Wood shredder

WEIMA WL 4

Condition: refurbished (used), functionality: fully functional, overall weight: 1,300 kg, WEIMA WL 4 shredder, 18.5 kW Machine for shredding production waste from wood processing, furniture manufacturing, pallets, CLT, particleboard, rubber, and plastics. Mounted on vibration-damping legs. The machine is in fully working condition and has undergone the following repairs: 1. Bearing replacement on the shaft. 2. Complete gearbox service with replacement of 3 sets of bearings. 3. Replacement of the sliding rails of the drawer. Nedjz En Nrspfx Ac Aodb 4. New rotor knives. New stationary knives. 5. Replacement of the hydraulic pump. 6. New gearbox and hydraulic oils. 7. New hydraulic hoses. 8. New oil filter. 9. Sandblasting and powder coating of the entire machine. Technical specifications: POWER: 18.5 kW NUMBER OF SHAFTS: 1 SHAFT LENGTH (mm): 600 mm SHAFT DIAMETER (mm): 252 mm ROTATION SPEED: 90 rpm NUMBER OF KNIVES: 14/28 SCREEN SIZE: 15 mm MACHINE DIMENSIONS: 200 x 160 x 120 cm MATERIAL: wood waste FEED OPENING DIMENSIONS (mm): 600 x 800 mm WEIGHT (kg): 1300 kg

Condition: excellent (used), Year of construction: 1997, Single shaft shredder form Weima Ndedpfx Acsivptto Asb Model -WL6S Main motor -22kw

Condition: used, Year of construction: 2026, Special price - exhibition machine Technical specification WL 4 Hopper opening with log spacer 600 x 1,050 mm Hopper content 0.6 m³ Working width of the rotor 600 mm Diameter of the rotor 252 mm Drive power 18.5 kW Rotor speed 80 -120 rpm Number of knives 28 Type and size of knives concave / 40 x 40 mm, cutting reversible crowns Screen perforation 15-20 mm Painting WEIMA Standard RAL 2002 / 7016 Connected load 400 V +/- 5% / 50 Hz Weight approx. 1,300 kg Including: • Control cabinet* (Rittal) including electrical control (Moeller / Siemens) and star-delta start-up • Rubber vibration elements • V - rotor (patented) with knife pockets milled into the profile • Gear limit switch • Slider cycle • Slider half back • Log spacer hopper • 2. Knife series Ndsdpez A H Saefx Ac Aeb Storage location: Supplier

Condition: repair required (used), Year of construction: 1995, functionality: not functional, machine/vehicle number: 950/2507, fuel type: electric, Shredder, requires repair, possibly with a defective shaft. The device must be picked up. Nodpfx Aez Dt Uwjc Asdb

Condition: ready for operation (used), functionality: fully functional, LINDNER wood chipper for sawmill offcuts, model T 400/140-2 – after technical inspection – in very good condition – suitable for producing technological wood chips TECHNICAL SPECIFICATIONS: infeed width: 400 mm infeed height: 140 mm rotor diameter: 450 mm rotor length: 400 mm main motor power: 33 kW infeed motors power: 2 x 1.5 kW number of knives: 2 pieces screen dimensions: 60 mm x 90 mm Nodpfjr Ak Rgox Ac Ajdb infeed rollers in very good condition feeder motor power: 1.5 kW feeder length: 4,200 mm transport dimensions (L/W/H): 430 / 240 / 150 cm weight: approx. 2,000 kg

Condition: good (used), Year of construction: 2010, Engine size : 18,5 Kw Opening : 600 x 1000 mm Number of knives : 28 trapez knives Rotor diameter : Ø 250 mm Ndsdpfjz Dn Ufex Ac Asb Rotor length : 600 mm Rotor rpm : 90/min Siewe holes : Ø 15 mm Dust extraction nozzle : Ø 160 mm Can be examined in working condition, ask for WHATSAPP demo. Mounted with new knives + counter knive Weight : 1300 Kg

Condition: like new (used), Year of construction: 2016, functionality: fully functional, From year 2016 but has never been in use. As new. The machine has never been used in production. We have only tested it for a short period of time. Data: Opening: 600X1.050 mm. Rotorlenght: 600 m. V-rotor with 28 reversible knifes. Motor: 18,5 kW. 400V, 50 hz. RPM: pp. 100. Weight: 1300 kg. Ndedpfx Acjz Dg Iqs Aob Lenght/width/height: 2.045X1.165X1.640 mm. Original manual included. WEIMA - Made in Germany. Screen not included. Available in 10/12 mm 15/20 mm 20/25 mm 30/35 mm ect. Ask for quote. Very good for wood, plastic, composite ect. IN STOCK. We ship all over Europe.

Condition: excellent (used), Year of construction: 1985, still very nice veneer saw with planing head cutting length 3050 mm with rear support and fence Noden An A Topfx Ac Aodb

Condition: excellent (used), 18.5 kW 1500 kg Ndsdjz Ak Dpopfx Ac Aeb In very good condition.

Condition: excellent (used), Year of construction: 2003, Wood chipper Manufacturer: Weima Type: WL 4 Year of manufacture: 2003 Operating hours: approx. 1,244 h Power: 18.5 kW Hopper: 600 x 800 mm Rotor diameter: 252 mm Screen diameter: 15 mm Number of knives: 14 Rotational speed: 90 rpm Weight: 1,300 kg Ndsdpfxez Ai N Re Ac Aob

Condition: used, Year of construction: 2026, Special price – demonstration machine, Garbsen. Our WL 6 machine concept. The Weima high-performance shredder, with its flexible application options, can process all types of wood-based materials (hardwood, softwood, chipboard, MDF materials, plywood, veneer remnants, etc.) into wood chips, achieving a significant volume reduction of the material, especially with bulky materials. Mode of operation: The machine is equipped with a large feed hopper and can be loaded via a conveyor belt or manually. This hopper can be adapted to individual needs and guarantees a continuous and cost-effective material feed without requiring manual assistance. The hydraulically controlled slide feeds the wood waste to be shredded to the cutting area of the rotor and is automatically and load-dependent controlled. The internal slide guides are made of highly abrasion-resistant plastic (polyamide) and can be adjusted. The hydraulic cylinders are cardanically suspended to avoid transverse forces on the piston seals. The patented and profiled V-rotor, made of solid steel, has a diameter of 252 mm and operates with a rotor speed of 80 - 120 rpm. The concave, aggressive, and four-way rotatable knives/cutting crowns are located in milled knife pockets on special knife carriers. This patented system guarantees, through the resulting reduction in the cutting gap between the counter-knife and the rotor, a high throughput, low energy consumption, and an optimal discharge of the shredded material. The screen located under the rotor determines the chip size (10 - 100 mm). An optionally available, hydraulically opening screen basket is also available. The power transmission from the electric motors is via V-belts to a heavily dimensioned gearbox, which is attached to the rotor shaft on one side. Precise cutting at high throughput with a profiled V-rotor. The V-rotor, developed specifically by WEIMA, is universally applicable and made of solid material. Its aggressive material feed, with up to two knife rows, guarantees a high throughput with low power consumption. It can be equipped with hardened cutting knives made of steel with edge lengths of 30 mm and 40 mm. These can be repeatedly rotated when worn, which drastically reduces maintenance costs. Intuitive operation thanks to a Siemens PLC control with a touch display. To ensure that the electronics are optimally matched to the machine, we design, build, and wire our control cabinets ourselves. In doing so, we use only high-quality components – for example, from Siemens or Rittal. Intuitively operable touch screens guarantee quick adjustments. Functions such as adjusting the slide timing or stop ensure a high throughput. The built-in overload protection also prevents damage to the machine. Technical specifications WL 6: Feed opening 800 x 1,250 mm. Hopper capacity 0.9 m³. Rotor length 800 mm. Rotor diameter 256 mm. Drive power 22 kW. Rotor speed 90 rpm. Max. number of knives 42 pieces. Type and size of knives: concave / 40 x 40 mm, cutting crowns. Screen size 10-60 mm. Paint: WEIMA standard RAL 2022 / 7016. Connection value 400 V +/- 5% / 50 Hz. Weight approx. 1,600 kg. Including: - Control cabinet* (Rittal) incl. electrical control (Moeller / Siemens) and S Nedey D E Tdopfx Ac Asdb

Condition: used, Year of construction: 1999, functionality: fully functional, fuel type: electric, - German-made - Year of manufacture: 1999 TECHNICAL SPECIFICATIONS: - feed opening: 600 x 800 mm - rotor diameter: 175 mm - rotor length: 600 mm - total power: 18.5 kW - number of knives: 14 pcs - reversible cutting knives: 30 mm x 30 mm Nedpjw H Rn Eofx Ac Asdb - screen: Ø 15 and 12 mm - AUTOREVERSE - HYDRAULIC RAM - pressing ram height: 180 mm - rotor speed: 80–120 rpm - extraction nozzle diameter: Ø 200 mm - dimensions (L/W/H): 200 x 120 x 160 cm - weight: 1200 kg

Condition: as good as new (ex-display), Year of construction: 2026, Low-noise and low-speed model WL 4/18.5 kW Technical data: Hopper opening: 600 x 800 mm Hopper opening with log spacer: 600 x 1050 mm Hopper capacity: approx. 0.6 m³ Working width of the rotor: 600 mm Diameter of the rotor: 252 mm Number of knives: 28 pieces Knives: 40 x 40 mm, concave Screen perforation: 15/20 mm Included: Control cabinet Electrical control system Star-delta starter Ndodpfx Acjbtnfto Asb Rubber vibration dampers 2nd knife row Log spacer (self-cleaning hopper) Top-of-the-line equipment Location: In stock in Bitburg - immediately available - at a special price.

Condition: used, Year of construction: 2009, functionality: fully functional, Machines connected in one line (all three machines are only sold together). 1. Veneer crossfeed splicing machine Fisher+Rueckle FZR-15, year 2009 2. Direct Stacking Device Fisher+Rueckle DAR-22, year 2009 3. Scissor lifting table 1000 kg TECHNICAL DOCUMENTATION (full on request) Veneer Cross-feed Splicing Machine FURNIMASTER FZR-15 Veneer format length (longitudinal to the fibre) 350 - 1500 mm Veneer format width (transverse to the fibre) 50 - 500 mm Veneer strip thickness 0.3 - 1.5 mm Max machine output 30 cycles/min. (the output rates are related to an average veneer strip width of 100 mm transversely to the fibre) Connected load (basic machine): Power rate 13.5 kW Compressed air pressure 6 bar Power consumption: Ndodet Akcfjpfx Ac Asb Electric power 6.2 kWh Compressed air supply 15 NL/min. Dimensions and weight (basic machine): 2940 mm L x 1000 mm W x 1530 mm H. 3200 kg

Condition: as good as new (ex-display), Year of construction: 2026, Low-noise and slow-speed model WL 4/18.5 kW Technical data: Hopper opening: 600 x 800 mm Hopper opening with log spacer: 600 x 1050 mm Hopper capacity: approx. 0.6 m³ Working width of the rotor: 600 mm Diameter of the rotor: 252 mm Ndjdobunq Hepfx Ac Aob Number of knives: 28 pieces Knives: 40 x 40 mm, concave Screen hole size: 15/20 mm Included: Control cabinet Electrical control system Star-delta starter Rubber vibration dampers 2nd knife row Log spacer (free-cutting hopper) Location: 54634 Bitburg Available immediately