Used Horizontal Agitator for sale (6,467)

Condition: used, Year of construction: 2007, operating hours: 20,000 h, functionality: fully functional, travel distance X-axis: 560 mm, travel distance Y-axis: 610 mm, travel distance Z-axis: 625 mm, nominal power (apparent): 49 kVA, controller manufacturer: Okuma, controller model: OSP-P200M, table width: 400 mm, table length: 400 mm, table load: 400 kg, spindle speed (min.): 50 rpm, spindle speed (max.): 15,000 rpm, operating hours of spindle: 58,000 h, coolant supply: 30 bar, spindle motor power: 22,000 W, spindle nose: SK40 Big Plus, number of spindles: 1, number of slots in tool magazine: 100, input voltage: 400 V, type of input current: three-phase, pallet changer: automatic, Equipment: chip conveyor, documentation/manual, rotational speed infinitely variable, Well-maintained 3-axis Okuma MA-400HA horizontal machining center for sale The Z-axis module requires an overhaul. If more than 30% of the maximum rapid traverse speed is selected, the axis does not move. The machine is still in daily production and can be inspected at any time. The machine is offered including: - 100 SK tool holders (without tools) included - Renishaw OMP60 measuring system incl. probe and module (for tool breakage control and tool length measurement via mechanical touch sensor) - Expanded control options (larger storage for offsets, tool corrections, axis mirroring, manual measurement, scaling up/down) - DNC-DT interface - 30 bar through-spindle coolant supply Cedpfjyvga Uex Agfegu - 6 pallets incl. fixtures for machining round parts. Smallest fixture diameter 160mm, largest fixture diameter 370mm - Mayfran Consep 2000 II chip conveyor including nonwoven-free coolant filtration system

Condition: excellent (used), Year of construction: 2021, operating hours: 500 h, functionality: fully functional, We offer this used WOLF HV 200 Horizontal Flow Wrapper / Horizontal Form-Fill-Seal Packaging Machine (food / non food), year of construction 2021. Manufacturer: WOLF Verpackungsmaschinen GmbH Type designation: HV 200 Machine number: 2690 Construction year: 2021 year Serial number: 2.21.025 Cgsdpfx Aey Tw N Njgfeu Used WOLF HV 200 horizontal flow wrapping machine in excellent condition with very low operating hours. The machine was used only for a short period during our FFP2 mask production and has therefore seen minimal wear. The WOLF HV 200 is suitable for packaging piece goods in pillow bags using heat-sealable or cold-sealable film from roll stock. It is designed for reliable, efficient and precise packaging of products in the food, non-food, medical and pharmaceutical sectors. Key highlights: very low usage, well-maintained condition, high-quality German manufacturer, suitable for individual product wrapping, immediately available. If you have any questions or need more information, feel free to send us a message or give us a call.

Condition: like new (used), Year of construction: 2017, operating hours: 10,000 h, functionality: fully functional, travel distance X-axis: 730 mm, travel distance Y-axis: 730 mm, travel distance Z-axis: 830 mm, rapid traverse X-axis: 60 m/min, rapid traverse Y-axis: 60 m/min, rapid traverse Z-axis: 60 m/min, Base Machine - SH-5000P - Demonstration Machine Like New • Basic machine, 4-axis • Control: Siemens 840D sl • Table size: 500x500mm • Max. table load: 500kg • X/Y/Z travels: 730/730/830mm • X/Y/Z rapid traverse: 60/60/60 m/min • Milling spindle: Cgsdpfx Agsy Sxg Tofsu • HSK63 • 30/50kW • 18,000 rpm • Tool magazine with 40 stations • Automatic pallet changer • Automatic loading door • Hydraulic unit • Oil separator • Oil mist extraction • Air conditioning unit for electrical cabinet • External measuring systems, linear axes • Media feed under pallets • Central lubrication • Door interlock • Coolant unit • Internal cooling with 70 bar high pressure • Coolant and compressed air gun • Chip conveyor • Documentation in German, digital

Condition: excellent (used), Year of construction: 2020, operating hours: 400 h, functionality: fully functional, machine/vehicle number: 2003031, type of input current: AC, total length: 1,670 mm, total height: 1,550 mm, total width: 1,070 mm, input voltage: 220 V, overall weight: 450 kg, film width: 370 mm, Pillow Flow Wrapping Machine – Model KFD323 (2020) High-quality pillow flow wrapping machine in good working condition, fully operational and ready for immediate use in production. Key Specifications: Model: KFD323 Year of Manufacture: 2020 Power Supply: 220 VAC Packing Speed: 15–30 bags per minute (depending on product and film) Film Width Range: 80–370 mm Features & Benefits: Cgsdpfx Agey Edgljfou Suitable for a wide range of products including food, bakery items, and general goods Consistent and reliable sealing performance Adjustable settings for speed and film width to suit different packaging needs Compact and efficient design for easy integration into existing production lines The machine has been well maintained and is ideal for businesses looking for a cost-effective packaging solution without compromising on performance. 📩 Videos, additional photos, and inspection/viewing can be arranged upon reques

Condition: excellent (used), Year of construction: 2007, BA 600-2 CNC, Horizontal Milling and Drilling Center SW Schwäbische Werkzeugmaschinen GmbH Travel: X axis: 600 mm Y axis (changeover position): 600 (975) mm Z axis: 500 mm Control: Siemens 840D control, side-mounted Feed/Rapid traverse speeds: X, Y, Z: 1 – 45,000 mm/min Max. feed force X, Y, Z: 15,000 N Average acceleration: X, Y, Z: 2.5 m/s² Measuring system: Direct measuring system X, Y, Z Spindles: Spindle speed (infinitely variable): 20–10,000 rpm Torque: 2 x 363 Nm (S6/40% duty cycle) Power: 2 x 38 kW (S6/40% duty cycle) HSK-A 100, horizontal tandem arrangement Spindle distance: 600 mm Spindle bearing diameter: 100 mm Motor spindles, liquid-cooled, AC technology Working area: Swing carrier with spur gearing, max. workpiece weight 2,000 kg Swivel time 0/180 degrees approx. 6.0 sec 2 NC rotary tables, hydraulically clamped, max. workpiece weight 700 kg, table speed 25 rpm Partition between machining and loading area Tool magazine: 2 x 50 tools HSK-A 100 chain-type magazine Tool change time (chip-to-chip): 4.48 sec Max. tool diameter: 100 mm 250 mm with adjacent slot free Max. tool length: 420 mm Csdpoy Swq Rofx Agfegu Max. tool weight: 20 kg Equipment: Central lubrication Oil minimum quantity lubrication (spindle lubrication) Chip conveyor (hinged belt conveyor) Coolant purification with compact band filter Hydraulic unit Maintenance unit Water recooler Full enclosure, crane loading possible Dimensions: approx. 5.15 x 8.50 x 4.20 m Weight: approx. 20,000 kg Year of manufacture: 2007 Other features: Very good condition Setup parallel to main time Available from December 2023/January 2024

Condition: used, Year of construction: 2010, operating hours: 9,000 h, functionality: fully functional, travel distance X-axis: 2,000 mm, travel distance Y-axis: 1,500 mm, travel distance Z-axis: 1,250 mm, rapid traverse X-axis: 30 m/min, rapid traverse Y-axis: 30 m/min, rapid traverse Z-axis: 30 m/min, Travel distances X=2000 mm, Y=1500 mm, Z=1250 mm - Siemens 840 DsL CNC control - NC rotary table for 4-sided machining, 1250 mm x 1250 mm - Horizontal spindle HSK100 - Spindle: 2500 rpm, HSK 100, 2200 Nm spindle torque - Approx. 9,500 spindle hours - Tool changer system HSK 100 / 40 stations - Chip conveyor - Internal/external air blow-off device - Minimum quantity lubrication for dry machining of castings - Full enclosure - Large interference circle 2300 mm - Double pallet changer - Short delivery time, subject to prior sale - Year of construction: 2010 Csdpfx Aey Swqwsgfjgu Coolant supply available as an option - ICS 60 bar for deep hole machining

Condition: good (used), Machine number: 2082 Type / Model: F315 Control: conventional Cgodpfxeh Rawfo Agfju travel x-y-z: 820 x 300 x 440 mm table: 1250 x 335 mm table clamping area: 1100 x 225 mm speed range: 56 to 2800 rpm spindle mounting: SK 40 Feed rate: 10 to 630 m/min rapid traverse: Connection: 6 kW Accessories/equipment: Condition: good weight: 2 t dimensions: 1700 x 2000 x 1900 mm

Condition: good (used), Year of construction: 2019, operating hours: 1,404 h, machine/vehicle number: 397, Offer 26148 Technical data: - Pressing force 420 kN / 42 t - Stroke 0 - 300 mm - Stroke speed 0 - 0.6 m/min - Tool height 200 mm - Bending capacity - with MW 125 flat prism, approx. 200 x 16 mm - with MW 240 flat prism, approx. 200 x 24 mm - Pipe bending up to 2 inches - CNC control SIEMENS SIMATIC HMI TOUCH - for angle programming + length programming Codoy Uwhbspfx Agfsgu - controlled length stop 3000 mm - various bending tools - Operating hours (read) 1404 h - Drive 400 V / 4.0 kW - Space requirement approx. W 850 x H 1250 x D 1250 mm - Weight approx. 1200 kg

Year of construction: 2020, condition: like new (used), horizontal glass washing and drying machine made in China . max. working width : 2000 mm min. glass size : 400 x 400 mm glass thikness : 3 - 25 mm working speed : 1 - 10 m/min. blower power : 15 Kw total power : 42,5 Kw brushes : 3 pairs bristle diameter of hard brush : 0,25 mm bristle diameter of soft brush : 0,08 mm brush shaft diameter : 75 mm roller diameter : 75 mm water tank : 4 units Csdpfx Agsy R Dw Isfjgu air knives : 2 table height : 900 +/- 50 mm net weight : 4300 kg machine sizes : L = 5680 mm , W : 4744 mm , H : 3287 mm

Condition: excellent (used), Year of construction: 2008, functionality: fully functional, travel distance X-axis: 560 mm, travel distance Y-axis: 610 mm, travel distance Z-axis: 625 mm, Machine type: Horizontal machining center Manufacturer: OKUMA Type: MA-400HA Year of manufacture: 2008 Control system: OSP P200M Country of origin: Japan Delivery time: short-term, by arrangement Csdpfjy Tvrvox Agfjgu 4-axis machining center, high productivity, including various accessories Machine equipment: - ConSep chip conveyor system with high-pressure pump - Various software packages - Touchsetter with length measurement and breakage detection - Work area shower Technical details: - Travels - Axes X-axis (column right-left) mm 560 Z-axis (table forward-backward) mm 625 Y-axis (spindle up-down) mm 610 B-axis 1° 0 - 360° - Number of pallets: 2 (pallet changer for 2 pallets) - Pallet size (mm): 400 x 400 - Max. pallet load capacity (kg): 400 - Max. pallet workpiece dimensions (mm): 500/600 x 710 - Spindle speed (rpm): 15,000 - Main spindle (10min/cont): 22/18.5 kW - Tool holder: BT40 - Tool magazine: 60 positions Optional: - Transport organization and execution - Machine delivery and installation - Machine commissioning

Condition: used, Year of construction: 2023, Exhibition machine Garbsen HORIZONTAL PANEL SAW GABBIANI P Manufacturer: SCM Type: GABBIANI P80 Year of manufacture: 2023 1 unit MAIN FEATURES INDIVIDUALLY SELECTABLE AIR CUSHION TABLES: AN INDISPENSABLE TOOL SIDE SAFETY DEVICES: MORE SPACE FOR WORKING FLOATING GRIPPERS: GUARANTEED PERFECT CUT TECHNICAL DATA GENERAL INFORMATION gabbiani p80 Saw blade projection mm 80 Working table height mm 950 Standard number of grippers 5 Number of grippers for versions 33/38/43 9 / 10 / 10 Number of grippers for versions 33/38/43 with FlexCut 1 unit (single gripper with double fingers included) 10 / 11 / 11 CUTTING DIMENSIONS Version 33 mm 3300x2100 Version 33 (Opt.) mm 3300x3200 Version 38 mm 3800x3200 Version 38 (Opt.) mm 3800x3800 Version 43 mm 4300x3200 Version 43 (Opt.) mm 4300x4300 AXIS SPEED Variable saw carriage speed m/min 6 – 60 Variable pusher speed () m/min 60 MAIN SAW BLADE Motor power (S6 -40%) - 50hz (star-delta start) kW (HP) 7 (9) (11) Speed – 50 hz rpm 4650 Saw blade diameter mm 340 Shaft diameter main saw blade mm 80 SCORING BLADE Motor power (S6 -40%) - 50hz kW (HP) 1.5 (2) Speed – 50 hz rpm 5850 Scoring blade diameter mm 200 Shaft diameter scoring blade mm 80 INSTALLATION Installed power kW 12÷15 Base machine voltage Euro voltage (400 V / 50 hz) Compressed air demand NL/min 300 Required compressed air pressure bar 7 Extraction air requirement m3/h 2440 Extraction air speed m/sec 20 Extraction port diameter mm 4x120 () Note: in countries where EU standards apply, the forward pusher feed speed is limited to 25 m/min. GENERAL CHARACTERISTICS Fully automatic, PC/PLC-controlled horizontal panel saw suitable for cutting solid wood, MDF, chipboard, plywood, and similar materials. Frame and working table – Machine frame is a steel tube construction – Working table of rib-reinforced steel with Bakelite coating – Longitudinal fence on the left side Saw carriage made of steel, consisting of: – a motor for the main saw blade and a motor for the scoring blade – vertical lifting of the saw blade on linear ball bearing guides and shoes – running rollers of hardened and ground steel – balanced mass distribution for optimal cut quality – running direction towards the longitudinal fence – saw carriage drive via rack and pinion – carriage travel on cylinder guides – cylinder guides of hardened and ground steel (5-year warranty), protected by special dust wipers – pneumatic switch for fast and safe main and scoring blade change Pressure beam – pressure beam with uniform pressure across the entire cut length, recesses to prevent collision with grippers; pneumatic height adjustment via high-precision rack and pinion, pressure adjustable from 1.5 to 6 bar – dual extraction system with one unit above the pressure beam for cleaning the work table and one unit below on the saw carriage – side automatic aligner with pneumatic cylinder over the entire length. Sliding on linear ball bearing guides and shoes. * Travel distance: 1200 mm * minimum working width: 60 mm * maximum working width: 1200 mm Positioning pusher and rear part of the machine – Positioning pusher full length, powered by a robust drive shaft. Positioning pusher control... Codpfxsx Twcve Agfegu

Condition: used, Year of construction: 1991, total length: 10,730 mm, total width: 1,600 mm, total height: 2,400 mm, Colour: Green Empty weight: 12.000 kg Price: On request - Year: 1991 - Documentation available: No Cedpfjy E Imvjx Agfegu - CE certificate present: No - Serial number: 0443848 - Drive system: Conventional - Power [kW]: 30.0 - Centre height [mm]: 625 - Swing over bed [mm]: 1250 - Carriage turning diameter [mm]: 1100 - Distance between centres [mm]: 8000 - Bed width [mm]: 800 - Spindle bore [mm]: 1100 - Min. spindle speed [rpm]: 1.8 - Max. spindle speed [rpm]: 355 - Options: Fixed steady, Four-jaw chuck, Three-jaw chuck - Transport dimensions: 10730mm x 1600mm x 2400mm (l x w x h) - Transport weight [kg]: 12000kg - Transport packages [pcs.]: 3 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, Year of construction: 1999, Technical details: x-travel: 630 mm y-travel: 630 mm z-travel: 630 mm control: Unipro 90 Pallet changer 2x: 400 x 500 workpiece - installed height: 800 mm max. clampable workpiece diameter: 720 - 850 mm Cjdoy Rmk Rjpfx Agfogu spindle taper:: SK 40 spindle turning speed - stepless: 10 - 8000 1/min Spindle power: 20 / 30 kW Spindle Torque: 95/143 Nm tool magazin:: 80 SK 40 total power requirement: 55 kW weight of the machine ca.: 11 t Machine with Unipro 90 control for 5 axis - twin palette changer - tool magazine 80 HSK-A 63 - coolant device with coolant through spindle 7 pressure levels - full A & B-axis - chip conveyor *

Condition: good (used), Year of construction: 2011, travel distance X-axis: 1,200 mm, travel distance Y-axis: 950 mm, travel distance Z-axis: 1,200 mm, Travel path B: 0-360° Travel path A: +45° to -90° Cgodjza Dzwopfx Agfsu Spindle interface: HSK 100 Rotary spindle diameter: 200 mm Spindle speed: 15,000 rpm Chain magazine: 60 positions Pallet changer Chip conveyor High-pressure coolant through spindle Coolant filtration system

Condition: good (used), Year of construction: 2011, travel distance X-axis: 650 mm, travel distance Y-axis: 650 mm, travel distance Z-axis: 680 mm, Tool holder: HSK 63 Turning spindle: 85 Spindle speeds: 20,000 rpm Chain magazine: 60 positions Chip conveyor Pallet changer Codpfx Ajza Drvogfegu Coolant filter unit High-pressure coolant through spindle

Condition: good (used), Year of construction: 2018, 15 out of 17 units of low-lift pallet trucks, horizontal order pickers 2.5t, Jungheinrich ECE 220/225, – used –: Price per unit, ex warehouse: now only €1,950 instead of €2,950 (net)! Price with operating hours up to 3,000h = per unit, ex warehouse: now only €2,950 instead of €3,750 (net)! Manufacturer: Jungheinrich Type: ECE 220/225 Year of manufacture: 2018 Maximum lift height: 125 mm Overall length: 3,670 mm Width: approx. 810 mm Fork length: approx. 3,670 mm Fork dimensions: 60 x 172 x 2400 mm Voltage: 24 V Travel speed: 12.5 km/h Working aisle width (pallet 800x1200 lengthwise): 3,870 mm Lifting speed without load: 0.1 m/s Operating hours: see list, as of January 2026 – a few hours have been added in the meantime Incl. battery charger Weight incl. battery: approx. 1,000 kg Condition: good Available: immediately Location: warehouse Frankenberg / Saxony Positions: 9 / 35 / 29 / 7 / 4 / 19 / 3 / 41 / 25 / 42 / 24 / 34 / 28 / 43 / 30 / 32 / 26 Further photos of the other units available upon request! Operating hours: 1/26 Year of manufacture ECE02L 90548594 Low-lift pallet truck - KMS ECE 220/225 1,938 2018/2 ECE03L 90548595 Low-lift pallet truck - KMS ECE 220/225 3,362 2018/2 ECE05L 90548597 Low-lift pallet truck - KMS ECE 220/225 3,241 2018/2 Cgedpfx Agoyrriasfeu ECE06L 90548598 Low-lift pallet truck - KMS ECE 220/225 2,313 2018/2 ECE01L 90548593 Low-lift pallet truck - KMS ECE 220/225 3,465 2018/3 ECE04L 90548596 Low-lift pallet truck - KMS ECE 220/225 3,310 2018/3 ECE07L 90548599 Low-lift pallet truck - KMS ECE 220/225 3,456 2018/3 ECE08L 90548600 Low-lift pallet truck - KMS ECE 220/225 3,180 2018/3 ECE11 90569520 Low-lift pallet truck - KMS ECE 220/225 4,777 2018/11 ECE13 90569522 Low-lift pallet truck - KMS ECE 220/225 3,901 2018/11 ECE14 90569523 Low-lift pallet truck - KMS ECE 220/225 2,796 2018/11 ECE20 90569529 Low-lift pallet truck - KMS ECE 220/225 4,035 2018/11 ECE22 90569531 Low-lift pallet truck - KMS ECE 220/225 4,503 2018/11 ECE24 90569539 Low-lift pallet truck - KMS ECE 220/225 4,925 2018/11 ECE26 90569535 Low-lift pallet truck - KMS ECE 220/225 4,579 2018/11 ECE28 90569533 Low-lift pallet truck - KMS ECE 220/225 3,825 2018/11 ECE30 90569541 Low-lift pallet truck - KMS ECE 220/225 3,831 2018/11

Condition: new, Year of construction: 2026, neu 2026 060214 prompt, Zwischenverkauf v Türkei 7700 € 148.61 € 1 Schwenkrahmen 2730x27x0,9 mm 35/70 m/min 230 mm 230 mm 320x130 mm rund 210 mm, quadrat 190 rund 130 mm, quadrat 100 rund 180 mm, quadrat 150 805 mm Codpfx Agewirybsfogu 0.37 kW 1.3 kW 0.12 kW 1350 mm 700 mm 1300 mm 430 kg swivel frame infinitely adjustable lowering with hydraulic cylinder hydraulic lifting of the saw frame mechanical vice with quick clamping coolant equipment machine base chip collecting tray user manual in GERMAN or ENGLISH OPTIONS: Roller tables and band saw blades on request

Condition: new, Year of construction: 2026, neu 2026 060215 prompt, Zwischenverkauf v Türkei 9280 € 179.1 € 1 Schwenkrahmen 3160x27x0,9 mm 20-100 m/min 270 mm 270 mm 340x220 mm rund 230 mm, quadratisch rund 150 mm, quadratisch Cgedswirktspfx Agfsu rund 180 mm, quadratisch 910 mm 0.37 kW 1.5 kW 0.12 kW 1730 mm 770 mm 1460 mm 476 kg DIGITAL ANGLE READ OUT blade brush control panel swivel frame infinitely adjustable lowering with hydraulic cylinder hydraulic lifting of the saw frame quick lowering with automatic switchover to working speed using a sensor pin mech. Vice with quick clamping coolant equipment machine base chip collecting tray user manualin GERMAN or ENGLISH OPTIONS: Roller tables and band saw blades on request

Condition: new, Year of construction: 2026, neu 2026 060216 prompt, Zwischenverkauf v Türkei 20700 € 397.44 € 1 Schwenkrahmen 5200x34x1,1 mm 20-100 m/min 440 mm 440 mm 610x440 mm rund 410 mm, quadrat 410 rund 320 mm, quadrat 250 rund 410 mm, quadrat 410 rund 320 mm, quadrat 285 860 mm 0.55 kW 3 kW 0.12 kW 2800 mm 1210 mm Cgsdjwiqtyepfx Agfju 1870 mm 1540 kg hydraulic vice digital readout for scale of bending angle hydraulic clamping of sawing arm turning of sawing arm by hand continuously variable down speed of sawing arm automatic sawing frame lifting after cutting sensitive cutting pressure adjustment subject to material condition hydromechanic tape tension readout by manometer mobile control panel angular geared conical heavy duty gear unit driven chip brush tape guiding by hard metal sheet plates and rolls automatic tape break lock HYDRAULIC UPLIFT OF SAWING FRAME user manual in GERMAN or ENGLISH OPTIONS: Roller tables and band saw blades on request

Condition: like new (used), Technical data: Applications: Straightening and bending of steel beams, steel plates, pipes, welded structures, etc. Electric control Working speed hydraulically adjustable Pressing force: 200 tons Table size: 700 x 700 mm Cgjdey S U Umspfx Agfeu Tool height: 600 mm Straightening ram height: 600 mm Stroke length: 0 - 550 mm Bending speed: 0 – 0.6 m/min. Motor power: 18.5 kW CE marking Weight: approx. 12.5 tons Accessories: Straightening beam with support: 5200 mm Condition: Very good, almost new condition The seller is not liable for typing or data transmission errors. The machine’s appearance, technology, and wear are consistent with its age; used machines are sold without any warranty.

Condition: used, Year of construction: 2014, Technical details: x-travel: 760 mm y-travel: 760 mm z-travel: 760 mm total power requirement: 43 kW weight of the machine ca.: 11,5 t Cjdsxrwpdepfx Agfegu dimensions of the machine ca.: 2,7 x 4,73 x 2,87 m max. table loading capacity: 500 kg

Condition: excellent (used), Year of construction: 2006, Heller MCH 250 4 axes Year of manufacture: 2006 Control: Siemens 840 D Spindle speed: 12,500 rpm Travel distances: X: 800 mm Y: 800 mm Z: 800 mm Pallet size: 630 x 630 mm Cgjdpfx Agsy Nyckofou Max. tool length: 600 mm

Condition: excellent (used), Year of construction: 2006, Heller MCH 280 C 5 axes Year of manufacture: 2006 Control: Siemens 840 D Spindle speed: 8000 rpm Travel paths X: 1000 mm Y: 1200 mm Cgodpey Nybgsfx Agfju Z: 1100 mm Pallet size: 630 x 630 mm Rotary table: 360,000° x 0.001° Tool magazine positions: 400 Interface: HSK 100

Condition: excellent (used), Catalogue number 7787 TECHNICAL SPECIFICATIONS - Tool diameter: 14mm - Maximum drilling depth: 170mm - Maximum milling length: 180mm - Adjustment of drilling apparatus front/rear - Table adjustment up/down and sideways - Table swivel angle: +/-20˚ - Working table dimensions: 620x280mm - Material clamping - Motor power: 1.5kW Cgsdpfezabakox Agfeu - Brake - Dimensions (L/W/H): 1070x660x1250mm - Weight: 300kg ADVANTAGES – Polish production – Very good condition – Used drilling machine Net price: 5900 PLN Net price: 1400 EUR Net price calculated at an exchange rate of 4.2 PLN/EUR (In the case of major exchange rate fluctuations, the price may change)

Condition: good (used), Year of construction: 2005, functionality: fully functional, Toyoda FH 550, Year of manufacture 2005, Fanuc 31i MA control system, Travel range X/Y/Z 750/800/850 mm, Pallet size 550 x 500 mm, Spindle speed up to 15,000 rpm, Cjdpfxjy S Rp Ts Agfsgu 60-tool automatic tool changer, BT 40, Coolant system, 70 bar, Chip conveyor.