Panel saw with 4 controlled axes

Altendorf F45 ELMO IV plus

Condition: new, Year of construction: 2022, New machine Year of manufacture: 2022 Standard Equipment: - Electrically powered height and tilt adjustment (0–46°) with automatic correction of cutting height during tilting - Eye-level, swiveling control panel - Double roller carriage, carriage length 3,000 mm - Manually adjustable rip fence with scale, including manual fine adjustment, max cutting width 1,000 mm - Crosscut fence with fixed 90° position, manually adjustable via scale up to 3,200 mm - Max saw blade projection: 150 mm - Max saw blade diameter: 450 mm - Drive power: 4 kW (5.5 HP) at 4,000 rpm - AKE main saw blade clamping system - Working height: 91 cm Motor 5.5 kW (7.5 HP) with VARIO F45: - Stepless speed control from 2,000–6,000 rpm - Precise speed adjustment to the material increases cutting quality and blade service life Extended Cutting Height for Single-Side Tilting: - This option enables single-side tilting with a large extraction hood for max blade Ø 550 mm and a blade projection of up to 204 mm - In combination with a scoring unit: max blade Ø 500 mm / max cutting height 179 mm - Only available in conjunction with at least 5.5 kW (7.5 HP) drive power 2-axis Scoring Unit for Tilting: - With motorized height and lateral adjustment, programmable scoring blade height with quick lowering and raising - Drive motor 0.75 kW (1 HP), 8,200 rpm - Retrofitting only possible on machines prepared for the scoring unit LED Lighting: Rjdpsw I Uxcsfx Acvor - Highly energy-efficient LED technology for clear marking of the scoring area The Altendorf double roller carriage is renowned for its smooth operation and precision run. It can be locked steplessly in any position. The large double rollers, precision-manufactured from hardened steel, ensure the upper carriage remains absolutely accurate in conjunction with the lower carriage on the hard-chromed guide bars. This running quality is maintained even after decades of heavy use and exposure to dirt. The carriage construction features a highly rigid, torsion-resistant multi-chamber design. The table surface is finely planed and anodized. A hard-chromed round bar in the upper carriage serves as both the mount for the cross-slide and the interface for various accessories. The entire unit is low-maintenance and does not require lubrication. On/Off Switch on Double Roller Carriage: - The on/off switch on the double roller carriage is always within easy reach. With four buttons, both the main saw blade and the scorer can be switched on and off, saving time and increasing safety. Angle/Mitre Fence, Crosscutting up to 3,500 mm: - This Altendorf-patented fence with integrated length compensation makes it easier to cut angles and mitres precisely in a single operation. In both positions, the swivel angle is steplessly adjustable by up to 49° and displayed on a scale. The play-free and robust stop flaps can easily be moved and adjusted as a single flap over the entire area up to max. 3,500 mm.

Condition: excellent (used), Robland 3200 silver line format saw with a trolley Rodpfx Aov S Hy Aocvjr scoring saw with a separate engine, trolley length 320cm main engine 7KW 3 speeds max disc 450mm 0-45 tilt electrically adjustable with readout up-down saw electrically adjustable without readout culaga on the right side motorically adjustable up to 1240mm digital readers on the culaga on the trolley angle device included Branded machine in very good condition,

Condition: reconditioned (used), Year of construction: 1987, functionality: fully functional, machine/vehicle number: 9673240, grinding width: 1,100 mm, power: 15 kW (20.39 HP), height adjustment type: electric, grinding belt length: 1,900 mm, compressed air connection: 6 bar, grinding belt width: 1,120 mm, Combination sanding unit with contact roller and air sanding pad Brush roller Pneumatic sanding belt tensioning Motorized thickness adjustment Technical data max. working width 1100 mm max. workpiece thickness 150 mm min. workpiece thickness 3 mm Sanding belt dimensions 1900 x 1120 mm Feed speed 5/10 m/min. Motor power sanding unit 15 kW Motor power height adjustment 0.50 kW Motor power feed carpet 0.5/1.0 kW Operating pressure 6 bar Rjdpfxotppzvj Acvor Air consumption approx. 20 l/min Suction nozzle 2 x 200 mm Weight approx. 2100 kg Machine width approx. 1750 mm Machine depth approx. 1700 mm Machine height approx. 1900 mm

Condition: new, Year of construction: 2026, Combined saw-milling machine minimax st 3c F 16 Swiveling saw blade, swiveling milling spindle and format sliding carriage made of anodized aluminum Sturdy cast steel construction Large support surface and precise cast table High-precision sliding carriage made of anodized aluminum (travel 2250 mm) Large trimming frame (900 x 600 mm) with telescopic aluminum fence extendable up to 2660 mm with professional stop flaps Max. Saw blade Ø 315 mm with scoring device, tiltable from 90° - 45 Saw parallel fence with fine adjustment Stable saw unit and large dimensioned double cradle milling unit guarantee highest stability, precision, smooth running and long service life Solid and precise machine table made of stress-free gray cast iron Three milling speeds, manually adjustable from 3500 - 10000 min-¹ With right-left rotation of the milling spindle Standard arc milling protection hood Safety turning stop jaws made of aluminum Two motors with high power reserves Two plug-in handwheels for convenient and quick operation Dimensions and weights Weight approx. 470 kg Connection suction Rsdpfjhp Rdlox Acvsr Suction port diameter 2 x 120 mm Suction port diameter saw blade guard 60 mm Electrical data Power drive motor 2 x 5,0 kW Supply voltage 400 V Mains frequency 50 Hz Milling spindle spindle inclination 0 - -45 ° useful length of spindle 100 mm spindle speeds 3500/7000/10000 min-¹ Milling tool diameter max. not lowerable 210 mm lowerable 180 mm tenon milling 275 mm K

Condition: used, Thickness planer: Max planing width: 400 mm Max planing height: 240 mm Min length of planed workpiece: 200 mm Cutter shaft diameter: 700 mm Number of knives: 3 Cutter shaft speed: 5000 rpm Manual adjustment of working height Jointer: Total table length: 1810 mm Adjustable tables Cutter shaft noise suppression Cutter shaft guard Extraction port: 2x120 mm Tilting fence Supply voltage: 400 V Motor power: 5 kW Overall dimensions: Length: 2030 mm Width: 800 mm Height: 1160 mm Rsdsxwvqdspfx Acver

Condition: used, Year of construction: 2018, Used machine Year of manufacture: 2018 Special feature: Machine for up to 100 mm edge height! Condition: Factory-inspected by Lange Maschinenbau Equipment and technical data: - Machine table with 13 running rollers for improved workpiece guidance - Edge feeding, synchronous with belt feed - Edge thickness adjustable via digital counter - Pneumatic roller separation with knife (for cuttable edges) - Three pressure rollers - Belt feed: - 0.25 kW - approx. 1250 mm long - approx. 6.0 m/min - 50 mm wide toothed belt with thick, workpiece-friendly rubber top - Digital counter for height adjustment - Direct glue application to the workpiece: drip-proof glue pot with glue supply from below and rapid heat-up time after standstill - Flush cutting unit: - for front and rear workpiece edges - automatic sensing at the workpiece - pneumatic cutting with knife for cuttable edges - Flush trimming unit - with vertical sensing and horizontal guidance - reproducible setting using digital counters - 2 powerful 0.4 kW high-frequency motors - stepless speed adjustment from 4000 to 18000 rpm - Cutter Ø 70 mm, Z4, radius 2 mm/15° - central extraction nozzle Ø 100 mm - 2 chip extraction hoods with hose Ø 60 mm - Automatic height adjustment of the upper cutter with belt feed - Continuous workpiece support approx. 1800 mm long - Workpiece support rail, extendable by approx. 300 mm - Rotatable foil dispenser Ø: 800 mm - Workpiece width: min. approx. 80 mm - Workpiece thickness: 10 – 100 mm - Workpiece length: min. approx. 220 mm - Edge thickness: 0.4 – 2.0 mm - Roller separation: max. 1.0 x 55 mm, 2 x 45 mm - Glue pot heating capacity: 2.7 kW - Heat-up time: approx. 10 minutes Rodpewka S Iofx Acvjr - Working height: approx. 880 mm - Electrical connection: 400V, 50 Hz, 3Ph + N - Total connected load: 3.8 kW - Pneumatic connection: 6 Bar Dimensions (without foil dispenser): approx. 1800 x 700 x 1300 mm Weight: approx. 260 kg Availability: short-term Location: Flörsheim

Condition: used, Year of construction: 2019, Used machine Year of manufacture: 2019 Rjdpewka Ntjfx Acver Equipment and technical data: Cutting height: vertical 2,150 mm, horizontal 2,070 mm Cutting length: 5,300 mm Cutting depth: 80 mm Saw blade: diameter 303 mm, bore 30 mm, Z=60 alternate top bevel teeth Saw blade speed: 5,000 rpm Motor: 5.5 kW Required air pressure: 6 bar Measurement readout for: - horizontal cuts: via scale and strip cutting stop - vertical cuts: via scale from 0 - 1,300 mm Extraction port: 100 mm 5 material support rollers per meter of cutting length 1 infeed and 1 outfeed roller Pneumatic workpiece clamping device between the support rollers 1 central support element per meter of cutting length Twist-resistant, freestanding machine frame Pneumatically retracting slatted frame Round bar guide vertical and horizontal Fine-adjustable folding stop Fine adjustment for horizontal cuts via handwheel Strip cutting stop Manual programming rail with 5 T-nuts Pneumatic plunge of the saw unit Pneumatic saw head lock Control unit at the saw assembly: start button, stop button Operator panel with template holder Electronic digital display for the saw unit Electronic digital display for the folding stop Automatically swiveling saw head Location: Flörsheim Availability: short-term

Condition: new, Year of construction: 2023, functionality: fully functional, power: 5.5 kW (7.48 HP), cutting height (max.): 204 mm, height adjustment type: electric, table height: 910 mm, cutting width at rip fence: 1,300 mm, main saw diameter: 550 mm, slide length: 3,200 mm, Equipment: motor brake, rotational speed infinitely variable, Altendorf F45 EvoDrive Year of manufacture 2023, new machine - Template holder on the terminal - Extended cutting height, saw blade up to 550 mm, cutting height 204 mm - Motor 5.5 kW (7.5 HP) VARIO (infinitely variable speed control) Rsdpevw S Hfofx Acvsr - Preparation for 2-axis scoring saw - Table top extension 840 mm - Double roller carriage length 3200 mm - Angle miter stop - CNC parallel stop 1300 mm - Front support roller

Condition: new, The ALTENDORF F 25 offers everything in a small space, what a sliding table saw must be able to do. Whether in the first own workshop, for daily use, in industrial production Rodeu R S Hcspfx Acvsr industrial production or as a powerful second machine. - The F 25 is the space-saving all-rounder that simply makes you simply makes you more productive. Materials such as wood panel materials, solid wood, wood-like materials or extruded or extruded profiles can be cut with the best precision, easy handling and outstanding cutting quality can be easily processed. The one-sided swivel saw blade also enables angled cuts. The smooth-running double roller carriage based on the Altendorf as well as the digital display of the height and tilt are standard features. A machine for beginners and professionals alike. Double roller carriage, tiltable, man. Height and swivel adjustment, Rip fence with man. Fine adjustment, angle mitre fence, Preparation for retrofitting, of a scoring unit ----- Technical data ----- Swivel range: 0 - 46 °, carriage length: 3,200 mm, Cutting width: 1,000 mm, Cutting height: 100 mm, max. saw blade Ø: 315 mm, max. saw blade projection: 104 mm, Non CE version: max. saw blade Ø: 350 mm, max. saw blade projection: 121.5 mm, Crosscut fence extendable up to: 3,450 mm, speeds: 4,200 rpm, Motor power: 4.4 kW, 5.5 HP, work table height: 880 mm - large extraction hood is optional - - new exhibition machine -

Condition: used, Year of construction: 2000, With electric height and tilt adjustment Used, excellent condition, little used Make Altendorf Type F45 Year of manufacture 2000 Machine number GS-tested Motor 4 kW Steel guides Carriage length approx. 3000 mm Cutting width approx. 1050 mm Pivoting up to 45° Prepared for scoring unit Parallelogram guard Tabletop extension Anodized aluminum parts Electric height adjustment Electric tilt adjustment Digital display: - Cutting angle Rodpfxovxlq He Acvsr - Speed Extraction connection D 120/80 mm Space required approx. 3010 mm x 1800 mm x 1500 mm Weight approx. 1000 kg Storage location 97447 Gerolzhofen, free on load, unpacked Sold in the current condition as seen, without warranty or guarantee