Sandblasting unit

TOSCA TS-500

Condition: refurbished (used), SCHLATTER Welded wire mesh production line MG24 Full revamped WORKING RANGE Panel width: max. 2500 mm Weft wire length: min. 900 mm Weft wire length with QF5 dispenser: min. 300 - 1600 mm Spacing between extreme warp wires: max. 2400 mm Mesh length (warp wire length): max. 2500 - 6000 mm Spacing between warp wires: min. 100 mm Spacing between weft wires: 25-250 mm Adjustable by cutting device (0-1) Warp wire diameter: 4.0 - 12.0 mm Nsdpowu Tu Dsfx Agnjwc Weft wire diameter: 4.0 - 12.0 mm Number of warp wires: max. 24 WELDING MESH MACHINE MG 24.1/8C, Basic equipment including: - 1 Machine frame - 1 Upper support for press reception, continuously adjustable by hand crank - 1 Magnet supports with retaining magnets and weft wire monitoring. - 1 Row of pneumatic solenoid valves for press actuation. - 1 Installation for air and water. - 2 Pneumatic rotary drives with oil damping - Static motor torque with 5 bar compressed air: 480 Nm - Front continuously adjustable from: 25 - 250 mm adjustable by cutting device (0-1) - 1 Advance carriage with panel lifting device - 1 Set of tools for machine adjustment WELDING SECTION 8 Type C Transformers Rated power of each transformer: 100 kVA No-load secondary voltage: 7.1 V Rated secondary current: 14 kA 8 Thyristor contactors ES 130 12 Welding presses: 5.0 kN 12 Chain current bridge for spacing of warp wires: 50-100 mm 12 Chain current bridge for spacing of warp wires (for offset warp wires): 100 mm 10 Chain current bridge for spacing of warp wires: 100-150 mm 8 Chain current bridge for spacing of warp wires (for offset warp wires): 150 mm 6 Chain current bridge for spacing of warp wires: 150 - 200 mm 6 Chain current bridge for spacing of warp wires (for offset warp wires): 200 mm 24 Lower electrode holders Cu with standard angled electrodes and each with a water-cooled current cable, width: 58 mm 24 Wire clamping pliers Panel width: max. 2500 mm Weft wire length: min. 900 mm Weft wire length with QF5 dispenser: min. 300 - 1600 mm Spacing between extreme warp wires: max. 2400 mm Mesh length (warp wire length): max. 2500 - 6000 mm Spacing between warp wires: min. 100 mm Spacing between weft wires: 25-250 mm Warp wire diameter: 4.0 - 12.0 mm Weft wire diameter: 4.0 - 12.0 mm Number of warp wires: max. 24

Year of construction: 2020, condition: new, Touch control ROMER cabins are equipped with 4 "color touch displays. Operation of the cabin is intuitive, takes place in 3 modes, automatic (time), automatic (based on a clogged filter sensor), or manual Filter clogging sensor A sensor is installed in the cabins, which queues the filters for cleaning when they become clogged. The system also informs you when the filters have worn out Automatic filter cleaning The electronic system for automatic filter cleaning has a range of cleaning frequency and shot time adjustment. Each of the filters is cleaned separately, the filters can also be cleaned manually using the buttons. We know from experience that it is difficult for the operator to enforce filter cleaning. Thanks to this system, the operator will not have to think about it anymore. Low volume Aluminum fans are very quiet, they work at the level of 74-79dB - It's not much. with the standard cabin structure, it's even hard to talk. Broaching machine through the cabin By dragging the suspension beams within the cabin, the cabin improves work efficiency, thus relieving the painter who no longer has to move them by hand. Explosion-proof design Nwedpfx Agsfzktzsnoc The booths are designed to prevent the formation of an explosive mixture during the painting process. Each of the components has been carefully selected to minimize this risk.

Condition: like new (used), Year of construction: 2017, max. wheel diameter 100 mm gear width 26 mm max. module 31 min. module 0,1 Control Siemens 840 D SL Number of working hours 9598 h total power requirement 45 kW weight of the machine ca. 7 t dimensions of the machine ca. 4x3x2,5 m Gleason 100S gear shaping machine for the production of internally and externally toothed cylindrical gears and other cylindrical workpiece circumference regularly occurring profiles and moulds as well as for the production of profiles using the single part process. Technical data: Nominal workpiece diameter 100 mm Largest circumferential diameter 150 mm Machine nominal module approx. 3 mm (Guide value depending on the respective machining task.) Shaping spindle stroke speed range 0 - 3,000 1/min Stroke position adjustment range (manual) 20 mm Largest toothing width 26 mm Smallest pitch height of the hydrostatic Nwedpfsv Ehbbsx Agnec inclined guide 400 mm Smallest/largest distance between tool axis - 20/+ 180 mm and workpiece axis Stand inclination range (manual) - 1/+ 11° Tool holder (manual clamping) HSK-D63 (hollow shank taper according to DIN 69063) Weight of the machine approx. 7,000 kg with robot cell

Condition: excellent (used), IMM 72780 Double-sided polishing machine Mint condition, the machine has hardly been used. TECHNICAL DATA Polishing wheel: 100 - 500 mm shafts: 35 mm Nsdpfx Asu Hanyognswc Spindle speed: 1500 rpm Voltage: 400 V, 50 Hz Weight of basic machine: Approx. 400 kg No responsibility is taken for the correctness, completeness and up-to-dateness of the information.

Condition: used, Year of construction: 2022, machine/vehicle number: 8525-6-9605-FA, Equipment: documentation/manual, type plate available, Hexagon Absolute Arm with 6 axes (S/N: 8525-6-9605-FA; Year of manufacture: 05.09.2022) incl. Nwedpfxowzkmkj Agnsc - CPW-5076-FA (Control Pack Wireless) - MAGNETIC BASE - Calibration bar - Certified Sphere (calibration sphere) - Standard probe set

Year of construction: 2007, condition: ready for operation (used), An Amada CNC turret punching machine for medium format sheets including an MP300 M loading unit, Wilson X-Sharp grinding machine and numerous standard and special punching tools are available. 1) CNC turret punching machine Amada, year of manufacture: 2007, punching force: 300kN, max. sheet dimensions X/Y: 3000mm/1500mm, max. sheet thickness: 6.35mm, stroke rate: 600 strokes/min, simultaneous positioning speed: 128m/min, repeat accuracy: +/-0.1mm, machine dimensions X/Y/Z: approx. 5100mm/3200mm/2300mm, weight: approx. 18000kg. 2) Automatic sheet loading and unloading system Amada MP 300 M, max. sheet dimensions X/Y: 3000mm/1500mm, min. sheet dimensions X/Y: 1000mm/300mm, sheet thickness range: 0.8mm-6mm, max. load capacity per pallet: 3000kg, max. stacking height: 400mm, max. sheet weight: 170kg, max. pallets: 9, pallet change time: 25s, sheet loading time: 18s, weight: approx. 4900kg. 3) Wilson X-Sharp tool grinding machine. Documentation available. On-site inspection is possible. Nedpfx Agjwhp N Donjwc

Year of construction: 2010, condition: excellent (used), Chamber inside 2000 x 1250 x 1250 mm Volume inside 2344 Liter Up to 400 Gr/C (Power 33kW)   Preheating / Drying For manual, cycle and CNC processing up to interactive contour programmingCovered guidance tracks (DGP) for high long-term precisionDirect drive from motor to main spindle for high running smoothnessOil recirculating lubrication unit with filtering for the lubrication of the precision main spindle bearingCombination control unit for economically advantageous programming and machine operation, as well as optimum access to the work area Nwsdpfx Agouqkwfsnoc Length:2500mm Width:2015mm Height:2900mm Weight:4000kg

Year of construction: 2004, condition: good (used), machine/vehicle number: UP 20_LIND, Used Motoman HP20 Nwedpfxefd Drrs Agnoc Type: HP 20 Control system: NX100 Year of construction: 2004.09 Load capacity: 20 kg

Condition: new, Year of construction: 2025, functionality: fully functional, total height: 5,850 mm, total length: 12,125 mm, total width: 5,150 mm, overall weight: 8,000 kg, warranty duration: 12 months, inner dimension height: 5,000 mm, inner dimension length: 12,000 mm, inner dimension width: 5,000 mm, Equipment: cabin, lighting, PAINT BOOTH 12x5x5M EZ Series Model: - LED ceiling lighting - LED side lighting - RIELLO oil burner - Four fans, including: ‎ ㅤ- 2x supply fans ‎ ㅤ- 2x exhaust fans TECHNICAL PARAMETERS: - External dimensions: 12125x5150x5850 mm - Internal dimensions: 12000x5000x5000 mm - Entrance doors: 4000x4800 mm (2 units, four leaves, reinforced hinges) - An additional BOX 1650 mm x 8000 mm should be included in dimensions – can be placed on either the right or left side. - Structure: galvanized steel frame - Heat exchanger: high-grade stainless steel - Panels: filled with mineral wool insulation Nodpfexm U Exsx Agnswc - Drive-on ramps – 2 units - Fully grated floor The reinforced frame construction prevents vibration and the air surge effect from the main supply duct. Double Roof Design: - Upper outer layer - Inner truss structure with V600 ceiling filter Air Circulation System: - Supply system: Jet turbine 7.5 kW – 2 units - Exhaust system: Jet turbine 7.5 kW – 2 units Air Filtration System: - Pre-filter collects particles larger than 10 μm - Ceiling filter collects particles larger than 5 μm - Floor filter: Paint Stop - Carbon filter Lighting: - Ceiling lights: 52 LED tubes (14 angled fixtures with 4 tubes each) - Side lighting: 26 LED panels integrated into the right, left, and rear walls Burner: Riello – 2 units, oil model 40 G20, approx. 200,000 Kcal/h - Heat exchanger: high-quality stainless steel - Heating time: 8–15 min (max. 80°C) Optional Features: - Roof-mounted boxes - Insulated roof - Pass-through doors - Water curtain - Color according to RAL palette - Explosion-proof (EX) version available

Condition: new, functionality: fully functional, Year of construction: 2025, Box Type Electrostatic Powder Coating Oven: Length: 500cm, Width: 250cm, Height: 300cm Nwodpfov Nvndjx Agnsc - Powder Coating Booth with Filter: Length:300cm, Width:220cm, Height:270cm - Electrostatic Powder Coating Equipment: Model: HMK MULTICOLOR, Type of Use: Manual