Used Homag Bmg for sale (485)

Condition: used, machine/vehicle number: 008648, Max. working width: 1300 mm Max. working thickness: 60 mm Nledezmmulepfx Ahfsf Number of painting guns: 4

Condition: reconditioned (used), functionality: fully functional, Flat- or glue joint scraping unit Nodpfxstywuks Ahfjlf Used unit, not reconditioned, without warranty - For removing of glue residuals or leavings from the panel surface in the area of the glue joint. Specification: - consisting of one top and one bottom unit, individually adjustable. - top unit synchronized with top pressure in vertical direction - version with 3 small tracer rollers, individually adjustable, for smooth passage at front and rear edge of panel. IMPORTANT ANNOTATION: version with pneumatic cylinders for lateral cut-in/out controlled by selection of the individual unit in the main control is currently not available. But it is possible to retrofit this feature. Please ask for our quote. Installation and set-up of the unit at your machine is also possible.

Condition: reconditioned (used), functionality: fully functional, Universal Trimming Unit UF11, with frequency inverter Used & reconditioned unit, without warranty For grooving or rebating in edgebanding machines or double end tenoners Specification: - motor can be swiveled steplessly or in rasters from +90 to -90 degrees (each vertical position of motor shaft) - motor 4 kW, 3Ph 400 V, 300 Hz - motor shaft diameter 30 mm - with electro-pneumatic jumping function - inclusive of suitable KEB frequency inverter (used & tested) Upon request the unit can be upgraded to motorised Njdpoztl Rxjfx Ahfjlf (NC-controlled) adjustments in x- or y-axis. Please ask for our quote. Installation and set-up of the unit at your machine is also possible. Availability 1 - 2 weeks after receipt of order.

Condition: ready for operation (used), Year of construction: 2009, functionality: fully functional, HOMAG Pre-melting unit for Quick-Melt system Nledpfx Ahoztl Nbofof

Condition: ready for operation (used), Year of construction: 2011, functionality: fully functional, operating hours: 1,651 h, workpiece height (max.): 60 mm, edge thickness (max.): 3 mm, feed rate X-axis: 25 m/min, HOMAG KAL 310 + panel return system TFU 140! TECHNICAL DETAILS Profile milling unit FK11 manual Edge thickness: max. 3 mm Motors: 2 units Motor power: 0.4 kW per motor Frequency: 200 Hz Speed: 12,000 rpm Feed speed: max. 20 m/min Feed speed for continuous trimming without profile trimming: max. 30 m/min Panel length single-sided: min. 240 mm Panel length double-sided: min. 120 mm Panel thickness: 12 - 60 mm Panel spacing with PC22: min. 500 mm Minimum workpiece gap for workpiece thickness over 22 mm: min. 600 mm Multi-scraper MN21 Automatic Number of profiles: max. 5 different profiles Edge thickness: max. 3 mm Panel thickness for radius R = 3 mm: min. 13 mm Panel thickness for bevel 0.5 x 45°: min. 10 mm TC knives: 2 units Bevel angle: 20° Radius: R = 1.5 / R = 2 / R = 3 / R = 5 Pre-milling unit BF10 Motors: 2 units Motor power: 0.55 kW per motor Frequency: 200 Hz Speed: 12,000 rpm Nsdpfx Aeyzxa Eshfjlf Swivel range: +/- 1° TC cutter: 70 x 25 mm HSK: 25 Cutting angle: 54° Feed speed: 18-25 m/min Workpiece thickness: 8-60 mm Edging material (roll): 0.3-3 mm MACHINE DETAILS Operating hours Operating hours: 6,358 h Feed time: 1,651 h EQUIPMENT Pre-milling Automatic adjustment of the infeed fence Infeed device with 2 rollers Quickmelt application station 2-roller magazine infeed Automatic adjustment of the pressure zone HL84 end trimming unit with pneumatic adjustment BF10 flush milling unit with pneumatic adjustment FK11 profile milling unit MN21 multi-profile scraper unit for 5 different profiles Grooving unit Glue joint scraper Buffer Return system TFU140

Condition: used, machine/vehicle number: 008479, Max. machining width: 1650 mm Min. machining thickness: 3 mm Working Table: Fixed pass height No. Operating units: 4 Nr Nodsy Edqwjpfx Ahfjlf

Condition: excellent (used), Numerical Control Type Power Control PC85T Software WoodWOP + TOPDRILL No. 2 Through-feed motorized conveyoring belts No. 2 Horizontal units/supports (with Digital quota/axes display) No. 1 Drilling head for each horizontal unit (1 x Kw 1,5) No. 21 Splindles for each horizontal drilling head Max. working width (mm) 2500 Min. working width (mm) 250 Nodpfx Aozrd Sfshfolf No. 4 Bottom vertical units/supports (with Digital quota/axes display) No. 2 Drilling heads/blocks for each bottom vertical unit (2 x Kw 1,5) No. 4 Vertical top pressure clamps Motorized carpet to evacuate chips and wastes Total installed power (Kw) 35

Condition: excellent (used), Double side - Independent Machine (or 1st and/or 2nd in a line) Edges (band in rolls) thickness (Min/Max) mm 0,3 / 3 Panels thickness (min/max) mm 12 - 40 Working width (min/max) mm 250 / 2500 Numerical Control /Software Power Control 22 / woodCommander Nlsdpfx Ahszrd Rzjfef Adjustable feeding speed (m/min) 15 - 35 Safety and sound-proof enclosures/cabins Distance (center-axes) of the Disappearing Dogs (mm) 1000 SIZING PART (for each side): Spraying unit (Anti-sticking liquid) Anti-chipping Milling Unit (1 x Kw 4,5) Hogging Units KD 11 (2 x Kw 6,6) EDGE-BANDING PART (for each side): Glueing Unit (Hot Melt + Quick Melt Unit) A3 Pressure zone A Edge coils supporting unit (No. 2 of reels) with servo-assisted edge feeding Snipping Unit HL86 (2 x Kw 0,22) Rough Trimming Unit BF10 (2 x Kw 0,55) Fine Trimming Unit PF20 (2 x Kw 0,4) FRRE SPACE for Corner Rounding unit ( Contour Trimming) FF 12 (2 x Kw 0,4) Profile Scraping unit PN 10 Finish processing unit (Glue scraper + Buffing unit) FA 11 Spraying Unit (for polishing liquid)

Condition: excellent (used), Double side - First (1st) machine in a line Machine Edges (band in rolls) thickness (Min/Max) mm 0,3 / 3 Panels thickness (min/max) mm 12 - 40 Working width (min/max) mm 195 / 1500 Numerical Control /Software Power Control 22 / woodCommander Adjustable feeding speed (m/min) 15 - 32 Safety and sound-proof enclosures/cabins SIZING PART (for each side): Spraying unit (Anti-sticking liquid) Hogging Units KD 10 (2 x Kw 6,6) EDGE-BANDING PART (for each side): Nodezrd Nqopfx Ahfolf Glueing Unit (Hot Melt + Quick Melt Unit) A3 Pressure zone A Edge coils supporting unit (No. 2 of reels) with servo-assisted edge feeding Rough Trimming unit BF10 (2 x Kw 0,55) Fine Trimming unit PF20 (2 x Kw 0,4) FRRE SPACE Milling grooving unit UF 11 (1 x Kw ?) Profile Scraping unit PN 10 Finish processing unit (Glue scraper + Buffing unit) FA 11 Spraying Unit (for polishing liquid)

Condition: as good as new (ex-display), 4-SIDE EDGE BANDING LINE + DRILLING Workpieces dimensions: min. mm 195 x 250 x 60 / max. mm 1200 x 2500 x 60 Composed of the following machines: Njdpfxszrd Dhs Ahfelf 202005a) 1st Double-side Sizing & Edge Banding machine "HOMAG" Mod. KFL 325/ M1 / C 202005b) Turning Station "HOMAG" Mod. TDL (from lengthwise to crosswise) 202005c) 2nd Double-side Sizing & Edge Banding "HOMAG" Mod. KFL 326/ M2 / C 202005d) Connecting Roller Conveyor 202005e) Automatic (through-feed) Multi Borer "WEEKE" Mod. BST 503

Condition: excellent (used), Year of construction: 2023, machine/vehicle number: 0-200-87-0913, functionality: fully functional, input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, edge thickness (max.): 3 mm, height adjustment type: electric, total length: 10,825 mm, Equipment: documentation/manual, Used single-sided HOMAG edge-banding machine for straight edges – EDGETEQ S-500 For pre-milling (jointing trimming), gluing and post-processing of various kinds of edging materials. Fixed stop on the left side. Year of Manufacture: 2023 EQUIPMENT / SPECIFICATION BASIC MACHINE - with 80 mm wide conveyor chain with rubber-coated chain pads, - workpiece thickness 8 to 60 mm - top pressure with compound V-belt, automatic height adjustment (to workpiece thickness) - panel support with roller guide, extractable approx. 700 mm - glue roller drive in case of feed stop - hand switch /remote control for setup – mode - adjustable infeed fence with NC-axis (CAN-bus) - Jointing trimming 2 motors each 3 kW (clockwise, counterclockwise), jumping function GLUING SECTION V20, consisting of: - QA65 glue application unit, with PTFE-coating (Teflon), with pneumatically operated glue gates - pneumatic clamping of glue application - Pre-melter for PUR glues - Edge magazine, edge thickness min. 0,4 mm to max. 3 mm Edge width (height) max 65 mm - 2-fold automatic edge roll changing magazine - Pressure zone with automatic horizontal adjustment (NC CAN-axis) to edge thickness, 1 driven & 4 non-driven pressure rollers. POST-PROCESSING SECTION: - Snipping (end-trimming) unit PK25 horizontal, 2 motors, with straight/chamfer cutting function - Edge Trimming MS40 2x0.55 kW, top/bottom - Multifunction Corner Rounding MF60, 2 motors 0.4 kW (top/bottom) with linear motors, soft-touch - Profile (radius-) Scraping MN11, multi scraping tool, automatic positioning and adjustment (NC) - Flat Scraping (glue joint) FA20, top/bottom, (version with 3 tracer rollers), automatic adjustment - Buffing Unit FP10, top/bottom Nsdeztpw Nepfx Ahfjlf Control / software: - powerControl PC 23 PowerTouch - woodCommander 5 - Edge sequence control - change-over in the gap Machine dimensions 1085 x 180 x 235 cm (with opened doors)

Condition: used, Year of construction: 2000, machine/vehicle number: 0-201-21-369, functionality: fully functional, operating hours: 999,999 h, power: 25 kW (33.99 HP), input voltage: 400 V, input current: 45 A, input frequency: 50 Hz, type of input current: three-phase, travel distance X-axis: 4,700 mm, travel distance Y-axis: 1,350 mm, travel distance Z-axis: 400 mm, workpiece length (max.): 4,500 mm, workpiece width (max.): 1,150 mm, workpiece height (max.): 200 mm, number of axes: 4, number of slots in tool magazine: 12, controller manufacturer: Homag, actuation type: electric, total height: 2,400 mm, total length: 7,250 mm, total width: 4,000 mm, overall weight: 7,500 kg, table length: 4,500 mm, table width: 1,150 mm, Equipment: CE marking, documentation/manual, We are offering this used HOMAG BOF 41/45/R machining center, manufactured in 2000. Manufacturer: HOMAG Model: BOF 41/45/R Year of manufacture: 2000 Condition: used Category ID: 2076 Type ID: 970 Machine type: Machining center Includes 3 vacuum pumps: 2 Siemens Elmo (Elmo Rietschle) vacuum pumps, type: 2BL2141-2AH50-4A-ZN01 Nsdjzwm Rbspfx Ahfslf + 1 Rietschle VTA140 vacuum pump The machine is connected and still in use. Inspections are welcome! Available from mid-December! If you have any questions or require further information, please do not hesitate to send us a message or call us.

Condition: good (used), Year of construction: 2015, machine/vehicle number: 0-200-24-0779, functionality: fully functional, input voltage: 400 V, input current: 55 A, input frequency: 50 Hz, type of input current: three-phase, workpiece height (max.): 60 mm, edge thickness (max.): 20 mm, total length: 10,825 mm, Used single-sided HOMAG edge-banding machine for straight edges – KAL 370 For pre-milling (jointing trimming), gluing and post-processing of various kinds of edging materials. Fixed stop on the left side. Year of Manufacture: 2015 EQUIPMENT / SPECIFICATION Nsdpfx Ajztl Scehfolf BASIC MACHINE - with 80 mm wide conveyor chain with rubber-coated chain pads, - workpiece thickness 8 to 60 mm - top pressure with compound V-belt, automatic height adjustment (to workpiece thickness) - panel support with roller guide, extractable approx. 700 mm - glue roller drive in case of feed stop - hand switch /remote control for setup – mode - adjustable infeed fence with NC-axis (CAN-bus) - Jointing trimming 2 motors (clockwise, counterclockwise), 2x4kW, rear motor w. jumping function GLUING SECTION V20, consisting of: - QA60 glue application unit, with PTFE-coating (Teflon), with manual quick-adjustment glue gates - pneumatic clamping of glue application in mount - Pre-melter for EVA glue - Edge magazine, edge thickness min. 0,4 mm to max. 20 mm Edge width (height) max 65 mm - modes: edge rolls, (veneer) strips, solid wood edging - Pressure zone with automatic horizontal adjustment (NC CAN-axis) to edge thickness, 1 driven & 4 non-driven pressure rollers. POST-PROCESSING SECTION: - Snipping (end-trimming) unit PK85 horizontal, 2 motors, with straight/chamfer cutting function - Rough trimming 2x1.15 kW, top/bottom - Corner rounding FK11, 2 motors (top/bottom) with various trimming heads, motorised adjustment - Universal trimming unit, (e.g. grooving), 3.5 kW, tiltable, w. electro-pneumatic jumping control - Multi-Profile (radius-) scraping MN11 with automatic positioning by NC-axis (CAN) - Flat scraping (glue joint) FA20, top/bottom, (version with 3 tracer rollers) - Buffing unit FP10, top/bottom Control / software: - powerControl PC 23 PowerTouch - woodCommander 5 Machine dimensions 1085 x 180 x 235 cm (with opened doors)

Condition: ready for operation (used), Year of construction: 1997, Max. workpiece length: 3600mm, max. workpiece width: 1400mm, length: 8750mm, width: 5250mm. Nljdpfx Aheqvnl Tofef

Condition: excellent (used), Year of construction: 2010, functionality: fully functional, Used 4-axis CNC machining center Manufacturer: Homag Type: BAZ 211 Venture 21L Year of manufacture: 2010 Highlights! - Flex 5+ unit - PowerEdge gluing unit Nlsdpfxozp Edqo Ahfof - MPU drilling head - and more Console table with 8 manually adjustable consoles, 2 vacuum cups each, side and end stops, LED position indicator for vacuum cups 6 sets of extraction rails, vacuum connection for templates WORKPIECE PARAMETERS: – Workpiece dimensions / work table: 4175*1550 mm – Workpiece thickness: – Max. 300 mm including clamping devices for milling; with standard clamp max. 60 mm; gluing: max. 40 mm – Up to max. 60 mm with standard clamp SAFETY AND PROTECTION DEVICES: CE compliant; SAFETY GUARD ON THE RIGHT WITH DOOR left and rear: wall mounting! Tooling: 18 kW spindle and 18-position tool changer (turret) + 10-position turret changer, C-axis and interface for Flex5+ unit MPU drilling head with 30 spindles (V20/H10/S360°) (integrated swivel axis 0-185°) Flex5+ sawing/drilling/milling unit Power Edge 360° gluing package with pre-trimming station and 1-roll Blowing nozzle for workpiece edge 2* combined edge/radius milling and pull blade unit Tool change station on the right VACUUM PUMP 100/140 m3/h Control: POWERCONTROL PC85 CONTROL PANEL FOR PROGRAM START; WOODWOP Version 6.0 DOCUMENTATION AND CONTROL TEXTS: GERMAN Delivery includes only the tools and HSK chucks shown in the pictures!

Condition: as good as new (ex-display), Year of construction: 2024, operating hours: 10 h, functionality: fully functional, machine/vehicle number: 0-253-73-2182, total width: 1,503 mm, total length: 3,204 mm, total height: 1,900 mm, type of input current: three-phase, overall weight: 1,750 kg, rotational speed (max.): 24,000 rpm, spindle speed (max.): 7,500 rpm, input voltage: 400 V, workpiece height (max.): 80 mm, working width: 1,250 mm, number of spindles: 10, input frequency: 50 Hz, input current: 20 A, workpiece length (max.): 1,250 mm, workpiece width (max.): 800 mm, Equipment: rotational speed infinitely variable, We are offering this ex-demonstration machine, a HOMAG DRILLTEQ D-510 dowel drilling machine, manufactured in 2024. It is currently located in our showroom in AT-4894 Oberhofen am Irrsee. Nedpfx Ahszvnk Tefslf Machine type: DRILLTEQ D-510 OPTIMAT ABD210/12/B/D/F Machine number: 0-253-73-2182 Year of manufacture: 2024 Dowel drilling and milling machine with 5 horizontal and 5 vertical drilling spindles, dowel insertion unit 8mm, as well as a horizontal and a vertical milling spindle (24000 revolutions, 4kW). Processing length 1250mm, with the possibility of overhang if required. Maximum workpiece thickness 80mm, minimum thickness 10mm. Automatic adjustment of the clamping beam height. Hands-free barcode scanner. IntelliGuide operator guidance system. If you have any questions or require further information, please feel free to send us a message or call us.

Condition: used, machine/vehicle number: 008519, Type of edging: Thin edge, Thick edge Gluing System: PUR, Laser Premilling Unit: yes Corner Rounding Unit: yes Grooving Unit: yes Max feed speed: 40 m/min Maximum panel thickness: 60 mm Operating Units: 12 nr Njdpfx Aezruytjhfslf

Condition: good (used), Aggregate kit, format processing unit, chipping unit, milling unit, form milling unit, jointing milling unit, trimming unit, double-end tenoner, edge processing machine, scoring motor, chipping motor, milling motor for edge processing machine -Manufacturer: Homag, milling unit for edge processing machines with Perske motors -Milling units: pivoting Nedpfjvy Tdwsx Ahfjlf -Motors: 2 x Perske DKNS 502/2 -Power: 0.15 kW -Frequency: 200 Hz -Speed: 10400 rpm -Number: 1x milling unit available -Dimensions: 470/410/H600 mm -Weight: 60 kg

Condition: good (used), Profile scraper unit, profile scraper, flat scraper unit, finishing unit, modular unit, format processing unit, double-end tenoner, edge processing machine, scraper for edge processing machine -HOMAG finishing unit allows you to smooth the milled edges for optimal appearance of the edge overhang -with scanning of 2 sides each -scraping blade from above and below -Quantity: 1 piece available -Dimensions: 500/450/H650 mm -Weight: 60 kg Nledpfxeb Sc Stj Ahfef

Condition: good (used), Modular aggregate unit, format processing unit, machining unit, milling unit, form milling unit, jointing milling unit, end-cutting unit, double-end tenoner, edge processing machine, scoring motor, chipper motor, milling motor for edge processing machine -HOMAG cutting unit for cutting off edge protrusions on the front and rear edges -with heavy leadership -Milling unit: swiveling -1x Perske motors -Engine Type: -Power: 0.75 kW -Voltage: Volts -Frequency: 300 Hz -Speed: 8,600 rpm -Other engines with different performance levels are available from us for an additional charge. -Dimensions: 990/620/H340 mm -Weight: 52 kg Nljdob Sc Svepfx Ahfef

Condition: good (used), Finishing unit, buffing unit, modular unit, format processing unit, double-end tenoner, edge processing machine, after the scraper for edge processing machine -HOMAG finishing unit for cleaning agent application with buffing wheel for removing glue residue from PVC edges -with 2 motors for cleaning from above and below Nljdpfxsb Sgzds Ahfjf -with oscillation -Swivelable - laterally adjustable -Height: adjustable -Number: 1x aggregate available -Dimensions: 400/370/H470 mm -Weight: 35 kg

Condition: used, Unit carrier, clamping plate traversing table, for unit construction kit, format processing unit, cutting unit, milling unit, profile milling unit, jointing milling unit, trimming unit, double-end profiler, edge processing machine, scoring motor, chipper motor, milling motor for edge processing machine -HOMAG unit carrier for milling units Nsdsb Uhpbopfx Ahfslf -with heavy leadership -laterally movable -with counter -Table height: 280 mm -Table surface: 3240 x 295 mm -Table thickness: 20 mm -Price: per piece -Number: 2x available -Dimensions: 3240/295/H280 mm -Weight: 330 kg

Condition: good (used), Unit carrier, clamping plate, travel table, for modular units, format processing unit, chipping unit, milling unit, profile milling unit, jointing milling unit, cross-cutting unit, double-end tenoner, edge processing machine, scoring motor, chipping motor, milling motor for edge processing machine -HOMAG unit carrier for milling units -with heavy guidance -laterally movable -with counter -Table height: 275 mm -Table surface: 3575 x 295 mm -Table thickness: 20 mm -Price: per piece -Quantity: 1x available Njdpeb Uhpcjfx Ahfolf -Dimensions: 3575/295/H275 mm -Weight: 356 kg

Condition: used, Unit construction kit, format processing unit, cutting unit, milling unit, profile milling unit, jointing milling unit, trimming unit, double-end profiler, edge processing machine, scoring motor, chipper motor, milling motor for edge processing machine -HOMAG milling unit: for format processing -with heavy dovetail guide -1x engines Perske -Motor type: KNS 70.12/2.DF1 KNS 51.15.20 -Power: 3/4.4 kW -Voltage: 220/380/380 volts -Frequency: 50/100 Hz -Speed: 2880/5880 rpm -2x engines Perske -Motor type: KNS 51.15/2D -Power: 1.1/2.2 kW -Voltage: 220/380/380 volts Nlsdpsb Uhvqjfx Ahfsf -Frequency: 50/100 Hz -Speed: 2640/5600 rpm -Other engines with other services in stock for an additional charge -Dimensions: 1150/1100/H1200 mm -Weight: 625 kg

Condition: good (used), Interface, control card, output card, control unit, edgebander, edgebander -Manufacturer: HOMAG HOMATIC -Type: 2Type: 2083016303 Njdpfx Ascczkzshfslf -Number: 2 control cards available -Price: per piece -Dimensions: 20/195/H265 mm -Weight: 0.27 kg