Board formatting line

Weinig, Haist h22al

Condition: good (used), Morsoe miter punch, machine number 48706, in good condition, available immediately. If you are interested, we will also inform you about other machines in our house. You are welcome to visit the machine in our house by appointment. Hjdpfxoh Aka Ij Ag Ujfb

Year of construction: 2011, condition: excellent (used), This is a complete plant for house construction. Prices are listed with each item. Consisting of the following individual elements (see attached document as well): Photos will follow, they are already included in the attached document. Table 1 (Positioning and clamping of the frame structure) €34,500 - Elevating longitudinal conveyor with 3 hinge conveyors and sheathing - Pneumatic cross clamping - Connections for compressed air and electricity Table 2 (Applying the first sheathing and fastening) €25,300 Hfsdpfx Agou D Amgo Usb - Longitudinal conveyor with 3 hinge conveyors and sheathing - Pneumatic cross clamping - Connections for compressed air and electricity Intermediate conveyor 3 m long €4,600 (Parking station for multifunctional bridge) - Longitudinal conveyor with 3 hinge conveyors Table 3 (Applying the second sheathing, fastening and turning the element onto the next table) €35,650 - Longitudinal conveyor with 3 hinge conveyors and sheathing - Pneumatic cross clamping - Connections for compressed air and electricity - Hydraulic turning device Table 4 (Electrical installation and insulation) €34,500 - Cross conveyor with rollers and sheathing - Table traverse drive - Connections for compressed air and electricity - Hydraulic turning device Table 5 (Applying the first sheathing and fastening the second side) €32,775 - Longitudinal conveyor with 3 hinge conveyors - Cross conveyor with rollers - Pneumatic cross clamping - Connections for compressed air and electricity Intermediate conveyor 3 m long €4,600 (Parking station for multifunctional bridge) - Longitudinal conveyor with 3 hinge conveyors Table 6 (Applying the second sheathing and fastening) €28,750 - Longitudinal conveyor with 3 hinge conveyors - Pneumatic cross clamping - Connections for compressed air and electricity Table 7 (Erection and distribution table) €29,900 - Longitudinal conveyor with 3 hinge conveyors - Hydraulic tilting unit - Table traverse mechanism - Upper guide for holding the walls vertically Manual surface gantry with vacuum lifter on Table 2 €13,800 (Applying the first layer of sheathing) - Load capacity 85 kg with Schmalz vacuum unit - Steel substructure with low-friction rails - Travel range 12 x 5 m Manual surface gantry with vacuum lifter on Table 3 €13,800 (Applying the second layer of sheathing) - Load capacity 85 kg with Schmalz vacuum unit - Steel substructure with low-friction rails - Travel range 12 x 5 m Manual surface gantry with vacuum lifter on Table 5 €13,800 (Applying the first layer of sheathing on the second side) - Load capacity 85 kg with Schmalz vacuum unit - Steel substructure with low-friction rails - Travel range 12 x 5 m Manual surface gantry with vacuum lifter on Table 6 €13,800 (Applying the second layer of sheathing on the second side) - Load capacity 85 kg with Schmalz vacuum unit - Steel substructure with low-friction rails - Travel range 12 x 5 m Wall storage 1: 12 m long x 24 tracks €11,500 Wall storage 2: 12 m long x 20 tracks Vacuum lifter with column slewing crane €9,200 1 cross beam 2 t Abus €20,125 1 cross beam 2 t

Condition: ready for operation (used), Tilt destacking for layer separation Stacking lath separator with conveyor belt Hfedpfxeuzht Tj Ag Ueb Layer transport to the layer buffer Layer buffer with separation before feeding unit Layer patterns for the two separated timbers including transfer belts, for example to the stacking machine

Condition: excellent (used), Stehle S820 (automatic straight knife grinder). Please check in your junk mail if you do not receive a reply within 24hrs from sending your inquiry !!! Specification: • Maximum tool width 330 mm • Tool diameter planer heads (min-max knife heads) 120 - 230 mm • Grinding wheel speed 2850 / 5750 rpm • Possible to grind from 2 to 12 knives per head with index plate • Index plates included for 4,6,8,10 and 12 knife grinding. • Grinding wheel drive 1,3 kW Hfjdoq Dzkuspfx Ag Usb • Clearance angle 10 - 35° • Coolant tank 125 L • Motor coolant pump 0,28 kW • Connection values, total 2 kW Please check in your junk mail if you do not receive a reply within 24hrs from sending your inquiry !!!

Condition: new, Year of construction: 2025, WOOD SHAVINGS MACHINE KÄLIN Hobeltechnik, mod. MPC-P • Quantity of fresh shavings by hour: 3.800 Kg/hour • Measures logs box: 2.800mm x 1100mm x 1.300mm • Max. log input length: 2.650mm Hedsvk Saxspfx Ag Ujfb • 2 removables symmetrical cutterheads. Lenght 1.140mm. Each one in 3 pieces of: - Diameter: 200mm - Length: 380mm - Number of knifes: 8 - Sharpening full cutterheads, without removing knifes!! • 2 extra removables symmetrical cutterheads, for replacement during sharpening. Super fast cutterheads change patented system!! • Power of the cutting heads: 90 kW/120 HP • Feeding speed controlled by ELECTRONICAL INVERTER: 6 to 36 m/min • Automatic control of the forward-charge ratio of the machine • Power of the feed motor: 15 kW/20 HP • Control System of the material level inside the logs box, to avoid working without logs • Cabinet and control panel. Touch screem to control the machine • Motorized conveyor belt for the wood shavings. 800mm x 5.000mm • Weight: 11.000 Kg • CE

Condition: used, No. 3213 Thermal treatment system / vacuum dryer WTT Used, year of construction 2017 Thermal treatment system / thermal chamber for the modification of wood The WTT thermal chamber is a system for the thermal modification of wood. It enables efficient treatment of 2 to 3 batches per day, depending on the thickness and type of wood. The system has a powerful energy and heat transfer system and works with a gas or oil-fired boiler system that uses thermal oil as a heat transfer medium. Technical data: Capacity: 5950 - 9900 m³ of wood per year (for 330 working days) Usable volume: 9 m³ (with 50 mm wood thickness) Stack dimensions: 10500 x 1300 x 1100 mm LWH Minimum board thickness: 10 mm Power connection: 3 x 400 V, 50 Hz + zero + earth, 63 A Specific power consumption: 15.9 kW/m³ Maximum heat output: 2 MW (230 °C - 250 °C thermal oil) Heat consumption: 120 kWh/m³ wood Autoclave length: 11,000 mm Autoclave diameter: 1,800 mm Autoclave material: 10 mm stainless steel duplex EN 4462 Door opens hydraulically, with 1.5 kW drive Working pressure: 0.1 to 15 bar (absolute) Working temperature: 0 °C to 220 °C 200 mm glass wool insulation, clad with 1 mm galvanized sheet steel Main components: 1. autoclave, in which the heat treatment takes place 2. vacuum system that sucks the air out of the autoclave before heat is applied 3. energy center with a 2 MW oil burner 4. 4 MW cooling system with dry coolers 5. nitrogen generator 6. gas cooler system Heating and cooling system: Heat exchanger: 8 units (4 on each side) Material: Stainless steel pipes (seawater resistant) Total floor area: 165 m² Cooling water consumption: 1000 l/batch (not contaminated, only heated) Control and operation: Control system: WTT ExoT (fully automatic) Hfedpjv Si Szsfx Ag Ueb 22” color monitor, IBM computer, printer Sensors: 4 PT100 temperature sensors 2 mechanical thermometers 1 vacuum/pressure transmitter 1 mechanical vacuum/pressure gauge Special equipment: Hydraulic rail bridge for convenient transportation of wooden trolleys Automatic trolley extraction with cable winch (1.5 kW) 2 MW thermal oil boiler (heating) Fuel oil tank (4000 l) with measuring system Insulated 20 foot steel container for heating module Stainless steel safety chimney (300 mm diameter, 6000 mm length) Functional description: 1. filling the autoclave with wood 2. creating a pre-vacuum 3. filling with gas 4. heating 5. modifying 6. cooling 7. pressure equalization 8. creating a post-vacuum / drying 9. pressure equalization 10. emptying Certified EC Pressure Equipment Directive (PED) 97/23/EF Construction EN 13445 Sale on behalf of customer, from location near 5020 Salzburg (Austria), without dismantling, transportation and assembly Dismantling, loading and transportation by us optionally possible Subject to errors in the description and price To avoid possible misunderstandings, an on-site inspection by appointment is possible and recommended Sold as is Technical details, condition description, year of construction and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: “purchased as seen” Pictures and videos serve as examples and do not represent the actual scope of delivery Terms of payment: Prices excl. VAT, payment before collection or dispatch Terms of delivery: ex location

Condition: used, No. 3176 Automatic planer and moulder WEINIG Hydromat 1000 Used, year of construction 2007 6 spindles: bottom-right-left-top-top-bottom Electronic feed 6 - 60 m/min Working width 80 - 150 mm Working height 23 - 65 mm Finished slat widths 4 - 15 mm Max. Max. number of slats 16 pieces Slat lengths 400 - 4000 mm 1st spindle horizontal at the bottom Brake motor 11 kW, 6000 rpm Spindle diameter 45 mm Hodpfx Asu Agh Seg Ujfb Tool flight circle 125 - 180 mm 2nd spindle vertical right Brake motor 7.5 kW, 6000 rpm Diameter 45 mm Tool flight circle 112 - 250 mm Max. Moulding depth 35 mm Axial adjustment travel 80 mm 3. spindle vertical left 7.5 kW, 6000 rpm Diameter 45 mm Tool flight circle 112 - 250 mm Max. Moulding depth 35 mm Axial adjustment travel 80 mm Pressure shoe in front of the spindle, swiveling away, pneumatic roller contact pressure 4. spindle horizontal top 15 kW, 6000 rpm, diameter 45 mm Tool flight circle 112 - 250 mm Max. Moulding depth 35 mm Axial adjustment path 45 mm Split pressure shoe in front of upper spindle, adjustable and swiveling away, pneumatic 5. horizontal top spindle as saw spindle Brake motor 37 kW, 5000 rpm Diameter 45 mm Axial adjustment travel reduced to 25 mm Tool flight circle 112 - 250 mm Max. Sawing depth 35 mm Axial adjustment path 45 mm Split pressure shoe in front of upper spindle, adjustable and swiveling away, pneumatic 6. horizontal spindle at the bottom as saw spindle Brake motor 30 kW, 5000 rpm Axial adjustment travel reduced to 25 mm Diameter 45 mm Tool flight circle 112 - 250 mm Max. Sawing depth 35 mm Axial adjustment path 45 mm All moulder spindles with high-performance bearings Electronic feed 7.5 kW Adjustment travel of the feed rollers compared to the left-hand spindle, axial 35 mm Shorter roller distance compared to the right-hand spindles Running meter counter, electric, with 2 counters Short infeed table (1.2 m) with 2 driven rollers above the table 1 driven, toothed roller in the table, lateral pressure roller Automatic waxilite pump / lubricant pump Machine with 4-roller extension, pendulum shafts extended to 200 mm 2 driven, toothed rollers in the outfeed table 2 driven, toothed rollers in the machine table Pressure beam before and after upper spindle with mechanical digital display DigiSet (digital double display) for left and top spindles Electrical height adjustment of the upper spindles and the feed Machine already dismantled and stored Sale on behalf of customer, ex location near South Tyrol, without transportation and assembly Subject to errors in the description and price Transportation and loading by us optionally possible To avoid possible misunderstandings, an on-site inspection by appointment is possible and recommended Sold as is Technical details, condition description, year of construction and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: “purchased as seen” Images and videos serve as examples and do not represent the actual scope of delivery Terms of payment: Prices plus VAT, payment before collection or dispatch Terms of delivery: ex location

Condition: used, Rounding machine tool WemaProbst RHM 200 Hfedpfxov Ii Tko Ag Ueb

Condition: used, machine/vehicle number: IDC000031, Chip drying barrel Length - 14 m Width - 3.6 m Drying capacity - 10t/h Hedpsrl Ra Hofx Ag Usfb

Year of construction: 2000, condition: used, Brucks 100hp chipper Input and output conveyor belt, hopper, sieve Hsdpjlxqilefx Ag Uofb The machine is sold as is.