Spot welding machine

DALEX PMS 16-1

Condition: refurbished (used), DALEX roller seam welding machine, cross seam version Projection: 350 mm Bcjdpodx Suhofx Aa Uew Nominal power: 160 kVA Sec. short circuit current: 38.5 kA Sec. no-load voltage: 4.8-9.6 V Electrode force: 140-2,040 daN with 2-step switch and auxiliary control with thyristor power stage and Synchronous welding control MPS 100 multi SPECIAL NOTE - PLEASE NOTE The above performance data are taken from the machine's rating plate. When the machine was inspected, it was found that a 200 kVA welding transformer was installed by the previous owner. This changes the performance data. .

Condition: new, Year of construction: 2025, functionality: fully functional, type of input current: AC, Spot Welding Machine Type KAP10 CE certified Operated: Pedestal Power at 50% ED 10kVA, Continuous power 7.1kVA Welding Capacity: 1.5+1.5mm steel sheet Bcodpfxekwcbyj Aa Ujw Transformer Construction: -Primary winding: Copper wire -Secondary winding: Copper flexible foil sheet -Core: Silicon steel EI core Mains Connection: 220V/400V (50Hz) Protection Fuse: 220V-40A / 380V-25A Power Level: 5 Arm Length: 500mm Arm Diameter: 40mm Electrodes: Adjustable electrode stroke Power Input Cable: 3m Protection Class: IP21 Space Requirement (W/L/H): 380mm x 1000mm x 1050mm Weight: 110Kg Warranty: 1 years (+10 years spare parts support)

Year of construction: 2012, condition: ready for operation (used), An Autobond laminating system for sheet-shaped and heat-resistant products is available. Laminating speed: 60m/min, min. sheet dimensions X/Y: 285mm/320mm, max. sheet dimensions X/Y: 1060mm/1060mm, paper thickness range: 90g-650g/m², min. laminating film thickness: 24µm, max. roller pressure: 6t, max. temperature pressure water unit/control: 140°C/135°C. Machine dimensions X/Y: approx. 4000mm/1600mm, weight: approx. 2000kg, operating hours: 28785h. Documentation available. An on-site inspection is possible. Bodoxbrw Uepfx Aa Uscw

Condition: excellent (used), Year of construction: 1980, WAFIOS DF5 Wire range- 1,5- 5,0 mm Mesh with - 20 - 100 mm Working with - max.2000mm Bcjdpfx Aev Uw Ddja Uow Capacity - 170 m2 / hour Tooling for the mesh width - 60 mm

Condition: excellent (used), Year of construction: 1984, functionality: fully functional, equipped with: 1 slide feeding system right hand side 1 eccentricpress 250 kN 4 standard slide units 2 narrow slide units 1 cam shaft working range: wire diameter range: 0,5 - 5,0 mm stripmetal width: max. 40 mm feeding length: up to 320 mm outout: up to 135/min Bcodpfx Aetzlzaoa Ujw

Condition: used, Year of construction: 1970, machine/vehicle number: 120895, pressure:63 t throat:250 mm stroke:8 - 100 mm no. of strokes:120 Hub/min table::715 x 500 mm dayligth:330 mm ram adjustment:63 mm clamping plate:700 x 480 mm Bcedpfxefx Hv Hj Aa Usw hole in the table:240 mm Hole in clamping plate:110 mm dimension of ram:450 x 280 mm weight of the machine ca.:5,5 t dimensions of the machine ca.:1,2 x 1,7 x 2,7 m hydraulic tilting single column eccentric press, tilting in 4 steps, opening to rear (325 x 500mm) and below (360x160mm) with central lubrication via hand pump, additional clamping plate 700 x 480 x 850 mm, two-hand operation, foot-trip operation possible, operating-mode selector for adjustment of continuous or single stroke, emergency cut-off, piece counter, various accessories

Condition: excellent (used), Year of construction: 1984, functionality: fully functional, equipped with: 1 slide feeding system right hand side 1 eccentricpress 250 kN 4 standard slide units 2 narrow slide units 1 cam shaft working range: wire diameter range: 0,5 - 5,0 mm Bsdpfx Aorwnyvja Uocw stripmetal width: max. 40 mm feeding length: up to 320 mm outout: up to 135/min

Condition: good (used), Year of construction: 1992, Favretto MB 130 – Technical Specifications Machine type: tangential (horizontal) surface grinding machine Year of manufacture: 1992 Table size: 1700 × 400 mm Magnetic chuck size: approximately 1300 × 400 mm Magnetic plate height: 40 mm Longitudinal travel (X-axis): 1380 mm Cross travel (Y-axis): 450 mm Bcedet Rwvzspfx Aa Usw Vertical travel (Z-axis): 550 mm Distance between spindle center and table surface: 203 mm (min) to 753 mm (max) Grinding wheel dimensions: 400 mm diameter × 152 mm width × 100 mm bore Spindle speed: approximately 1400 rpm Longitudinal feed rate: 2000 to 40000 mm/min Cross feed rate: 50 to 3000 mm/min Vertical feed rate: 700 mm/min Grinding head motor power: approximately 15 kW Total installed power: approximately 25 kW Maximum table load without magnetic chuck: approximately 1500 kg Maximum table load with magnetic chuck: approximately 1205 kg Overall grinding capacity (L × W × H): approximately 1500 × 600 × 550 mm Machine weight: approximately 7100 kg

Year of construction: 2001, condition: good (used), Universal CNC Turning Lathe from Pinacho apply for toolmaker , mold maker, education and Locksmith Turning diameter : 360mm Control : Fagor 8055 Technical data Turning diameter 360mm Turning lenght 1000mm Control Siemens Fagor 8055 Tailstock MK 3 Tools Barufaldi 6 pice Speeds 1-4000U/min Bcjdpfxsfglzgj Aa Uow Power supply 380V - 5,5 KW Contact person: AWM GmbH Herr Mario Wurm

Year of construction: 1978, condition: used, pressure 100 t throat 380 mm stroke 400 mm power capacity 22 kW Bcjdpfolp U Dpjx Aa Usw dayligth 600 mm ram surface 600x500 mm table surface area 720x600 mm weight of the machine ca. 9 t