Used Other machinery for sale (45)

Year of construction: 2008, Condition: good (used), Hot air sterilizer, sterilizer -Manufacturer: Melag, hot air sterilizer type Sterilizer 75 Ceb E Snewha T Tsbfjgt -Interior: W/D/H 190/295/70 mm / 2 tray supports -Voltage: 230 V -Power: 690 W -Dimensions: W/D/H 310/415/H260 mm -Weight: 13.8 kg

Condition: new, -Dimensions: 2134x776x1072mm -Usable handle length: 1500 mm -Average output: 30/35 kg/h Ley Tdeu Tdaqowh Sehf -Dryer and ironer - Thick heating cylinder for better temperature stability - Chrome-plated surface for less maintenance - Ironing belts with dynamic tension at the entrance of the ironing zone for a better finish - Optimized vapour extraction system with a nozzle along the entire length of the roller behind the pressure roller. - Stainless steel remover at the laundry outlet - 1 motor fan on models with electric heating, 2 on models with gas heating. - All mechanical parts on SKF bearings - Driven by three-phase geared motor and chain. Cgsbsu Tdaqj E Snbfst - Inverter frequency converter, variable speed from 1 to 6 m/min to adapt to the humidity and type of laundry. - Well protected electrical compartment away from heated and humid areas. - Filters on all ventilation zones to minimize maintenance. - Safety thermostat, optimum manual safety and 2 emergency stop switches. - Front entry and exit - Optional reverse gear via aluminum crank handle in case the laundry is not pulled in properly

Year of construction: 2017, Condition: used, chassis construction: Steel 4.8 mm powder coated Front wheels (Ø × width): [2×] 25.4 × 6 cm - Black Rear casters (Ø × width): [2×] 10 × 5 cm - Anti-Mark Gray Size (L×W×H): 132×55×101cm Weight (without batteries): 178-201kg Weight (with 210Ah batteries): 284 - 306 kg disc dimensions: Ø 66 - [2×] 33 cm Includes jaws with rollers for wall protection: Ø 71 - [2×] 35 cm disc motor: 270 rpm [2×] 551 W Cylindrical dimensions: 63 - [2×] 15×58cm 6'' diameter brush: 73 - [2×] 15×68cm Cylindrical engine: [2×] 551W Cylindrical brush speed: 750 rpm orbital dimensions: 61×35cm orbital engine: 735W, 2,500 rpm brush print: 79 kg / 227 kg actuator power System Voltage/Amps: 24 VDC Optional battery: *Includes onboard charger 245 ah WET / 250 ah AGM* Run Time Based on continuous scrub run times: Up to 3.5 hours power: All Gear / Sealed (559W) Driving speed: 0 - 88m/min / 0 - 5km/h scrub speed: 0 - 70m/min / 0 - 4km/h reverse speed: 0 - 61 m/min / 0 - 4 km/h tank solution capacity: 79 liters – with measuring tube Solution Flow / Filter: 0 - 2 l/min tank recovery capacity: 87 liters - 1.5 inch Ø drain hose Small tank capacity: 60 liters of solution recreation: 64 liters Cjb E Ssh Dfbrsnbfjgt demisting chamber: 4.7 liters drain: 492cc vacuum performance: 588W water buoyancy / airflow: 173cm / 2cm Description: Suitable for wet cleaning of industrial floors including tiles, epoxy etc. With the perfect balance Between maneuverability and productivity, the Mini-HD simplifies and enhances your cleaning. This medium sized walk behind scrubber offers battery pack options. New price in 11/2017 was 12,000,- EURO, the machine has been serviced annually and is technically and optically in an "as new" condition. Accessories: Battery Charger

Condition: used, Year of construction: 2018, Technical specifications: Processes: Washing, rinsing, drying Power supply: 3x400 VAC +/- 5%, 50 Hz + N + PE Compressed air connection: 6 bar Power consumption: 76 kVA Cob Eewf U Rus Snbfegt Machine at a height of 1.6 m: n/a Vibrations: none Maximum payload: 200 kg Wash tank: 900 l Rinse tank: 900 l Oil separator: 200 l

Condition: used, Manufacturer: Tennant Company (USA) Model: M20 Type: Industrial Scrubber-Sweeper (combination machine) Power source: Diesel, LPG, or Battery (depending on version) Cleaning Width: Cob E Sewf E Drenbfogt - Main brushes: ~1020 mm (40 inches) - With side brushes: up to 1400 mm (55 inches) Solution Tank Capacity: 303 liters Recovery Tank Capacity: 360 liters Working Speed: ~8 km/h Approximate Weight (unloaded): ~2,177 kg Approximate Dimensions: - Length: ~2460 mm - Width: ~1220 mm - Height: ~1430 mm

Year of construction: 2024, Condition: new, Ease up your production with a Wattsan CW cleaning machine, continuous and with water-cooling. It can remove rust, paintwork, oil products, oxide coatings, welding scales, and carbon deposits from a variety of metals. This model features 1 type of cleaning seam. There are no consumables and no need for a significant amount of necessary space. Compact, portable laser cleaner that can work at any angle and in the most inaccessible places. The chiller is also built-in. The fiber length is 8 meters. The laser gun is lightweight and comfortable for long-term use. You can give our managers a call for additional details! Wattsan CW Cleaning machine characteristics: Cooling: water Ceb Eeiicgko Snbfjgt Laser power: 1000-3000 W Machine size: 880*560*1010 mm Laser source: JPT / Raycus Weight: 145 kg Virmer provides not only prime machines but also service and delivery. Our engineers and managers are ready to answer all of your questions and provide video assistance if required. Also, owners of Wattsan equipment get lifetime online support. Virmer is located in the Netherlands and works all over Europe. Virmer is Wattsan's official supplier. We provide not only laser engravers, but also metal cutters, welders, markers and cleaning machines. Wattsan is a Chinese manufacturer, which has been creating laser equipment for almost 15 years and keeps evolving with the help of its clients. Thanks to feedback Wattsan made over 50 modernizations, which made machines more reliable, precise and powerful so you could upgrade your business up to the new level. YOU CAN WRITE OR CALL US! WE WILL SELECT THE RIGHT MACHINE FOR YOUR TASK On our company you can find a wide range of machines and components: Laser Metal Cutting Machine; Laser Metal Machine, Fiber Metal Laser, Fiber Metal Laser Engraver; CNC laser machine for metal; Laser machine for wood; CNC laser machine; Laser engraving machine; Laser engraver; Laser cutting machine for plywood; Laser engraver; Laser cutting machine for metal; CNC milling machine; laser marker. Lenses; Chillers; Cooling system for machine; Chiller S&A ; IPG laser, MAX photonics, Raycus; Compressor; Rotary device; Mirror for laser machine.

Year of construction: 2004, Condition: excellent (used), Hinst continuous cleaning system Continuous washing plants of the manufacturer Hinst are designed to treat serial parts in high quantities with highest cleanliness requirements at the same time. Plant no. 04.333 Year of construction 12.2004 dimensions approx. WxDxH: 3,80 x 4,30 x 3,80m incl. - 6 baskets: basket dimensions: 48,5x48,5x H26cm      - roller conveyor 2,10x52x90cm The continuous cleaning system has already been professionally dismantled and stored at a value of 3.500 €. these are included in the purchase price Transport can be organised by us, loading volume 2 articulated lorries. Complete factory closure, large selection of storage platforms, pallet racks, shelf racks, paternosters. High-quality industrial machines, lathes, grinding machines, hand machines. Csbeg Ipp Aj E Snbfegt Further articles - new and used - you will find in our shop! International shipping costs on request!

Year of construction: 1997, Condition: excellent (used), Functionality: fully functional, - Manufacturer: Mercedes-Benz - Type: 1424 - First registration: 07/1997 - Kilometers: 153185km - Unladen weight: 12.200kg - Payload: 3.800kg - Gross vehicle weight: 16,000kg - Power: 180kw / 244PS - Gearbox 7 speed manual - Wheel formula 4x2 - 2 auxiliary drives - Power take-off 1: NMV 4/12 - Power take-off 2: NA 4/120-10c - Travel drive in work mode - Make ZF Type HZA Duodrive - Vmax: 15/min, best cleaning speed 11/min - Body/tank - Decontamination chamber: 500 liters - Water pockets: 3200 liters (reduced from 5000 to 3200 due to weight problem) - Dirty water tank: 6000 liters (A1 tank) - Cyclone separator x2 - Cleaning concentrate - Hot water treatment - 2 vacuum pumps (capacity 1650cmb/h at 460 mbar) - 2 high pressure pumps (capacity 15 l/min-280bar) - Manual suction through suction device at the rear - High-pressure lance with adjustable dosage - High-pressure front bumper pre-treatment - Next HU: 11/2025 - German vehicle - German papers - Ready for immediate use You also can have the description in another language by Email - Our service Cgebju Tuzle E Snbfst - - Export declaration-customs registration-yellow short-term license plates-red customs license plates. - Purchase of your used construction machine or commercial vehicle - we help you with financing - we offer you transportation solutions - Inspection and demonstration of the machines from Mon-Fri 9.00-17.00 (Saturday by appointment only). - - Our pool of machines is constantly changing and is always up to date on our website - - - We are also at your disposal by telephone - - Sanisa GmbH - Otto Hahn Street 13 - 35510 Butzbach - - This offer is non-binding and subject to change. - Subject to prior sale, - Errors and/or typing errors not excluded. - Sale to our AGB`s.

Condition: used, Year of construction: 2013, operating hours: 16,520 h, KMU LOFT vacuum evaporator for industrial wastewater treatment TYPE: Destimat LE400 Year of manufacture: 2013 Operating hours: 16,520 Cgob E Snbowgfgcefot Condition: Completely overhauled: Motor, compressor Defect: Does not start automatically. Valve needs to be adjusted. No problems after startup.

Year of construction: 2021, Condition: like new (used), Pure water RKA-600 reverse osmosis system RO 250/75 CP213e Newly developed glass types and sophisticated rinsing processes require a high level of process engineering expertise in water treatment. Perfectly coordinated process combinations, such as particle filtration, softening, reverse osmosis, ion exchange, ultrafiltration or electrodeionization (EDI), ensure consistently high water quality. Over and over again. Reverse osmosis - Reverse Osmosis (Reverse Osmosis System) Person with headset icon service Trade fairs & events Sheet of paper with arrow pointing down Ceb E Snjwar Exobfogt Downloads Light bulb icon Customer solutions Water treatment based on the model of nature: reverse osmosis The experts at EnviroFALK develop reverse osmosis systems, also known colloquially as reverse osmosis systems or simply RO, which are optimally adapted to the various areas of application. The desalinated water is required for industrial processes as well as for applications in hospitals, laboratories and medical technology. Graphic reverse osmosis How reverse osmosis works – RO Reverse osmosis (reverse osmosis system) is based on the effect of osmosis, which can be seen in nature, for example, in burst cherries after a summer rain. The cherry contains a concentrated solution, the cherry juice. The raindrop represents the diluted solution. The skin of the cherry now equalizes the concentrations. The solvent enters the cherry through the cherry skin, the semi-permeable membrane. The system strives to achieve a balance between the two concentrations. However, as the volume of the cherry cannot increase, the pressure rises. This pressure is the osmotic pressure. In nature, this increase in pressure causes the cherry to burst. If this effect is reversed, the result is a reverse osmosis system. Pressure is exerted on the concentrated solution in order to overcome the osmotic pressure of this solution. The solvent passes through the membrane again and all dissolved water components remain on the concentrate side. Reverse osmosis water filter (Reverse Osmosis – RO) Reverse osmosis (reverse osmosis system), also known as reverse osmosis (RO), is a membrane process that retains ions as well as particulate substances in the water. This reverses the natural process of osmosis. In reverse osmosis systems, the saline solution (e.g. softened city water) is passed under pressure through semi-permeable membranes in the form of winding elements. Only the solvent, i.e. pure water, passes through the membrane and is obtained with a very low salt content as so-called permeate. All water components are concentrated and must be discharged to the sewer with a second partial flow, the concentrate. Reverse osmosis system (RO) On a large scale, a reverse osmosis system (RO) is not operated as dead-end filtration, but as cross-flow filtration. The raw water supply is divided into a pure water – the permeate with a proportion of 75-80% and a residual salt content of approx. 2% – and a concentrate, with which all other water constituents are continuously discharged from the reverse osmosis system. Reverse osmosis is often used in ultrapure water systems for green hydrogen production. It goes without saying that EnviroFALK water treatment systems are tailored precisely to your glass washing machines, the glass to be processed and the glass throughput

Condition: good (used), Year of construction: 2003, Filter rinsing tank Filtering takes place through an internal filter unit Cgjb E Snjiw Eafsbfst - Manufacturer: Atlantik GmbH - Model: 30.701.31.15100 - operating pressure: 10 bar - filtered grain size: 6.0 µmm (micron mm) - Overall dimensions: 1050 x 1150 x 1620 mm - Capacity: 425 L - Electrical data: 250V, 5A, 50/60Hz - Year of manufacture: 2003

Year of construction: 2024, Condition: new, The Wattsan 100W is a brand-new portable laser metal cleaning machine. This model has 1 mirror and 1 seam type. Due to its air cooling system, the machine is quite small in size. It’s quiet, fast and easy to use. It is ideal for removing rust, paint, petrochemicals, oxide layers, welding scales, carbon deposits, etc. from metal items. This portable machine can also clean adhesive and galvanised materials as well as plaster and stone products. Thanks to pulse cleaning, this machine can clean thick layers of rust, paint, petroleum products, oxide films, scale and carbon deposits from metals without heating or damaging it. Cebsr Hbwks E Snbfegt You can give our managers a call for additional details! Wattsan Cleaning 100 W machine characteristics: Cooling: Air Laser power: 100 W Machine size: 750x600x680 mm Laser source: JPT Weight: 46 kg Virmer provides not only prime machines but also service and delivery. Our engineers and managers are ready to answer all of your questions and provide video assistance if required. Also, owners of Wattsan equipment get lifetime online support. Virmer is located in the Netherlands and works all over Europe. Virmer is Wattsan's official supplier. We provide not only laser engravers, but also metal cutters, welders, markers and cleaning machines. Wattsan is a Chinese manufacturer, which has been creating laser equipment for almost 15 years and keeps evolving with the help of its clients. Thanks to feedback Wattsan made over 50 modernizations, which made machines more reliable, precise and powerful so you could upgrade your business up to the new level. YOU CAN WRITE OR CALL US! WE WILL SELECT THE RIGHT MACHINE FOR YOUR TASK On our company you can find a wide range of machines and components: Laser Metal Cutting Machine; Laser Metal Machine, Fiber Metal Laser, Fiber Metal Laser Engraver; CNC laser machine for metal; Laser machine for wood; CNC laser machine; Laser engraving machine; Laser engraver; Laser cutting machine for plywood; Laser engraver; Laser cutting machine for metal; CNC milling machine; laser marker. Lenses; Chillers; Cooling system for machine; Chiller S&A ; IPG laser, MAX photonics, Raycus; Compressor; Rotary device; Mirror for laser machine.

Condition: like new (used), Year of construction: 2021, Technical Specifications: Flow Rate: Viscosity 1 cST (1°E): 35 l/min Viscosity 21 cST (3°E): 20 l/min Cjb E Sev U Apljnbfogt Viscosity 60 cST (8°E): 10 l/min Drive Power: 0.75 kW Rated Power: 2 kW Rotor Speed: 4615 rpm Rotor Diameter: 230 mm Separation Factor: 200 g Sludge Volume: 1.5 dm³ Inlet Connection: 3/4" Inlet Head: Specific Max. Solids Capacity: 6 kg Net Weight (Centrifuge), Approx.: 42 kg System Weight, Approx.: 300 kg

Year of construction: 1999, Condition: excellent (used), 2 pieces Ultrasonic Wheel Washing Machine, Performtec, BIGWHEEL 4 Wheel Washing System - second-hand- : Price per piece ex location: 12.500.-€ (net)! Manufacturer: Performtec BIGWHEEL 4 Wheel Washing Machine Year of construction/washes performed since purchase: - 2019/18,795 Cgob E Sort T I Uonbfjt - 2020/18.003 Condition: very good Available: immediately Location: Stuttgart-Feuerbach Condition: Both wheel washers were completely serviced by the manufacturer Performtec in July 2023. Summary of results: All test cases performed correctly. Product information: - Up to 4 wheels are cleaned fully automatically in parallel - Constant, excellent cleaning results - aluminum and steel wheels can be washed, optionally also with wheel covers - All common car wheels (including SUV, run-on-flat, PAX wheels etc.) - no damage to the rim paintwork due to mechanical washing components - Extremely low-maintenance and low-wear - Four preset, fully automatic cleaning programs - approx. 520 kg stainless steel guarantees a long service life Technical specifications: - Chassis: stainless steel - Width/depth/height: 1100 mm/2010 mm/2200 mm - Wheel diameter: 530-800 mm - Wheel width: 155-330 mm - Max. Wheel weight: 50 kg

Year of construction: 2019, Condition: like new (used), Functionality: fully functional, (Please tell us your offer price) Sale only within Europe, incl. Turkey Price without packaging; delivery condition: FCA (machine location) ===== Technical data see handout. All warranty rights are excluded. For the correctness of the technical data and year of construction, Ceb E Snbjq Umu Aefjgt for the completeness of accessories and tool equipment, and for compliance with all safety and environmental protection requirements specified in the accident prevention regulations. No sale to private individuals. Sales only within Europe, incl. Turkey Price without packaging; Delivery condition: FCA (machine location) ===== Technical data please see handout in attachment. German text leading language. Without any guaranty and warranty, including completeness of tools & accessories as well as environmental and safety regulations. No private sales.

Condition: new, Year of construction: 2022, Functionality: fully functional, machine/vehicle number: 220210-15201033, IONEX K_AK_MB_MB-12-F 20_50 LITER New price approx. € 7000.00 Rinse water circulation system Mixed bed Throughput: max. 100 - 600 ltr./h Submersible pump made of stainless steel Storage tank for the rinse water with float switch for pump protection Ion exchanger cartridge filled with activated carbon consisting of: Pressure vessel · Diameter: 210 mm · Total height: 520 mm · Material: GRP with PP inner liner · Connection: 3/4" Connection adapter with separate filling nozzle with built-in upper and lower water distribution Inlet and outlet connections with screw connections · Filling: activated carbon · Contents: 12l easily replaceable Ion exchanger cartridge Ion exchanger for mixed bed consisting of: Pressure vessel · Diameter: 210 mm Invoice 2022-101713 Page 3 of 7 Pos. Article no. Description Date Quantity Unit Unit price Total price Transfer 14,278.00 · Total height: 520 mm · Material: GRP with PP inner liner · Connection: 3/4" Connection adapter with separate filling nozzle with built-in upper and lower water distribution Inlet and outlet connections with screw connections · Filling: high-performance resin Cob E Snbevx Rxcefegt · Contents: 12l easily replaceable Ion exchanger cartridge Ion exchanger for mixed bed consisting of: Pressure vessel · Diameter: 210 mm · Total height: 520 mm · Material: GRP with PP inner liner · Connection: 3/4" Connection adapter with separate filling nozzle with built-in upper and lower water distribution Inlet and outlet connections with screw connections · Filling: high-performance resin · Contents: 12l easily replaceable Rotameter 100 - 1000 l/h and tap. Filter candle 10" fine filter Plastic circulation tank Bypass valve Conductivity meter with digital display and alarm output Replacement column filled with mixed bed resin Technical data Electrical connection: 230 V AC, 0.5 kW Dimensions: Width: 1100 mm Depth: 500 mm Height 1000 mm Weight: approx. 80kg 6.6 15302020 UV unit for Ionex MB 12 2022/14 1 piece 475.00 475.00 To reduce algae growth. Flow rate: max. 600 l/hr Power: 11 watts Lamp life: approx. 9000 h Number of lamps: 1 Quickly and effectively reduces harmful germs. Eliminates cloudiness caused by algae or bacteria.

Year of construction: 2017, Condition: like new (used), MMM Uniclean® PL II 15 single chamber washer-disinfector (Mint condition, year of manufacture: 2017) Product description (Source: MMM) Powerful single-chamber washer-disinfector for thorough reprocessing of large quantities of medical devices such as general surgical and MIS instruments, anesthesia materials, ophthalmic and dental surgical instruments, containers, bowls, trays, surgical shoes and other utensils. Operating convenience Loading baskets can be conveniently loaded from all four sides. Easy-Move casters: Even heavy baskets can be moved easily with little effort and positioned precisely in the chamber. Glass control panel - easy to clean Rubberized CoolTouch handles allow even hot baskets to be touched. Frame and front panel made of stainless steel 1.4301 (AISI 304) Chamber and all fixed piping in contact with the product in AISI 316L Glass doors in double glazing with securized glass Glass panel with integrated 5.7" color touch screen on loading side Large residual run indicator and door switch on the unloading side TECHNICAL DATA Model: Uniclean PL II 15-2 EL ( = Electric, not external steam) Single or double door: Double door Voltage: 380 - 400 V / 50 Hz Heating: Electric Equipment Machine Deionized water preheating tank (tank 1) Deionized water recovery tank Sound insulation machine front (tank 2) Sound insulation front of machine Sound insulation side wall Exhaust air economizer Exhaust air draft breaker Conductivity measuring system Monitoring Hepa-Filter Potential free contacts Return air locks Median connection on site Cgjb E Sneimdtvebfot Hot water connection Dosing system Suction lances 3 pieces 3. dosing pump incl. accessories Roller conveyor Semi-automatic transport Basic module Automatic roller conveyor Automatic loading roller conveyor preparation Automatic unloading roller bank preparation Batch documentation and machine connection Barcode reading system UPL II (cable) Barcode reader for basket recognition For the correctness, completeness and topicality of the data we do not take over guarantee.

Condition: new, Year of construction: 2024, The Wattsan 200W is a brand-new portable laser metal cleaning machine. Due to its air cooling system, the machine is quite small in size. It’s quiet, fast and easy to use even for a begginer. It is ideal for removing rust, paint, petrochemicals, oxide layers, welding scales, carbon deposits, etc. from metal items. This portable machine can also clean adhesive and galvanised materials as well as plaster and stone products. Thanks to pulse cleaning, this machine can clean thick layers of rust, paint, petroleum products, oxide films, scale and carbon deposits from metals without heating or damaging it. You can give our managers a call for additional details! Cgob E Sjr Hbx Tenbfot Wattsan Cleaning 200 W machine characteristics: Cooling: Air Laser power: 200 W Machine size: 750x600x680 mm Laser source: JPT Weight: 46 kg Virmer provides not only prime machines but also service and delivery. Our engineers and managers are ready to answer all of your questions and provide video assistance if required. Also, owners of Wattsan equipment get lifetime online support. Virmer is located in the Netherlands and works all over Europe. Virmer is Wattsan's official supplier. We provide not only laser engravers, but also metal cutters, welders, markers and cleaning machines. Wattsan is a Chinese manufacturer, which has been creating laser equipment for almost 15 years and keeps evolving with the help of its clients. Thanks to feedback Wattsan made over 50 modernizations, which made machines more reliable, precise and powerful so you could upgrade your business up to the new level. YOU CAN WRITE OR CALL US! WE WILL SELECT THE RIGHT MACHINE FOR YOUR TASK On our company you can find a wide range of machines and components: Laser Metal Cutting Machine; Laser Metal Machine, Fiber Metal Laser, Fiber Metal Laser Engraver; CNC laser machine for metal; Laser machine for wood; CNC laser machine; Laser engraving machine; Laser engraver; Laser cutting machine for plywood; Laser engraver; Laser cutting machine for metal; CNC milling machine; laser marker. Lenses; Chillers; Cooling system for machine; Chiller S&A ; IPG laser, MAX photonics, Raycus; Compressor; Rotary device; Mirror for laser machine.

Condition: good (used), KEN 211-OS Laboratory Dishwasher Laboratory dishwashing machine with high capacity The flexible machine for laboratories with high washing needs Csbjiu Uras E Snbfegt The KEN 211-OS covers the quality washing needs of laboratories Advantages Washing of instruments in up to 2 levels High capacity User-friendly and ergonomically correct front operation Front display with plain text Low noise level Low energy and chemical consumption for the benefit of environment and economy Minimal maintenance and service Specifications: Height 140 cm. Width 60 cm. Depth 64 cm. Electrical connection 380 Volt 3N 50 Hz Power 6,6 kW Item condition: Condition: Without plug ????? More articles - new and used - you will find in our store! International shipping costs on request!

Condition: good (used), Stock number: 2980 Manufacturer: ARIANA Year of manufacture: Cgjb Eev I A H Rs Snbfet Type: R 3000 Number: Motor power: 0.37 kW Flow rate: 550 l/h Maximum liquid temperature: 40°C Dimensions: 1,200 x 500 x 850 mm Empty weight: 83 kg

Year of construction: 2010, Condition: like new (used), 2. air cleaning plants Flow rate Max 1450 m³/h Speed 0.7 m/s Voltage 230 V, 50 Hz Dimensions L x W x H 800 x 800 x 1250 mm / system Weight: 160 kg / plant New price: €7.200,00 / PCs. Need new replacement filters and parts about us can be ordered! Cob E Sodt E Aksnbfjgt Price: €3.990,00 / PCs. plus VAT VAT Siegfried Volz machine tools Rüschebrinkstr. 151-153 D-44143 Dortmund - Wambel

Year of construction: 2023, operating hours: 10 h, Condition: excellent (used), Functionality: fully functional, laser hours: 3 h, laser power: 100 W, laser wavelength: 976 nm, year of last overhaul: 2025, machine/vehicle number: 1211, Equipment: type plate available, Handheld FANUCI Futura cleaning laser with MOPA 100W fiber source power, filter ventilation system and laser cleaning visor. 1. Components manufactured by the best manufacturers FANUCI cleaning lasers are equipped only with the highest quality components that guarantee reliability and stability of the laser cleaning process. The heart of the device is a single-module Maxphotonics or IPG fiber source. The highest precision of the cleaning process is ensured by the proprietary PRO Wobble laser head with an electric lens control system (oscillation). The PRO LaserCLEAN control system is responsible for the stability of the entire process. The continuity of production is ensured by Schneider, ABB, Weidmuller, Omron electrics and innovative PRO ChillX cooling. 2. Innovation friendly to the environment and health Laser cleaning technology is constantly being developed, which improves work safety and reduces the number of potential threats. The device is equipped with a PRO CleanAIR filter system that automatically removes fumes and dust, making the device environmentally friendly and the operator's workstation friendly. At the same time, it affects the extended service life of the consumable parts used. Cjb E Snjvzxcuobfogt 3. Highest cleaning precision The FANUCI cleaning laser is the first on the market to use the proprietary PRO Wobble head with a moving laser beam. It is characterized primarily by simple, intuitive operation, excellent quality of the obtained cleaning results, high operating speed and no post-process processing. The laser cleaning process is based on the shock wave effect. The focused laser beam removes dirt or coatings of the layer by laser ablation. The material is heated by the laser energy and evaporates or sublimates. The layer to be removed absorbs laser radiation, after which the contamination is eliminated at a depth equal to the penetration of laser radiation. Cleaning is carried out without damaging the base material or changing its geometry. High efficiency is achieved by selecting the laser wavelength. This is a very important process to obtain a faster energy flow in order to avoid damaging the surface of the material being laser cleaned. This is a fully automatic process. 4. Above-average stability and durability Laser cleaning technology ensures absolute stability and quality of the process, and also guarantees the highest precision of material cleaning. This is currently the best and most durable cleaning solution available on the market. It perfectly replaces traditional cleaning methods currently available on the market.

Year of construction: 2014, Condition: excellent (used), Professional pneumatic cleaning cabin with dust extraction. It is used in power plants, cement and gypsum factories, mills and mixing companies, also in the chemical industry As in the metallurgical industry, dust can have a very negative impact on the health of personnel. By using cleaning cabins we prevent dust and hazardous substances from being carried into toilets, changing rooms etc. The cabin provides personnel with a simple option to to clean themselves during working hours, e.g. before The cabin provides staff with a simple option to clean themselves during working hours, e.g. before and during breaks in the morning and at midday and at the end of the shift. Exhaustion made in EX version Year of manufacture : 2014 Filtration surface: 16 m2 Csb E Snbohm E S Ajfjgt Capacity: 2500m3/h Vacuum: 2400 Pa The device is in very good condition

Condition: like new (used), Year of construction: 2023, operating hours: 20 h, Functionality: fully functional, machine/vehicle number: MTVB20230110, laser power: 1,500 W, laser wavelength: 1,064 nm, working range: 50 mm, total length: 1,050 mm, total height: 1,030 mm, total width: 630 mm, overall weight: 200 kg, type of input current: DC, input current: 40 A, input voltage: 220 V, input frequency: 50 Hz, power: 8 kW (10.88 HP), compressed air connection: 1 bar, connection type: AC/DC, type of cooling: water, Equipment: cooling unit, Parameters: Laser type: CW Fiber laser (continuous laser) Laser source: Maxphotonics Laser power: 1500 W Cooling: Water circuit Power cable length: 10 m Output power: 10% - 100% according to settings Span width: 10-1700 mm Cgsb Eeucc Dge Snbfot Center wavelength: 1064 nm Autofocus: yes Mobility: yes - portable device Working temperature: 0°C - 40°C Working environment humidity: less than 80% Laser head cooling: nitrogen, argon, air Included equipment: Laser head with power cable Air hose for cooling the laser head Replaceable lenses for the laser head Manometer for cooling the laser head Set of keys with storage box Safety goggles

Condition: good (used), Operating hours, etc. see photos Csb Esmxmlie Snbfogt