Straight-through drilling machine

BIESSE

Condition: ready for operation (used), functionality: fully functional, TECHNICAL DETAILS DRILLING UNITS Spindles for vertical drilling: 30 Spindles for horizontal drilling in X-direction: 6 Spindles for horizontal drilling in Y-direction: 4 Total number of vertical + horizontal spindles: 40 MILLING SPINDLES Number of controlled axes: 4 Motor power: 12 kW GROOVING UNIT Maximum tool diameter: 120 mm TOOL MAGAZINE 1 Number of positions: 22 Tool: positioned on the rear side of the machine TOOL MAGAZINE 2 Number of positions: 8 Tool: positioned on the head MACHINE DETAILS Year of manufacture: 2009 Width: 4,300 mm Length: 2,200 mm Total installed power: 42 kW EQUIPMENT Automatic panel loading system Lift table Automatic panel stacking system With motorized transfer Vacuum pump Blsdpfoyq Ez Tox Agzsd Machine programming software: BIESSEWORKS

Condition: ready for operation (used), Year of construction: 2008, functionality: fully functional, workpiece height (max.): 90 mm, workpiece width (max.): 3,200 mm, workpiece length (max.): 3,200 mm, edge thickness (max.): 3 mm, The machine has the following configuration: Number of panel sizing/milling units on the left side: 5 Milling unit (AS10) Bsdpfxsyq Avhe Agzold Double finishing cutter, top and bottom 2 pre-milling units Milling unit Number of edge processing units: 10 End trimming Top and bottom trimming (rough) Fine trimming for chamfering and rounding Corner rounding (AR34, 4 motors) Edge milling (FB40, 1 motor) Edge scraping Belt sanding (1 motor) Glue scraping Polishing (2 motors) Spray device TECHNICAL DETAILS Minimum panel height: 10 mm Maximum panel height: 90 mm Maximum panel length: 3,200 mm Maximum panel width: 3,200 mm Minimum edge thickness: 0.4 mm Maximum edge thickness: 3 mm FEATURES Feed chain with carriers Pressure applied via rubber belt Panel guide rails with NC positioning Edge roll magazine with 6 positions Hot melt adhesive system for PUR adhesive NORDSON Roller set for edge pressing 4 pressure rollers with NC positioning Spray device mounted on upper cabinets The machine is sold and delivered in its actual and legal condition ("as seen and approved") based on photo documentation and descriptive technical/commercial documents. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, securing, and operation of the machine at the destination. External reference: 7685

Condition: ready for operation (used), Year of construction: 2011, functionality: fully functional, travel distance X-axis: 6,200 mm, travel distance Y-axis: 1,935 mm, workpiece height (max.): 250 mm, number of axes: 4, number of spindles: 40, TECHNICAL DETAILS Working area X-axis: 6,200 mm Working area Y-axis: 1,935 mm Maximum panel thickness: 350 mm Number of vertical drilling spindles: 28 Number of horizontal drilling spindles in X-direction: 4 Number of horizontal drilling spindles in Y-direction: 8 Total number of drilling spindles: 40 Total number of tool change positions: 22 Number of suction traverses: 10 Bsdeyqzrnjpfx Agzsld Milling unit Number of axes: 4 Motor power: 10.5 kW Automatic tool changer Edge banding unit Gluing unit Tool magazine Grooving unit Number of positions in tool magazine: 22 MACHINE DETAILS Main spindle power: 10.5 kW Total power: 31 kW EQUIPMENT Vacuum pump Safety net Chip conveyor The machine is sold and delivered in its actual and legal condition ("as seen and approved") based on photographic documentation and descriptive technical/commercial documents. The buyer has the right to inspect the goods before collection and shall be responsible for the installation, securing, and use of the machine at the place of destination. External reference: 8011

Condition: used, machine/vehicle number: 008389, X axis working area: 8417 mm Y axis working area: 1930 mm Working Table: Pod and Rail Main Electrospindle power: 13.2 KW Number of controlled axes: 4 axes Maximum edge height: 60 mm Bodeyqxxrjpfx Agzsld Total number of drilling spindles: 40 Total number of tool changer positions: 22

Condition: used, machine/vehicle number: 008374, Max. panel width: 1000 mm Blodjyng Amopfx Agzod Max. panel length: 2500 mm

Condition: used, machine/vehicle number: 008437, Type of edging: Thin edge, Thick edge Gluing System: EVA Hotmelt, PUR Bedpsyng Agjfx Agzjld Premilling Unit: yes Corner Rounding Unit: yes Max feed speed: 12 m/min Maximum panel thickness: 60 mm Operating Units: 7 nr

Condition: used, machine/vehicle number: 008438, Max. panel width: 4500 mm Max. panel length: 4500 mm Main saw blade projection: 60 mm No of Grippers: 8 Bledpfxeyngy Se Agzsd

Condition: used, Year of construction: 2009, Used machine Year of manufacture: 2009 Single-sided automatic edge banding machine with CNC control, 10" touch screen Bjdpfx Aov R Nk Usgzsld Industrial conveyor chain 1 1/4" Joint milling unit FI-502 Glue application unit VC-710 End trimming unit IN-801 Top and bottom flush trimming unit RS-100 2 motorized multifunction profiling units - contour milling unit CR-202 (FAST system with 4 standard positions) Scraper unit RBK-503, NC 2 positions Flat scraper RCC-701 Workpiece thickness: 10-65 mm Max. workpiece height with contour milling unit (depending on profiles): 35-65 mm Edge thickness from roll: 0.4-3 mm Edge thickness from strip material: 0.4-22 mm (depending on unit) Minimum workpiece length: 140 mm Minimum workpiece width (with length 140 mm): 85 mm Minimum workpiece width (with length 250 mm): 50 mm Feed speeds: 10-14-18-20 Central extraction connection: 200 mm Extraction connection, edge banding: 80 mm Extraction connection, joint milling: 120 mm Glue pot capacity: approx. 3 kg Heat-up time at half fill: approx. 10 min Length: 6000 mm Width: 1780 mm Height: 1770 mm Machine is offered without the workpiece return unit shown in the pictures Availability: short-term Location: Flörsheim

Condition: used, The BIESSE SAND REGAL 1350 is an industrial wide belt sander designed for calibration and fine sanding of flat components in the furniture and panel production industries. The REGAL series represents a robust production solution suitable for medium to high production volumes. Bsdpfxoynb Rfs Agzold The machine features a modular design, allowing for a combination of calibration and finishing operations in a single pass, which significantly increases productivity.

Condition: excellent (used), Year of construction: 2003, functionality: fully functional, Working area 2,893 x 950 mm 6 traverses with 12 suction cups Milling spindle with ISO 30 tool holder, 3.6 kW, Drilling unit: 10 vertical drills 6 horizontal drills Grooving saw, 6-position tool changer. Blsdpfx Agsymmr Eszjd Control unit N500 Color display Total connected load: 10 kW 400 V, 50 Hz