Used Plasma Profile Cutting Machine for sale (68,378)

Condition: good (used), Year of construction: 2017, V304 plate processing machine (including 1 gantry beam(s) of 6.500mm and side trucks) ◼ This V304 plate processing machine is capable of processing plates up to 3.050mm x 18.000mm for bevel plasma cutting and marking (needle marker, if attached) and 4.100 x 18.000 mm for oxy-fuel cutting and marking (needle marker, if attached) ◼ X-rail (21.000mm on both sides of the machine, including double linear guides, helical rack and pinion system and rubber covering band) ◼ Plasma cutting and extraction table (4.300mm x 18.720mm, 2 channel(s), 1 pcs, suitable for ≥ 350A cutting) ◼ Position 1: Plasma cutting unit Kjellberg SmartFocus400 (1 pcs, automatic gas console, complete with cutting parameter database) ◼ Plasma 3D bevel unit (1 pcs, including 5 NC-axis, Voortman height control, intelligent torch positioning system and 3D collision sensor, for x- ,y- , k- and v-weld preparations) ◼ Driven suspension (1 pcs, servo motor driven, including laser pointer) ◼ Dross inhibitor (1 pcs, including 1,2L reservoir) ◼ Arc Glare protection (1 pcs) ◼ Position 2: Plasma cutting unit Kjellberg SmartFocus400 (1 pcs, automatic gas console, complete with cutting parameter database) ◼ Plasma 3D bevel unit (1 pcs, including 5 NC-axis, Voortman height control, intelligent torch positioning system and 3D collision sensor, for x- ,y- , k- and v-weld preparations) ◼ Dragged suspension (1 pcs, with automatic addressing) ◼ Dross inhibitor (1 pcs, including 1,2L reservoir) ◼ Arc Glare protection (1 pcs) ◼ Position 3: Oxy-fuel cutting torch 4.0 (1 pcs, automatic gas console, ignition and piercing, complete with cutting parameter database) ◼ Voortman height control (1 pcs, capacitive height control) ◼ Dragged suspension (1 pcs, with automatic addressing) ◼ Position 4: Oxy-fuel cutting torch 4.0 (1 pcs, automatic gas console, ignition and piercing, complete with cutting parameter database) ◼ Voortman height control (1 pcs, capacitive height control) ◼ Dragged suspension (1 pcs, with automatic addressing) ◼ Position 5: Oxy-fuel cutting torch 4.0 (1 pcs, automatic gas console, ignition and piercing, complete with cutting parameter database) ◼ Voortman height control (1 pcs, capacitive height control) ◼ Dragged suspension (1 pcs, with automatic addressing) ◼ Cables high instead of low ◼ Donaldson fume extraction unit DFO 4-48 - 200L (incl. frequency controller) ◼ Air conditioning for switch panel (up to an ambient air temperature of 55°C) Hjdpfevpalaex Ampel ◼ Hardware and software (includes VACAM ‘Machine Edition’, VACAM ‘Office Edition’, VACAD editor software module, VANEST nesting software, Layout marking software module, online support) ◼ Post processor for SigmaNEST (SigmaNEST is provided by the customer) ◼ Safety devices (safety bumpers, emergency stop cord)

Condition: ready for operation (used), Year of construction: 2020, functionality: fully functional, machine/vehicle number: 286.001.911.20, working width: 3,000 mm, working length: 6,000 mm, controller model: Global Control S mit 15 Zoll Farb-Touchscreen, No minimum bid – guaranteed sale to the highest bidder! TECHNICAL DETAILS Working area: 3,000 x 6,000 mm Number of cutting torches: 2 Gas flow regulation: available MACHINE DETAILS Installation footprint: 9,000 x 5,000 x 2,000 mm Control: Global Control S with 15-inch color touchscreen Electrical Data Voltage: 3 x 400 V PE/N Frequency: 50 Hz Power: 9 kVA ATTENTION: The Zinser cutting bed is not included in the offer! EQUIPMENT according to the original invoice – details provided without guarantee Joystick and handwheel for Global Control S panel Cooling system for the control cabinet Laser diode Heat shield plate without air cooling Track for double-sided longitudinal drive HEB 9 m OmniFlow oxy-fuel supply up to 70 m³/h ALFA machine cutting torch with internal ignition SmartLifter 200 SensoMat ARKI Hsdpjyi Ub Hjfx Ampsl Full gas addressability Light barrier systems Safety device: wheel arch foot switch Energy supply via 9 m energy chain for oxy-fuel Drag chain driver Further technical data from the manufacturer – details provided without guarantee: Track gauge: 4,000 mm Chain height: 500 mm Positioning speed: 50 m/min Operating speed: max. 35 m/min Dimensions & Weight Dimensions (L x W x H): 1,940 x 5,070 x 1,980 mm Machine weight: 2,200 kg

Condition: used, Year of construction: 2012, operating hours: 7,500 h, functionality: fully functional, type of input current: three-phase, sheet thickness (max.): 35 mm, sheet thickness steel (max.): 35 mm, sheet thickness aluminum (max.): 30 mm, overall weight: 1,500 kg, input voltage: 400 V, total width: 4,000 mm, total height: 2,000 mm, total length: 8,000 mm, cutting height (max.): 110 mm, track width: 2,950 mm, Equipment: documentation/manual, Selling an Oerlikon plasma cutting system, Plasmatome 20 HPC, Nertajet HP 300 plasma source with CPM 400/450 torch heads for aluminum, steel, and stainless steel. Cutting range 2 x 6 m, cutting current 30-260 A, power consumption 80 kVA. Material thickness of the sheets to be cut with piercing up to 35 mm, external thickness up to 50 mm. Hsdpfx Aev I U Hcjmpsl Sold without cutting table.

Condition: as good as new (ex-display), The Plasma-Jet AirPro Compact 1530 Maxpro is a state-of-the-art plasma cutting machine designed for the Plasma Cutting Machines category, offering exceptional performance within the compact product group. Built for efficiency and reliability, this system features a one-piece design that ensures easy transport and rapid setup, ideal for custom and small-series manufacturing environments. With a cutting length of 3,050 mm and a width of 1,550 mm, the machine can handle substantial cutting tasks while minimizing operating costs. It comes configured with high-performance features such as a powerful MAXPRO 200 plasma source, an intuitive PULSER 3 CNC unit, and professional ProNest LT nesting software. The machine utilizes EtherCAT technology for optimal CNC performance, while the robust linear guides provide accurate, long-lasting operation. In addition, a built-in collision guard protects against damage, and a magnetic coupling allows for quick maintenance. Invest in your workshop's capabilities today by requesting a quote for the Plasma-Jet AirPro Compact 1530 Maxpro – a precise solution in the Plasma Cutting Machines product group. Hsdpfoyg Dg Tox Ampol

Condition: new, Year of construction: 2021, machine/vehicle number: XPR300-005397, type of input current: three-phase, overall weight: 680 kg, input voltage: 360 V, cutting current: 300 A, ambient temperature (max.): 40 °C, We offer this new Hypertherm XPR300 plasma cutting source, year of manufacture 2021. Only the plasma source is for sale. New, unused. 2 plasma sources available. Forklift on site. Manufacturer: Hypertherm Hjdpfoy Dqrfjx Ampjl Model: XPR300 Year of manufacture: 2021 Condition: new Category ID: 1448 Type ID: 2170 Type: plasma cutting machine If you have any questions or need further information, please send us a message or call us.

Condition: used, Year of construction: 2015, functionality: fully functional, type of input current: three-phase, sheet thickness (max.): 30 mm, input voltage: 380 V, cutting speed: 6,000 mm/min, total width: 4,850 mm, total length: 10,150 mm, table length: 6,000 mm, working width: 2,000 mm, table width: 2,000 mm, cutting current: 260 A, working length: 6,000 mm, travel distance X-axis: 6,000 mm, travel distance Y-axis: 2,000 mm, type of cooling: water, height adjustment type: electric, input frequency: 50 Hz, Equipment: double-sided, We offer this used Ajan PP15088 AUTO plasma cutting machine, year of construction 2015. Working area: 2000 x 6000 mm Machine type: PP15088 AUTO Construction year: 2015 Input voltage: 380 V Phases: 3 Frequency: 50 Hz Hjdpfx Amey Annbspel If you have any questions or need more information, feel free to send us a message or give us a call.

Condition: used, Year of construction: 2009, machine/vehicle number: 725, ECKERT plasma-gas cutting machine - JANTAR 2 Parameters: Working width 2500 mm Working length 6000 mm Hedpfjqntkijx Ampel Positioning accuracy +/- 0,005mm Thickness of plasma cutting - 35 mm Thickness of torch cutting - 120 mm Max thickness of sheet metal/cutting max 120 mm

Condition: good (used), Plasma cutting machine, plasma cutter for plasma cutting system -Manufacturer: Hypertherm, gas console for plasma cutting machine -Type: 073239 from plasma cutting machine HT2000LHF -Dimensions: 295/175/H370 mm Hsdpfswpg I Tex Ampsl -Weight: 9.9 kg

Condition: excellent (used), Year of construction: 2025, functionality: fully functional, machine/vehicle number: EN 60204-1, sheet thickness (max.): 20 mm, sheet thickness steel (max.): 20 mm, sheet thickness aluminum (max.): 10 mm, cutting height (max.): 20 mm, table length: 3,000 mm, working width: 1,500 mm, table width: 1,500 mm, warranty duration: 12 months, working length: 3,000 mm, travel distance X-axis: 3,000 mm, travel distance Y-axis: 1,500 mm, height adjustment type: electric, We are offering this well-maintained Hugong INTECUT-HT plasma cutting machine / CNC portal cutting system KAI-TEC Smart, including marking function, year of manufacture 2025, as we are upgrading to a larger system. The machine was only purchased for a single project and has been in operation since August 2025. Hsdpoyux Hqefx Ampol The manufacturer’s warranty is valid until August 2026. The system is fully functional, in excellent technical condition, and shows no signs of excessive wear. Only normal signs of use are present. It has become too small for our requirements, but it is ideally suited for smaller metal workshops, metal construction companies, or fabrication shops. Technical data & features: - CNC portal cutting system KAI-TEC Smart - Cutting area: approx. 1,500 × 3,000 mm - CNC control with cutting database - NEOCUT 105 plasma system with marking function - Plasma cutting range: 1–20 mm mild steel (stainless steel & aluminium max. 10 mm) - Machine torch including hose package - Automatic torch height control - Laser pointer - FastCam7 nesting software - DXF / DWG import - Auto-nesting function - Remnant sheet nesting - Cut cost calculation Accessories: ✅ Spare and consumable parts included (e.g. nozzles, electrodes and other accessories – ready for immediate use) Other: - Sale due to new installation - Viewing and test run possible by arrangement - Collection by buyer - Price plus VAT Legal notice: The sale is made with exclusion of liability for material defects. No warranty, no guarantee, no returns. If you have any questions or need further information, feel free to send us a message or give us a call.

Condition: used, Year of construction: 2019, functionality: fully functional, Plasma Cutting System Becky Job Master 6.20 with Extraction Table – Year 2019 This plasma cutting system is being sold due to an upgrade to a laser cutting machine. The machine is fully operational and can be inspected and tested under power. Location: Vorarlberg Technical Data Manufacturer / Model: Becky Job Master 6.20 Year of Manufacture: 2019 Working Area: 6,000 × 2,000 mm Z-Axis Travel: 300 mm Max. Cutting Speed: 75 m/min Dimensions: Machine Length: 8,000 mm Machine Width: 3,700 mm Overall Height: 2,000 mm Work Table Height: 820 mm Hjdpfxjx U Dqio Ampol All accessories belonging to the system are included, such as: Hypertherm XPR 170 power source Donaldson filtration unit Software etc. Sale excludes disassembly, transport, and installation.

Condition: used, Plasma cutting unit, plasma cutting machine MESSER GRIESHEIM Type Plasmastar HA 95 Serial No. 4040323 Year of manufacture: 1990 Power: 95 Amp. - 60% duty cycle 45 Amp. - 70% duty cycle Adjustment range: 2 steps Cutting capacity: 25 mm (clean cut) Severance cut up to 45 mm Hand torch: PHC 95/140 Power supply: 380 Volt, 50 Hz, 32 Amp. plug Hjdpeyah R Nofx Ampol - Water-cooled - New hand torch BINZEL ABICOR, Type Abiplas Cut 200 W - 6 meter hose package length - Operating manual Space requirements (L x W x H): 900 x 480 x 850 mm Weight: 160 kg Very good condition

Condition: like new (used), Year of construction: 1991, functionality: fully functional, machine/vehicle number: 176063, table length: 4,000 mm, table width: 2,000 mm, Plasma cutting machine CORTA PS 3100 Year of construction 1991/retrofit, machine number: 176063 Cutting area: 4000 x 2000 mm Hodpfx Amovfmiwepol Alternating operation of 2 cutting processes: 1x plasma cutting unit Stak Pak ll, 105 Ampere 1x oxyfuel cutting torch MG 12 SE 30 CPS control unit DNC connection Graphic base version Trajectory: 6000 mm 1 torch suspension MG 200 K arc-dependent scanning 1 plasma interlock Portal carriage, cross carriage Torch suspension MG 200 K Cutting table 4200 x 2100 x 700 mm Modular, technically advanced Stak Pak II plasma cutting system, 105 amps 1 control module CM 6032 3 power modules PM 6042 1 PCM 35 torch, 15 m 1 PCM 140 torch, 15 m 1 cooling module ex works

Condition: used, Year of construction: 2020, functionality: fully functional, type of input current: three-phase, sheet thickness steel (max.): 80 mm, table length: 6,000 mm, working width: 3,000 mm, table width: 3,000 mm, working length: 6,000 mm, travel distance X-axis: 6,000 mm, travel distance Y-axis: 3,000 mm, Equipment: documentation/manual, CNC Plasma Cutting Machine 6000x3000 mm – Messer MetalMaster Xcel 6030 – Hypertherm XPR300 – Bevel Head Hedpfxoyx Svbo Ampjl CNC Plasma Cutting Machine Messer MetalMaster Xcel 6030 General Information • Manufacturer: Messer Cutting Systems year of manufacturing 2020 • Model: MetalMaster Xcel 6030 • Machine Type: CNC Plasma Cutting Table • Condition: Used – good working condition • Availability: Immediate available Working Area • Cutting table size: approx. 6000 × 3000 mm Plasma System • Plasma power source: Hypertherm XPR300 High-definition plasma system for precise and high-speed cutting of carbon steel, stainless steel, and aluminum. Equipment / Options • Bevel cutting unit: BEVEL-R (5-axis bevel cutting system) for weld preparation and angled cuts • Software: OmniWin – programming and nesting software for optimized material usage Dust extraction system • BEUTING PFM3-9 (100 L extraction unit Machine Advantages • Robust industrial gantry construction • High precision and productivity • Bevel cutting capability for complex parts • Efficient nesting and programming via OmniWin software • Suitable for heavy steel fabrication and industrial production Applications • Structural steel fabrication • Industrial metal cutting • Manufacturing of machine components and steel constructions Additional Information Sold as it is dismantling and shipping not included. Machine can be inspected under power by appointment. Further technical details, photos, and videos available on request.

Year of construction: 2007, condition: ready for operation (used), - USED - CNC PLASMA CUTTING MACHINE WORKING AREA: 6000 x 2000 x 60 mm GENERATOR: HYPERTERM HPR130 CONTROL UNIT: GASPARINI MAX CUTTING SPEED: 0,1 - 30 m/min WEIGHT: 4400 Kg Hedpfxoyru Rgo Ampsl OVERALL DIMENSIONS: 6910 x 3150 x 1581 mm ACCESSORIES: FUME EXHAUSTER NOTE: MACHINE REVISED IN 2026

Condition: good (used), Year of construction: 2008, functionality: fully functional, Fully operational plasma cutting machine in very good condition. MicroStep PLS 7501.25PG Equipped with two torches: plasma and gas. Power source: Hypertherm, HyPerformance Plasma HPR260. Cuts mild steel and stainless steel. Table dimensions: 7.5 m x 2.5 m. The machine can be inspected under power in Vilnius. Hedpswinpxefx Ampol

Condition: new, Year of construction: 2024, functionality: fully functional, machine/vehicle number: RoboRail, type of input current: three-phase, working range: 12,500 mm, sheet thickness (max.): 20 mm, sheet thickness steel (max.): 20 mm, overall weight: 6,500 kg, input voltage: 400 V, total width: 3,200 mm, total height: 2,600 mm, total length: 20,000 mm, workpiece weight (max.): 550 kg, table length: 12,500 mm, cutting current: 125 A, working length: 12,500 mm, height adjustment type: mechanical, input frequency: 50 Hz, ambient temperature (max.): 45 °C, RoboRail: All-in-one Robot Plasma Cutting Machine We regularly hear from manufacturers that automation is not for them because everything they do is different, but that is precisely what makes automation so important! With the RoboRail, each individual part can be different and the plasma cutting machine will cut and deliver the parts 1-for-1, directly from the CAD files. Does your project require complex cuts? Send it to the RoboRail. Does your project require a wide variety of delivered profiles? Send it to the RoboRail! This machine will become the workhorse of your factory, giving you time to focus on what your company does best! Easy design input: Import files from SDS2, Tekla, or a Solid model. Or simply draw your design on the machine work surface. Optimal material usage: No more waste with HGG-optimized nesting. The more files you upload, the smarter the nesting process becomes. Seamless processing: Upload your file and RoboRail takes over. Hsdpfoq Nz Skox Ampjl Automatic loading of material and accurate determination of starting point. No need for operator intervention during the cutting process. Perfect results, every time: Get flawless cut steel, exactly matching your CAD design. Experience uninterrupted production with seamless repetition. RoboRail ensures readiness for the next production step. This machine is available in several configurations, including variants with different maximum material feed lengths. Based on your selected configuration, we can provide you with an appropriate price proposal. Please refer to our brochure for a complete listing of available options. If you have further questions, please do not hesitate to contact us!

Condition: used, Year of construction: 2004, Sato cutting machine for sale Hodpfxovx N I Ne Ampsl

Condition: ready for operation (used), Year of construction: 2011, This MicroStep EasyCut 6001.25PrGB was manufactured in 2011. It is a CNC plasma/oxyfuel cutting machine designed for industrial, heavy-duty applications. Features include a large working area of 6000 × 2500 mm, dual-side driven gantry, and compatibility with CAM software like mCAM and AsperWin. It supports up to 6 oxyfuel torches and offers options like automatic height control. Note: the gas console is defective. Contact us for more information about this machine. Application Types Hedpfxjx D Hz Hj Ampol Cutting

Condition: ready for operation (used), Year of construction: 2008, General Data Measurements width 4100 mm Measurements depth 10169 mm Machine weight 5500 kg Control Unit Brand MicroStep Model IMSNC Hodpfx Asx D Ey Iempol Main Drive Number of axis 3 This 3-axis MicroStep PLS 7501.25PG plasma cutting machine was manufactured in 2008. It features a robust MicroStep MSNC500 control system and dual cutting capabilities with a HPR 260 AGC plasma and an acetylene gas burner. The machine offers a maximum cutting thickness of 50 mm and operates efficiently within a large working field. If you are looking to get high-quality cutting capabilities, consider the MicroStep PLS 7501.25PG machine we have for sale. Contact us for more information. Application Types Cutting

Year of construction: 2010, condition: ready for operation (used), Max. sheet dimensions: 6050x2550mm, max. cutting speed: 10m/min, length: 8125mm, width: 3800mm, height: 1900mm, with documentation, an on-site inspection is possible. Hsdpfx Amori Skaopol

Condition: ready for operation (used), Year of construction: 2017, General Data Machine weight 9000 kg Measurements height 2300 mm Measurements depth 4300 mm Movement X-Axis Movement 3000 mm Y-Axis Movement 1200 mm Main Drive Number of axis 3 Dimensions Machine Length 15000 mm Hjdox D It Rjpfx Ampsl This 3-axis Hypertherm PL-YPE 3100 was manufactured in 2017 and features a Hypertherm® HyPerformance HPR 400XD gas plasma source. It offers precise cutting with a maximum capacity of 50 mm in mild steel, 75 mm in stainless steel, and 45 mm in aluminum. The effective cutting area is 3000 mm by 1200 mm. If you are looking to get high-quality cutting capabilities, consider the Hypertherm PL-YPE 3100 machine we have for sale. Contact us for more information. Application Types Cutting

Condition: ready for operation (used), Year of construction: 2015, This KOIKE PNC-12 EXTREME plasma cutting machine was manufactured in 2015. It features a robust CNC control system and an effective cutting area of 1500 x 3000 mm. Capable of handling a maximum cutting thickness of 50 mm and equipped with rapid travel speeds up to 4000 mm/min, it ensures efficient operation. Consider the opportunity to buy this KOIKE PNC-12 EXTREME plasma cutting machine. Contact us for more information about this machine. Hodpfx Ajx D Nhvjmpol Application Types Cutting

Condition: ready for operation (used), Year of construction: 2013, functionality: fully functional, working range: 6,000 mm, sheet thickness (max.): 35 mm, track width: 2,000 mm, table length: 6,000 mm, cutting current: 260 A, We offer for sale a used, reliable, fully functional Messer Multitherm eco 3100 plasma cutting machine, year of manufacture: 2013. Manufacturer: Messer Model: Messer Multitherm eco 3100 Year of manufacture: 2013 Condition: ready for use Machine type: plasma cutting machine Available for pickup: 08/2026 Description: Power source: 260 A Table size: 2 x 12 m Hedpfx Aeyvgdyjmpol Cutting up to 35 mm sheet thickness Software: Omniwin 2025 Regularly serviced Pre-prepared for oxy-fuel cutting Test run possible upon agreement If you have any questions or need more information, feel free to write us a message or call us.

Condition: ready for operation (used), Year of construction: 2013, This MGM Omnicut 3100 was manufactured in 2013. A robust plasma cutting machine, it features a 12-meter table and a powerful Kjellberg HiFocus 360i plasma source. It efficiently handles mild steel up to 80 mm, stainless steel up to 80 mm, and aluminum up to 100 mm. If you are looking to get high-quality cutting capabilities, consider the MGM Omnicut 3100 machine we have for sale. Contact us for more information. Hedpfex D Npaox Ampjl Application Types Cutting

Condition: used, Year of construction: 2020, functionality: fully functional, type of input current: three-phase, working range: 9,000 mm, sheet thickness (max.): 100 mm, overall weight: 1,100 kg, input voltage: 400 V, total width: 3,500 mm, cutting current: 154 A, input frequency: 50 Hz, We are offering this used MicroStep 9001.35P plasma cutting machine, year 2020. Type: MasterCut Hjdpfsyu Hkwjx Ampsl Model: 9001.35P Serial No.: 2815 Year of Manufacture: 2020 Rated Current: 154 A Short-Circuit Current: 6 kA Weight: 1,100 kg IP Protection: 43/20 Power Supply: 3L+N+PE AC 400/230V, 50Hz If you have any further questions or require more information, please send us a message or give us a call.