Hammermill

Aubema 2508

Condition: used, Eldan Granulator HG129 Godpst Uyvrjfx Afkobn

Condition: good (used), Year of construction: 1999, Overhead crane, crane, electric hoist, manual trolley, trolley, crane trolley, crane trolley, crane trolley, trolley, girder trolley, monorail trolley, hoist -Manufacturer: Steel, crane chassis with electric cable winch -Cable pull: Type AS 3016-16 2/1 -Load capacity: 3200 kg -Main stroke: 8 m/min -Fine stroke: 1.35 m/min -Drive system: FA-C 3728 133-1 -Travel speed: 5/20 m/min -Roller spacing: 1400 mm, dimensions see photos -Drum speed: 16.0 / 4.0 m/min -Quantity: 1 crane trolley available Gsdpetlzdqsfx Afkjbn -Price: per piece -Transport dimensions: 1670/1200/H470 mm -Weight: 462 kg/unit

Condition: used, Year of construction: 2013, functionality: fully functional, Fisher+Rueckle FZR-24 Veneer cross-gluing machine, year 2013 for sale! Veneer strip length 400-1100 double lane/ 350-2100 mm single lane Veneer strip width 50-500 mm Veneer strip thickness 0.3-1.5 mm Max nominal output /machine cycles 30 cycles/min Average production speed 17-20 cycles/min Gbedeumrf Aspfx Afkjn Effective length of heating zone 2478 mm Connection power 22 kW Compressed air 6 bar Glue types PVA or UREA based

Condition: as good as new (ex-display), Year of construction: 2025, operating hours: 500 h, functionality: fully functional, machine/vehicle number: 25-029, total width: 800 mm, total length: 4,700 mm, total height: 1,900 mm, type of input current: three-phase, energy consumption: 2 kWh, Very good metal separator (inductive sorter) for separation of all kinds of metal (incl. stainless steel). Can be used before ECS, behind or stand alone. Ejecting of all metals larger 0.5 / 1 mm possible. Reasonable using for material up to 60 % metal content. Unique flap technology, no pressured air necessary. Machine is ready for using, can be visited or tested. If wished can be equipped with camera. Gbsdpfx Afeqabm Eeken If the machine is too small we can build also bigger. It is our demonstration machine. Throughput / capacity depending on material and purpose. Price on negotiation!

Year of construction: 1986, condition: not inspected (used), 6 head rotating vacuum capper rebuild 2017 Gbedpfxsf Rk Ago Afken as-is or tested and adjusted to customer needs.

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, overall weight: 36,000 kg, oil tank capacity: 1,300 l, year of last overhaul: 2025, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Gbjdpfx Afjvf E Avskjn Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: excellent (used), ZEISS Type: DSM 962 The digitized scanning electron microscope DSM 962 is equipped with an integrated 4 MB image memory, a 40 MB hard disk for internal image storage and drives for external storage of data and images. hard disk for internal image storage and drives for external storage of data and images. This makes it possible to quickly and easily gain insights into the composition and morphology of morphology of specimen surfaces far into the sub-micrometer range. With magnification range from 5x to 300,000x, both macrostructures and microstructures can be examined. Gsdpfx Aofcwwnofkebn as well as microstructures is possible. The range of applications can be extended considerably by adding special accessories, allowing, for example analytical investigations in micro areas of the surface are possible. The device can be operated both via conventional switching elements and via the keyboard or mouse (add-on). or mouse (add-on). Electron optics and vacuum control are conventional. Functions of the Image memory functions are operated using the keyboard or mouse (add-on). A separate information screen is located centrally on the separate information screen for displaying the menus. These operating instructions are intended as a guide to help the user achieve the best possible results with the device. results with the appliance. The explanations have been kept as simple as possible so that even a less experienced user less experienced users the necessary tools. Magnification range: 20x to 300,000x at 7 mm working distance Stages in a sequence of 1-2-3-5-10 Minimum magnification: 5x at 50 mm working distance Resolution: 4 nm - guaranteed with tungsten cathode at 30 kV, 6 mm working distance, untipped specimen 25 nm - guaranteed with tungsten cathode at 1kV, 6 mm working distance, untipped specimen 3.5 nm - guaranteed with optimal LaB6 cathode at 30 kV, 6 mm working distance, untilted specimen Scope of delivery: (DSM 962 with accessories as shown) Condition: used (Subject to changes and errors in technical data and specifications) Please ask about transportation options before purchasing. We will be happy to answer any further questions you may have over the phone.

Year of construction: 2010, condition: good (used), 2 SICON shredders Godeiz Tm Iopfx Afkobn Year 2010 The electrical cabinet is missing Price 15 000€ each 4 densimetric tables : 8 000€ each

Condition: ready for operation (used), Number of blades: 6, rotor diameter: 350mm, engine power: 50kW, with construction as steel/welded construction in reinforced design and documentation, an inspection is possible, year of construction unknown, was overhauled in 2022. Gbsdpfx Afen Tpmujkjn

Year of construction: 2004, condition: ready for operation (used), Max. working width: 1000mm, feed rate: 5-20m/min, height: 2200mm, length: 4000mm, weight: 3.3t, with documentation, was maintained regularly. Gbodpei E Trpjfx Afken