968 h, condition: ready for operation (used), functionality: fully functional, machine/vehicle number: Werk-Nr. 8725, INFORMATION REGARDING SALES AND CONTRACT CONDITIONS: MACHINE CONDITION: This ESTERER frame saw, model LSH 65, was in impeccable operational use until three years ago and remains serviceable. The equipment includes both a stationary control panel in front of the saw frame and a mobile control panel on the tensioning carriage. A hydraulic tensioning device for adjusting the saw blades in horizontal and vertical directions is mounted on the frame. The electric motor drive with gearbox is included in the offer. HANDOVER AND PRICE: Handover will take place after full payment of the purchase price. The price is ex foundation and is payable on-site directly to the seller after conclusion of the contract and prior to dismantling. WARRANTY: The seller assumes no warranty, neither before nor after handover of the machine – sold as seen. The buyer has no right of withdrawal. Tjdpfjzgr Iqox Akisd DISMANTLING: Complete dismantling, including lifting gear, tools, and transportation, is the responsibility of the buyer. Handover of the machine shall take place on-site. Any damage caused to the building during dismantling will be repaired by the buyer or charged separately. The purchase transaction will be mutually confirmed by means of a sales contract.

Condition: used, Year of construction: 2017, machine/vehicle number: LC560, Used Processing Line for small dairy products 2000 L/h Milk Reception and Initial Storage The Used Processing Line for Small Dairy Products 2000 L/h begins with a milk reception unit consisting of two Lactofreeze tanks and a receiving pump. Initially, operators channel raw milk into the tanks, where it remains chilled. As a result, the system ensures thermal stability before processing. Furthermore, this setup minimizes the bacterial load while allowing continuous transfer to the pasteurization stage. Pasteurization and Separation Next, the pasteurization phase uses a plate heat exchanger with a retention section and auxiliary systems, all rated for 2,000 liters per hour. Specifically, the pasteurizer rapidly heats and holds milk at a predefined temperature to eliminate pathogens. Then, the GEA WESTFALIA separator—rated at 3,000 L/h—performs cream separation. Simultaneously, the RANNIE homogenizer (1,000 L/h) reduces fat globules, thus enhancing emulsion stability and preventing cream rise. Fermentation and Coagulation Following thermal treatment, the milk proceeds to fermentation. Here, operators use an insulated double-wall fermentation tank with a 1,000-liter capacity and planetary agitator. Consequently, they maintain uniform bacterial activity and precise temperature control. In parallel, a 1,000-liter coagulation vat equipped with a planetary mixer initiates the curdling process. Both tanks ensure optimal protein structuring for yogurt, cheese, and cultured cream products. Cheese Processing and Draining After coagulation, the Used Processing Line for Small Dairy Products 2000 L/h continues with cheese processing. The system includes a 500-liter vat with a draining sieve and two cheese draining tables. Therefore, operators can efficiently handle large curd volumes. Moreover, these components simplify whey separation while ensuring sanitary compliance. Additionally, their design supports easy cleaning and cross-contamination prevention. Packaging Operations Once products are ready for packing, the line integrates semi-automatic and automatic solutions. First, a semi-automatic filler doses pasteurized milk into 1-liter bags. Subsequently, the yogurt cup filler automatically fills and seals 75 mm and 95 mm cups at up to 1,800 units per hour. Meanwhile, the rotary labeling machine by ETICAP (2004) applies both front and rear self-adhesive labels on cylindrical cups. Importantly, the machine ensures consistent alignment and adhesion. Tedpfx Akew Ahg Reisd Date Coding, Thermal Control, and Final Packing In addition, a Videojet 1220 coder (2019) applies expiry dates onto each product via belt conveyor. Further downstream, a vacuum packaging machine handles cream and cheese portions. Thermal utilities include a 115–150 kW solid fuel boiler (2014) with dual transfer pumps. At the same time, an ice water tank (5,000 L, 2014) and a cooling unit (2018) maintain temperature consistency across the line. Laboratory and Accessories Alongside processing units, the Used Processing Line for Small Dairy Products 2000 L/h features a dedicated laboratory. Specifically, it houses analytical tools for quality control and milk analysis. Additionally, the line includes 300 plastic crates for storing and transporting yogurt cups. System Shutdown and Storage Finally, operators shut down the line in September 2023. Before dismantling, they cleaned ...

Condition: used, Year of construction: 1976, Esterer LSH Sash Saw 1976 - Automatic cantilever adjustment - Hydraulic roller lifting - Swing frame - With templates Tedpfoyhduysx Akiod - With magnetic holder - With Jansen saw tensioner - With Esterer Arta-C riving knife - With drive motor - With saw blades - With intermediate gear Clearance width: 650 mm Clearance height: 90–620 mm Stroke: 500 mm Feed speed: 0–8 m/min Feed power: 3.5 kW Pulleys: 900 mm Total weight: 5.4 t Fits the foundation of the Esterer LD65 sash saw. Has been stationary for around 15 years. Dismantled and stored approx. 3 years ago. Annual cut approximately 3,000 solid cubic meters. Very good condition – immediately available – fully functional Location: Austria, near Graz

Condition: good (used), Hydraulic unit for Esterer LSH saw gate, manufactured in 2006 Type: RP 63 WÜ Tedpfxsg R Sm Do Akijd Feed mechanism for LSH also available Fully functional – in good condition – immediately available Location: Austria, near Ried im Innkreis Please also check out my other listings. I look forward to your inquiry.

Condition: refurbished (used), Year of construction: 2024, Overhauled: 2024 Control: SPS Siemens S7 Saw blade max: 500 mm motor power 4,0 KW Saw blade feed: 0-40 mm/ s continuously adjustable Saw height control electronic Working range square 90° max.: 130 x 130 mm Working range flat 90° max.: 190 x 130 mm Working range round 90° max.: 170 mm The machine has been completely overhauled in our company and is in mint condition. Among other things, the following points were renewed: Conversion to Siemens S7 PLC control Conversion to Siemens HMI user interface Conversion to pusher with servo control New electrical components New pneumatic lines New pneumatic components Conversion to valve terminal Optimization of the suction capacity New minimum lubrication system Replacement of general wear parts Overhaul of the cab The machine also has Tedjuiy Ngepfx Akijd Minimum quantity lubrication Splitting extension (for a high-quality cutting surface without return marks) Pre-loading magazine for gentle handling of painted/anodized surfaces Offcut ejector in the pusher Foldable offcut tray Optional: Magazine width 3000mm Pusher length 6000mm Pusher length 8000mm Reinforced motor 5.5 kW Mass clamping device for parallel sawing of several workpieces Online support connection Delivery and installation on your premises Training of your employees

Condition: excellent (used), Spare parts for Esterer log carriages LSH 65, some in new condition, new and used. Tsdsi T Egpopfx Akijd Flywheels, stanchions, hydraulic cylinders, chain drives, feed gears, guides, solenoid valves, overhanging parts. Saw frame, top and bottom, saw carriage with insertion brackets. Pulleys. Spare parts also available for Esterer log carriages SS 71.

Condition: excellent (used), functionality: fully functional, ARI high capacity line for big logs Log deck 2 sections Step feeder Log conveyor Debarker infeed (Remill) Debarker Cambio 90-75/6 (or a Cambio 500) 2d scanner for reject boxes Log conveyor with 2 reject boxes Log conveyor, kickers to the left Buffering deck and step feeder Log conveyor Rema 3d scanner AriVislanda LT2 auto log turner 2006 AriVislanda LI-600 log centering infeed 2006 AriVislanda RL-600 Reducer AriVislanda QSS-700 Saw 2011 Tedpfx Akswp E Tneijd AriVislanda VFW 600 L 2011 AriVislanda board separator 2006 Block tilt AriVislanda block infeed type Nils AriVislanda RC-600 Reducer Ingvar Persson turn table AriVislanda 500A Infeed AriVislanda 509-7F Multirip AriVislanda boardseparator Beltconveyor Dual Edging lines Söderhamn (1 left 1 right) 2 x 300 m/min Cross conveyors Söderhamn Elevator Söderhamn 483 Scanners Söderhamn 528 Infeed Söderhamn 5100 Edger Söderhamn 5400 Edger outfeed with reject displacement EdgeIT system

Year of construction: 2023, condition: new, machine/vehicle number: PRJ065955, ALZMETALL bench drill press, drilling capacity in steel: 12 mm Drill chuck mounting: B16 external taper, spindle stroke: 40 mm, overhang: 200 mm, column diameter: 50 mm, usable table surface: 300x240 mm, with T-slots 2 x 12 mm x 80 mm, distance spindle-base plate min./max. 110/250, manual feed, machine height without options: 670 mm, net weight: 64 kg. - Speed infinitely variable 250-5000 rpm Standard equipment: 5" TFT-LCD display with touch function: manual input of target spindle speed, display of actual speed, integrated depth gauge with touch function for zeroing, virtual depth scale on the display, machine status indicators and warning messages on the display, service information, selectable operating language DE/EN/FR/ES/IT/NL/RU Tedpfx Akelub Rdeiod AC motor 230 volts, 50 Hz, connection plug pre-assembled, cable length 2 m, three separate buttons for clockwise rotation - counterclockwise rotation - stop, Spindle stop via braking function, spindle guard with electrical protection, main switch lockable, mushroom push button (self-locking) for EMERGENCY STOP, speed adjustment continuously variable via potentiometer, protection class IP54, spindle guard with electrical protection, paint finish: DD textured paint signal white RAL 9003, PANTONE 7545c, black including the following options: LED machine light, item no. 12. Delivery time: from stock, Waiblingen/Beinstein

Condition: used, Type: PI 21 Number of needles: 21 Needle diameter: 4 mm Max product: width 250 mm Tact per minute: 15 to 55 tact/min. Passage mechanism type: gear rack rail Product passage height: 220 mm Brine pressure: 0,5 to 4,0 bar Tsdpfsh Dm Spox Akied Electric power: 1.5 kW Machine dimension in cm: Width: 70 Lenght: 140 Height: 176 Delivery time: 30 working days after advanced payment

Condition: like new (used), Year of construction: 2016, power: 200 kW (271.92 HP), overall weight: 7,500 kg, MEBOR multi-blade line with two drums, model VC700, manufactured in 2016. In very good working condition! Almost new. The multi-blade line includes: 1. Automatic feed conveyor with automatic positioning rollers. 2. Loading ramp. 3. Unloading table with left/right sorting. Tjdpfx Asy Sganokijd