Condition: as good as new (ex-display), Year of construction: 2024, Cantilever rack in painted version (RAL 7016 anthracite): Scope of delivery: 4 shelf uprights height 4,200 mm with base section 1,200 mm usable depth 12 cantilever arms with 1,200 mm usable depth Longitudinal and diagonal braces for 1,300 mm upright center distance (4,000 mm shelf length) Fastening material (screws, nuts and washers) - (*Delivery or collection in approx. 1 - 2 weeks) - (*No damage to paintwork!) - (*No damaged components!) - (*Replacement parts can be reordered and extended at any time) - (*Offer available in larger quantities: approx. 50 stands in stock) Net price: € 1,990.00 plus VAT. Detailed description: - Sturdy steel construction made of IPE profiles (screw system) Dedpemhhypefx Ag Dekk - Surface painted in RAL 7016 (anthracite) - Shelf height 4,200 mm - Load capacity per upright 2,200 kg - Foot section and cantilever arms with 1,200 mm usable depth - Cantilever arms height-adjustable in 100 mm increments - 3 screw-on cantilever arms per upright, standard (= 4 storage levels) - Load capacity per cantilever arm 740 kg - Including longitudinal and diagonal bracing for 1,300 mm spacing - Shelf length = 4,000 mm - Including fixing material (without floor anchors) - With assembly instructions and load plates C4 according to DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with notification prior to delivery. The material is sensibly packed to enable easy unloading. Delivery can be made in approx. 1 - 2 weeks after receipt of order. For outdoor installation, the load-bearing capacity is reduced by the wind and snow load. The surface must be concrete, level and suitable for dowels and must be able to bear the loads. The customer must check and ensure that the ground conditions and load-bearing capacity as well as any necessary official approvals are in place. The shelf stands must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the employers' liability insurance association, it is recommended that the uprights on the uppermost storage level protrude at least 500 mm from the top edge of the uprights.

Condition: like new (used), Year of construction: 2025, Cantilever rack used: screw system in hot-dip galvanized design Scope of delivery: 4 shelf uprights, height 3,500 mm with foot section, 1,200 mm usable depth 12 cantilevers with 1,200 mm usable depth, standard Including longitudinal and diagonal braces for 1,300 mm spacing Fastening material (screws, nuts and washers) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 40 uprights in stock) Detailed description: - Stable steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Shelf height 3,500 mm - Load capacity per upright 2,250 kg - Foot section and cantilever arms with 1,200 mm usable depth Cantilever arms in Height adjustable in 100 mm increments - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and C4 load plates in accordance with DIN standard Dsdpfx Agsmhh Dho Dokk - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are manufactured exclusively in Germany. We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: like new (used), Year of construction: 2025, Used cantilever rack: screw system in hot-dip galvanized design Scope of delivery: 4 rack stands, height 2,600 mm with base section 1,000 mm 12 cantilevers with 1,000 mm depth, standard Including longitudinal and diagonal braces for 1,300 mm axle spacing Incl. fastening material (without ground anchors) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 90 stands in stock) Detailed description: - Stable steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Rack height 2,600 mm - Load capacity per stand 1,800 kg - Base section and cantilevers with 1,000 mm usable depth - Cantilevers in 100 mm increments height adjustable - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 600 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and load plates C4 in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - Collection on site possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with registration before delivery. Dsdpfed Tbbdex Ag Dekk The material is packed sensibly to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: like new (used), Year of construction: 2025, Used cantilever racking: Screw system in hot-dip galvanized design Dkedpfx Agsfdkb Ts Dok Scope of delivery: 4 shelf uprights Height 4,160 mm with base section 1,200 mm usable depth 12 cantilever arms with 1,200 mm usable depth, standard Longitudinal and diagonal braces for 4,000 mm shelf length (spacing 1,300 mm) Fastening material (screws, nuts and washers) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Replacement parts can be reordered and extended at any time) - (*Offer available in larger quantities: approx. 90 stands in stock) Detailed description: - Sturdy steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Shelf height 4,160 mm - Load capacity per upright 2,250 kg - Base section and cantilever arms with 1,200 mm usable depth - Cantilever arms height-adjustable in 100 mm increments - 3 screw-on cantilever arms per upright, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal bracing for 1,300 mm spacing - Shelf length = 4,000 mm - Including fixing material (without floor anchors) - With assembly instructions and load plates C4 according to DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with notification prior to delivery. The material is sensibly packed to enable easy unloading. For outdoor installation, the load-bearing capacity is reduced by the wind and snow load. The base must be concrete, level and suitable for dowels and be able to bear the loads. The customer must check and ensure that the ground conditions and load-bearing capacity as well as any official approvals that may be required. The shelf stands must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the employers' liability insurance association, it is recommended that the uprights on the uppermost storage level protrude at least 500 mm from the top edge of the uprights.

Condition: like new (used), Year of construction: 2025, Cantilever rack used: screw system in hot-dip galvanized design Scope of delivery: 4 shelf uprights, height 2,600 mm with foot section, 1,000 mm usable depth 12 cantilevers with 1,000 mm usable depth, standard Including longitudinal and diagonal braces for 1,300 mm spacing Fastening material (screws, nuts and washers) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 40 uprights in stock) Detailed description: - Stable steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Shelf height 2,600 mm - Load capacity per upright 1,800 kg - Foot section and cantilever arms with 1,000 mm usable depth Cantilever arms in Height adjustable in 100 mm increments - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 600 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and C4 load plates in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are manufactured exclusively in Germany. We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports. Dksdpfx Agjmhh Dzo Djk

Condition: like new (used), Year of construction: 2025, Cantilever rack used: screw system in hot-dip galvanized design Scope of delivery: 4 shelf uprights, height 3,000 mm with foot section, 1,200 mm usable depth 12 cantilevers with 1,200 mm usable depth, standard Including longitudinal and diagonal braces for 1,300 mm spacing Fastening material (screws, nuts and washers) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) Dsdpfomhhx Iex Ag Dskk - (*Offer available in larger quantities: approx. 40 uprights in stock) Detailed description: - Stable steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Shelf height 3,000 mm - Load capacity per upright 2,250 kg - Foot section and cantilever arms with 1,200 mm usable depth Cantilever arms in Height adjustable in 100 mm increments - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and C4 load plates in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are manufactured exclusively in Germany. We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: like new (used), Year of construction: 2025, Cantilever rack used: screw system in hot-dip galvanized design Scope of delivery: 4 shelf uprights, height 2,600 mm with foot section, 1,000 mm usable depth 12 cantilevers with 1,000 mm usable depth, standard Including longitudinal and diagonal braces for 1,300 mm spacing Fastening material (screws, nuts and washers) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 40 uprights in stock) Detailed description: - Stable steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Shelf height 2,600 mm - Load capacity per upright 1,800 kg - Foot section and cantilever arms with 1,000 mm usable depth Cantilever arms in Height adjustable in 100 mm increments - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 600 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and C4 load plates in accordance with DIN standard Dkedpemhhyaofx Ag Dek - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are manufactured exclusively in Germany. We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: like new (used), Year of construction: 2024, Cantilever rack double-sided used: Hot-dip galvanized screw system Scope of delivery: 4 double-sided shelf stands, height 4,160 mm with foot section 1,200 mm 24 cantilevers with 1,200 mm depth, standard Including longitudinal and diagonal braces for 1,300 mm axle spacing Incl. fastening material (without ground anchors) Dkedpfx Ageh Ek Das Djk - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Also available in larger quantities: 20 stands in stock) Detailed description: - Stable steel construction made of IPE profiles - Surface of all components hot-dip galvanized - Load capacity per stand side 2,250 kg - Load capacity per cantilever arm 750 kg - Cantilever arms height adjustable in 100 mm increments - 6 screwable cantilever arms per stand and 2 base sections with a depth of 1,200 mm, standard = 4 storage levels one above the other per side of the stand - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and load plates C4 in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - Collection on site possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: like new (used), Year of construction: 2025, Cantilever rack used: screw system in hot-dip galvanized design Scope of delivery: 4 shelf uprights, height 3,000 mm with foot section, 1,200 mm usable depth 12 cantilevers with 1,200 mm usable depth, standard Including longitudinal and diagonal braces for 1,300 mm spacing Fastening material (screws, nuts and washers) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 40 uprights in stock) Detailed description: - Stable steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Shelf height 3,000 mm Dkedemhh Anjpfx Ag Dek - Load capacity per upright 2,250 kg - Foot section and cantilever arms with 1,200 mm usable depth Cantilever arms in Height adjustable in 100 mm increments - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and C4 load plates in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are manufactured exclusively in Germany. We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: like new (used), Year of construction: 2025, Used cantilever rack: screw system in hot-dip galvanized design Scope of delivery: 4 shelf uprights, height 4,160 mm with foot section, 1,200 mm usable depth Dkodsd Tqalepfx Ag Djk 12 cantilevers with 1,200 mm usable depth, standard Longitudinal and diagonal struts for 4,000 mm shelf length (distance 1,300 mm) Fastening material (screws, nuts and washers) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 90 uprights in stock) Detailed description: - Stable steel construction made of IPE profiles (screw system) - Surface hot-dip galvanized - Shelf height 4,160 mm - Load capacity per upright 2,250 kg - Foot section and cantilever arms with 1,200 mm Usable depth - Cantilever arms height adjustable in 100 mm increments - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and C4 load plates in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are manufactured exclusively in Germany. We offer reliable freight with registration before delivery. The material is packed sensibly to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and suitable for dowels and must be able to absorb the loads. The customer must check and ensure that the floor conditions and load-bearing capacity, as well as any official permits that may be required, are obtained. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and is not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: like new (used), Year of construction: 2025, Used cantilever rack: screw system in hot-dip galvanized design Scope of delivery: 4 rack stands, height 3,500 mm with base section 1,200 mm 12 cantilevers with 1,200 mm usable depth, standard Including longitudinal and diagonal braces for 1,300 mm axle spacing Incl. fastening material (without ground anchors) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 40 stands in stock) Detailed description: - Stable steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Rack height 3,500 mm - Load capacity per stand 2,250 kg - Base section and cantilevers with 1,200 mm usable depth - Cantilevers in 100 mm increments height adjustable - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and load plates C4 in accordance with DIN standard Dkodpfx Ajfdkb Usg Djk - Expert advice by telephone - Made in Germany - Short delivery time - Collection on site possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: as good as new (ex-display), Year of construction: 2024, Cantilever rack in painted version (RAL 7016 anthracite): Scope of delivery: 4 shelf uprights height 2.56 m with base section 1.0 m usable depth (1.2 m total depth) 12 cantilever arms with 1.0 m usable depth Longitudinal and diagonal braces for 4 m shelf length (spacing 1.3 m) Fastening material (screws, nuts and washers) (*No paint damage!) Djdpfxsguk A Hs Ag Dokk Net price on collection: € 1,490.00 plus VAT. Delivery possible for an additional charge Detailed description: - Sturdy steel construction made of IPE profiles (screw system) - Surface painted in RAL 7016 (anthracite) - Shelf height 2,560 mm - Load capacity per upright 1,800 kg - Foot section and cantilever arms with 1,000 mm usable depth - Cantilever arms height-adjustable in 100 mm increments - 3 screw-on cantilever arms per upright, standard (= 4 storage levels) - Load capacity per cantilever arm 600 kg - Including longitudinal and diagonal bracing for 1,300 mm spacing - Shelf length = 4,000 mm - Including fixing material (without floor anchors) - With assembly instructions and load plates C4 according to DIN standard - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with notification prior to delivery. The material is sensibly packed to enable easy unloading. The substrate must be made of concrete, be level and suitable for dowels and be able to bear the acting loads. The customer is responsible for checking and ensuring the ground conditions and load-bearing capacity as well as any official approvals required. The shelf stands must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the employers' liability insurance association, it is recommended that the uprights on the uppermost storage level protrude at least 500 mm from the top edge of the uprights.

Condition: like new (used), Year of construction: 2025, Used cantilever rack: screw system in hot-dip galvanized design Scope of delivery: 4 rack stands, height 3,000 mm with base section 1,200 mm 12 cantilevers with 1,200 mm usable depth, standard Dedpfx Aefdkbhsg Dskk Including longitudinal and diagonal braces for 1,300 mm axle spacing Incl. fastening material (without ground anchors) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 50 stands in stock) Detailed description: - Stable steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Rack height 3,000 mm - Load capacity per stand 2,250 kg - Base section and cantilevers with 1,200 mm usable depth - Cantilevers in 100 mm increments height adjustable - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and load plates C4 in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - Collection on site possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: like new (used), Year of construction: 2024, Used cantilever rack: screw system in hot-dip galvanized design Scope of delivery: 4 rack stands, height 3,000 mm with base section 1,200 mm 12 cantilevers with 1,200 mm usable depth, standard Including longitudinal and diagonal braces for 1,300 mm axle spacing Incl. fastening material (without ground anchors) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 50 stands in stock) Detailed description: Dedpfsguk Dkox Ag Dskk - Stable steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Rack height 3,000 mm - Load capacity per stand 2,250 kg - Base section and cantilevers with 1,200 mm usable depth - Cantilevers in 100 mm increments height adjustable - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and load plates C4 in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - Collection on site possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: like new (used), Year of construction: 2025, Used cantilever rack: screw system in hot-dip galvanized design Scope of delivery: 4 rack uprights, height 4,160 mm with foot section, 1,200 mm usable depth 12 cantilevers with 1,200 mm usable depth, standard Longitudinal and diagonal struts for 4,000 mm rack length (distance 1,300 mm) Fastening material (screws, nuts and washers) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 90 uprights in stock) Detailed description: - Stable steel construction made of IPE profiles (screw system) - Surface hot-dip galvanized - Rack height 4,160 mm - Load capacity per upright 2,250 kg - Foot section and cantilever arms with 1,200 mm Usable depth - Cantilever arms height adjustable in 100 mm increments - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and C4 load plates in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time Dkedpomhhf Sjfx Ag Dsk - On-site collection possible Our cantilever racks are manufactured exclusively in Germany. We offer reliable freight with registration before delivery. The material is packed sensibly to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and suitable for dowels and must be able to absorb the loads. The customer must check and ensure that the floor conditions and load-bearing capacity, as well as any official permits that may be required, are obtained. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and is not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: like new (used), Year of construction: 2024, Screw system in hot-dip galvanized design: Pick-up price: Dksdpsmhhl Hofx Ag Dsk Sturdy steel construction made of IPE profiles Shelf height 3500 mm Load capacity per upright 2100 kg Foot section 1200 mm usable depth Cantilever arms height-adjustable in 100 mm increments 3 screw-on cantilever arms per upright Usable depth 1200 mm, standard (= 4 levels) Load capacity per cantilever arm 700 kg Including longitudinal and diagonal bracing Including fastening material (without ground anchors) With assembly instructions and load plates C4 according to DIN standard

Condition: like new (used), Year of construction: 2025, Cantilever rack with roof supports: Hot-dip galvanized bolted system Scope of delivery: - 9 rack uprights, height 4,230 mm with base section, usable depth 1,200 mm - 27 cantilever arms, 1,200 mm usable depth, with guards - 9 roof supports with 1,500 mm cantilever, pre-drilled for on-site roof construction (*Excluding timber purlins and trapezoidal metal sheets for the roof structure) - Includes longitudinal and diagonal braces for 1,500 mm upright spacing - Incl. mounting hardware (excluding floor anchors) Dkjdpfjmhhy Nsx Ag Djk - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Spare parts and extensions available to order at any time) - (*Offer available in larger quantities: approx. 50 uprights in stock) Detailed description: - Robust steel construction made from IPE profiles - All components hot-dip galvanized - Load capacity per upright: 2,700 kg plus additional roof, wind, and snow load (Maximum snow load 1.85 kN/m² and wind load zone 2) - Load capacity per cantilever arm: 900 kg - Including roof supports (Maximum snow load 1.85 kN/m² and wind load zone 2) - Cantilever arms height adjustable in 100 mm increments - Per upright: 3 bolted cantilever arms, depth 1,200 mm, with guards = 4 storage levels - Including longitudinal and diagonal braces with 1,500 mm upright spacing - Rack length: 12,100 mm - Including mounting hardware (without floor anchors) - With assembly instructions and C4 load labels according to DIN standard - Specialist telephone consultation - Made in Germany - Short delivery times - On-site pickup possible Our cantilever racks are manufactured exclusively in Germany. We offer reliable freight services with advance notice before delivery. The material is thoughtfully packaged to facilitate easy unloading. The substructure must be concrete, level, and suitable for dowel anchoring, and capable of bearing the applied loads. The floor condition and load-bearing capacity, as well as any required official permits, must be checked and ensured by the customer. The rack uprights must be anchored to the floor on site. Anchoring to the wall is neither required nor recommended. According to Occupational Safety regulations, it is recommended that the uprights have at least 500 mm overhang above the top storage level.

Condition: like new (used), Year of construction: 2024, Cantilever rack in painted version (RAL 7016 anthracite): Scope of delivery: 4 rack uprights, height 4,200 mm with foot section, 1,200 mm usable depth 12 cantilevers with 1,200 mm usable depth Longitudinal and diagonal struts for 1,300 mm rack axis spacing (4,000 mm rack length) Fastening material (screws, nuts and washers) - (*No paint damage!) - (*No damaged components!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 50 racks in stock) Net price: €1,990.00 plus VAT Detailed description: - Stable steel construction made of IPE profiles (screw system) - Surface painted in RAL 5010 (gentian blue) - Rack height 4,200 mm - Load capacity per stand 2,200 kg - Base and cantilever arms with 1,200 mm usable depth - Cantilever arms height adjustable in 100 mm increments - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 730 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without floor anchors) - With assembly instructions and load plates C4 in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are manufactured exclusively in Germany. We offer reliable freight with registration before delivery. Dedpfx Aomidyfjg Djkk The material is sensibly packed to enable easy unloading. Delivery can take place in approx. 1 - 2 weeks after receipt of the order. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-compatible and must be able to bear the loads. The customer must check and ensure that the soil condition and load-bearing capacity as well as any official permits that may be required are obtained. The shelf supports must be anchored to the ground on site; anchoring to the wall is not necessary and is not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm from the top edge of the stand.

Condition: like new (used), Year of construction: 2024, Cantilever rack double-sided used: Hot-dip galvanized screw system Scope of delivery: 4 double-sided shelf uprights, height 3,500 mm with foot parts each 1,200 mm 24 cantilevers with 1,200 mm depth, standard Including longitudinal and diagonal braces for 1,300 mm axle spacing Incl. fastening material (without ground anchors) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) Dksdpfx Ajmkixwjg Dok - (*Also available in larger quantities: 20 uprights in stock) Detailed description: - Stable steel construction made of IPE profiles - Surface of all components hot-dip galvanized - Load capacity per upright side 2,250 kg - Load capacity per cantilever arm 750 kg - Cantilever arms height adjustable in 100 mm increments - 6 screwable cantilevers per upright and 2 foot parts with a depth of 1,200 mm, standard = 4 storage levels one above the other per stand side - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and load plates C4 in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - Collection on site possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: like new (used), Year of construction: 2025, Used cantilever rack: screw system in hot-dip galvanized design Scope of delivery: 4 shelf uprights, height 4,160 mm with foot section, 1,200 mm usable depth 12 cantilevers with 1,200 mm usable depth, standard Longitudinal and diagonal struts for 4,000 mm shelf length (distance 1,300 mm) Fastening material (screws, nuts and washers) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 90 uprights in stock) Detailed description: - Stable steel construction made of IPE profiles (screw system) - Surface hot-dip galvanized - Shelf height 4,160 mm - Load capacity per upright 2,250 kg - Foot section and cantilever arms with 1,200 mm Usable depth - Cantilever arms height adjustable in 100 mm increments - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and C4 load plates in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are manufactured exclusively in Germany. Dsdpfomhh Dtjx Ag Djkk We offer reliable freight with registration before delivery. The material is packed sensibly to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and suitable for dowels and must be able to absorb the loads. The customer must check and ensure that the floor conditions and load-bearing capacity, as well as any official permits that may be required, are obtained. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and is not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: new, Year of construction: 2024, carrying capacity per cantilever arm: 500 kg, shelf height: 3,200 mm, total length: 2,100 mm, total height: 3,200 mm, axle spacing: 1,000 mm, load capacity per stand: 2,500 kg, Cantilever rack in hot-dip galvanized design: Scope of delivery: 3 rack stands, height 3.2 m with base section, 1.8 m usable depth (2 m total depth) 12 cantilevers with 1.8 m usable depth (for chipboard with approx. 2.1 m depth) Longitudinal and diagonal struts for 4 m rack length (distance 1.3 m) Fastening material (screws, nuts and washers) Net price: €2,490.00 plus VAT Detailed description: - Stable steel construction made of IPE profiles (screw system) - Rack height 3,200 mm - Load capacity per stand 2,500 kg - Base section and cantilevers with 1,800 mm usable depth - (for 2,100 mm chipboard depth) - Cantilevers height adjustable in 100 mm increments - 4 screwable screws per stand Cantilever arms, standard (= 5 storage levels) - Load capacity per cantilever arm 500 kg - Including longitudinal and diagonal braces for 1,000 mm spacing - Shelf length = 2,100 mm - Including fastening material (without ground anchors) - With assembly instructions and load plates C4 in accordance with DIN standard - Made in Germany - Short delivery time Our cantilever racks are produced exclusively in Germany. We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. Delivery for stock items can take place in approx. 1 week after receipt of the order. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. Dkodpfxoqt Dmyj Ag Dsk The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: like new (used), Year of construction: 2025, Used cantilever rack: screw system in hot-dip galvanized design Scope of delivery: 4 rack stands, height 2,600 mm with base section 1,000 mm 12 cantilevers with 1,000 mm depth, standard Including longitudinal and diagonal braces for 1,300 mm axle spacing Incl. fastening material (without ground anchors) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 90 stands in stock) Detailed description: - Stable steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Rack height 2,600 mm - Load capacity per stand 1,800 kg - Base section and cantilevers with 1,000 mm usable depth - Cantilevers in 100 mm increments height adjustable - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 600 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and load plates C4 in accordance with DIN standard - Expert advice by telephone - Made in Germany Dodpsguk Dvofx Ag Dokk - Short delivery time - Collection on site possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with registration before delivery. The material is packed sensibly to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: excellent (used), Nagy PB-80 Extension Bay for Pallet Racking With a standard pallet height of 1.20 m, you can install 6 beam levels in the 10.3 m high extension bay. Together with the floor-level storage spaces, this results in 7 storage levels, which, with 4 pallets per bay, provides a total of 28 pallet spaces per bay. Material & Construction: The galvanized surface offers long-lasting corrosion protection. Dkjdpfxsyvr Dgj Ag Dok Unlike welded frames, the bolted truss construction (diagonal and cross braces) allows for easy replacement of individual components in case of damage (e.g., from forklift impacts). Profile: The 80 x 60 mm profile dimensions are typical for medium to heavy-duty pallet racking uprights to ensure the necessary buckling stiffness at heights exceeding 10 meters. Manufacturer: Nagy Type: PB-80 Upright height: approx. 10.30 m Upright depth: approx. 1.10 m Upright type: PB-80 Profile: 80 x 60 mm Troop frame: bolted Upright finish: galvanized Clear span: 3.60 m Crossbeam: 3600 x 120 x 45 mm Crossbeam finish: blue painted (RAL 5015) Number of bays: 1 add-on bay Number of levels: 7 incl. floor storage space Max. pallet weight: 500 kg Permissible bay load: 2000 kg Permissible bay load: 12000 kg Pallet spaces: 28 Scope of delivery 1 x upright approx. 10.30 x 1.10 m galvanized 12 x crossbeams approx. 3.60 m blue incl. locking pins Your Partner for safe warehouse logistics: Assembly, disassembly & racking inspection An efficient warehouse is the backbone of your success. We ensure that your racking systems are professionally installed and meet all safety standards. As experts in warehouse technology, we offer you everything from a single source: Assembly & Disassembly Whether new installation, conversion, or warehouse closure – we handle the professional assembly and disassembly of your systems: - Pallet racking (heavy-duty & standard) - Shelving for small parts and archives - Mezzanine floors for optimal space utilization Racking inspection & testing according to DIN EN 15635 Safety is a legal obligation. We conduct the annual expert inspection (according to DGUV Regulation 108-007): - Inspection for deformations and damage. - Checking of safety pins and load capacity labels. - Creation of a legally compliant inspection report including an inspection sticker. We would be happy to offer you suitable bank financing for your project. komplett-konzept.leasingo.de Find more pallet racking – new and used – in our shop! International shipping costs on request!

Condition: excellent (used), 7.4 m Nagy PB-80 Pallet Rack With a standard pallet height of 1.20 m, you can install 6 beam levels in the 10.3 m high rack. Together with the floor-level storage spaces, this results in 7 storage levels, which, with 4 pallets per bay, provides a total of 28 pallet spaces per bay. Material & Construction: The galvanized surface offers long-lasting corrosion protection. Unlike welded frames, the bolted truss construction (diagonal and cross braces) allows for easy replacement of individual components in case of damage (e.g., from forklift impacts). Profile: The 80 x 60 mm profile dimensions are typical for medium to heavy-duty pallet rack uprights to ensure the necessary buckling stiffness at heights exceeding 10 meters. Dkjdpsyvr Aiefx Ag Dok Manufacturer: Nagy Type: PB-80 Shelf length: approx. 7.40 m Upright height: approx. 10.30 m Upright depth: approx. 1.10 m Upright type: PB-80 Profile: 80 x 60 mm Frame: bolted Upright finish: galvanized Clear span: 3.60 m Crossbeam: 3600 x 120 x 45 mm Crossbeam finish: blue painted (RAL 5015) Number of bays: 2 (basic bay + 1 extension bay) Number of levels: 7 incl. floor storage space Max. pallet weight: 500 kg Permissible shelf load: 2000 kg Permissible bay load: 12000 kg Pallet spaces: 56 Scope of delivery 3 x uprights approx. 10.30 x 1.10 m galvanized 24 x Crossbeam approx. 3.60 m blue incl. locking pins Your partner for safe warehouse logistics: Assembly, disassembly & rack inspection An efficient warehouse is the backbone of your success. We ensure that your racking systems are professionally installed and meet all safety standards. As experts in warehouse technology, we offer you everything from a single source: Assembly & Disassembly Whether new installation, conversion, or warehouse closure – we handle the professional assembly and disassembly of your systems: - Pallet racking (heavy-duty & standard) - Shelving for small parts and archives - Mezzanine floors for optimal space utilization Rack inspection & testing according to DIN EN 15635 Safety is a legal obligation. We conduct the annual expert inspection (according to DGUV Regulation 108-007): - Inspection for deformations and damage. - Checking of locking pins and load capacity labels. - Creation of a legally compliant inspection report including an inspection sticker. We would be happy to offer you suitable bank financing for your project. komplett-konzept.leasingo.de You can find more pallet racking – new and used – in our shop! International shipping costs on request!

Condition: excellent (used), Nagy PB-80 Base Unit for Pallet Racking With a standard pallet height of 1.20 m, you can install 6 beam levels in the 10.3 m high racking unit. Together with the floor-level storage spaces, this results in 7 storage levels, which, with 4 pallets per bay, provides a total of 28 pallet spaces per racking unit. Material & Construction: The galvanized surface offers long-lasting corrosion protection. Unlike welded frames, the bolted truss construction (diagonal and cross braces) allows for easy replacement of individual components in case of damage (e.g., from forklift impacts). Profile: The 80 x 60 mm profile dimensions are typical for medium to heavy-duty pallet racking uprights to ensure the necessary buckling stiffness at heights exceeding 10 meters. Manufacturer: Nagy Type: PB-80 Upright height: approx. 10.30 m Dkodpfoyvrynex Ag Dsk Upright depth: approx. 1.10 m Upright type: PB-80 Profile: 80 x 60 mm Troop frame: bolted Upright finish: galvanized Clear span: 3.60 m Crossbeam: 3600 x 120 x 45 mm Crossbeam finish: blue painted (RAL 5015) Number of bays: 1 basic bay Number of levels: 7 including floor storage space Max. pallet weight: 500 kg Permissible bay load: 2000 kg Permissible bay load: 12000 kg Pallet spaces: 28 Scope of delivery 2 x uprights approx. 10.30 x 1.10 m, galvanized 12 x crossbeams approx. 3.60 m, blue, including locking pins Your partner For safe warehouse logistics: Assembly, disassembly & racking inspection An efficient warehouse is the backbone of your success. We ensure that your racking systems are professionally installed and meet all safety standards. As experts in warehouse technology, we offer you everything from a single source: Assembly & Disassembly Whether new installation, conversion, or warehouse closure – we handle the professional assembly and disassembly of your systems: - Pallet racking (heavy-duty & standard) - Shelving for small parts and archives - Mezzanine floors for optimal space utilization Racking inspection & testing according to DIN EN 15635 Safety is a legal obligation. We conduct the annual expert inspection (according to DGUV Regulation 108-007): - Inspection for deformations and damage. - Checking of safety pins and load capacity labels. - Creation of a legally compliant inspection report including an inspection sticker. We would be happy to offer you suitable bank financing for your project. komplett-konzept.leasingo.de Find more pallet racking – new and used – in our shop! International shipping costs on request!