Weinig PFA 17N

Weinig PFA 17N

Condition: used, Number of boring spindles 7 St. Working width 160 mm Working height 120 mm Ljdpfx Apozb Rffomerp Length of the planing table 2.000 mm Feed motor 2,2 kW Weinig PFA 17 N (Unimat) automatic planing and chamfering machine for four-sided planing and profiling of wood, equipped with a universal spindle. Spindle 1: Bottom / 35 mm / 4 kW Spindle 2: Right / 35 mm / 3 kW Spindle 3: Left / 35 mm / 5.5 kW Spindle 4: Right / 35 mm / 7.5 kW Spindle 5: Top / 35 mm / 5.5 kW Spindle 6: Bottom / 35 mm / 4 kW Spindle 7: Universal / 35 mm / 4 kW

Condition: used, No. 3213 Thermal treatment system / vacuum dryer WTT Used, year of construction 2017 Thermal treatment system / thermal chamber for the modification of wood The WTT thermal chamber is a system for the thermal modification of wood. It enables efficient treatment of 2 to 3 batches per day, depending on the thickness and type of wood. The system has a powerful energy and heat transfer system and works with a gas or oil-fired boiler system that uses thermal oil as a heat transfer medium. Technical data: Capacity: 5950 - 9900 m³ of wood per year (for 330 working days) Usable volume: 9 m³ (with 50 mm wood thickness) Stack dimensions: 10500 x 1300 x 1100 mm LWH Minimum board thickness: 10 mm Power connection: 3 x 400 V, 50 Hz + zero + earth, 63 A Specific power consumption: 15.9 kW/m³ Maximum heat output: 2 MW (230 °C - 250 °C thermal oil) Heat consumption: 120 kWh/m³ wood Autoclave length: 11,000 mm Autoclave diameter: 1,800 mm Autoclave material: 10 mm stainless steel duplex EN 4462 Door opens hydraulically, with 1.5 kW drive Working pressure: 0.1 to 15 bar (absolute) Working temperature: 0 °C to 220 °C 200 mm glass wool insulation, clad with 1 mm galvanized sheet steel Main components: 1. autoclave, in which the heat treatment takes place 2. vacuum system that sucks the air out of the autoclave before heat is applied 3. energy center with a 2 MW oil burner 4. 4 MW cooling system with dry coolers 5. nitrogen generator 6. gas cooler system Heating and cooling system: Heat exchanger: 8 units (4 on each side) Material: Stainless steel pipes (seawater resistant) Total floor area: 165 m² Cooling water consumption: 1000 l/batch (not contaminated, only heated) Control and operation: Control system: WTT ExoT (fully automatic) 22” color monitor, IBM computer, printer Sensors: Ljdpfov Si Szjx Apmsrp 4 PT100 temperature sensors 2 mechanical thermometers 1 vacuum/pressure transmitter 1 mechanical vacuum/pressure gauge Special equipment: Hydraulic rail bridge for convenient transportation of wooden trolleys Automatic trolley extraction with cable winch (1.5 kW) 2 MW thermal oil boiler (heating) Fuel oil tank (4000 l) with measuring system Insulated 20 foot steel container for heating module Stainless steel safety chimney (300 mm diameter, 6000 mm length) Functional description: 1. filling the autoclave with wood 2. creating a pre-vacuum 3. filling with gas 4. heating 5. modifying 6. cooling 7. pressure equalization 8. creating a post-vacuum / drying 9. pressure equalization 10. emptying Certified EC Pressure Equipment Directive (PED) 97/23/EF Construction EN 13445 Sale on behalf of customer, from location near 5020 Salzburg (Austria), without dismantling, transportation and assembly Dismantling, loading and transportation by us optionally possible Subject to errors in the description and price To avoid possible misunderstandings, an on-site inspection by appointment is possible and recommended Sold as is Technical details, condition description, year of construction and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: “purchased as seen” Pictures and videos serve as examples and do not represent the actual scope of delivery Terms of payment: Prices excl. VAT, payment before collection or dispatch Terms of delivery: ex location

Year of construction: 1971, condition: used, Shaft Arrangement Lredpeigqzrofx Apmjp 1. Lower shaft – 4 kW, 2850 rpm 2. Right side shaft – 3 kW, 2850 rpm 3. Left side shaft – 3 kW, 2850 rpm 4. Right side shaft – 3 kW, 2850 rpm 5. Upper shaft – 5.5 kW, 2850 rpm 6. Lower shaft – 4 kW, 2850 rpm Dimensions: 4900 mm x 1300 mm x H 1500 mm Weight: approx. 5500 kg

Condition: used, Technical data: Lodpfsyhndrox Apmerp Max planing width: 170 mm Max planing height: 130 mm Spindle diameter: 40 mm Number of spindles: 6 Spindle sequence: bottom 4 kW right 3 kW left 5.5 kW right 5.5 kW top 5.5 kW bottom 4 kW Each spindle driven by a separate motor Number of upper steel feed rollers: 7 Number of upper rubber feed rollers: 2 Stepless feed speed adjustment – 4 kW Feed by chains Lubrication pump for worktable Pressure: 6 atm. Electric raising of the machine body Power supply: 400 V Total power: 33 kW Overall dimensions: Length: 5000 mm Width: 1300 mm Height: 1560 mm

Condition: good (used), Year of construction: 1994, 2-sided planing machine, top and bottom Ledpfx Apshuthyomorp Constant table (always the same feed height) Max. planing width: 600 mm Max. planing height: 280 mm Planer shafts with strip knives Ready for immediate use.

Condition: used, functionality: fully functional, power: 54 kW (73.42 HP), fuel type: diesel, color: white, operation weight: 7,500 kg, Year of construction: 2014, operating hours: 6,000 h, Equipment: adjustable boom, gripper hydraulics, hammer hydraulics, hydraulics, Terex TC75 Mono/Circular compact excavator Year of manufacture: 2014 6,000 hours Adjustable boom, over-bending Zero tail swing Lsdeyxbvdopfx Apmsrp 54 kW Deutz engine approx. 7,500 kg OQ 45 fully hydraulic quick coupler All hydraulic lines Steel tracks with rubber pads

Condition: like new (used), Manual profile grinder UTMA model P20 Lsdpeff H E Rofx Apmerp

Condition: used, No. 3176 Automatic planer and moulder WEINIG Hydromat 1000 Used, year of construction 2007 6 spindles: bottom-right-left-top-top-bottom Electronic feed 6 - 60 m/min Working width 80 - 150 mm Working height 23 - 65 mm Finished slat widths 4 - 15 mm Max. Max. number of slats 16 pieces Slat lengths 400 - 4000 mm 1st spindle horizontal at the bottom Brake motor 11 kW, 6000 rpm Spindle diameter 45 mm Tool flight circle 125 - 180 mm 2nd spindle vertical right Brake motor 7.5 kW, 6000 rpm Diameter 45 mm Tool flight circle 112 - 250 mm Max. Moulding depth 35 mm Axial adjustment travel 80 mm 3. spindle vertical left 7.5 kW, 6000 rpm Diameter 45 mm Tool flight circle 112 - 250 mm Max. Moulding depth 35 mm Axial adjustment travel 80 mm Pressure shoe in front of the spindle, swiveling away, pneumatic roller contact pressure 4. spindle horizontal top 15 kW, 6000 rpm, diameter 45 mm Tool flight circle 112 - 250 mm Max. Moulding depth 35 mm Axial adjustment path 45 mm Split pressure shoe in front of upper spindle, adjustable and swiveling away, pneumatic 5. horizontal top spindle as saw spindle Brake motor 37 kW, 5000 rpm Diameter 45 mm Axial adjustment travel reduced to 25 mm Tool flight circle 112 - 250 mm Max. Sawing depth 35 mm Axial adjustment path 45 mm Split pressure shoe in front of upper spindle, adjustable and swiveling away, pneumatic 6. horizontal spindle at the bottom as saw spindle Brake motor 30 kW, 5000 rpm Axial adjustment travel reduced to 25 mm Diameter 45 mm Tool flight circle 112 - 250 mm Max. Sawing depth 35 mm Axial adjustment path 45 mm All moulder spindles with high-performance bearings Electronic feed 7.5 kW Adjustment travel of the feed rollers compared to the left-hand spindle, axial 35 mm Shorter roller distance compared to the right-hand spindles Running meter counter, electric, with 2 counters Short infeed table (1.2 m) with 2 driven rollers above the table 1 driven, toothed roller in the table, lateral pressure roller Automatic waxilite pump / lubricant pump Machine with 4-roller extension, pendulum shafts extended to 200 mm 2 driven, toothed rollers in the outfeed table 2 driven, toothed rollers in the machine table Pressure beam before and after upper spindle with mechanical digital display DigiSet (digital double display) for left and top spindles Electrical height adjustment of the upper spindles and the feed Machine already dismantled and stored Ljdpfx Aeu Agh Sopmjrp Sale on behalf of customer, ex location near South Tyrol, without transportation and assembly Subject to errors in the description and price Transportation and loading by us optionally possible To avoid possible misunderstandings, an on-site inspection by appointment is possible and recommended Sold as is Technical details, condition description, year of construction and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: “purchased as seen” Images and videos serve as examples and do not represent the actual scope of delivery Terms of payment: Prices plus VAT, payment before collection or dispatch Terms of delivery: ex location

Condition: ready for operation (used), Year of construction: 1981, WEINIG Hydromat H25R, S/N 2603-624, year of manufacture 1981, with walk-in acoustic enclosure KASCHWIG – ALMOST NEW from 2017 • Short infeed table with heavy-duty 6-roller infeed 1st spindle bottom 11.0 kW 2nd spindle right 11.0 kW 3rd spindle left 11.0 kW 4th spindle top 15.0 kW 5th spindle bottom 11.0 kW 6th spindle bottom 11.0 kW • Hydraulic feed 6-60 m/min. • Feed motor 22.0 kW • 4x powered table rollers • Spindle diameter 50 mm • Automatic table lubrication • Spindles 1 + 4 + 5 + 6 with counter-bearings • Spindles 1 + 4 with straight jointer • Feed rollers 170 mm Ljdpfx Ajtkt Tpepmorp • 4 pcs. hydro planer heads 150 mm • 6 pcs. hydro planer heads 250 mm • Extraction hood above the machine

Condition: new, Year of construction: 2025, ∗JCB 26C-1 Pro Mini Excavator∗ - JCB Diesel by Kohler [18.4 kW / 25 HP] - Comfort cab with suspended fabric seat (ROPS/FOPS) - 2-speed travel drive - Radio Ljdpfx Asyfp Hcepmjrp - 300 mm rubber tracks - AUX I and AUX II (hammer/shear hydraulics) - 1,300 mm dipper arm - Full arm piston protection - LED work lights front/rear - Mirror package - Right / left armrest - SBSV for boom, arm, and dozer blade cylinder - Additional control unit - Grease gun Immediately operational, many more attachments in stock. Viewing appointments are expressly encouraged. On request, we can provide you with a leasing or financing offer from Mercedes-Benz Bank. Mr. Mihm (tel.) is happy to assist you. Further information can be found on our homepage. Subject to errors and prior sale! = Further information = Drive: Crawler tracks Please contact Tobias Ebert for further information.