Bandsaw - Horizontal

BERG & SCHMID GBS 305 AutoCut

Condition: new, cutting diameter 280 mm saw band length 3370 mm Kedpfx Asivuqtsa Eefa cutting width 350 mm dimensions of saw-band 3370 x 27 x 0,9 mm 280 mm 250 mm 350 x 200 mm 240 mm 220 mm 230 x 220 mm 170 mm 150 mm 170 x 100 mm saw tape speed 37 + 74 m/min total power requirement 1,8 kW weight of the machine ca. 0,6 t dimensions of the machine ca. 1,5 x 1,7 x 2,0 m

Condition: as good as new (ex-display), Year of construction: 2023, air pressure: 5.9 bar, Next-generation air plasma system that significantly simplifies system operation for cutting and gouging up to 32 mm. Features automated process setup using advanced RFID-enabled SmartSYNC torch and a revolutionary one-piece consumable cartridge that provides traceable usage data. Technical data: Cutting performance: Recommended cutting capacity: 32 mm - 500 mm/min Maximum cutting capacity: 38 mm - 250 mm/min Severance capacity: 50 mm - 125 mm/min Piercing: 22 mm Typical gouging: Metal removal rate: 8.6 kg per hour Gouge profile: 6.6 mm (D) x 6.0 mm (W) Kfodpfxow U Stqe Aa Eja Scope of delivery: Power cable, H105 handheld torch 23 m, 75° Workpiece lead with clamp, Operating manual Option: Hypertherm cartridge reader, software

Condition: new, capacity 90 degrees: round 305 mm capacity 90 degrees: square 260 mm Kfsdonq Sanopfx Aa Eja 350 x 200 saw band length 3375 x 27 x 0,9 mm band speed 18 - 110 m/min table height 940 mm total power requirement 1,5/1,8 kW weight of the machine ca. 0,61 t dimensions of the machine ca. 1,5 x 1,75 x 1,9 m Double miter metal band saw with AutoCut function - Miter cuts up to 60° left and 45° right - Ball bearing turntable - Vice can be moved sideways - Massive, large material support - Automatic cooling Figure is semi-automatic.

Condition: ready for operation (used), functionality: fully functional, HURON NU-4 is equipped with several buttons, switches and levers to control its operations. x-travel: 1100 mm y-travel: 700 mm z-travel: 500 mm spindle/table distance: 9-509 mm spindle head - swivelling: 360°. spindle taper: SK 40 Meziv spindle speed range: 30 - 2066 rpm spindle speed steps: 27 feed rates: 1.6 - 820 mm/min feed steps: 27 table surface: 1435 x 460 mm rapid traverse on X and Y axes: 2.8 m/min rapid traverse on Z axis: 1.4 m/min total power requirement: 10 PS(HP) weight of the machine approx.: 3.1 t Kjdpforiulgjx Aa Eefa dimensions of the machine approx.: 2.36 x 1.65 x 1.45 m (w x h x d)

Condition: reconditioned (used), Year of construction: 2002, Universal tool milling machine Make: KUNZMANN Model: WF 4/3 Year of manufacture: 2002 - partially overhauled, newly painted, RAL7035 light gray / RAL3027 raspberry red RAL7016 anthracite gray Mach. no.: 344025 with guarantee geometric acceptance with test report Accessories: - HEIDENHAIN TNC 124 path control - HEIDENHAIN HR 410 electronic handwheel - HEIDENHAIN KT 130 electronic 3D touch probe system Kfodpfxem Nbwts Aa Esa for recording the workpiece position for determining workpiece reference points for measuring a finished part incl. Weldon chuck SK40/Ø 16 mm - universal table 650 x 395 mm (T-slot: 14 mm) can be swiveled around 3 axes can be rotated 360° (as 4th axis digital displayed in the control) pivotable +/- 30° tilting range towards the machine 45° tilting range away from the machine 15° centering hole Ø 32 mm table load 150 kg - vertical milling head SK 40 with hydraulic tightening system DIN 69872 - central lubrication, electric - coolant system - splash guard cabin, travelling, electrically secured - operating instructions used as seen The machine is technically corresponding to the state of the year it was built.

Year of construction: 2024, condition: new, Working space 1100 x 660 x 816 mm (W x D x H) Blasting chamber Dust-tight vacuum cabin in stable sheet steel construction Working gloves special rubber, wear resistant, cotton inside, firmly connected to the cabin against dust leakage Doors Blasting chamber W x D x H = 1100 x 660 x 816 mm Two side doors, dust-tight closing, double-walled, sound-absorbing foam, lockable, with electrical shut-off safety device Blasting media recovery Via coordinated MHG recovery system Operation ON/OFF switch for suction and lighting, pressure regulator, manometer and foot switch Viewing panels Kfodpfxoh Hxubs Aa Eja

Condition: new, Year of construction: 2025, Exhibit available immediately: New Kaeser SK 25 T - 10 bar screw compressor with integrated cold dryer Pressure: 10 bar Kfedpfedrc Txsx Aa Eea Nominal power: 15 kW Delivery rate: 2.11m³ / min Sound level: 67 dB (A) Compressed air outlet: 1 " Dimensions length x width x height: 750 x 1240 x 1260 mm Weight: 395 kg Operating hours: 0 Visit our store. We always have a large selection of new and used compressors in stock!

Condition: new, Model Name Shark 281 SXI evo Kfodogvkgljpfx Aa Esa

Condition: used, machine/vehicle number: 76271002, sheet width:2040 mm plate thickness:1,2 mm total power requirement:2,5 kW weight of the machine ca.:2,0 t dimensions of the machine ca.:3,0 x 1,6 x 1,7 m Kfodpjcxxq Esfx Aa Eea

Condition: new, capacity 90 degrees: round 350 mm capacity 90 degrees: square 330 mm 450x320 saw band length 4250x34x1,1 mm band speed 40 + 80 m/min table height 845 mm saw band width 34 mm total power requirement 2,2 kW weight of the machine ca. 0,985 t dimensions of the machine ca. 1,4 x 2,0 x 2,2 m Double miter band saw, hydraulic semi-automatic, DGS 350/450 HA-I · miter left + right 60° without machine conversion · 34 mm saw blade width · Large material support turntable, ball bearings · To position the saw blade guides using a very wide linear guide · Strong, robust transmission · Large chipboards · Infeed and outfeed roller Removable chip tray (disinfection) · Free-standing control panel, safe and ergonomic · Storage space for tapes, consumables · Cutting pressure regulator Feed regulator · Fully hydraulic vise Kodpjfgyicofx Aa Ejfa Preload super fast (front loading) · Material height sensor (automatic cut start detection) Semi-automatic function: 1. Clamp material 2. Saw starts 3. Rapid lowering to the start of the material or the same for series cutting cut 4. Saw band off 5. Raise the frame to just above the material 6. Open the vise Optimum, material-independent cutting result through fine adjustment of the saw frame by means of: *Pressure Control Valve (Cutting Pressure Force) *Feed Control Valve (Speed) *Switch with pictogram, easy and clear to use