Used Water Recycling System for sale (9,963)

Condition: new, Year of construction: 2024, Gold River SWZ-700 water separators Application description: The GOLD RIVER SWZ series separator has been designed for special tasks, it can cope with the most difficult materials that contain many properties that disturb the separation process in separators commonly available on the market. SWZ water separators separate heavy fractions (non-ferrous metals) from, among others, plastics in the process of recycling secondary raw materials. SWZ separator equipped with a four-section copper water system equipped with radial nozzles with variable linear geometry. The separator uses the latest divided type of separation mat. The development of a modern module for preliminary division and preparation of material guarantees the purity of recovered raw materials in a very short time (plastics, metals). Why a water system? Our device uses a system similar to that used in the gold recovery industry. We use water as a carrier and a force that affects the materials in a gentle way. In the water system, all particles with higher mass are gently washed out and separated, generating no losses during the entire separation process. The properties of water together with our proprietary solutions are unrivaled compared to, for example, air separators. SWZ type separators are used: Separation of heavy from light materials (metal granulates contaminated with plastic, foil, paper, cotton, fibers) Cleaning plastics after air separators (dry) Separation of metals in cable and non-ferrous metal recycling lines The SWZ-700 water separator, thanks to the use of the latest module, performs the separation process in a very short time, therefore it is characterized by a high hourly efficiency of separated material of approximately 1200 kg/h. Todpfxeua Tbwe Ahusf Description of action: The material fed into the separator goes through the transport channel to the module for initial fraction division into its mass and humidity changes. Some of the material is separated at this stage. In the second part of the module, the humidity of the remaining batch changes. Then the material falls onto the separation table where the final fraction separation takes place. As a result of this process, we obtain valuable materials from both sides of the separator. Construction description: The massive structure and the inertial drive of the separator are made of materials appropriately selected to withstand the overloads resulting from vibrations. The supporting frame ensures excellent stiffness and failure-free operation for many years. Due to the type of vibration drive, the design does not require the installation of a soil separator. Separation table equipped with hydraulic adjustment of the angle of inclination. The separation table has a special module for initial division of fractions into their mass and preparation for final separation. The water system has several water pressure valves. The water circulation in the separator is closed. There is no need for constant access to an external water source because the device works using the water already in the tanks. Based on experience and continuous research in our laboratories. We are able to provide you with separators individually adapted to the specific nature of the material being separated. In various versions and sizes. SWZ-700 separators are manufactured to individual order.

Condition: good (used), Young used vibrating sieve to filter process water. Made of 304 stainless steel, also suitable for salt solutions. Tjdpfx Aovy Dy Nshuof

Condition: new, Year of construction: 2025, Built on order Vibrating sieve to filter the process water. Tsdpfxskzg Sdj Ahuef Process water is preferably used in a closed circuit. The authorities also see this as the ideal solution. Obtaining the permits for a recycling plant is greatly simplified by the use of a closed circuit and the costs of using the plant are significantly lower.

Condition: used, This listing is for the Veolia/Elga PC1ANRXM2 Purelab Choruss The unit is in full working condition and is ready for immediate release The Veolia ELGA PURELAB Chorus 1 Complete is a high-performance water purification system engineered for laboratories demanding the highest water purity. It is ideal for supporting analytical research, quality control (QC) testing, and pharmaceutical manufacturing processes, delivering reliable Type I ultrapure water. Key Specifications Water Quality: 18.2 MΩ·cm resistivity (Type I) Flow Rate: Up to 20 litres per hour Features: Tjdpfoxv A Uaox Ahujf Advanced PureSure® deionization for consistent water quality Fully recirculating system to maintain microbial purity Real-time TOC monitoring to ensure organic purity Integrated filtration for endotoxins, proteins, particulates USB data capture for performance validation Optional ELGA Biofilter for biologically active impurities Cost-effective design supporting QC testing to validate drug purity in pharmaceutical manufacturing Consumables engineered to minimise cost and environmental waste Ideal Applications Analytical Research Life Sciences Pharmaceutical QC Testing Glassware Washing and Ultrapure Feed Systems

Condition: new, Year of construction: 2025, functionality: fully functional, warranty duration: 24 months, New filling machine / filler suitable for filling liquids, pastes, creams, oils, etc. Typical applications include: - Disinfectants - Shampoos - Creams - Honey - Jam - Milk - Yogurt - Water - Alcohol - Pesto - And more This is a robust machine powered by compressed air and 220V, fully Plug and Play! Ideal for small-batch filling operations. Even a small compressor is sufficient to operate this machine. A compressor can be supplied upon request. The filler features a 500ml cylinder, enabling a maximum fill volume of 500ml per cycle. For larger volumes, multiple cycles can be programmed. The minimum stroke is 50ml, and any volume between 50ml and 500ml can be dispensed in one cycle. The unit comes with a large 25L hopper. Optionally, it is possible to connect the system to an IBC or 200L drum, allowing for faster processing of larger batches. The machine is equipped with a foot pedal and automatic mode. In automatic mode, it continuously fills, making high-volume filling quick and efficient. With the foot pedal, operators can fill at their own pace. Tsdpfxerivwfo Ahujf Depending on operator speed and fill quantity, 15–25 units per minute can be achieved, making this a very fast machine. It weighs approximately 15–20kg and is easily placed on a tabletop. The entire structure is made of stainless steel, ensuring high quality and durability. If you have any questions, please email us; we are happy to assist you with this or other machines. We also offer a labelling machine that pairs perfectly with the filling machine. We strive to respond within 24 hours and are available on working days from 09:00 to 17:30.

Condition: good (used), functionality: fully functional, Year of construction: 2016, operating hours: 500 h, Bunker dosing belt by R&T Recycling Technik Year of manufacture: 2016 Capacity: 2.5 m³ Drive: 1.5 kW Frequency-controlled feed belt Tedpfxexcuvis Ahusf This system was integrated into a small pilot plant for approximately 3 months in 2016. The unit is in excellent condition and ready for operation. As shown in photo no. ..., this unit can be transported on a large tandem car trailer.

Condition: excellent (used), Item: D-10800-BacTerminator BacTerminator BTM10FD11001 Tsdpfx Aheh Dxqvouof Water Disinfection Equipment Inclusive pumps, Control and other accessories. Nice condition

Condition: excellent (used), Year of construction: 2017, operating hours: 19,187 h, functionality: fully functional, pressing force: 140 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,500 kg, overall weight: 52,000 kg, Technical data baler: Manufacturer Bollegraaf Recycling Machinery B.V. Todpfx Aoxrta Eshusf Typ HBC 140 Year of construction 2017 Working hours 19,187 hours, stand October 2025 Press power main press 140 tons (max. 153,5 tons) Press power of pre-press 70 tons Feed channel 1,600 x 1,100 mm Capacity per cycle time 4,34 m³ Theoretic cycle time 16 sec. Bale size 1,100 x 1,100 mm Driving motor 2 x 75 kW Connected load 226 kW Full load current 428 A Tying system 5-fold vertical, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx. 30 tons/h bulk weight of 50 kg/cbm approx. 46 tons/h bulk weight of 100 kg/cbm approx. 82 tons/h Bale weight 800 up to 1300 kg, depends on material and bale lenght SPS controller (manuf., type) Telemecanique TSX Micro Operating panel (manuf., type) Schneider MAGELIS Touch Baler dimensions built up with hopper 13,200 x 27,000 x 7,344 mm (l x w x h) Transport dimensions only baler 13.200 x 2.750 x 3.450 mm (l x w x h) Machine weight baler approx. 52 tons Technical data chain belt conveyor: Manufacturer Bollegraaf Typ HBT 1216 Year of construction 2009 Driving motor 7,5 kW Length feeding conveyor 6,750 mm Length elevating conveyor 14,400 mm Length goose neck 2,150 mm Grade 30° Effecting width 1,754 mm Height of side wall feeding conv. 500 mm Height of side wall elevating conv. 800 mm Weight 16 t Pit dimensions 10,000 x 3,200 x 1,200 mm (l x w x d) Comments: The press is currently in operation and is to be replaced by a new machine in the 2nd quarter of 2026. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: new, Year of construction: 2025, functionality: fully functional, Young used sink float tank for separating hard plastics, can wash/sort. Made of stainless steel 304, also suitable for salt solutions. Tedpfx Ahsvy Dumjuef

Condition: used, This listing is for the Grant GD120 Water Bath/Circulator The unit is in full working condition and is ready for immediate use The Grant GD120 is a digitally controlled stirred water bath and circulator ideal for laboratory use, offering high precision and flexibility. Here's a breakdown of its features and capabilities: Key Features Immersion Thermostat with Intelligent Control Optimisation (ICO): Enables adaptive PID control for exceptionally stable temperature regulation. Integral Pump: Built-in circulation pump with a maximum flow rate of 17 L/min, allowing both sample immersion and external fluid circulation. User Interface: Equipped with a clear digital display, a rotor plus two-key control, timer function for reaction timing, and visual + audible alarms to notify operators of critical conditions. Todsxhfl Ejpfx Ahuof Preset Temperature Control: Supports one adjustable operating setpoint plus three preset temperature options for fast switching. Safety Features: Includes float-switch low liquid protection and an adjustable over-temperature cut-out for sample and user safety. Liquid Type Selection: Automatically adjusts heater power and temperature parameters depending on chosen liquid (e.g., water, oil, glycol mixtures). Temperature Range & Accuracy Plastic Tanks (P-series): From around ambient +5 °C up to ~99 °C. Stainless Steel Tanks (S-series): From –15 °C up to ~120 °C. High Stability: ±0.02 °C for stable temperature control. Technical Specifications & Obsolescence The GD120 series includes multiple tank sizes: plastic tanks (P5, P12, P18) and stainless steel tanks (S5, S12, S18, S26, S38), offering varied capacities for different lab needs. This series is now considered obsolete, though it remains functional and reliable for many applications. Supporting Documentation & Manual Operating Manual: The GD120 is covered by the general purpose stirred thermostatic baths manual (shared with GD100), outlining temperature settings, calibration procedures, safety guidance, and maintenance. Datasheet Summary: Positioned within the broader Grant Optima product range, the GD120 sits between simpler (GD100, up to 100 °C) and higher-spec models (GR150 up to 150 °C, GP200 up to 200 °C)

Condition: new, Year of construction: 2025, Alligator shear brand new AVAILABLE NOW, ex work IUT Beyeler AG, DE-06188 Landsberg Financing and rental possible. We are looking for used alligator shears! The McIntyre 407 Alligator shear is a non ferrous shear which is both affordable and efficient. It has a 407mm 16″ blade length and enough power and speed to handle a wide variety of cutting tasks. This versatile alligator shear was built originally for scrapyard use so is robust enough to withstand difficult working environments. It is now our most popular shear with thousands in daily use worldwide. The McIntyre 407 non ferrous scrap shear can handle: Automotive scrap Whole gear boxes Cylinder heads and blocks Tedpehq Nlgsfx Ahuof Oversized gate valves And of course all the usual non ferrous metal cutting tasks. It can also handle ferrous metals if needed.

Year of construction: 2025, condition: new, To separate and sort after the specific weight from light and heavy fraction. Useable for grain, aluminium/plastic, rubber/textile, cable-recycling, etc. Type and size are selectable, depending on the product and throughput. At constant machine length, it is possible to choose between working width from: 450mm, 600mm, 900mm. Tjdpfobbr Ipox Ahusf

Condition: good (used), functionality: fully functional, Year of construction: 2002, • 4 new EDI cells MK3 are available. • 7 EDI stations, each with 4 EDI cells MK3, will be dismantled. Tedpfx Aowy Uu Aohuef

Condition: excellent (used), operating hours: 2,658 h, functionality: fully functional, pressing force: 71 t, filling opening width: 1,000 mm, filling opening length: 1,620 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 600 kg, input current: 200 A, oil tank capacity: 1,250 l, empty load weight: 29,000 kg, Technical data baler: Manufacturer BOA Recycling Systems B.V. Type M75-45-A-5-1.6 Ecoline Year of construction 2021 Hours of operation 2,658 hours (as of May 2024) Number of pressed bales 42,212 pieces (as of May 2024) Press power main press 71,2 kN (71 t) Specific press capacity 9 kg/cm² Operating pressure 280 bar Cylinder stroke 2,200 mm Feed channel 1,620 x 1,000 mm Capacity per cycle time 2,4 m³ Theoretic cycle time 21 seconds Theoretic throughput rate 450 m³/hour Bale size 1,100 x 720 mm, length variably adjustable up to 1,400 mm Driving motor 45 kW Connected load 100 kW Current consumption 200 A Tying system 5-fold vertical, fully automatic, the press stamp is prepared for an additional 3-fold horizontal binding Throughput rate at a bulk weight of 30 kg/cbm approx. 13,6 tons/hour bulk weight of 50 kg/cbm approx. 24,2 tons/hour bulk weight of 100 kg/cbm approx. 36,4 tons/hour bulk weight of 150 kg/cbm approx. 54,7 tons/hour Tedpsu Thcvsfx Ahujf Bale weight up to 600 kg, depends on material Volume hydraulic oil tank 1,250 l SPS controller Siemens S7 1500 Operating panel Siemens SIMATIC HMI TOUCH Transport dimensions of press 10,000 x 2,800 x 3,385 mm (l x w x h) Press height set up with feed chute 4,743 mm Press height with conveyor belt 7,123 mm Machine weight baler approx. 29 tons Noise level <85 dB (A) Condition of the baler: With 2,658 operating hours, the press is almost as good as new and in very good condition, has hardly any signs of wear and is ready for immediate use. Due to larger material input quantities, the pressing force and throughput of the machine no longer meet the customer's current requirements and is therefore being replaced by a new 120 tonne baler. Only the baler is for sale, without conveyor belt and wire drawing stations. Comments: The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Year of construction: 2023, condition: new, Stock machine Completely redeveloped high efficiency centrifuge based on our many years of production experience with the predecessor of this centrifuge, we have made various improvements with regard to maintenance costs, downtime and wear and tear parts. Todpfehwdvcox Ahuof

Condition: ready for operation (used), Year of construction: 1999, machine/vehicle number: 9558, Used fully functional WJS waterjet cutting machine with KMT SLIV 50 HP pump. Machine is in disassembled condition and can not be inspected. Installation and commissioning will be done by us and is not included in the price. The machine can also be completely overhauled ( new control cabinet, new control and new CE. This would mean a surcharge of about 50.000€) Tjdpoi Hckrefx Ahujf

Condition: like new (used), Baktec water Dosing machine and chiller In good working condition for more information please sent an request Tedpfx Aoump Axehusf

Year of construction: 2025, condition: new, To separate and sort after the specific weight from light and heavy fraction. Useable for grain, aluminium/plastic, rubber/textile, cable-recycling, etc. Type and size are selectable, depending on the product and throughput. At constant machine length, it is possible to choose between working width from: Tjdps Snd Nsfx Ahusf 450mm, 600mm, 900mm.

Condition: used, Year of construction: 2004, functionality: fully functional, NP 684 | COMPLETE BOTTLING LINE PET KRONES 30,000 BPH Product: Still water (with neck modification can also process sparkling) Capacity: - 30,000 BPH with 0.5L bottles - 30,000 BPH with 1.5L bottles - 22,000 BPH with 2L bottles Total working hours: 56,000 Preform Tipper M. Tanner AG: - Model: VZT-4010 - Year: 2004 Preform Washing System Krones: - Year: 2004 High Pressure Compressor Ateliers Francois: - Model: 20G282 - Year: 2004 - Pressure: 40 BAR PET Blower Krones: - Model: Contiform 20 - Year: 2004 - Number of cavities: 20 - Molds not included - Complete with preform feeder and orientator Cap Elevator and Orientator Gassner: - Year: 2004 - Supported cap types: Plastic pre-threaded cap Tjdpfxexl R Uas Ahujf - Type: Mechanical Cap Elevator and Orientator Gassner (Sport Cap): - Year: 2004 - Supported cap types: Sport cap - Type: Mechanical CIP Steinecker: - Model: Media - Year: 2004 UV Sterilization Station WEDEDCO: - Year: 2004 - Water treatment by UV rays KRONES Monoblock (filler and capper): - Model: Isofill - Year: 2004 - Rotation: Counterclockwise - Electric height adjustment Filler: - 88 valves - Filling type: Isobaric - Valve type: Mechanical - With degassing Capper: - 22 heads - Supported caps: Pre-threaded plastic; Sport Cap - Distribution: Pick & Place system Bottle Inspector Heuft: - Model: HBBVXTXXX - Year: 2015 - Bottle flow: Right to left - Inspection: Overfill, underfill, cap presence, cap misalignment Bottle Conveyors Krones: - Year: 2004 Labeller Krones: - Model: Contiroll - Year: 2019 - Rotation: Clockwise - Electric head adjustment - 18 mechanical cam heads - 1 roll-fed station - wrap-around label - Label presence control Shrink Wrapper Variopac: - Year: 2004 - Execution: Film only Wrap Around Packer Krones: - Model: Wrapapac - Year: 2004 - Hot glue system: Nordson - Packaging formats: 12x1.5L, 24x0.5L - Hours used: 1000 Bundle/Box Conveyors Krones: - Year: 2004 Handler Comag: - Model: H 55/2 - Year: 2004 - Double lane Palletizer Krones: - Model: Pressant - Year: 2004 - Package types: Bundles, boxes - Type: Push - Pallet warehouse - Interlayer system - Dual infeed Pallet Wrapper Robopac: - Model: HELIX HS 30 - Year: 2004 - Wrapping type: Rotating arm - Pre-stretch system

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, input current: 238 A, overall weight: 36,000 kg, oil tank capacity: 1,300 l, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Todpfx Asvf E Avshujf Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: new, Year of construction: 2025, Stock machine Todpfx Ahskzg Sasuef Completely redeveloped high efficiency centrifuge based on our many years of production experience with the predecessor of this centrifuge, we have made various improvements with regard to maintenance costs, downtime and wear and tear parts.

Year of construction: 2017, condition: ready for operation (used), Cutting heads: 2, cutting head type: AWJ 2D, abrasive feed: system SM4000, pump type: KMT Streamline SL-VI Standard, max. pump pressure: 3800bar. Table dimensions X/Y: 3200mm/1710mm, cutting dimensions X/Y: 3010mm/1510mm, travel range X/Y/Z: 3010mm/1510mm/250mm, travel speed: 12m/min, cutting head distance range: 90mm-450mm, positioning accuracy: +/-0.075mm, repeatability: +/-0.035mm, control: Fanuc 0i-MF, operating hours: 4866h. Includes oil cooler, water treatment, and safety zone. Documentation available. On-site inspection possible. Tedpfxexp Rcfo Ahuef

Condition: excellent (used), Year of construction: 2022, functionality: fully functional, Technical data on the EPS (Polystyrene) press: Manufacturer FZ-Recycling GmbH & Co. KG, Germany Type FZR 320 Year of construction 12/2022 Drive power shredder 4 kW Drive power of compactor screw 7.5 kW Drive power hydraulic unit for the holding clamp in the press channel 1.1 kW Total connected load 12.6 kW Current consumption 32 A Compaction ratio of the compacted blocks to the original product approx. 50:1 (depending on material) Block weight after compaction approx. 300kg/m³ (depending on material) Block dimensions 320 x 320 mm, variable length Throughput approx. 100 kg/hour, depending on material Achievable density approx. 250 - 300 kg/m³ The pressed blocks are stacked approx. 1400 mm high on pallets and stretch-wrapped. Tsdju Thkaopfx Ahuof Machine dimensions approx. 4,600 x 1,400 x 1,980 mm (l x w x h) Transport weight press 1,325 kg Condition of the baler: The press was only used sporadically, is in very good condition and available at short notice. Due to the low weight of the machine and the forklift shoes in the transport frame, the press is mobile and can be used directly on the construction site where the material is produced. The electrical connection is made via a CEE 32 A plug. Scope of delivery for the baler: 1 piece EPS press, ready for connection and use Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: new, Year of construction: 2025, In stock: Todpfxoxhf Nwj Ahujf The STF 3.0 floating sink separator with our highly efficient SP1000 Mk2 centrifuge and our VS1 water screen. A compact but powerful washing system that is low-maintenance and can wash/sort up to 3000 kg/h of hard plastics. The machines are made entirely of 304 stainless steel, so salt solutions can be used without any problems. An excellent starting point for a good homemade zinc float installation. The machines are in stock and can therefore be delivered within a week. Ask us for further information.

Condition: excellent (used), Year of construction: 2004, operating hours: 34,480 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 750 kg, overall weight: 19,000 kg, transport height: 3,300 mm, oil tank capacity: 750 l, power: 45 kW (61.18 HP), Technical data baler: Manufacturer Bollegraaf Typ HBK 100 Year of construction 2004 Hours of operation 34,480 hours Press power main press 100 tons Press power of pre-press max. 42 tons Feed channel 1,600 x 1,100 mm Filling volume 3.15 m³ Theoretic cycle time 22 sec. Theoretic throughput capacity up to 450 m³/hour Bale size 1,100 x 720 mm, lenght variable Driving motor 45 kW Connected load 60 kW Tying system 5-fold vertical, fully automatic Throughput rate at a bulk weight of 30 kg/cbm approx. 13 tons/hour bulk weight of 50 kg/cbm approx. 20 tons/hour bulk weight of 100 kg/cbm approx. 30 tons/hour Throughput rate with ruffler approx. 20 tons/hour Bale weight 550 up to 750 kg, depends on material Volume hydraulic oil tank 750 l Tedpfx Ahexbgnheujf SPS controller Telemecanique TSX Micro Transport dimensions only baler 10,900 x 2,320 x 3,300 mm (l x w x h) Machine weight baler approx. 19 tons Comments: Unlike the standard HBC press series from Bollegraaf, this machine does not have a pre-press flap but cuts the material between blades on the press ram and the counter blade in the frame. This makes it a cutting edge press, similar to a Paal, unoTech, etc. The press is in very good condition for its age, as it was used exclusively for compressing paper from document destruction. The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.