Spindle

WEISS 174405B

Year of construction: 1984, condition: ready for operation (used), Rafamet UBB 112/2 Wheel Tread Diameter Minimum 700 mm Wheel Tread Diameter Maximum 1120 mm Clamping length 540 - 1050 mm Lhsdpfx Adehvml Ijtob Wheelset Axle Length Minimum 1640 mm Wheelset Axle Length Maximum 2800 mm Maximum Tire Width 150 mm Maximum Wheelset Weight 4000 kg Saddle Set Up Motion Speed 2000 mm/min Saddle Feed Maximum 2000 mm/min Main Drive Motor Power 80 kW Weight aprox 40000 kg

Condition: excellent (used), Year of construction: 2005, travel distance X-axis: 600 mm, travel distance Y-axis: 450 mm, travel distance Z-axis: 400 mm, rapid traverse X-axis: 35,000 m/min, rapid traverse Y-axis: 35,000 m/min, rapid traverse Z-axis: 35,000 m/min, workpiece weight (max.): 200 kg, total length: 500 mm, total width: 400 mm, table load: 200 kg, rotary table diameter: 280 mm, Coolant system Filtration tank HR 410 Handwheel iTNC530 controller 1e owner machine X - Travel: 600mm Y - Travel: 450mm Z - Travel: 400mm A - Axis: 110° B - Axis: 360° Table Length: 500mm Table Width: 400mm Table load: 200 Table Ø: 280mm Feed rate X-Axis: 35000mm/min. Feed rate Y-Axis: 35000mm/min. Feed rate Z-Axis: 35000mm/min. Feed rate A-Axis: 10Degrees/min Feed rate B-Axis: 15Degrees/min Spindle Taper: 40ISO/Bt/Mk Lsdpfxjx R S Sme Adtehb Power on spindle: 15kW Speeds / ranges: 18000Rpm ATC / revolver: 30 Coolant through spindle / Bar:20 Number of controlled axis: 5 Chip conveyor: Yes Coolantsystem: Yes Length: 3500mm Width: 3500mm Height: 2800mm Weight: 6600kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Year of construction: 2022, condition: as good as new (ex-display), Manipulator with hydraulic height adjustment, face plate with clamping slots and manual remote control. Height (face plate horizontal): approx. 532 - 1.132mm Lifting distance/lifting time (hydraulic): approx. s = 600mm, t = 20s Swivel range of face plate: approx. +-300°. Lhsdpfx Ajfw Ah Rodtob Height (Pl.-sch.vertical axis): approx. 709mm Dimensions face plate: Ø1.200mm x 40mm, 6x clamping slots Speed of the main axle: approx. 2.0 rpm (other Torque main axis of rotation: approx. 7,500 Nm Face plate speed: approx. 2.5 rpm Face plate torque: approx. 1,500 Nm

Condition: ready for operation (used), travel distance X-axis: 750 mm, travel distance Y-axis: 750 mm, travel distance Z-axis: 725 mm, Equipment: chip conveyor, documentation/manual, 4-axis machining center, year 2016, control: Siemens 840D Solution Line, NC rotary table 360 x 0.001 degrees, 2-fold pallet changer, pallet size: 500 x 630 mm, 60-fold tool changer, HSK63 tool holder, IKZ, Knoll PF 210/1750 gravity belt filter, Hyfra TKR 30 coolant temperature control, Knoll 450 K-1 scraper belt conveyor, infrared measuring probe Lodpfxjrx Sh Aj Adtohb

Condition: used, Year of construction: 2004, Pressure 630 t stroke 800 mm distance between columns 2600 mm Distance table/ram, max. stroke up, adjustment up 1500 mm Table surface area 2500 x 1300 mm Ljdpjv Svarofx Adtehb pressure of drawing cushion in table 300 t Die cushion stroke in table 300 mm Ram surface 2500 x 1300 mm Side window 1040 mm feed down 600 mm/s feed up 360 mm/s working feed 14 - 42 mm/s power requirement 145,0 kW Weight 85,0 t dimensions (WxDxH) 4,2 x 4,0 x 7,8 m height over floor 6,80 m height beneath floor 1,0 m Demonstration machine from technical university with approx. 920 operating hours! Mint condition! permitted for manual loading according to the CE-norm with oil-hydraulic drive, controllable dependent on pressure/time and way, upper and lower stroke limitation, light-guard (Sick) on front and back, hydraulic drawing cushion in table with ejector function, hydraulic cutting impact cushioning, mechanical depth stop via 4 motor-adjustable spindles, hydraulic ram interlocking, two-hand operation 2 tool changing consoles, 4 hydraulic ball roller tracks, 4 dampening elements

Condition: excellent (used), Year of construction: 2019, X-axis 5,000 mm Y-axis 3,000 mm Z-axis 1,500 mm Table size 5,000 x 2,500 mm Tool holder HSK 63 Tool changer 60 positions Control HEIDENHAIN TNC 640 Including through-spindle coolant (IKZ) 40 bar Including simultaneous fork head Lhjdox E S E Nopfx Adteb Including complete documentation Including IKZ 40 bar

Condition: used, Year of construction: 2013, turning diameter . mm turning length 2000 mm control Siemens 840 D sl mainspindle: turning speed max. 3800 1/min mainspindle: torque max. 1200 Nm diameter of quill 140 mm center point MK6 quill power 5 - 30 kN feed rate Z-axis mm/min Lhjdpfx Adevu E R Setob rapid traverse Z-axis 40 m/min feed rate X-axis - mm/min rapid traverse X-axis 25 m/min total power requirement 125 kW weight of the machine ca. 20 t The machine can still be inspected under power at the production plant. The condition of the machine is good, the accuracy during turning operation is very good. The milling drive is not functional. A quotation from Niles for the repair of the milling drive is available on request. Including hydraulic steady rest.

Year of construction: 1990, operating hours: 16,400 h, condition: good (used), AICHELIN ROTARY FURNACE WITH HESS PRESS AND WASHING MACHINE description: Rotary hearth furnace AichelinModel: RDLGs-R-SJ-1,5m. Year: 1990 External dimensions: 2460 x 2460 x 2335mm Operation: Gas fired with 4 Rekumat self-recovery radiant tube burners. Consumption electrical connection: Connection voltage 380V/50Hz Control voltage 220V/50Hz Total nominal consumption 15Kva Nominal consumption motors 11,7Kva Max. temperature: 950º Cycle time approx. 50 seconds. Hess PressModel : HP 1-48 Year : 1990 Ledpfx Adonzhx Hstehb Outside dimensions : 1830 x 1650 x 2630mm Empty Weight: 3000kg Max Cooling Unit: 230kg of SteelMax Workpiece Size: Approximately 210mm Caber Washing MachineModel: 350 T Year: 1990 Outer dimensions: 7100 x 1470 x 2700mm Unladen weight: 4000kg Loading height: 1180mm

Condition: good (used), Year of construction: 2007, control 840 D x-axis 4000 mm y-axis 3000 mm z-axis 2200 mm Technical data: The travel in the x-direction is 4000 mm, in the y-direction 3000 mm and in the z-direction 2000 mm. The quill stroke is 800 mm. The distance from the spindle center to the clamping surface is a minimum of 80 mm and a maximum of 3080 mm. The maximum workpiece weight is 20000 kg. The worktable is rectangular (HEHM) with a clamping surface 2500 mm long and 2000 mm wide. There are 12 T-slots according to DIN with a slot width of 28 mm and a slot spacing of 160 mm. The table height above floor level is 800 mm. The table can be swiveled through 360°. Ledpfx Aswzyphsdtehb The work spindle has an ISO 50 tool holder in accordance with DIN 69871-A40. The spindle diameter is 160 mm. The maximum torque absorption is 2346 Nm. The spindle cannot be swiveled.

Condition: used, Year of construction: 2005, 1 used crankshaft milling device in very good condition for mounting e.g. on a lathe for milling crankshafts or other milling work Make: SEMA, Origin Austria Model: SE 100 Year of manufacture: 2005 Technical data: Spindle holder ISO 50, concentricity / test mandrel L=300 mm = 0.01 mm Speed range, infinitely variable, currently set to 2,000 rpm Spindle is designed for up to 3,000 rpm Drive power currently 15 kW The milling spindle is designed for up to 25 kW Bearing diameter 110 mm The 2 screwed-on adapter plates under the milling spindle are each screwed on. These plates can be used for your lathe, reworked or may have to be newly manufactured. Screw-on surface of the milling spindle: L x W: 490 x 250 mm Accessories / special features: Milling spindle: - The milling spindle is mounted on the face support of your lathe - Infinitely variable speed adjustment, LENZE frequency converter, designed for up to 30 KW - Clockwise / counter-clockwise rotation - Lifetime lubricated spindle bearings - Sturdy construction with hardened and ground spindle - High precision - Spindle with 2 bearings and 5 spindle bearings - Tool tightening via a threaded spindle - Mobile carriage with control panel - Emergency stop - Lockable main switch Drive gear for the main spindle: - A long drive rod is mounted in the spindle bore and connected to the gearbox - Infinitely variable speed adjustment, LENZE frequency converter - Clockwise / counterclockwise rotation - Jog mode Fast / slow The pictures show this unit mounted on a SARO SPA 10 x 3000 universal lathe for milling crankshafts. This lathe is not included in the scope of delivery! Lodpfsddziyox Adtjhb Siegfried Volz Machine Tools Rüschebrinkstr. 151-153 D - 44143 Dortmund - Wambel