Bandsaw - Horizontal

BERG & SCHMID K-tech DG 62/45 HA-I

Condition: new, 900 mm 900 mm 900x900 mm Dedpfefg E Hpjx Afnskh saw band length 9300 x 67 x 1,1 mm table height 790 mm band speed 14 - 60 m/min total power requirement 11 kW weight of the machine ca. 8,45 t dimensions 4,485 x 1,68 x 3,15 m The semi-automatic, hydraulic saws from the X-tech line offer the best Saw technology and best performance when cutting special steels • The electro-welded machine frame and the steel saw frame meet requirements all cutting needs and eliminate vibration and noise. • The chip conveyor is hydraulically driven and the speed is adjustable • All movements of the machine (saw frame, vice, feed, Saw band guides) are carried out thanks to modern linear guides with high static and dynamic load performance, which also has very low sliding friction to guarantee. • Another characteristic feature is the roles for the Positioning of the material by a hydraulic motor are driven. They move at right angles to the material, and thus allowing optimal clamping of the material. • Thanks to the height control of the saw band position, the operator can place the band in place near the top edge of the material. After the cut is finished, the tape automatically raised back to the previous position. Alternatively you can also “Remain” can be selected in the lower position. During the The software compares the cutting load with the cutting cycle Default. This means that the sawing system can be stopped in the event of irregularities become. • The saw band is cleaned by two adjustable steel brushes. The drive takes place hydraulically. • The hydraulic unit including filter and pressure gauge guarantees one particularly quiet operation at constant pressure. • Finely ground carbide inserts that clamp the saw blade, complete with lateral, hardened and adjustable guide rollers. The adjustable one The tape guide automatically moves as close as possible to the material. • The saw band is tensioned via a hydraulic cylinder, which is carried out by the Machine software is controlled. The voltage is set according to a given Time automatically delimbed when the machine is idle or after a cycle has been carried out. • Automatic version with CNC control in the X-TECH 900 / 1200 models a feed length of 500 mm for the series for high production rates. • The material is carried by a table with seven rollers. These will driven by a hydraulic orbital motor through which the material can be placed precisely even under maximum load. • All guided movements are carried out by four recirculating ball guides with one high capacity for static and dynamic loading; strong reduced feed friction. Tempered and ground prismatic Guides. Price on request.

Condition: new, saw blade diameter 370 mm capacity 90 degrees: round 120 mm capacity 90 degrees: square 100 mm 180x100 mm Working height 925 mm saw blade turning speeds 17 - 70 U/min total power requirement 3,0 kW weight of the machine ca. t dimensions of the machine ca. 1,9 x 1,45 x 2,1 m SPECIAL PRICE!!! High-performance vertical circular saw Hydropneumatic fully automatic. (20195) · miter left 60° + right 45° · Hydro-pneumatic control of the saw unit · Electro-pneumatic material feed unit · Smooth-running, powerful worm drive with large Transmission ratio, integrated in a stable cast housing for Achieving optimal cutting results Dodpfxod Iin Ee Afnekh · Vice with double clamping arm for low-burr cuts Lateral quick shift when changing the miter · Precision prism guide of the gear head, laterally adjustable · Particularly stable base frame with built-in automatic cooling system · Large chip drawer · Chip removal brush in the saw blade protective hood CNC control: · With button for over 90 different sawing programs with 99 sub-programs for length, quantity and angle · Automatic feed unit 2,000 mm via ball screw Incremental feed with automatic length compensation. Adjustable for cutting lengths from 25 - 9,999 mm. · Fully hydraulic control of saw frame and clamping devices · Pre-selection of 3 different material feed speeds · Visualization of the entire workflow with simple data entry ATTENTION: Price is without saw blade!!! (saw blade price EUR 204)

Year of construction: 1987, condition: ready for operation (used), Center width: 400-800mm, rotational speed: 1000-2700/min, workpiece diameter: 10-300mm, grinding wheel diameter: 40-300mm, swivel angle: -45 to 45°, length: 3000mm, width: 2500mm, height: 2275mm, with oil mist separation system Hoffmann (new filter inserts), filter system gravity belt filter Faudi, hydraulic unit, additional grinding head for grinding worm gears, grinding mandrels diameter 50, 40, 27, 22, holder for SK40 and MK5, driver sets for different clamping diameters, operating instructions, circuit diagrams in paper form, an inspection is possible. Dedpfx Aergahxofnekh

Condition: new, turning diameter over bed 410 mm turning diameter over slide rest 240 mm turning length 1000 mm turning diameter in the gap 530 mm turning speeds 65 - 1810 U/min Dedpom Rlb Njfx Afnskh centre height 205 mm spindle bore 52 mm tailstock quill taper MT 4 total power requirement 2,2 kW weight of the machine ca. 0,9 t dimensions of the machine ca. 1,9 x 0,8 x 1,3 m Center lathe with: 3-axis digital measuring system fully assembled electromagnetic main spindle brake auto. Feed in longitudinal and transverse direction safety relay Micrometer end stop coolant device 3-jaw lathe chuck with 1 set of turning and drilling jaws German operating instructions.

Condition: new, capacity 90 degrees: round 350 mm capacity 90 degrees: square 330 mm 500 x 310 band speed 15 - 100 m/min table height 844 mm dimensions of saw-band 4250 x 34 x 1,1 mm total power requirement 2,2 kW weight of the machine ca. 1,2 t dimensions of the machine ca. 1,4 x 2,4 x 1,935 m ACTION PRICE!!! 2-column double miter band saw K-tech DG 50/33 HA-I • 2-column miter saw • Solid, yet easy to use • Material height sensor (automatic cut start detection) • Smooth running thanks to bevel cut, feed controller + cutting pressure controller Dkodpofg E Hlofx Afnsh • Massive material infeed roller • Removable chip tray (disinfection) • Energy-saving and low-vibration thanks to bevel cut • Ergonomic, safe and free-standing control panel • Frequency-controlled saw drive 15 -100 m/min. • Hydraulic cutting pressure control valve • Hydraulic control of saw frame and vice • LEDs for monitoring all safety functions • Large dimensioned wheels (520 mm) a. • Clear miter setting up to 60° Semi-automatic function: 1. Clamp material 2. Saw starts 3. Rapid lowering to the start of the material or the same for series cutting cut 4. Saw band off 5. Raise the frame to just above the material 6. Open the vise

Condition: new, Best price 4499 Eur (EXW Jonava, Lithuania) Dimension of sliding table- 2200x375mm Gross cut capacity- 1500mm Width of cut between saw blade and rip fence - 1140mm Saw blade diameter - 400mm Dkjdpfx Asdnxydsfnjh Height of cut (90°) - 115mm Height of cut (45°)- 105mm Speed of main saw spindle - 4500/6000rpm Main spindle diameter - 30mm Tilting saw blade - 0-45º Saws lifting, up and down, electrical control. Main motor - 5,5 kW Scoring saw blade diameter - 120mm Speed of scoring saw blade - 7000-8000rpm Scoring saw diameter - 20mm Scoring motor - 1,1 kW Weight: 700 kg * Using the blade 400mm, the smaller should be removed. Reduced saw blade should be used with not more than 350 mm main shield.

Condition: used, Equipment: soot filter, - Steering wheel&nbsp,- Shovel&nbsp, Djdpfjv I Ndcox Afnokh

Year of construction: 2009, condition: good (used), Load capacity: 30 t Dsdjqiz N Ropfx Afnskh Fine lift Lifting height 9 meters

Condition: new, Comparable to Behringer, Kaltenbach, Kasto, Jaespa, etc. Cutting range 90° Round: 260 mm Flat: 300 x 260 mm Smallest diameter: 5 mm NC-controlled, automatic material feed with hydraulic full-stroke material clamping Easy operation via NC control with plain text display Material advance function without reclamping for short section cuts Robust, linear-guided feed gripper with servo positioning for maximum precision Dedpfxjh Tnd As Afnekh Automatic adjustment of blade guides to material width Recommended options: Powered chip brush synchronized with blade speed Separate control panel 7" CE panel, network-compatible, up to 1000 data sets storable, history memory for various functions and data, etc.

Year of construction: 1955, condition: used, Radial drilling machine, drilling machine, boom drilling machine Dsdpfsd Enr Isx Afnjkh -Outreach: 2055 mm -Max. Distance from machine table to spindle mount: 1700 mm -Cone mount: MK5 -Motor power: 7.5 kW -Speeds: 11.2-1400 rpm -Columns: Ø 450 mm -Spindle stroke: 540 mm -Thread cutting device -automatic feed: 0.037-2.0 mm/rev -Clamping area: 920 x 1600 mm -Dimensions: 2580/1110/H3450 mm -Weight: 6465 kg