Used Hebrock for sale (48)

Condition: ready for operation (used), Year of construction: 2024, workpiece height (max.): 60 mm, feed rate X-axis: 10 m/min, spindle speed (max.): 16,000 rpm, control type: PLC-controlled, The machine has already been disassembled and stored by a specialist. TECHNICAL DETAILS Rotational speed of the miter saw station: approx. 16,000 rpm Rotational speed of the milling station: approx. 16,000 rpm Maximum milling depth: 3 mm Design for edge thickness: 1 mm Hot melt adhesive specification for edge material max.: 3 mm Feed rate: approx. 10 m/min Maximum workpiece thickness: 60 mm EQUIPMENT Maintenance-free, coated glue basin with provision for interchangeable basins Glue dispensing device Pneumatic milling adjustment Combination design with interchangeable plate cutter Corner rounding milling cutter Radius drawing blade Surface drawing blade with pneumatic extraction device Cleaning station Robust chain drive Ball-bearing mounted double roller pressure pad Aggregate viewing window from the machine's rear and operator side Signal lamp for workpiece sequence Extendable workpiece support ACCESSORIES Hebrock 8 mm version Hebrock quick-change system for corner milling cutter Gkjdezb Idfepfx Acmsd Hebrock jointing up to 60 mm workpiece thickness Hebrock protective spray for edges Hebrock nesting (milling cutter + radius drawing blade) Hebrock Airtronic Note: Accessories are provided without guarantee. The principle applies: "Item purchased as seen." The prospective buyer must verify the completeness of the item on-site.

Condition: used, Year of construction: 1990, Storage location: Nattheim Gksdpez H Tw Dofx Acmjd

Condition: good (used), Year of construction: 2003, I sell the radius milling machine HEBROCK HFF08, Year 2003. Suitable for curved shaped edges Gedpfxewun H Uo Acmskd Good condition, possible to test ! Possible to buy also the Radius edge banding machine AKV88D.

Condition: new, Year of construction: 2026, Pre-milling unit End Trim saw Top and Bottom Trimming unit Corner Rounding Unit Surface Scraper Touch Screen Controller Max. edge thickness: 3mm Min./max. workpiece thickness: 8–50mm Min. workpiece length: approx. 160mm Feed speed: 10 m/min. Ready to operate: approx. 3.5min. Power consumption: ∅ approx. 7.4kW Gjdpeglfwtofx Acmekd Electrical connection: 400V/3Ph/50Hz Table height: approx. 900mm Machine dimensions: approx. 4,050x1,300x1,400mm (LxWxH) Weight: approx. 820kg Exhaust connection: ∅ 1x140mm Edge Banding Machine with PLC Premilling (DIA-tools incl.) up to max. 2 mm milling depth Corner rounding unit Radiusmilling R=2 mm Radius edge milling R=2 mm radius profile scraper protection spraying edge

Condition: new, Year of construction: 2026, The machine is on stock!!! Max. edge thickness 3 mm Min./Max. workpiece thickness 8 – 50 mm Min. workpiece length approx. 160 mm Feed speed 10 m/min Gluepot heating time approx. 3.5 minutes Power consumption Ø approx. 7.4 kW Electrical connection 400 V/3 phase/50 Hz (Transformed to your voltage) Gksdpshymgdofx Acmed Table height approx. 900 mm Machine dimensions (LxWxH) 4300x1300x1400mm Weight approx. 900 kg Exhaust connection Ø 1 x 140 mm protection spraying edge Pneumatic 3-point-adjustment (radius-, champfer-, flatmilling)

Condition: new, 3 mm Total length 4122 mm Feed speed 10 m/min. Gkedpfxjvwd Uus Acmsd with PLC control (incl. touchscreen) and hot-melt adhesive application to the workpiece foredgebanding material up to 3 mmjointing cutter (incl. DIA tool) up to 2 mm cutter depth1),maintenance-free glue tray with change tray pre-equipment incl. adhesive discharge device,HF cross-cut saw station (approx. 12,000 rpm),HF trimming station (approx. 12,000 rpm) with separate pneumatic trimming adjustment andchange plate trimmer (combined version),corner rounding cutter,surface scraper (incl. pneumatic discharge device) with separate pneumatic trimming adjustment andchange plate trimmer (combined version),corner rounding cutter) with separate pneumatic routing adjustment andinterchangeable plate router (combi version),corner rounding router,surface scraper (incl. pneumatic lift-out),free space (for cleaning station or radius scraper),robust chain drive,ball bearing mounted double roller top pressure,viewing window from rear of machine,pull-out workpiece support,feed rate approx. 10 m/. No. F4/00/11- Joining head WhispercutF4/500/10- Combination milling headF4/500/20- Radius milling cutter R=2mmF4/500/2- Radius corner milling cutter R=2mmF4/08/2- Quick-change equipment for corner milling cutterF4/08/4- Radius scraper (incl. F4/09- Radius radius scraper R=2mmF4/09/2- ChassisF4/10- Pneumatic 3-point adjustment(radius, chamfer, flush milling)F4/30

Condition: good (used), Year of construction: 2002, I sell the edge banding machine HEBROCK AKV088D, Year 2002. Suitable for curved shaped edges Gjdpfx Acovx D Auemekd Good condition, possible to test ! Possible to buy also the Radius milling machine HFF08.

Condition: new, Year of construction: 2026, Space-saving with excellent specifications. Your entry point into edgebanding could not be better, as the 3.3m long F2 is both cost-effective and space-saving. And it also has the specifications you require to process perfect edges right from the word go – diamond-tipped cutters guarantee superbly prepared workpieces for edging. The specifications include pre-milling aggregate (up to 3 mm), the top-side fast-heating glue pot, trim saw and combicutter. The F2 can also be optionally fitted with a surface scraper. Get started into perfect edgebanding! Max. edge thickness: 3mm Min./max. workpiece thickness: 8–50mm Min. workpiece length: approx. 160mm Feed speed: 10 m/min. Ready to operate: approx. 3.5 min. Gsdpfx Ajglfw Nscmekd Power consumption: ∅ approx. 5.9 kW Electrical connection: 400 V/3Ph/50Hz Table height: approx. 900 mm Machine dimensions: approx. 3,350 x 1,300 x 1,400 mm (LxWxH) Weight: approx. 620 kg Exhaust connection: ∅ 1x140 mm Surface scraper (incl. pneumatic disengagement)

Condition: new, Year of construction: 2025, The Hebrock F 2 The 3.3 m long F 2 is not only attractively priced and space-saving. It also features the equipment you need to process edges perfectly from the start: diamond-tipped joining cutters guarantee excellently prepared workpieces for edge banding. The equipment includes a joining unit (up to 2 mm cutting depth), the top-mounted quick-heating glue tank, a mitre saw, and a combination milling machine. Optionally, the F 2 can also be equipped with a surface scraper blade. Maximum edge thickness: 3 mm Maximum workpiece thickness: 50 mm Ready for operation in 3.5 minutes Equipment: F2 - 10 m/min Edge banding machine F2 next Gksdpfx Acslht Hzsmjd With PLC control (including touchscreen) and hot melt glue application to the workpiece for edge material up to 3 mm; joining cutter (including diamond tool) up to 2 mm cutting depth, maintenance-free glue tank with interchangeable tank provision including glue outlet device, HF mitre saw station (approx. 12,000 rpm), HF milling station (approx. 12,000 rpm) with separate pneumatic milling adjustment and interchangeable plate milling cutter (combination version), robust chain drive, ball-bearing double roller pressure, viewing window from the back of the machine, pull-out workpiece support, feed rate approx. 10 m/min. F2/10 carriage F2/30 pneumatic 3-point adjustment (radius, bevel, flush milling)

Condition: new, Year of construction: 2026, Max. edge thickness 3 mm (optionally up to 8 mm) Min/Max. work piece thickness 8–60 mm* Min. workpiece length approx. 200 mm* Min. workpiece width approx. 80 mm* Feed speed approx. 10 m/min. Ready to operate approx. 6 min. Power consumption max. approx. 14 kW Electrical connection 400 V – 3 Ph – 50 Hz Machine dimensions 5,250 x 1,230 x 1,430 mm (LxWxH) Weight approx. 1,700 kg Gedpfsg Tu Rkex Acmekd pre-milling head Whispercut radius for corner rounder R = 2mm heatable infeed fence quick change device f.motor corner rounder change motor for corner rounding unit including HM profile cutter radius for change motor R = 1mm Radius Multi-Radiusscraper R2/R1 wheels release agent spraying unit cleaning agent spraying unit protection spraying edge nesting pneumatic 3-point adjustment

Condition: used, Year of construction: 1994, for pre-coated edges including a lot of edge material with outriggers on both sides end cap station 3-roller feed used, good condition Make Hebrock Type AKV-83 Year of construction 1994 Gsdjvwfzvepfx Acmskd Edge band thickness 1.0 mm Workpiece height max. 50 mm Workpiece width min. 50 mm Workpiece length min. 170 mm Space requirement approx. 1700 mm x 690 mm x 500 mm Storage location 97447 Gerolzhofen, freely loaded, unpacked Handover in the current condition as seen, without guarantee and guarantee

Condition: new, Year of construction: 2026, Hebrock F 4 For the complete processing of your panels For those who don’t want to compromise. With the F 4, we offer you a model that allows you to produce completely finished edges on a machine length of only 4 meters. The F 4 is not only space-saving but also extremely attractive in terms of price-performance ratio. Max. edge thickness: 3 mm Min/Max. workpiece thickness: 8 – 50 mm Min. workpiece length: approx. 160 mm Feed speed: approx. 7 m/min Ready for operation: approx. 3.5 min Max. power consumption: approx. 7.4 kW Electrical connection: 400 V – 3 phases – 50 Hz Work table height: approx. 900 mm Machine dimensions: approx. 4050 x 1300 x 1400 mm (L x W x H) Weight: approx. 820 kg Extraction nozzle: Ø 1 x 140 mm PLC control with 10″ touchscreen Top-mounted rapid heating glue tank (maintenance-free) Support plate for edge material Automatic central lubrication (miter saw, corner router) Optical display for workpiece sequence Outrigger (extendable to the front) Quick-change unit preparation, including glue change device for PUR processing Surface scraping blade with dual contact Pneumatic roller capping (scissors-type design, Hebrock system) Double roller pressure (ball-bearing mounted) Transport chain with permanently screwed-on special chain plates Edge router Routing unit Miter saw Corner router Accessories: Gsdpfx Aehqadcocmjkd F4/09 Radius scraping blade (incl. pneumatic lift) F4/09/4 Multi radius scraping blade (R1/R2) F4/30 Pneumatic 3-point adjustment Location: In stock, 54634 Bitburg - available on short notice -

Condition: new, Year of construction: 2026, The Hebrock K 36 Top model with motorized adjustment – a new machine. This Hebrock bestseller offers unprecedented possibilities. Developed for the highest standards, the K 36 stands for absolute reliability and productivity in daily use. By enabling the machine to be equipped with a stepped cutter and a multi-radius trimming cutter, Hebrock sets new standards in the field of perfect edge finishing for various edge thicknesses. Max. edge thickness: 3 mm Max. workpiece thickness: 60 mm Ready for operation in 6 min. Max. edge thickness: 3 mm Min/Max. workpiece thickness: 8 – 60 mm Min. workpiece length: approx. 140 mm Feed speed: approx. 15 m/min Ready for operation: approx. 6 min Gedpfx Acoi Am Ukemokd Max. power consumption: approx. 7.4 kW Electrical connection: 400 V – 3 phases – 50 Hz Work table height: approx. 900 mm Machine dimensions: approx. 5250 x 1230 x 1430 mm (L x W x H) Weight: 1750 kg Equipment: Hebrock K 36. - 15 m/min Edge banding machine K36 With PLC control (incl. 15'' touchscreen), hot melt adhesive application to the workpiece for edge material up to 3 mm; trimming cutter (incl. diamond tool) up to 3 mm cutting depth, maintenance-free, coated glue tank with interchangeable tank preparation including glue discharge device, high-frequency double-motor trim saw station (approx. 12000 rpm), high-frequency milling station (approx. 12000 rpm) with pneumatic milling adjustment and interchangeable cutter (combination design), corner rounding cutter, radius trimming cutter, flush trimming cutter (incl. pneumatic retraction device), cleaning station, robust chain drive, ball-bearing double roller pressure, unit sight window from the machine rear and operator side, signal lamp for workpiece sequence, pull-out workpiece support, feed speed approx. 15 m/min, edge banding up to 60 mm workpiece thickness 36/08/1 Quick-change preparation for corner cutter 36/08/2/1 additional interchangeable motor for corner cutter R=1 36/09/1 Multi-radius trimming cutter 36/24/1 Release agent spray device 36/24/2 Cleaning agent spray device 36/25 Edge protection spray 36/27 Nesting (1x milling station + 1 x radius trimming cutter) 36/30 Pneumatic 3-point adjustment 36/30/1 Multi-tool for high-frequency milling station (R2/R1/chamfer) 36/45 Axis package Motorized adjustment for panel, edge thickness, and trimming cutter depth adjustment Location: in stock, 54634 Bitburg Available upon agreement.

Condition: new, Year of construction: 2025, The Hebrock F 2 The 3.3 m long F 2 is not only affordable and space-saving, but it also boasts the features you need to process edges perfectly from the start: diamond-tipped joiner cutters guarantee excellently prepared workpieces for edgebanding. The equipment includes a joiner unit (up to 2 mm cutting depth), the top-mounted quick-heating glue container, a miter saw, and a combination router. Optionally, the F 2 can also be equipped with a surface scraping blade. Gkjdpfxji Am U Ds Acmjd Maximum edge thickness: 3 mm Maximum workpiece thickness: 50 mm Ready for operation in 3.5 minutes Equipment: F2 - 10 m/min Edgebanding machine F2 next With PLC control (including touchscreen) and hot-melt glue application to the workpiece for edge material up to 3 mm; joiner cutter (including diamond tool) up to 2 mm cutting depth, maintenance-free glue tank with replaceable tank preparation including glue dispensing device, high-frequency miter saw station (approx. 12,000 rpm), high-frequency router station (approx. 12,000 rpm) with separate pneumatic router adjustment and interchangeable blade router (combination design), robust chain drive, ball-bearing double roller pressure, viewing window from the back of the machine, pull-out workpiece support, feed rate approx. 10 m/min. F2/10 chassis F2/30 pneumatic 3-point adjustment (radius, chamfer, flush trimming)

Condition: ready for operation (used), Year of construction: 2004, Brand: Hebrock Model: AKV 83 F Year of manufacture: 2004 Machine no: 10759 Technical data: Workpiece thickness: from 10 - 50 mm Godpfeu Racxsx Acmokd Feed speed: 3 - 4 m/min Electrical connection: 220/380 Volt, 50 Hz. Power: 3 KW Dimensions: 1750 x 800 x 1250 mm (complete) Weight: approx. 95 kg. Heating: 3 KW, with stepless electronic temperature control, 0 - 650 degrees C Motor: 3.5 kW Stock no: 2002311BXA

Condition: new, Year of construction: 2026, The Hebrock F 5 If you want maximum performance, the Hebrock F 5 is the solution for edgebanding in demanding workshops. The F 5 guarantees edge processing in all steps, as it is equipped with all the components you need for your requirements: jointing cutter, miter saw, milling unit, radius pull blade, corner cutter, surface pull blade, and finishing station. For even more flexibility on the way to the perfect finish, the F 5 can optionally be equipped with a practical multi-radius pull blade. Maximum edge thickness: 3 mm Maximum workpiece thickness: 50 mm Ready for operation in 3.5 minutes Equipment: Hebrock F5 Next - 10 m/min Edgebanding machine F5 Next With PLC control (including touchscreen) and with hot melt adhesive application to the workpiece for edge material up to 3 mm; jointing cutter (including diamond tool) up to 2 mm cutting depth, maintenance-free glue tank with interchangeable tank preparation including glue dispensing device, HF miter saw station (approx. 12,000 rpm), HF milling station (approx. 12,000 rpm) with separate pneumatic milling adjustment and interchangeable plate cutter (combination design), corner rounding cutter, radius pull blade, surface pull blade (including pneumatic feed), finishing station, robust chain drive, ball-bearing double roller pressure, viewing window from the back of the machine, pull-out workpiece support, feed rate approx. 10 m/min. Gksdpelht Hwefx Acmod Hebrock F5 F5/08/4 Quick-change preparation for corner cutter F5/08/5 additional interchangeable motor for corner cutter with tool set F5/09/4 Multi-radius pull blade (R1/R2) F5/10 Chassis F5/14 additional interchangeable tank F5/24/1 Spray device for release agent F5/24/2 Spray device for cleaning agent F5/25 Spray device for edge F5/27 Nesting for cutter and radius pull blade F6/28 Spray texture finish F5/30 Pneumatic 3-point adjustment (radius, bevel, flush milling) F5/31 Jointing up to 50 mm F5/32 LED lighting Location: In stock, 54634 Bitburg - available immediately -

Condition: new, Year of construction: 2025, Edge banding machine F5 with PLC control (including 15" touchscreen), Gkodjh Hl Ayspfx Acmjd hot melt adhesive application to the workpiece for edge banding material up to 3 mm: Joint milling cutter (including DIA tool) up to 2 mm cutting depth, maintenance-free glue pot with interchangeable pot preparation, including adhesive dispensing device, HF milling station with pneumatic milling adjustment, including corner rounding milling cutter, radius trimming knife, edge trimming knife (including pneumatic extraction device), finishing station Joint head Whispercut Combination milling head Radius milling cutter R=2mm Radius corner milling cutter R=2mm Quick-change preparation for corner milling cutter Radius change motor R=1mm Multi-radius trimming knife R1/R2 Chassis Spray device for release agent (PUR) Spray device for cleaning agent (PUR) pneumatic 3-point adjustment LED lighting INCLUDING 2nd interchangeable glue pot max. edge thickness 3mm Workpiece thickness 8-50mm min. workpiece length approx. 160mm Feed speed 10m/min Ready for operation in approx. 3.5 min Dimensions approx. 4300x1300x1400mm LxWxH Weight approx. 900kg Extraction port 1 x 140mm

Condition: new, Year of construction: 2026, The Hebrock F 5 If you want maximum performance, the Hebrock F 5 is the solution for edge banding in demanding craft businesses. The F 5 guarantees edge processing in all steps, as it is equipped with all the components you need for your requirements: grooving cutter, miter saw, milling unit, radius pull blade, corner cutter, surface pull blade, and finishing station. For even more flexibility on the way to the perfect finish, the F 5 can optionally be equipped with a practical multi-radius pull blade. Max. edge thickness: 3 mm Max. workpiece thickness: 50 mm Ready for operation in 3.5 minutes Equipment: Hebrock F5 Next - 10 m/min Edge banding machine F5 Next With PLC control (incl. touchscreen) and hot melt adhesive application to the workpiece for edge material up to 3 mm; grooving cutter (incl. diamond tool) up to 2 mm cutting depth, maintenance-free glue tank with interchangeable tank preparation incl. glue dispensing device, high-frequency miter saw station (approx. 12,000 rpm), high-frequency milling station (approx. 12,000 rpm) with separate pneumatic milling adjustment and interchangeable plate milling cutter (combination design), corner rounding cutter, radius pull blade, surface pull blade (incl. pneumatic lifting mechanism), finishing station, robust chain drive, ball-bearing double roller pressure pad, viewing window from the rear of the machine, extendable workpiece support, feed rate approx. 10 m/min. Hebrock F5 F5/08/4 Quick-change preparation for corner cutter F5/08/5 additional interchangeable motor for corner cutter with tool set F5/09/4 Multi-radius pull blade (R1/R2) F5/10 Undercarriage F5/14 additional interchangeable tank F5/24/1 Spray device for release agent F5/24/2 Spray device for cleaning agent F5/25 Spray device for edge F5/27 Nesting for milling cutter and radius pull blade F6/28 Spray for texture finish F5/30 Pneumatic 3-point adjustment (radius, bevel, flush milling) F5/31 Jointing up to 50 mm F5/32 LED lighting Location: In stock at warehouse 54634 Bitburg Immediately available - in stock. Gsdpei Anadofx Acmskd

Condition: good (used), Year of construction: 2005, Brand: Hebrock Model: HFF 08 Machine no: 08/379 Year model: 2005 Edge cutter for simultaneous upper and lower radius/clean milling of excess edging material on workpieces with straight edges and on rounded workpieces with internal and outside radii. Tech data: Max edging thickness: approx. 3mm Max workpiece height: 50mm Inner radius min: 40mm Gsdpsq H Spvefx Acmskd Milling motor: 12000 Rpm Work table height: 865mm Max 6 bar Chipboard: 120mm Milling motor: 0.37Kw Motor: 1.5Kw, 50Hz, 400V 3-phase Stock no: 2001922

Condition: new, ALTENDORF Model F 2 Offer type: New machine, SALE ONLY IN AUSTRIA! Immediately available new machine at a special price with full manufacturer's warranty. Gksdpfsl D Rp Esx Acmed The 3.3 m long F 2 is not only cost-effective and space-saving. It is also equipped with everything you need to process perfect edges from the start: diamond-tipped jointing cutters ensure workpieces are excellently prepared for edge banding. The equipment includes a jointing unit (up to 2 mm cutting depth), top-mounted quick-heating glue pot, cross-cut saw, and combination milling cutter. Optionally, the F 2 can also be fitted with a surface scraper. Max. edge thickness: 3 mm Max. workpiece thickness: 50 mm Ready for operation in 3.5 min Feed rate approx. 10 m/min Equipment: F2 next edge banding machine With PLC control (incl. touchscreen) Hot-melt adhesive application to the workpiece for edging material up to 3 mm Jointing cutter (incl. diamond tool) up to 2 mm cutting depth Maintenance-free glue pot with quick-change option incl. glue discharge device HF cross-cut saw station (approx. 12,000 rpm) HF milling station (approx. 12,000 rpm) with separate pneumatic milling adjustment and interchangeable cutter head (combination version) Robust chain drive Ball-bearing double pressure roller Viewing window from the rear of the machine Extendable workpiece support Including special equipment: F2/12 surface scraper (incl. pneumatic lift) F2/30 pneumatic 3-point adjustment (for radius, chamfer, or flush trimming) F2/27 nesting for milling stations

Condition: ready for operation (used), Year of construction: 2016, machine/vehicle number: 3214, functionality: fully functional, workpiece height (max.): 40 mm, feed rate X-axis: 10 m/min, total height: 1,600 mm, total length: 3,700 mm, total width: 1,445 mm, overall weight: 1,080 kg, TECHNICAL DETAILS Feed speed: 10 m/min Panel thickness: 8 - 40 mm Max. edge thickness: 3 mm MACHINE DETAILS Operating length: approx. 100,000 m Dimensions & Weight Dimensions (L x W x H): 3,700 x 1,445 x 1,600 mm Weight: 1,080 kg EQUIPMENT/FEATURES PLC control including touchscreen Power stop/trimming knife Godpfey Hih Rsx Acmekd Jointing unit with DIA milling tools Application of hot melt adhesive to workpiece Robust chain drive Upper operator panel, rapid adjustment from operator side Double roller pressure Signal lamp for workpiece feed Quick-heating glue pot, maintenance-free Pneumatic end trimming for edge thicknesses up to 3 mm High-frequency crosscut saw High-frequency milling unit with replaceable cutter heads For radius, straight and chamfer milling Workpiece air blower Integrated collection container for edge material offcuts Extendable support arm on the front side Note: The machine can still be inspected under power until the middle of calendar week 19.

Condition: used, Year of construction: 2020, power: 6 kW (8.16 HP), workpiece height (max.): 50 mm, edge thickness (max.): 3 mm, Equipment: CE marking, No minimum price – guaranteed sale to the highest bidder! The pick-up deadlines specified in the General Terms and Conditions apply. The absolute latest pick-up deadline is August 31, 2026! TECHNICAL DETAILS Plate thickness min.: 8 mm Plate thickness max.: 50 mm Edge thickness min.: 0.3 mm Edge thickness max.: 3 mm Gedpfx Ajzf Ircscmekd Adhesive system: EVA hot melt adhesive The machine consists of 4 processing units as follows: Unit 1 Pre-milling unit Number of pressure rollers: 3 Adhesive pot for EVA hot melt adhesive Unit 2 Edge processing unit: Capping Number of motors: 1 Unit 3 Edge processing unit: Fine milling for flush trimming and rounding Number of motors: 2 Unit 4 Processing unit: Glue application blade MACHINE DETAILS Total installed power: 6 kW The machine is sold and delivered in its actual and legal condition (“as is, where is”) based on photographic documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods before pick-up and assumes responsibility for the installation, securing, and use of the machine at the destination. External reference: 8571

Condition: used, Year of construction: 2014, power: 12 kW (16.32 HP), edge thickness (max.): 8 mm, feed rate X-axis: 10 m/min, plate height: 40 mm, Equipment: CE marking, No minimum price – guaranteed sale to the highest bidder! The pick-up deadlines specified in the general terms and conditions apply. The absolute latest pick-up date is August 31, 2026! TECHNICAL DETAILS Feed rate max.: 10 m/min Workpiece height max.: 40 mm Workpiece length min.: 200 mm Workpiece width min.: 80 mm Edge thickness min.: 0.3 mm Edge thickness max.: 8 mm Number of processing units: 5 Number of panel dividing/milling units: 1 Number of edge processing units: 4 Adhesive system: EVA hot melt adhesive The machine consists of the following processing units: Panel dividing/milling unit Unit: Pre-milling unit Edge processing unit 1 Processing unit: Capping Number of motors: 1 Edge processing unit 2 Processing unit: Fine milling for flush trimming and rounding Number of motors: 2 Edge processing unit 3 Processing unit: Corner rounding Number of motors: 1 Edge processing unit 4 Processing unit: Glue application blade MACHINE DETAILS Total installed power: 12 kW EQUIPMENT Gkedezf Id Sjpfx Acmjd CE marking Overpressure Pressure with idler rollers Panel support guides Edge roller magazine Adhesive pot for EVA hot melt adhesive Infeed roller for pressing the edge 4 pressure rollers Corner rounding unit The machine is sold and delivered in its actual and legal condition (“as is, where is”) based on photo documentation and technical/commercial documents, which are of a descriptive nature. The buyer has the right to inspect the goods before pick-up and assumes responsibility for the installation, securing, and use of the machine at the destination. External reference: 8570