Used Hydraulic Straightening Press for sale (24,917)

Condition: used, Pneumohydraulic cylinder TOX Pressotechnik Hydro-pneumatic press, power pack Lasdpfx Aneu D Tz Ue Ueb Type: S 04.00.050.12 D No.: 208696.460 Year of manufacture approx. 2000 Pressure capacity: 4.0 tons at 10 bar Pressure capacity: 3.0 tons at 8 bar Pressure capacity: 2.6 tons at 7 bar Pressure capacity: 2.4 tons at 6 bar Pressure capacity: 2.0 ton. at 5 bar Pressure capacity: 1.6 ton. at 4 bar Pressure capacity: 1.2 tons at 3 bar Total stroke: 50 mm Power stroke: 12 mm Piston rod: Ø 30 mm Thread for piston rod: M22 x 2 mm Compressed air requirement: 3 to 10 bar - Electronic oil pressure switch with TOX digital display for force measurement, type 167282 - Height only power pack with piston rod = 610 mm - Height of power pack hydropneumatic cylinder only = 560 mm - Additional base plate 160 x 160 x 20 mm - Plunger plate: Ø 68 mm Space requirement L x W x H: 160 x 160 x 660 mm Weight: 21 kg Very good condition 3 pieces available, price per piece

Condition: used, Single-column hydraulic press MAE type S63SZ SO . 551277 Year of manufacture approx. 1977 Nominal pressing force: 63 tons Pressing force: 50 tons (practically tested) Throat depth: 320 mm Table area: 850 x 630 mm Ram area: 1050 x 500 mm Ram stroke: 500 mm Max. installation height: approx. 730 mm Table height above floor: 970 mm Hydraulic tank capacity: 600 liters Lododzp Trspfx An Ueab Drive power: 15 kW Power supply: 380 Volt, 50 Hz - Hydraulic draw cushion below the table with bores through the tabletop - Two-hand operation - Electrical control cabinet damaged Required space (L x W x H): 2000 x 1200 x 3420 mm Weight approx. 5 tons The machine is operational, the control cabinet is mechanically damaged. During test run, the machine achieves a pressing force of 50 tons, presumably a pressure relief valve is venting.

Condition: used, Single-column hydraulic press with draw cushion RÖCHER Type REP 100.01 SZ Hydraulic deep-drawing press Machine No. 15.499 Year of manufacture 2003 Pressing force: 100 tons Ram stroke: 500 mm Throat depth: 370 mm Installation height: 600 mm Table surface: 850 x 700 mm with a drop-through hole Ø 150 mm Ram surface: 700 x 600 mm Ram ejector force: 16 tons (160 kN) Ram ejector stroke: 100 mm Ram ejector with internal thread M24 x 1.5 mm Draw cushion force: 40 tons (400 kN) Draw cushion stroke: 200 mm Draw cushion area: 530 x 530 mm Pressure holding time: 0 to 90 sec. Table height above floor: 910 mm Hydraulic operating pressure: max. 300 bar Hydraulic tank capacity: 700 liters Approach speed (rapid traverse): approx. 400 mm/sec. Pressing speed up to 23.8 tons (238 kN): 5 to 68 mm/sec. Pressing speed up to 100 tons (1000 kN): 5 to 16 mm/sec. Return speed: 50 to 400 mm/sec. Main pump drive power: 18.5 kW Auxiliary pump drive power: 4 kW Power supply: 400 Volt, 50 Hz (63 Amps) - Operation and programming via PC 670 touch panel, keyboard and mouse - Machine control via SIEMENS S7-300 PLC system - Ram stroke and press force programmable via control system - Draw cushion with drawing and ejector function - Draw cushion force infinitely adjustable - Ram and draw cushion equipped with direct linear measurement system - Draw cushion can be moved in and out under the press area, for punching work using the drop-through hole - Floor-level installation, draw cushion does not penetrate the floor - Pressure and stroke cutoff - Fixed stop with indirect measurement system - Pressure holding time infinitely programmable - Table with holes for the draw cushion ram rods - Ram with ejector - Knock-out damping - Stroke triggering via two-hand operation, foot switch, hand lever and push button on the control panel Ledpfjyupuljx An Uoab - LEUZE light barrier as reach-in protection for safety operation - Front mirror columns on the press table can be shifted laterally - Electrical control cabinet mounted on machine frame - Hydraulic oil cooler with fan motor (oil-air cooling) - Manual central lubrication pump - 2x hose connections for tool tempering or cooling at the ram - Piece counter in the control system - 306 read operating hours - Operating manual, hydraulic diagram, and electrical diagram available Space requirements (L x W x H): 3100 x 1800 x 4160 mm Weight: approx. 13 tons Very good condition, as new

Condition: used, Hydraulic Synchronizing Press, Spotting Press AGEO Type GHP 200 H6 4-Column Hydraulic Press, Tool Trial Press, Spotting Press Serial No. 21169 Year of manufacture: 1993 Pressing force: 200 tons Clearance between uprights (front): 1200 mm Upright opening (side): 650 mm Laodpfjwva I Hsx An Ueb Table surface: 1560 x 1010 mm Ram surface: 1560 x 1010 mm Ram stroke: 575 mm Draw cushion stroke: 300 mm Draw cushion holding force: 63 tons Draw cushion ejector force: 30 tons Max. installation height: 775 mm Table height above floor: 1000 mm Guide column Ø: 140 mm Clamping pin bore in ram: 64 mm Pressing speed: 0 to 10 mm/s, stepless Return speed: 0 to 20 mm/s, stepless Main motor power: 22 kW Control pump motor power: 5.5 kW Connection: 400 Volts, 50 Hz - Table and ram with 22 mm T-slots - Two pressure cylinders with electronic precision synchronization control - Stepless electronic stroke limitation (top and bottom with digital travel measurement and position display) - Mechanical safety support device (prevents ram from dropping due to dead weight) - Single-hand and two-hand operation - Electrical tool safety via signal contact - Pressure presetting independent of stroke (via keypad, digital pressure display) - Travel measurement system right and left via rotary encoders - Electrical control: MS-DOS PC with Ageo H v2.23 control software - Operator panel with swiveling display - Stroke movement and press force adjustable via joystick - Adjacent hydraulic power unit with electrical cabinet - Hydraulic draw cushion under the press table - Draw cushion with ejector function - Continuous stroke control - Floor-level installation - Electrical oil temperature monitoring - Operating manual with circuit diagrams Space required by press (upright) L x W x H: 1800 x 1010 x 3470 mm Space required for horizontal transport L x W x H: 3500 x 1800 x 1200 mm Net weight press: 13 tons Space for hydraulic power unit L x W x H: 1000 x 800 x 3040 mm Net weight hydraulic power unit: approx. 1 ton The machine was used as a tool trial press in a toolmaking workshop. Very good condition.

Condition: used, High-performance baler MACFAB - BEMA type 650A Hydraulic press for packaging waste, recyclable renewable raw materials, secondary raw materials Manufacturer no. MF J0162 Year of manufacture 2021 Pressing force 50 tons. Press plate stroke approx. 1000 mm Cycle time per stroke approx. 40 sec. Pressing chamber floor area 1500 x 1100 mm Pressing chamber height 1650 mm Filling opening 1500 x 870 mm Filling height approx. 1250 mm Bale format 1500 x 1100 mm Bale height max. 1100 mm Hydraulic operating pressure 200 bar Motor power 5.5 kW Mains connection 400 volts, 50 Hz, 12 amps. - with two hydraulic cylinders - Door locking via threaded spindle with handwheel - Pressing operation only with the pressing chamber door closed - 2-hand operation for hydraulic tipping of the finished pressed bale - Free space for manual strapping - Standard industrial bales of 1500 x 1100 x 1100 mm are produced - the highly compressed bale is automatically tipped onto a pallet - only 62 operating hours Space requirement L x W x H 2120 x 1350 x 3220 mm Height for transport with lowered hydraulic cylinders approx. 260 cm Weight 1.8 ton. The machine is in very good condition, as good as new. Ljdpfx Ajvq Rtkon Usab The press has a new price of EUR 22,200 net at BEMA The BEMA company also buys the packaging waste that you press into bales with this press.

Condition: used, Hydraulic notching machine with adjustable angle SIMASV model AV 220-6PA Serial no.: C1524 Year of manufacture: 1996 Blade length: 220 mm Material thickness (steel): 6 mm Material thickness (stainless steel): 4 mm Table dimensions: 950 x 790 mm Table height: 940 mm Motor power: 3 kW Ledpfx Anerzfh Hs Uoab Power supply: 400 Volt, 50 Hz - Operation via push-button or foot switch - Adjustable notching angle from 30° to 140° - Angle adjustment via 2 handwheels (right and left) - Hydraulic clamping for the adjustable blades - Electric foot switch - 2 adjustable stop rails with angle scale - Multiple millimeter scales integrated into the table top - HSS blades newly ground, as new Required space (L x W x H): 1000 x 950 x 1470 mm Weight: 750 kg Very good condition

Condition: used, Double column hydraulic press SMG type HBP 200 - 2000 / 2000 make no. 7.4117 year of construction 1986 - rebuild 2000 pressure force 200 ton. Stand passage front 2050 mm column passage sideways 2030 mm table area 2800 x 2000 mm ram area 2000 x 2000 mm ram stroke 700 mm installation height max. 1850 mm Table height above floor 750 mm ram retraction force 33 ton. Rapid feed speed 500 mm/s Pressing speed 72/36 mm/s Return stroke speed 420 mm/s Safety distance 230 mm Motor power main motor 75 kW Motor power control pump 11 kW Mains connection 380 Volt, 50 Hz - 8-fold flat guide for the ram - Clamping plate with 22 mm T-slots at the ram, 2000 x 1900 mm, thickness 60 mm - Hydraulic ram locking at TDC - Measuring system with glass scale - Electrical control renewed in 2000 with SIEMENS SPS S7 - adjacent switch cabinet Lajdodzp Tcepfx An Ujb - 2-hand control panel adjacent - ground level installation - central lubrication - Operating instructions with circuit diagrams Space requirement of the press standing L x W x H 3700 x 2900 x 5900 mm Machine height complete with motor 5900 mm Space requirement for horizontal transport L x W x H 5900 x 3250 x 2950 mm weight 38 ton. The machine was used as a production press at Volkswagen until 2000. From 2000 the machine was used as a tool testing press in a tool shop. good condition

Condition: used, Year of construction: 2001, Amada HFE 80-25 SL Hydraulic Press Brake. S/No. VO11137 (2001), Remanufactured JTES 2018 Lasdpfx Aney D Rhyj Uob Location: These lots are located in Yeovil, UK. Please Note: There are no loading facilities on site, dismantling and loading will be at the cost of the purchaser.

Condition: used, Year of construction: 2022, Bystronic XACT Smart 160/3100 Hydraulic Press Brake. S/No. XACT 22040SE (02/2022), Max Press Force 1600KN, Max Working Length 3100mm, Max Stroke 200mm, Rapid Approach, 140mm/s, Working Speed 1 - 10mm/s, Return Speed 115mm/s, Machine Weight 10,500kg Location: These lots are located in Yeovil, UK. Please Note: There are no loading facilities on site, dismantling and loading will be at the cost of the purchaser. Laodpfx Ajy D N R Hsn Usb

Condition: used, Year of construction: 2021, Bystronic Xact Smart 225/4100 Hydraulic Press Brake. S/No. XACT21278SE (08/2021), Max Press Force 2250KN, Max Working Length 4100mm, Max Stroke 200mm, Rapid Approach 140mm/s, Working Speed 1 - 10mm/s, Return Speed 115mm/s, Machine Weight 15,000kg Location: These lots are located in Yeovil, UK. Please Note: There are no loading facilities on site, dismantling and loading will be at the cost of the purchaser. Laodoy D N Raspfx An Usb

Condition: good (used), Year of construction: 1960, Straightening and keyway slotting machines, manufacturer CARL HURTH, type: P5V, year approx. 1960. Modernized in 2018 with two-hand control. Clamping length: 1250 mm with various support dies up to 50 mm diameter. 4 dial gauge holders. Ready for use. The machine can also be used for keyway slotting. Dimensions: width 1500 mm, depth 1300 mm, height 2400 mm, weight approx. 2000 kg. Lodpfey Rgk Rjx An Usab

Condition: like new (used), Year of construction: 2026, pressing force: 20 t, For sale is a C-frame assembly and small-series production press from the manufacturer DURENDUS with a maximum pressing force of 20 tons. The machine has a table size of 700 × 920 mm, a maximum installation height of 550 mm, and a stroke of 400 mm, making it suitable for assembly work, small-series production, pressing operations, and straightening processes in industrial applications. ##### Technical data + information: C-frame assembly and small-series production press – 20 tons – 700 × 920 mm ==== General information - Design: C-frame / single-column press - Manufacturer: DURENDUS - Pressing force: 5–20 tons (adjustable) - Maximum installation height: 550 mm - Table size: 700 × 920 mm - Press head: Ø 100 mm - Table height above the ground: 1,000 mm - Overall dimensions (W x D x H): 900 × 900 × 2,340 mm - Total weight: approx. 1,200 kg - T-slots: DIN 650 – 22 mm or according to customer requirements - Forklift pockets: available - Press area lighting: available ==== Hydraulic cylinder - Stroke: 0–400 mm (adjustable) - Cylinder diameter: Ø 110 mm - Piston rod diameter: Ø 65 mm - Maximum working pressure: 280 bar - Return speed: 50 mm/s - Working speed: 10 mm/s - Idle speed: 10 mm/s - Pressure build-up time: max. 2 sec. (steel on steel) ==== Hydraulics & drive - Hydraulic pump: ASC Ledpfx Aey Sx Uwsn Ueab - Delivery rate: 24 l/min - Motor power: 3 kW - Pressure accuracy: ±5 bar - Tank volume: 60 l - Valve technology: DUPLOMATIC - Filter technology: FILTREC - Oil level monitoring: electronic - Cooling: oil-air cooling - Hydraulic unit: mounted at the top rear ==== Control system - Operation: foot pedal or hand lever - Pressure setting: via rotary control - Stroke limitation: via adjustable sensors - Selector switch: foot / hand operation - Switch cabinet components: mostly SIEMENS ==== Safety - Emergency stop switch - Stroke limitation - Stable steel construction - CE-compliant design ==== Electrical connection - Main supply: 400 V AC - Control voltage: 24 V DC - Frequency: 50 Hz - Main motor connection power: 3 kW - Total connection power: max. 5 kW ##### Application areas: Assembly work, small-series production, pressing, straightening, toolmaking, fixture construction, metalworking, maintenance, workshop operations, service applications (Hydraulic press, C-frame press, single-column press, assembly press, small-series production press, workshop press, 20-ton press, pressing press, straightening press, industrial press, C-frame press) Are you looking for a hydraulic press tailored to your specific application? Contact us for an individual offer. Our hydraulic presses are manufactured according to German Machinery Directives and European Machinery Directives (Directive 2006/42/EC), EC standards, and EU safety regulations. Furthermore, our presses exceed Canadian and European safety requirements as they meet all aspects of the national Brazilian safety regulation NR 12, which is based on these. Our strength lies in the design and construction of special machines and press automation. We distribute customized hydraulic presses at surprisingly affordable prices. The hydraulics of the presses predominantly use components from leading European manufacturers.

Condition: ready for operation (used), Year of construction: 1992, Immediately available ex location: Hydraulic single-column press Edelhoff Type HEP 45 Year of manufacture: 1992 The machine complies with the latest UVV safety regulations Press force: 45 tons Ljdpfey T Hvrsx An Uoab Table: 1000 x 1000 mm Stroke: 300 mm Drive: 7.5 kW Weight: 6 tons Price: EUR 3,000 plus VAT, ex location.

Condition: excellent (used), functionality: fully functional, Year of construction: 2020, power: 4 kW (5.44 HP), We are offering this very well-maintained Uniflex HM 325.2i_C.2_FD_MVA hose crimping machine with foot pedal, year of manufacture 2020. Model: HM 325.2i_C.2_FD_MVA Serial number: 60046 Voltage: 400 V Current: 15/8.5 A Power: 4.0 kW Frequency: 50/60 Hz Laodpfxoy Apdws An Uob Year of manufacture: 02/20 Price ex works. The machine must be collected either personally or via freight forwarding. Payment terms: 50% down payment / 50% upon collection – no cash payments! Payment by bank transfer only. Any warranty and liability are excluded. If you have any questions or require more information, please do not hesitate to send us a message.

Condition: good (used), JDS hydraulic press Bed: 505 x 510 mm Lasdpfx Ajiki Ahsn Ueb Dimensions: 140x140x285 cm LxWxH

Condition: ready for operation (used), Year of construction: 1979, Immediately available ex-location: Hydraulic high-speed press Lauffer Type EPT 25 Year of manufacture: 1979 Inspected according to UVV Press force 25 t Ljdpjy Tmuhjfx An Ujab Stroke 160 mm Installation height 320 mm Throat depth 230 mm Table 500 x 360 mm Ram 250 x 210 mm Weight 2 t Drive power 7.5 kW Price: EUR 2,750 plus VAT, ex-location.

Condition: ready for operation (used), Year of construction: 1977, Immediately available ex location: Ljdpsy Tmt Rsfx An Usab Hydraulic double-column straightening press Dunkes Type HDSR 75 Year of manufacture: 1977 Pressing force: 165 t 3 cylinders, pressing force per cylinder: 75 / 65 / 25 t Table: 1500 x 500 mm Stroke: 350 mm Drive power: 3 / 15 kW Weight: 6 t Price: EUR 2,750— plus VAT, ex location

Condition: used, Year of construction: 2000, total length: 1,000 mm, total width: 1,900 mm, total height: 2,000 mm, Colour: Grey Empty weight: 3.000 kg - Year: 2000 - Documentation available: No - CE marking present: Yes - CE certificate present: No - Serial number: 205570 - Drive system: Conventional - Press model: C-Frame press - Press force [ton]: 160 - Max. stroke [mm]: 100 - Table length [mm]: 420 - Table width [mm]: 410 - Table bore diameter [mm]: 60 - Ram length [mm]: 120 - Ram width [mm]: 120 - Transport dimensions: 1000mm x 1900mm x 2000mm (l x w x h) - Transport weight [kg]: 3000kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Laedpfx Anjy Ew Eus Ujb Lukas van Rossum

Condition: used, Double column press - Hydraulic Lasdpfx Anoudb Hco Ueb Manufacturer REPKON Model 2000/800 kN Condition used description Pressure 200 t Column width 1600 mm ram stroke - max. 600 mm Installation height 900 mm Table width 1600 mm Table depth 1300 mm Table height 1060 mm ram surface 1600 x 1300 mm T-slots Din 650 / 22H12 Rapid traverse 400 mm/s Return speed 325 mm/s Pressing speed 42 mm/s at 40% mm/sec Pressing speed 20 mm/s at 100% mm/sec Die cushion pressure 800 kN Die cushion stroke 150 mm Die cushion speed to 68/ from 225 mm/sec Conversion year: 2001

Condition: used, Year of construction: 1977, pressure 25 t throat 250 mm stroke 400 mm table surface area 600x480 mm ram surface Ø135 mm table height 980 mm weight of the machine ca. 1,5 t Lasdpoy Sliuefx An Uob dimensions of the machine ca. 2000x2000x2700 mm

Condition: good (used), Year of construction: 1970, pressure 80 t passage width 350 mm Lodpfxjvwgqre An Ueab stroke 600 mm table dimension - longitudinal 400 mm dimensions of the machine ca. 1400 x 1050 x 2350 m

Condition: used, Year of construction: 1985, pressure 40 t stroke 500 mm throat 360 mm Lsdpsy Rur Nofx An Ujab dayligth 1000 mm table surface area 630 x 500 mm table height over floor 1060 / 720 mm ram surface 450 x 360 mm feed down 60 mm/s feed up 300 mm/s power requirement 7,5 kW Weight 2,75 t dimensions of the machine ca. 1,0 x 1,8 x 3,05 mxmxm hole in the table 200 mm with oil-hydraulic drive, intermediate plate (height 340 mm) as is where is, WITHOUT putting into operation

Condition: used, Year of construction: 1989, pressure 16 t throat 200 mm stroke 160 mm dayligth 490 mm table surface area 1300 (3300) x 250 mm table height over floor 935 mm ram surface 65 mm power requirement 4,0 kW weight of the machine ca. 2,2 t required space 1,4 (5,4) x 1,3 x 2,4 m with oilhydraulic drive, shaft straightening device Lasdpfx Aoyx Ii Ren Ueb length of straightening table approx. 1300 + 2x2000 mm

Condition: used, Year of construction: 1985, pressure 100 t stroke 650 mm throat 380 mm dayligth 950 mm table surface area 800 x 700 mm Lodpfx Ajyx Ihyon Usab table height over floor 920 mm ram surface 630 x 600 mm feed down 16 - 65 mm/s feed up 375 mm/s working feed 0 - 16 mm/s oil volume 350 l power requirement 18,5 kW Weight 9,0 t dimensions of the machine ca. 1,5 x 2,5 x 4,0 mxmxm with oil-hydraulic drive, controllable dependent on pressure/time and way, speed adjustable, two-hand operation

Condition: used, Year of construction: 1975, pressure 40 t throat 280 mm stroke 160 mm dayligth 420 mm table surface area 2000 x 500 mm table height over floor 870 mm ram surface 85 mm power requirement 7,5 kW weight of the machine ca. 3,2 t Laedpjyx Ihasfx An Uob required space 1,7 x 2,0 x 2,3 m with oilhydraulic drive, shaft straightening device, manual lever control