Used eccentric presses single column over 100t for sale (107)

Condition: used, pressure 110 t throat 290 mm stroke 20-124 mm no. of strokes 60 / 90 Hub/min ram adjustment 85 mm Hnjdet Ei Hnepfx Apnop table surface area ca. 920 x 590 mm ram surface ca. 530 x 280 mm distance table to upper part of the press ca. 450 mm hole in the table ca. 180 x 300 mm mm table height ca. 750 mm tool hole in ram Ø 50 mm Number of working hours 8214 h distance table to upper part of the press mm weight of the machine ca. 5,5 t dimensions ca. 2000 x 2000 x 2600 mm overhauled by the manufacturer Helmerding in 2014 including conversion to new press safety control. Operating hours read since overhaul in 2014: 8214 Documentation of press safety control available electrical grease central lubrication Hydraulic clutch-brake combination Mechanical break plate in the ram two-hand operation foot control

Condition: used, Technical details: Pressure: 160 t slide stroke: 32...140 mm no. of strokes: 50 Hub/min throat: 400 mm dayligth: 400 mm adjustment of ram slide: 100 mm table-size: 1000x750 o. Aufspannplatten) mm ram surface area: 850x630 mm Hodpou N Dfhofx Apnenp tool shank hole: 400x360 mm total power requirement: 15,5 kW weight of the machine ca.: ca. 10,5 t dimension L-W-H: E-Schrank 1,06x0,6x2,0 mm dimensions L x W x H: L:2,9 x B:1,25 x H:3,3 m - single and /or continuous stroke possible - 80A; Air pressure 6kp/cm²; Oil filling approx.30 Liter - 2 clamping plates (1200x760x90mm and 1200x760x70mm faucet hole dia=300mm) - foot control or manual via hand possible - last check record was 2006 can be demonstrated under power! i.D. *

Condition: good (used), Year of construction: 1963, functionality: fully functional, Weight: 7,000 kg Hodpfx Ajzlg Tlspnjnp Pressing pressure: 180 t Spindle press machine Weingarten P 160 Manufacturer / Year of production: Weingarten A.G. / 1963 Type / Serial number: P 160 / 715/61 Electrical connection: 400 V / 10 kW Maximum stroke: 350 mm Minimum stroke: 120 mm Clamping surface: 600 x 600 mm Comment: The press is equipped with a mechanical safety system, is still in operation, and can be tested. Documentation is available.

Condition: used, Year of construction: 2018, Nominal pressing force: 4,000 kN Ram stroke, adjustable in increments: 30 ... 160 mm Ram adjustment: 180 mm Throat depth: 515 mm Strokes per minute (idle): 45 / min Option: Infinitely variable stroke rate: 10 … 60 / min Die installation height at maximum stroke, bottom dead center, and ram fully raised: 660 mm Table clamping surface (W x D): 1,700 x 1,000 mm Table height above floor: 1,005 mm Ram clamping surface (W x D): 1,100 x 800 mm Pin bore in ram: 65 mm Main motor power: 45 kW Approximate machine height: 4,325 mm Machine weight: 33,000 kg Control system – Press safety control with redundant design and self-diagnosis, featuring plain text status and error display Infinitely variable stroke rate in the range of 10 ... 60 strokes/minute via ABB frequency inverter Control variant: TFT color touchscreen including electronic cam controller with die management and die protection, with color touchscreen visualization, SIEMENS PLC S7-300, die data management, counting systems, data transmission via Profibus Fully automatic stroke adjustment / ram adjustment Rigidly welded tie rods, clear distance between tie rods: 1,345 mm Hnedpfx Aow Rbxzspnsp Swiveling main control console Non-contact safety guard – BWS brand LUMIFLEX, mounted at the front of the machine table or die area, installed on the tie rods

Condition: used, Year of construction: 1988, pressure 200 t throat 450 mm stroke 30 - 140 mm Hedpfxjvb I Itj Apnjnp table surface area 1100 x 850 mm dayligth 500 mm ram surface 800 x 600 mm ram adjustment 110 mm tool hole in ram Durchm. 65 x Tiefe 105 mm no. of strokes 45 Hub/min total power requirement 15 kW weight of the machine ca. 14,2 t dimensions of machine L x W x H 3,18 x 2,09 x 3,05 m

Condition: used, Year of construction: 1976, pressure 100 t throat 315 mm stroke 8 - 112 mm table surface area 725 x 570 mm ram surface 410 x 315 mm ram adjustment 80 mm no. of strokes 55 / 82 Hub/min tool shank hole (depth x diameter) 85 x 50 mm Hnjdpfx Aougnpiepnjp dayligth 355 mm total power requirement 7,5 kW weight of the machine ca. 6 t dimensions of machine L x W x H 2,00 x 1,00 x 2,87 m

Condition: new, neu ca. 14 - 16 Wochen ab Auf Türkei 92600 € 1750.14 € 160 to 6 mm 750 mm 1100 mm 230 mm 1 - 172 mm 45 1/min 6 100 mm 80 mm 375 mm 540 mm 11 kW 1890 mm 1950 mm 3650 mm 15500 kg Welded steel frame construction 6-fold ram guide Pneumatic clutch-brake combination Protective enclosure with light barriers and side doors Mechanical overload protection Two-hand and foot pedal operation Manual stroke adjustment Motorized ram adjustment Variable stroke rate via frequency converter Hnjdpfx Apjwiqu Rsnsp Operating modes: * Adjustment mode * Two-hand release * Foot release * 2-stroke operation via light barriers * Continuous operation Touchscreen for * Stroke counter with preselection for continuous operation * Stroke rate adjustment * Lubrication intervals and duration * Alarm messages * Motor direction of rotation * Monitoring of inputs and outputs 2 free cams for connecting peripherals Automatic central lubrication Equipment in accordance with CE regulations Symbolic photos, picture incl. optional available bolster plate OPTIONS: vibration pads € 192,00 bolster plate o.r. hydr. overload safety device o.r. etc.

Condition: used, Year of construction: 1979, Technical details: pressure: 250 t slide stroke: 40-160 mm throat: 545 mm ram adjustment: 110 mm Table dimensions: 1250x800x100 mm biggest distance between table & ram: 670 mm drawing capacity: 16 to Hnjdpeu Nfinjfx Apnep table height over floor: 1000 mm surface area of ram: 900x670x100 mm distance between columns: 500x400 mm total power requirement: 23 kW weight of the machine ca.: 16,6 t dimensions of machine: 2,8x1,4x3,7 m dimensions electric cabinet LxWxH: 1,15x0,6x2,1 m Ejector and counter holder force: 16t Table size with 4x T-slots parallel running (1250x800x100mm) Ram plate with 4x T-slots radially running Data at bottom dead center UT: largest stroke: 510mm smallest stroke: 570mm Accessories: - Steel plate 1170x860x80mm *

Condition: used, Year of construction: 1981, Technical details: pressure: 250 t slide stroke: 36...126 mm throat: 400 mm ram adjustment: 110 mm surface area of ram: 630 x 500 x 100 mm dayligth: 400 mm Table dimensions: 1000 x 750 x 100 mm table height over floor: 1000 mm total power requirement: 23,0 kW weight of the machine ca.: 13,5 t dimensions electric cabinet LxWxH: 1,1 x 0,7 x 1,3 m dimension machine xH: 3,0 x 1,3 x 3,3 m further details: - control via 2 hand control console or with foot pedal - foot plates Ø 220mm accessory: Hnodpfxou Nfkle Apnsp - column punch device *

Condition: used, Year of construction: 1983, Technical details: pressure: 100 t stroke: 20 fest mm Hedpfxsu Nfizj Apnsnp no. of strokes: 55 Hub/min throat: 355 mm mortise hole in ram: Ø 36 mm table surface area: 900x640 mm ram adjustment: 150 mm clamping surface ram: 500x415 mm height over floor: 800 mm biggest distance between table & ram: 390 mm passage opening in table: Ø 330 mm total power requirement: 11 kW weight of the machine ca.: 7,5 t dimension machine xH: 1,46x1,58x2,57 m transport dimensions LxWxH: 1,9x1,6x3,1 m Press is without electric cabinet, optional construction of electric cabinet possible. *

Condition: used, Technical details: pressure: 250 t stroke: Dauerlauf-Leerlauf 40 mm slide stroke: verst./adjust. 36 - 126 mm adjustability of Ram: 110 mm Hnedpfxou N Ddwo Apnjp clamping surface ram: 630 x 500 (lxb) mm clamping surface area: 1000 x 750 x 100 mm distance table/ram: 400- 526 mm passage opening in table: 400 x 360 mm operating pressure: 0,6 MPa MPa ejector path: 63 mm throat: 400 mm total power requirement: ca. 20,0 kW dimensions electric cabinet LxWxH: 1,2x0,65x2,1 m dimension machine xH: 2,9x1,2x3,4 m - two hand control - operation panel accessory: - foot plate 2200x1500x40mm *

Condition: used, Year of construction: 1980, Technical details: Hsdpfx Aou N A Uuopnsnp pressure: 400 t stroke: 40 - 140 mm strokes / minute continous: 32 throat: 400 mm dayligth: min/max: 450/590 mm ram adjustment: 125 mm table-size: 1250x750 mm height over floor: 1130 mm total power requirement: ca. 31,5 kW weight of the machine ca.: 23,0 t machine dimensions LxWxH: 3,7 x 1,7 x 3,9 m dimensions electric cabinet LxWxH: 1,0 x 0,7 x 2,1 m further details: - clamping plate : L x W x H : 1260 x 760 x 100mm - with draw cushion device force 250kN, travel approx. 83mm - control via panel i.D. *

Condition: used, Year of construction: 1980, Technical details: Pressure: 160 t stroke: 20-160 mm throat: 400 mm ram adjustment: 120 mm no. of strokes: 71 Hub/min daylight dimension : table/slide up: 720 (bei Hub 160mm) mm daylight dimension : table/slide low: 560 (bei Hub 160mm) mm ram surface area: 900 x 660 mm distance between columns: 500 x 450 mm table surface area: LxBxØ: 1200 x 750 x 100 mm total power requirement: ca. 23.0 kW weight of the machine ca.: ca. 15,0 t dimension machine xH: 2,7 x 1,5 x 3,45 m dimensions electric cabinet LxWxH: 2,0 x 0,65 x 2,15 m Hodju N A U Iopfx Apnonp Operation via control panel/operator stand/foot control and hand-held control unit The press can be offered with two options. 1st option: Sold as is, not connected, not complete, not functional. 2nd option: The baler will be refurbished, all parts will be exchanged, replaced and puddled. The press will be set up again. For inquiries about this press, please select your offer option! in progress. *

Condition: used, Year of construction: 1983, Technical details: pressure: 100 t stroke: 20 fest mm no. of strokes: 55 Hub/min table surface area: 900x640 mm throat: 355 mm ram adjustment: 150 mm mortise hole in ram: Ø 36 mm Hsdpju Nfi Usfx Apnonp clamping surface ram: 500x415 mm height over floor: 800 mm biggest distance between table & ram: 390 mm passage opening in table: Ø 330mm mm total power requirement: 11 kW weight of the machine ca.: 7,5 t transport dimensions LxWxH: 1,9x1,6x3,1 m Press is without electric cabinet, optional construction of electric cabinet possible. *

Condition: used, Technical details: pressure: 160 t throat: 760 mm slide stroke: 32...140 mm distance between table / ram: 400 mm ram adjustment: 100 mm no. of strokes: 50 Hub/min table:: 760x1000x95 passage opening in table: 400x350 mm clamping surface ram: 630x850 mm clamping plate: 760x1010x92 mm total power requirement: 15 kW weight of the machine ca.: 6,2 t dimension machine xH: 2,9x1,2x3,4 m dimensions electric cabinet LxWxH: 0,8x0,45x2,1 m - via two hand control - copy of documents digital available Hedeu Nfhqjpfx Apnsnp Machine can be demonstrated under power. *

Condition: used, Year of construction: 1985, Technical details: pressure: 100 t no. of strokes: 35-100 Hub/min throat: 360 mm ram adjustment: 20-130 mm ram surface area: 750x550 mm clamping plate on table: 1000x640 mm adjustment of stroke: 90 mm passage between the columns longitudinal/sideways: 610x500 / 440x550 mm daylight dimension : table/slide low: 300 mm total power requirement: 17,5 kW weight of the machine ca.: ca,7,0 t dimension machine xH: 1,9x1,4x2,7 m - there are 5 T-slots lengthwise on the ram plate - centre hole = 50mm Hedju Nfh Djpfx Apnenp This press is currently for sale without controls. Optional on customer request completion possible. i.D. *

Condition: used, Year of construction: 1980, Pressure capacity 1,250 kN Adjustable stroke 20 - 140 mm Stroke rate 70 1/min. Further data and pictures on request Hnodporm Ntpjfx Apnop the press is currently not functional and must be mechanically and electrically overhauled

Condition: used, Year of construction: 1991, Pressing force 1,500 kN Adjustable stroke 20 - 132 mm Ram adjustment max. 90 mm Stroke rate 50 / 75 strokes/min. Hodpfx Aperm Nqmsnonp Further data and images available upon request Used, the press was completely disassembled Not operational and requires mechanical and electrical overhaul Press is currently mechanically reassembled

Condition: new, neu ca. 3-6 Wochen ab Auftrag Türkei 79900 € 1510.11 € 130 to 1000 mm 640 mm 210 mm 5 - 110 mm 60 1/min 630x400 mm 90 mm 330 mm 11 kW Hjdpoynnbqsfx Apnsnp 2200 mm 1372 mm 3000 mm 8200 kg 8-fold ram guide front protection by light guard manual ram adjustment mech. overload safety device automatic lubrication user manual in GERMAN and ENGLISH according to CE rules

Condition: excellent (used), Year of construction: 1975, functionality: fully functional, throat depth: 450 mm, Very good condition! With gearbox: Capacity: 300 t Strokes: 35 spm Throat depth: 450 mm Hedjzc Rw Rjpfx Apnenp - Pneumatic clutch - Ram weight balance Ram stroke: 20 - 140 mm Ram adjustment: 80 mm Motor power: 30 HP

Condition: used, pressure 150 t Hjdpfxoyuqdhs Apnjnp Table dimensions 1000 x 360 mm voltage 400 V

Condition: good (used), Year of construction: 1997, machine/vehicle number: 0550296, Offer 26149 Technical data: - Pressing force: 125 t - Stroke: 340 mm - Table size (approx.): 1000 x 680 mm - Through-hole in table (approx.): 300 x 200 mm - Maximum installation height (approx.): 500 mm - Plunger surface (approx.): 600 x 300 mm - Dowel hole in plunger: 50 mm - Plunger adjustability: 75 mm - Stroke adjustment: 20 - 180 mm - Stroke rate: 80 1/min - Light curtain - Hydraulic clutch - Pneumatic damper Hnedey Tvdxjpfx Apnjp - Two-hand operation - Central lubrication - Separate control cabinet with operating units - Pneumatic connection: 6 bar - Drive: 400 V / 16.5 kW - Space requirement (approx.): W 1700 x H 2900 x D 2700 mm - Weight (approx.): 9400 kg

Condition: excellent (used), Year of construction: 2022, machine/vehicle number: 04H200001A220067, functionality: fully functional, power: 18.5 kW (25.15 HP), input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, pressing force: 200 t, stroke length: 400 mm, table width: 740 mm, table length: 800 mm, distance table to ram: 444 mm, clearance between the columns: 2,826 mm, overall weight: 12,500 kg, Equipment: CE marking, safety light barrier, We are offering this well-maintained Dirinler 1000C-2000 P61 eccentric press, year of manufacture 2022. Year of manufacture: 2022 Nominal pressing force: 2000 kN Hjdpfx Apoy Icnmsnsnp Distance between table and ram: 444 mm Stroke length: 25–400 mm Stroke rate: 50–70 min⁻¹ Max. ram adjustment: 102 mm Clutch-brake unit pressure: 5.5 bar Table dimensions: 800 × 740 mm Power supply: 3/N/PE 400 V 50 Hz Control voltage: 24 V Motor power: 18.5 kW Max. flywheel speed: 32 min⁻¹ Max. allowable upper tool weight: 2000 kg Machine weight: 12,500 kg Sound level: 75 dB(A) Overrun time: 182 ms Overrun distance: 52 mm Safety distance: 2826 mm Protection class: IP54 If you have any questions or require further information, please contact us via message or phone.

Condition: used, functionality: fully functional, power: 22.06 kW (29.99 HP), punching force: 250 t, EBU eccentric press suitable for inlay work, UV-tested Stroke adjustment from 10-140 mm Ram adjustment 80 mm Stroke rate 50 /min. Hodsv T Dapepfx Apnjnp

Condition: used, pressure 150 t Table dimensions 1000 x 630 mm voltage 400 V Inclineable mechanical press with Hnodpfxoyqv Ahj Apnsp updated electrics (CE2004) and bolster plates. The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team