Used Edgebanders for sale (788)

Condition: ready for operation (used), Year of construction: 2009, machine/vehicle number: H/32059, functionality: fully functional, workpiece height (max.): 50 mm, feed rate X-axis: 22 m/min, TECHNICAL DETAILS Ljdpfx Aboydibwsyshn Panel height: 10 mm to 50 mm Solid wood: 12 mm PVC/ABS: 0.4 mm to 3 mm Max. feed speed: 22 m/min Min. panel length: 150 mm Min. panel width: 70 mm MACHINE DETAILS Rectifier group motors: 1.5 kW (2 motors) EQUIPMENT Touchscreen control for adjusting working units Panel support guide Side roller conveyor with idler wheels for panel support Anti-adhesive unit Roll holder plate COMBIMELT glue unit for hotmelt adhesive with automatic VarioMelt dosing and pre-melter Patented edge pressing unit with segmented pads Trimming unit with 2 motors Cleaning unit with 2 motors Rounding unit Edge scraper unit Working height adjustable electronically via C.N. Powered rubberized conveyor with top pressure

Condition: ready for operation (used), machine/vehicle number: 0-200-03-8334, functionality: fully functional, workpiece height (max.): 60 mm, feed rate X-axis: 24 m/min, controller model: Power Control Pc 22, TECHNICAL DETAILS Panel height: 60 mm Solid wood: 20 mm PVC / ABS: 3 mm Feed speed: 24 m/min MACHINE DETAILS Control system: Power Control PC 22 Supply voltage: 480 V Frequency: 60 Hz Lhsdpfx Aboydiymeysn Phases: 3~ + N Operating current: 51 A Fusing: 63 A Phase circuit: 3~ Control voltage: 24 V EQUIPMENT Electronically adjustable working height via CNC Powered, rubberized conveyor belt with increased pressure Panel support guide Lateral roller conveyor with idler rollers for panel support Sanding unit Infrared lamps for panel edge preheating Six-position coil holder magazine with automatic edge change via CNC EVA hot-melt gluing unit with premelter and glue pot Edge pressing unit for straight profiles with electronically adjustable pressure rollers via CNC End trimming unit with two motors and automatic tilt adjustment Overlapping cut-off / milling unit with two motors Glue / milling unit with two tiltable motors, electronically adjustable via CNC Multifunctional 4-motor corner rounding unit (smoothing + rounding) with CNC control, automatic adaptation Provision for integrating an additional working station Edge scraping unit Oscillating brush unit

Condition: used, Year of construction: 2010, Technical details: • Edge material thickness for strip material: 0.4–6 mm • Edge material thickness for coil material (depending on material): 0.4–3 mm • Edge material height: max. 65 mm • Workpiece thickness: 6–60 mm • Minimum workpiece width: 65 mm • Minimum workpiece length: 160 mm • Feed speed: 10 m/min • Integrated control panel on the front side, in the infeed area • Control system: PPC 221 – Power PC • Pull-out workpiece support table, extension: 600 mm • 1801 Pre-milling unit with diamond milling cutter (1 × 0.8 kW, 1 × 1.2 kW, 200 Hz, 12,000 rpm) • 1903 Edge band magazine, pre-cutting up to 3 mm Lsdpfxszxww Uo Abyjhn • 1906 MG combined glue application unit (cartridge and granulate) • Pressure regulator for cartridge glue application with pneumatic control • 1912-3 Pressure roller unit • 1918 Pneumatic end-trimming unit • 1827 Multifunctional milling unit (pneumatic control) • 1832 Corner rounding/milling unit • 1929 Scraper unit, R = 2 mm • 1964 Flat scraper Specifications are provided for information only. This machine is offered for sale on behalf of a customer. Viewing is available by prior arrangement. Please contact us through the platform's messaging system for further information and the relevant technical contact details.

Condition: used, Year of construction: 1993, Used machine Year of manufacture: 1993 Equipment and technical data: Lhedpfxszyy Avs Abysn

Condition: excellent (used), Year of construction: 2021, functionality: fully functional, power: 9 kW (12.24 HP), input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, workpiece height (max.): 60 mm, edge thickness (max.): 3 mm, feed rate X-axis: 23 m/min, total height: 1,500 mm, total length: 3,200 mm, total width: 1,200 mm, overall weight: 1,200 kg, We offer this edge banding machine for shaped components, VITAP ECLIPSE 2.0, in very good condition, manufactured in 2021. Rated voltage: 400 V Frequency: 50 Hz Rated power: 9 kW Air pressure: 6 bar Weight: 1200 kg Dimensions (L × W × H): 3200 × 1200 × 1500 mm Thickness of workpieces: 8–60 mm Feed rate: 9–23 m/min Glue tank capacity: 9 kg Edge banding machine VITAP ECLIPSE 2.0 Device type: FD 21 pro Device number: 120019 P Year of manufacture: 2021 Ljdpezuwdgofx Abyjhn Used device, in very good technical condition, used for one project, used sporadically for over a year, hence the decision to sell. We are interested in selling or exchanging it for a panel saw with a cutting width of 4300 mm (with a price adjustment, of course). Due to the project closure, we are offering for sale: Multi-spindle drilling machine FELDER FD 21 Panel saw HOLZMA OPTIMAT HPP 350 Edge banding machine VITAP ECLIPSE 2.0 The device is connected, fully functional, and can be viewed/tested on-site – Kraków, Rybitwy. The device is designed for edge banding narrow side surfaces of furniture components made of particleboard, plywood, and lumber. The VITAP edge banding machine is ideally suited for edge banding from 1-3 mm. Type: Edge banding - Single-sided edge banding machine Component thickness: 3 mm Edge thickness: 60 mm If you have any questions or need additional information, please send a message or contact us by phone.

Condition: used, Year of construction: 2010, - Equipped with ISAS 28-position edge magazine - PU gluing unit - With Boomerang return system Single-sided edge banding machine Manufacturer: Homag Type: KAL 310/7/A3 Year of manufacture: 2010 Technical data - Equipped with ISAS 28-position edge magazine - PU gluing unit - With Boomerang return system Edge trimming unit with 2 motors, each 3KW, 150 Hz, 9,000 RPM. Pneumatically controlled for pre-trimming PU gluing unit 34 with PU hot melt unit - capacity max. 6 kg/h Container size 2 kg. QA glue application unit Selectable edges from the ISAS 28-position edge magazine 4 pressure rollers Release agent spray unit, top and bottom Trimming unit WK 13, bevel / straight With 2 motors, each 0.4 KW, 200 Hz, 12,000 RPM. Electropneumatic adjustment of the trimming motors to 2 positions (flush trimming and with overhang) Pre-trimming unit with 2 motors, each 0.55 KW, 200 Hz, 12,000 RPM. With double-roller scanning. With electropneumatic adjustment Shaping trimming unit FK 11 - manual For processing the edge overhangs on the top and bottom edges of the workpiece, as well as for milling the front and rear edges With 2 motors, each 0.4 KW, 200 Hz, 12,000 RPM. Universal trimming unit UF 11 Lhodpozuyhhofx Abysn With motor 4 KW, 150 Hz, 9,000 RPM. Swiveling 90°, electropneumatically controlled With HSK 63 F collet for unlocking by push-button Profile scraping unit PN 10 Pneumatic adjustment for moving sideways out of the working area Finishing unit FA11 top/bottom Consisting of: Glue joint scraping blade Cleaning agent application Buffing unit with 2 motors, height adjustment with the upper pressure Machine control via 19-inch touchscreen Return system BOOMERANG ZHR05 With air cushion table, angled, length 2,000 mm, width 1,000 mm Conveyor belt width 1,100 mm Workpiece parameters: Length 300 - 2,500 mm / Width: 60 - 1,100 mm or Length 300 - 800 mm / Width: 1,100 - 2,000 mm Thickness 8 - 60 mm For 4-sided processing: Min. part size: 300 x 300 mm / max. part size 2,000 x 800 mm With roller strip for supporting wider parts.

Condition: used, Year of construction: 2005, Single-sided edge banding machine Manufacturer: IMA Type: Novimat Systems/I/R75/1000 Year of manufacture: 2005 Technical data PC control - ICOS OPEN control system Feed rate 5-25 m/min, frequency-controlled Fence with electronic positioning control Adhesive application above and below Trimming unit with 2 motors, each 4.5 kW, 9,000 rpm, controllable. - Horizontally adjustable via axis Heating element approx. 300 mm long, 2x 1.5 kW Gluing unit - Adhesive application with pneumatic quick-lock system. - Automatic PU melting system Quickmelt for 2 kg cartridges - 32-position edge magazine (8 slots up to 3 mm / 24 slots up to 1.3 mm) Vertical roller holder for 32 rollers, max. diameter 850 mm Cutting unit on the upper pressure roller with 2 motors, each 200 W, 400 V, 12000 rpm. - Horizontal pneumatic swiveling 0-25 - With controllable side contact, for 3 edge thicknesses Trimming unit with 2 motors, each 1000 W, 400 V, 200 Hz, 12000 rpm. - Operating in counter-rotation. Multi-processing unit 08.348 - For chamfering or radius trimming of the upper and lower longitudinal edges, as well as for copying the front and rear workpiece edges. - Program-controlled adjustment for up to 4 profiles - 2 motors, each 660 W, 400 V, 200 Hz, 12000 rpm. Spray nozzles above and below for applying cleaning agents Multi-profile scraper unit - With stepper motor axes for horizontal and vertical positioning. - For 4 profiles. Straight scraper unit - With electro-pneumatic retraction device Copying edge smoothing unit - With 4 smoothing motors, each 250 W - Smoothing unit with 2 lower and 2 upper motors, each 180 W, 50 Hz, 1400 rpm. Smoothing unit - For smoothing and eliminating the white haze on the trimmed PVC/ABS edges - With an upper and lower smoothing zone With workpiece return system LGIMATECH ZHR 05/L/145 - Air cushion table, inclined, 2 return belts with brushing devices from below. Lhedpozuyhnsfx Abysn Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2019, Edge banding machine Manufacturer: SCM Type: Minimax E10 Year of manufacture: 2019 Technical data Edge thickness (strip material): 0.4 - 3.0 mm Edge thickness with shear cutter at 80 mm edge height: 0.4 - 1.5 mm Edge thickness with shear cutter at 50 mm edge height: 0.4 - 2.5 mm Edge thickness with shear cutter at 45 mm edge height: 0.4 - 3.0 mm Edge height: 10 - 84 mm Workpiece thickness: 8 - 80 mm Minimum workpiece width: 50 mm Minimum edge length: 210 mm Minimum inner radius (concave) at 0.4 mm edge: 25 mm Minimum outer radius (convex) at 0.4 mm edge: 5 mm Feed speed: 4 / 8 m/min Processing temperature: 140 - 220 °C Edge feed Integrated shear cutter for cutting edge material from the roll. Roll table for holding roll material. Suitable for ABS edges, melamine edges, veneer edges, and other pre-fabricated edge strips. Gluing system Ljdpfx Abezuykpsyshn Teflon-coated glue tank below the table top. Continuous glue circulation to prevent glue deposits. Fast heating time of approx. 7 minutes. Standby function with timer. Glue tank capacity: 1.5 liters. Pressure system Motor-driven glue application roller. One free-running pressure roller. Foot pedal for start and stop control of the working cycle. Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: new, Year of construction: 2026, New machine Year of manufacture: 2026 Equipment: Base machine Additional cost for radius milling cutter unit with blowing device + extraction system Additional cost for surface milling cutter unit Additional cost for diamond tools, height = 55 mm, for jointing unit EVA/PUR glue tank with drain function instead of standard glue tank Collection table / pipe bridge Pre-carriage Ledpjzttnfefx Abyjhn Location: Flörsheim Availability: Immediate

Condition: good (used), Year of construction: 2008, machine/vehicle number: 50028, functionality: fully functional, operating hours: 16,000 h, The machine has the following functions: 1. Pre-milling cutters. 2. All lamps are in working order. 3. One container. 4. It has saws that cut forward and backward. 5. It has milling cutters at the top and bottom. 6. It has a rounding cutter for shaping edges. 7. It has a cycling function for processing solid wood. 8. It has a cleaning unit. 9. It has two bottles for cleaning. Lhjdoz H I H Hspfx Abysn

Condition: new, Year of construction: 2026, Feed speed 9 m/min Board thickness 12 - 45 mm Minimum board dimensions (L x W) 90 x 170 mm Worktable height 960 mm Table extension (steady rest) 560 mm Extension connector ⌀ 125 mm Installed power 6.1 kW Pre-milling 3000 rpm Front/back 12,000 rpm Top/bottom 12,000 rpm Polishing 3000 rpm Machine dimensions 3960 x 720 x 1748 mm Ledpszp Nz Hofx Abyehn Weight (net/gross) 800 / 950 kg Feed motor power 0.75 kW Glue tank heater motor power 1.315 kW Pre-milling motor power Milling 1.5 kW Plate heating motor power 0.125 kW Glue spindle motor power 0.25 kW Front/rear cutting motor power 0.37 kW Top/bottom cutting motor power 0.37 kW x2 Corner trimming motor power 0.37 kW Polisher motor power (top/bottom) 0.12 kW x2 (3-phase), 0.18 kW x2 (1-phase) Touchscreen control panel Air consumption 350 L/min Minimum extraction power 5 kW (for effective dust extraction from the edge bander)

Condition: used, Year of construction: 2006, Used Machine Year of Manufacture: 2006 Condition: Completely Overhauled Features and Technical Specifications: - Equipped with a new glue application system - Manually adjustable feed guide - Joining milling unit 1961 - Edge feeder 1903 - Glue application station 1906 with sensing nozzle - Pneumatic pressure unit 1816 - Trimming unit 1822 - Milling unit 1942 M: radius, chamfer, flush - Blowing nozzle, complete - Scraper unit 1929 Lhjdpfx Abozk Nlhoyjn - Chip collection box - Surface scraper 1964 - Exhaust hood set - Protective hoods, complete - Total length: 5291 mm - Workpiece thickness: min. 6 / max. 50 mm - Edge banding thickness depending on configuration: 0.4–5 mm - Max. edge banding height: 55 mm - Edge banding strip length: min. 350 mm - Edge banding overhang/height per side: max. 3 mm - Workpiece width: min. 60 mm - Workpiece length: min. 180 mm - Feed speed: 12.5 m/min - Exhaust: - Jointing unit: 900 m³/h - Milling unit: 280 m³/h - Rake blade unit: 280 m³/h - Static negative pressure: - Joint milling unit: 1490 Pa - Milling unit: 1650 Pa - Min. air velocity: 20 m/sec - Joint milling unit connection: 70 mm - Scraper unit connection: 70 mm - Compressed air: 6 bar

Condition: used, Year of construction: 2018, Second-hand machine Year of manufacture: 2018 Special feature: Machine with a gluing height of up to 100 mm! Condition: factory-inspected by Lange Maschinenbau Features and technical specifications: - Machine table with 13 rollers for improved workpiece guidance - Edge feed, operating in synchronisation with the belt feed - Edge thickness adjustable via digital display - Pneumatic roll separation with blade (for edges suitable for cutting) - three pressure rollers - Belt feed: - 0.25 kW - approx. 1,250 mm long – approx. 6.0 m/min - 50 mm wide toothed belt with a thick rubber lining to protect the workpiece - Digital display for height adjustment - Direct glue application to the workpiece: leak-proof glue tank with glue supply from below and rapid heat-up time after machine shutdown - Flush-trimming unit: - for the front and rear edges of the workpiece - automatic workpiece detection - Pneumatic trimming with a blade for sharp-edged cuts - Flush milling unit - with vertical scanning and horizontal guidance - Reproducible adjustment via digital displays - 2 powerful 0.4 kW high-frequency motors - continuously adjustable from 4,000 to 18,000 rpm - Cutter Ø 70 mm, Z4, radius 2 mm/15° - central extraction connection Ø 100 mm - 2 chip extraction hoods with hose Ø 60 mm - Automatic height adjustment of the upper milling cutter via the belt feed - Workpiece support surface approx. 1800 mm long throughout - Workpiece support rail, extendable by approx. 300 mm - Rotating film tray Ø: 800 mm - Workpiece width: min. approx. 80 mm - Workpiece thickness: 10 – 100 mm - Workpiece length: min. approx. 220 mm - Edge thickness: 0.4 – 2.0 mm - Roll cutting: max. 1.0 x 55 mm, 2 x 45 mm - Glue pan heating capacity: 2.7 kW - Heating-up time: approx. 10 minutes - Working height: approx. 880 mm - Electrical connection: 400 V, 50 Hz, 3-phase + N - Total power requirement: 3.8 kW - Pneumatic connection: 6 bar Lhsdpfxozk Nmrs Abyon Dimensions (excluding film tray): approx. 1800 x 700 x 1300 mm Weight: approx. 260 kg Availability: at short notice Storage location: Flörsheim

Condition: used, Year of construction: 1983, Used machine Year of manufacture: 1983 Features and Technical Specifications: - For pre-coated edge banding material - Edge banding material up to 1.3 mm - With roll trimming - With flush trimming using a blade - With top and bottom flush milling/bevel milling using HF motors Location: Röllbach Lhjdpfxszk Ntls Abysn Availability: Available shortly

Condition: used, Imatronic Numerical Control with ImaWop 8.0 Software (software updated in 2020) Working range on X axis mm 7000 Working range on Y axis mm 1400 Full table with support panel for positioning the suction cups Suction cups can be manually positioned on the work surface using a laser indicator No. 2 vertical electrospindles with C axis with automatic tool change Automatic tool changer with 18 positions on the back of the machine Drilling head with 21 spindles arranged as follows: * N° 11 verticals on X axis * N° 10 verticals in Y axis Edgebanding unit with glue pot and pre-melter for EVA glue (glue pot new in 2023) Nordson pre-melter for PUR bonding on Folding panels No. 1 blade aggregate (end cutter) No. 1 trimming aggregate No. 1 cross-shaped aggregate with 4 horizontal drilling lines No. 1 blower aggregate 2-position edge storage unit Front protection and safety system with carpets Full protection cabin (not original IMA) TECHNICAL DETAILS TO BE CHECKED Lhsdpfow El Nhjx Abysn

Condition: new, Year of construction: 2026, Edge thickness 0.4 - 3 mm Thickness of glued boards 10 - 45 mm Minimum length of glued boards 80 mm Minimum width of glued boards 60 mm Mechanical feed speed 8 / 11 / 13 m/min. Glue temperature 185 - 210 ℃ Tank capacity 2.5 - 3 kg Pre-milling head speed, main 12,000 rpm Rounding radius R=2mm Working pressure compressed air pressure 6 - 8 bar Pre-milling unit 1.8 kW x 2 Glue application roller unit 0.75 kW Glue heating unit 1.5 kW Final milling unit 0.37 x 2 kW Main milling unit 0.75 kW x 2 Corner milling unit 0.75 kW Transport belt unit 1.5 kW Lhodpev Dt T Hofx Abyon Overall dimensions 4500 x 700 x 1450 mm Transport dimensions 4280 x 650 x 1280 mm Weight 1230 kg Pre-milling milling: diamond milling cutter. Gluing Final cutting Milling: two motors Corner finishing Radial scraper Flat scraper (glue) Spray system Polishing Internal lighting Automatic lubrication Electrical equipment: Delta brand

Condition: new, Year of construction: 2026, min. / max. veneer thickness 0.4 - 3 mm min. / max. veneer height 12 - 47 mm (optional: veneering up to 60 mm) min. / max. material height 10 - 45 mm min. material width 100 mm min. material length 100 mm material pre-milling 2 motors with power (diamond cutter) 2.2 kW feed motor power 2.2 kW panel desk at eye level : chain feed : loading plate for PVC and ABS edges : mechanical pressure zone driven by the main pressure roller and a series of pressure rollers to minimize the glue layer : central pressure setting : container for glue granulate : glue application to the material using a glue roller : electronic temperature control, working temperature 180 - 200 °C pneumatic tape cutting guillotine : control lamp for element spacing : double trimming saw for cutting off front and rear excess material : precise linear guides : trimming in motion for high cutting precision : veneering speed 9.5 m / min flat and round milling top / bottom with vertical and horizontal guidance 2 x 0.55 kW, 12,000 rpm. scraper unit: polishing unit top / bottom 2 x 0.18 kW, 50 Hz, 2,800 rpm. height and tilt adjustment: extraction connector 3 x fi 120 mm, 1 x fi 100 mm, roller table extension 250 mm: noise-reducing housing with a window to view the units: trimming unit 0.44 kW glue roller unit 0.55 kW Ledpfxjv Dutbo Abyjhn glue tank heater 2.2 kW compressed air connection 6.5 bar total power consumption 9 kW / 400 V dimensions L. 3590, W. 1220, W. 1686 mm weight 1100 kg • Pre-milling with counter-milling cutters placed on heads ensuring the highest quality of processing. • Front and rear cutting with a double saw. Upper and lower milling on a separate cutter. • Radial or flat scraper (to choose from). -polishing unit • Equipped with a control computer with an LCD display. • Very simple operation with switching on/off individual units with a single button. • In a word, an ergonomic and precise machine at a very favorable price offer, unmatched on the global market. • Standard function of a replaceable glue tank.

Condition: used, functionality: unexamined, Ferwood Code: RU0002552 - Manufacturer Code: 4-008-39-1708 - Condition: Used - Functionality: Not tested - Compatible Machine: HOMAG EDGEBANDER - If interested we offer a revision service, contact us. Lhsdsv Dvg Aspfx Abyjn

Condition: new, Year of construction: 2023, New machine Year of manufacture: 2023 Single-sided automatic edge banding machine with pre-milling unit, hot-melt adhesive application on straight workpieces (EVA/PUR glue pot with emptying function optional), HF cross-cut saw station, HF milling unit, corner copying unit, chain feed, double roller upper pressure, extendable workpiece support rail, signal lamp for workpiece tracking and integrated length control for contactless operation of processing functions. Suitable for ABS, PVC, melamine, and solid wood veneer edging coils, as well as fixed lengths from 0.4–3.0 / 6.0 mm and workpiece heights from 8–60 mm. Feed speed: 10.0 m/min; 8.0 m/min with corner copying. ● 3 free slots for finishing units ● 10" color touch screen. Machine length: 4030 mm Workpiece thickness: 8–60 mm Min. workpiece width: approx. 75 mm Min. workpiece length: approx. 120 mm (min. approx. 200 mm with corner copying) Edge thickness: 0.4–3.0 mm Pre-milling unit chip removal: 0–2.0 mm, stepless adjustment Total connected load: 7.5 kW – 400 V Feed speed: 10 m/min; 8 m/min Pneumatic connection: 6 bar Net weight: 1050 kg Options: Ledpfjw I U Drox Abyjhn Surcharge for radius scraper unit with air nozzle + extraction Surcharge for surface scraper unit + extraction Surcharge for buffing unit EVA/PUR glue pot with emptying function Surcharge for diamond tools, height = 65 mm for pre-milling unit Riepe spray system (anti-adhesive) at the pre-milling unit Riepe spray system (cleaning spray before buffing unit) Pipe system with 90° bend + manual slide valve, installed on machine, D=200 mm Availability: short-term Location: Hochheim

Year of construction: 2024, condition: new, Return System Year of manufacture: 2024 The RTS Compact is a standalone system that can be connected to any edgebanding machine (KAM), regardless of the manufacturer. The feed speed is continuously adjustable to match the speed of the edgebander. The RTS Compact is supplied complete with a control cabinet and is ready for operation immediately after installation. Optional: "RTS Compact Conveyor Extension" for easy rotation of parts during cross-edge banding. Optional: "RTS Compact Ergonomics Package" available. A lift table and air cushion table are used at the end of the return conveyor. This option enables ergonomic operation. - Compatible with edgebanders from all manufacturers - Allows single-operator control of the edgebander - Maximum ergonomics - Reduced personnel costs - Gentle material handling - Installation time approx. 0.5 day - Turning device for small parts - With conveyor belt L 4500 x W 800 mm Single-track roller rail Lhsdpfx Absw Nadmsyon RTS Compact control, optional control box Availability: short-term Location: Flörsheim

Condition: used, Year of construction: 2000, machine/vehicle number: C/62702, functionality: fully functional, operating hours: 1,660 h, workpiece height (max.): 42 mm, edge thickness (max.): 8 mm, height adjustment type: electric, actuation type: electric, total height: 1,550 mm, total length: 5,750 mm, total width: 1,050 mm, overall weight: 2,200 kg, Equipment: CE marking, OTT Pacific is a series of industrial edge banding machines (machines for applying and processing edge strips) from the Austrian manufacturer Paul OTT GmbH. Key features and specifications: Purpose: Precise processing and bonding of ABS, PVC, wood, or veneer edge strips onto wood panels. Compact design: The total length of the machine is approximately 5.5–5.7 meters, allowing it to be installed in smaller workshops. Edge strip thickness: Processes edge strips with a thickness of 0.3 mm to 15 mm (in classic V6 models, up to 6 mm). Workpiece thickness: Panels with a thickness of 8 mm to 42 mm. Feed rate: Between 12 m/min and 18 m/min. Popular models in the series: OTT Pacific V6 / V6-F: A classic and widely used model with grooving cutters (the F designation) and processing of edge strip thicknesses up to 6 mm. Lhedozi E Szspfx Abyon

Condition: excellent (used), functionality: fully functional, pre-milling aggregate granulate glue station maximum working height 60 mm guillotine for trimming edge band from the roll Lsdpfxezlc H Ue Abyshn precision edge band trimming unit milling aggregate for trimming edge band excess from the top and bottom of the panel profile scraper flat scraper polishing units machine length 420 cm year of manufacture 2012 CE mark

Condition: excellent (used), SINGLE SIDE EDGE BANDER (Left) Edges (band in rolls) thickness (Min/Max) mm 0,3 / 3 Lhjdpfozku Rpsx Abyon Edges thickness in strips / lippings (min/max) mm 0,4 / 20 Panels thickness (min/max) mm 8 / 60 Numerical Control POWER CONTROL PC23 Powertouch / WoodCommander (TAPIO Ready) Feeding speed m/min 16-25 Top pressure system with rubber belt Spraying unit (Anti-sticking liquid) In-feed fence, adjustable by N.C. Pre-milling Unit (vertical joint trimmers) 2 x Kw 3 Lamps to heat the workpieces side Glueing Unit (Hot Melt + Quick Melt Unit) FE-MA-TECH + QA/PU + PU65 Band Pressure zone (N.C. adjustment) "C 7" Edge coils supporting unit (No. 2 reels) with SERVO-control edge feeding Snipping (end-cutting) unit PK 25 (2 x Kw 0,8) max 25 m/min Rough Trimming unit BF20 (2 x Kw 1,5) Fine Trimming unit (Multiprofile) MF21 (2 x Kw 0,55) swevelling 0°-20° Multi Function Unit (Profile contour Trimming unit) FK 30/V20 (1 x Kw 0,7) adjustable by NC Milling-grooving units SF 21 (1 x Kw 5) 0°-90° Profile edge scraping unit MN 21 (Multiprofile, by N.C.) Glue scraping Unit FA 20 Buffing unit FA06 (2 x kW 0,18) + Free Space

Condition: used, Holz Her Sprint 1312 FÜ + PU Heavy-duty design – edge thickness 0.4 - 12 mm PLC screen control Pre-milling unit for application before the gluing section Fully automatic edge magazine for roll and strip material Glue application station for cartridges + PU bonding automatic tracing nozzle Workpiece height 6-55 mm End trimming unit for roll and strip material up to 12 mm edge thickness with adjustment from 0-10° angle of the trimming saws Milling unit, flush milling up to 12 mm, radius milling – bevel milling - 15° motorised - 4 axes Scraper unit for bevels and radii with 2 pneumatically operated scraper holders pneumatic infeed and outfeed Lhedpfx Aex Eilqebyen Flat scraper unit – finishing Spray device – PU Machine in TOP CONDITION Available from stock Lieboch

Condition: used, Year of construction: 2014, For inquiries: Zoltán Utasi +36 30 205 7380 • motorized pressure bridge adjustment • Electrical system for stepless feed 400 V / 50 Hz, 2.2 kW • “Control PPC 221 – with 8.4'' VGA color display” High-performance control with very simple operation • Edging pre-milling unit 1802, 400 V (2 x 2.0 kW, 200 Hz, 12,000 rpm) with 2 milling units for pre-milling the panel edge • Cutter, diamond Ø 70 x 64 x 30 mm, Z2, left-hand rotation For pre-milling unit 1801 / 1802 • Cutter, diamond Ø 70 x 64 x 30 mm, Z2, right-hand rotation For pre-milling unit 1801 / 1802 • Edge feeding unit 1903 SYNCHRO Lhsdpfx Asx Huhcebyon automatic transport of rolls and strip material • Glue application station Glu Jet GJ301 automatic (2.3 kW, 50 Hz) • Pressure unit 1913 pneumatic first roller driven, 2 additional pressure rollers with pneumatic individual control • Cut-off unit 1918 (60 mm) pneumatic (2 x 0.45 kW, 12,000 rpm) pneumatically swivelable 0/10° • Multifunction milling unit 1827 pneumatic (2 x 0.65 kW, 200 Hz, 12,000 rpm) • Vertical tracing rollers manual manual adjustment of the vertical tracing roller by 0.1 mm for milling edge overhang, e.g. for plastic edges • Cutter, diamond Ø 56 / 60 mm, Z = 2, R = 2.0 mm, left-hand rotation Diamond-coated, solid tool with CM technology (LEUCO system) with integrated chip extraction, patented ProLock-E • Cutter, diamond Ø 56 / 60 mm, Z = 2, R = 2.0 mm, right-hand rotation Diamond-coated, solid tool with CM technology (LEUCO system) with integrated chip extraction, patented ProLock-E • Corner copying unit 1832 (1 x 0.35 kW, 200 Hz, 12,000 rpm), for edge thickness up to 3 mm • Cutter, diamond Ø 53 mm x 10 mm x 16 mm, Z = 3, R = 2 mm, with CM technology (LEUCO system) with integrated chip extraction, for profiling unit 1832 • Scraper unit 1929 pneumatic including pneumatic adjustment (separately for top and bottom) • HW reversible knives for scraper holder 1929 / 1927 R = 2.0 mm (2 pcs required) • Flat scraper unit 1964 Removing glue residue for a clean glue joint. • Buffing unit 1940 (2 x 0.12 kW, 50 Hz, 1400 rpm) For final cleaning and edge polishing. With 2 textile discs, swivel range 0–5°