Clamping angle

Stankoimport 500 x 200 mm

Condition: repair required (used), Machine number: 1464 TyP / Model: FUW 250/IV travel x-y-z: 400 - 220 - 400 mm table: 630 x 350 mm table clamping surface: 700 x 300 mm Kfsdpfx Aod Hl Stja Eea speed range: 45 to 2.240 rpm spindle mounting: SK 40 feed range longitudinal: 6,3 to 1.250 mm/min feed range cross: 6,3 to 1.250 mm/min Connection: 7.4 kW accessories/equipment: vertical head Condition: 2 controllers defective Note: machine repair EUR 2.000 weight: 1,45 t dimensions: 1.500 x 1.600 x 1.800 mm

Condition: used, Technical details: balancing body max.: 800 kg balancing body diameter: 1250 mm Balancing revolution per minute: 190 - 3600 U/min bed length: 2600 mm voltage: 380 V/Hz drive power: 7,5 kw Weight approx.: 1,5 t dimension machine xH: 3,5 x 1,7 x 2,0 m dimensions electric cabinet: B:650 x T:250xH:800 mm Horizontal balancing machine The balancing machine is used to measure and balance the static or dynamic unbalance of rotors. Balancing body weight max. 800 kg with equal load distribution, i.e. 400 kg per bearing pedestal Kfodju Upp Tjpfx Aa Eea Power transmission by means of cardan shaft Bearing journal Ø min./max.: 16-95 / 95-180 mm Bearing distance center distance min. 125 mm and shaft end bearing center max. 2070 mm Measured speed: 1st gear = 190 - 650 rpm. 2nd gear = 400 - 1250 rpm 3rd gear = 700 - 2100 rpm. 4th gear = 1200 - 3600 rpm. 2 pick-up blocks whose displacement is manual over the entire bed Schenk measuring device with digital display and some accessories, e.g. many rotor shafts with different Ø and different rotor mounts, please ask! *

Condition: good (used), Year of construction: 2000, total height: 47,000 mm, total width: 27,000 mm, total length: 25,000 mm, table width: 1,000 mm, table length: 1,800 mm, overall weight: 43,000 kg, ram plate width: 600 mm, die cushion stroke: 200 mm, Siemens Simatic OP 27 control system Ksdetiwgispfx Aa Eofa Light barrier Sick Separate control cabinet Ritta Side passages Ground level installation

Condition: new, – Capacity 42 x 3 mm – Hydraulic – Adjustable stroke – Emergency stop – With 3 tool sets 33.7 mm, 26.9 mm, 21.3 mm – Documentation – 400V Kfodpfx Aepivd Aja Eoa

Condition: used, Year of construction: 1987, pressure / t stroke / mm table-size / mm weight of the machine ca. 65000 kg Make: Shepherd Type: SVRM 4-roller bending machine: Year of construction: 1986 Working width: 3000cm Ksdouddcaspfx Aa Eofa Smallest pipe diameter with 600 mm roller: Ø 720 mm Smallest tube diameter with 360 mm roller: Ø 460 mm Sheet thickness up to (depending on the material): 50 mm Material SA- 738 B Working width: 2500 mm Material SA- 738 B Material thickness: 35 mm conical bending: Except for the top roller, all rollers can be moved in an inclined position for conical bending. The roller positions can be read on display instruments. For semi-automatic or fully automatic operation of the machine, the bearing jewels of the rollers are equipped with scale bars and slide cams for limit switch actuation. This allows the rollers to return to the same set position over and over again, giving a very high level of uniformity in the shot wefts being bent.

Year of construction: 2009, condition: excellent (used), Max. length of plate 3000 mm Max. plate thickness 40 mm Number of rolls 3 pcs Upper roll diameter 550 mm Lower roll diameter 450 mm Control Roundo WCN Ksdpfx Ajn Atnlea Eefa Main motor power 94 Kw Equipped with: Pre-bending, hydraulic, three roll drive, cone bending divice Electro-hydraulic operation of drop-end, top support Side supports, roller conveyor, Service tools etc.

Condition: used, Year of construction: 2007, pressure 315 t distance between columns 1750 mm stroke 700 mm distance table/ram, max. stroke up, adjustment up 1200 mm table surface area 1600 x 1500 mm pressure of drawing cushion in table 125 t stroke of drawing cushion in table 200 mm die cushion area 1200 x 1400 mm table height over floor 750 mm ram surface 1640 x 1500 mm power requirement 55,0 + 11,0 kW weight 29,5 t dimensions (WxDxH) 3,2 x 4,5 x 5,8 m Kodovuukbepfx Aa Ejfa Height above floor 5,1 m year of manufacture 1983 - 2007: modernization of electrical control (Siemens S 7) permitted for manual put-in according to the CE Regulations with oil-hydraulic drive, hydraulic drawing cushion in table, hydraulic cutting impact cushioning can be offered without putting into operation, with putting into operation in given condition or alternatively with new control Siemens S 7-1500 F

Condition: used, Year of construction: 1973, pressure 200 t chamfer lenght 3600 mm distance between columns 2650 mm dayligth 500 mm throat 300 mm stroke 250 mm working feed 10,5 mm/sec return speed 100 mm/sec ram stroke speed 150 mm/sec table height 900 mm oil volume 500 l total power requirement 37 kW Ksdet I D U Eopfx Aa Eofa weight of the machine ca. 17800 kg dimensions of the machine ca. 3710 x 1800 x 3390 mm Equipment: - Controlled axes Y1 + Y2 - Manual X-axis with digital position display - Set of upper and lower tools - 2x stop fingers - 2x front support arms - Hand and foot controls - Side + rear safety guard - Operating instructions

Condition: used, MULLER 250t PRESSURE: 250t STROKE: 550mm Ksdporfxhkofx Aa Eofa TABLE DIMENSIONS: 2500x1400mm

Condition: used, Year of construction: 2007, pressure 100 t stroke 500 mm table surface area 900 x 600 mm rapid traverse 22 mm/s stroke speed 2 mm/s ram surface 700 x 350 mm total power requirement 2,2 kW weight of the machine ca. 1,6 t dimensions of the machine ca. 1,9 x 0,85 x 2,3 m The machine is of the Italian make SICMI, which was traded by the Knuth company. Kodsvprv Rspfx Aa Ejfa