Used Compounding Extruder for sale (585)

Condition: ready for operation (used), Year of construction: 1995, operating hours: 39,000 h, functionality: fully functional, Equipment: documentation/manual, A used and functional profile line for rigid PVC-profiles (300 x 100 mm), consisting of: Twin-screw extruder (parallel) Manufacturer: WEBER Type: DS 7.22 Year of manufacture: 1995 Machine no.: DS70-043 Operating hours: 39,000 hours Screw diameter: 70 mm Effective screw length: 22 x D Screw geometry: for rigid PVC profiles Torque: 4,500 Nm per screw Screw speed: max. 40 rpm, continuously adjustable Drive motor: DC low-voltage motor, thyristor-controlled Drive power: approx. 25 kW Cylinder heating/cooling zones: 5/3 (air cooling with fan) Adapter heating zone: 1 Tool heating zones: 5 Control: conventional control with digital temperature controllers Degassing: Busch rotary vane vacuum pump (1.5 kW) Output capacity, max.: 120-150 kg/h for hard PVC, depending on material Connected load: approx. 50 kW (without tool) Special accessories: Mass temperature sensor and mass pressure sensor Adapter between extruder connection and extrusion tool Used tool set for a window profile (widening), consisting of: - Extrusion tool ‘widening’, incl. heating bands Lodpfx Aeyhcabjbyoru - Dry calibration - Vacuum tank approx. 2 m long, with 8 slots for calibration discs - 16 calibration discs Vacuum calibration unit Manufacturer: Uniplast / Greiner Type: CAL VAK 4P Year of manufacture: 1992 Machine number: K9209590 Total length: 6500 mm Vacuum pumps: 4 x Speck vacuum pumps (4.3 kW each) Water circulation pumps: 2 x Calpeda (1.1 kW each) Caterpillar haul-off, incl. attached saw Manufacturer: Uniplast / Greiner Type: CAT PUL 2D Year of manufacture: 1992 Machine number: R 9204546 Haul-off: Effective contact length: 2000 mm Pad width: 250 mm Haul-off force, max.: approx. 25000 N Speed range: approx. max. 10 m/min. Profile saw: HM circular saw blade: Ø 450 mm Profile cross-section, max.: approx. 300 x 100 mm Tilting table Manufacturer: Ide Type: ME N 52/2 Year of manufacture: 1994 Length: 6000 mm Support width: 270 mm Note: The complet profile line was overhauled in 2020 and has only been in operation for 325 hours since then.

Condition: like new (used), The system is a complete surf finisher system including suction station + undersize screening station + complete water treatment + water tank from Rösler. If required, including robot + handling portal. The components are transferred by robot to a portal with holders and immersed in the rotating surf container. The deburring performance is 20 seconds. Immersion time corresponds to about the same performance as 10-15 minutes. in a conventional vibratory finishing machine. Rotating work tank RMSF 4/800 1 piece round plastic container - Working tank diameter: 850 mm Working tank depth: 500 mm 1 pc. quick coupling for easy changing of the working container 1 pc. drive motor, power 7.5 kW 1 pc. dosing device D1-K/320 SF (circulating water) on stand 1 pc. stand for enemas in the working container 1 piece flow monitoring (by means of flow monitor) Undersize screening: 1 pc. Grinding wheel return system 1 piece underframe as a stable welded construction 1 pc. balancer for weight compensation (sanding pad + hose + nozzle) including mounting frame - Suspension for hose on the base 1 pc. vacuum generator for generating a negative pressure - Connection of the line system to the transfer device of the vibratory finishing system - Suction hose with nozzle, length approx. 5 m 1 piece collection container 500 liters as a cyclone separator - for receiving the process media that are sucked out of the working container, - for delivering the process media to the screening machine - incl. automatically operated gate valve and hose for returning the process media to the screening machine 1 pc. spray nozzles for rinsing out the collection container 1 pc. 2-hand control for flap 1 pc. dosing device DZ1-K Rösler screening machine R 12/6 SM-E - for undersize screening - Total length: 1,400 mm - Overall width: 1,160 mm - Screen area: 1,200 x 600 mm - Delivery height: 1,065 mm Lrsdpfx Aboyngiteyeu - Step in the separation zone: 1 x 40 mm - Drive power of vibration motors 2 x 0.525 kW - Vibration motors arranged laterally - Engine speed: 1500 rpm - Operating voltage: 400 V, 50 Hz, 3 Ph N/PE Rösler centrifuge Z 1000 ASS-II-Turbo with automatic sludge discharge consisting of: Centrifuge Z 1000 * Aluminum alloy centrifuge rotor * Speed: 2,050 rpm * Reduced stripping speed via frequency converter * automatically retractable paring knife * Amount of sludge per peeling cycle: up to 25 kg * automatic residual water drainage * Long bearing service life due to special bearings that can be relubricated * electronic vibration monitoring * automatic rotor flushing Accesories 1 piece mud truck RSKM 30 1 pc. Combined waste water and circulation tank 700/700 liters 1 pc. flocculant dosing pump DP2 1 pc. Automatic post-dosing DZ-4/320 2 suction lances (vacancy monitoring) 1 pc. sound insulation package approx. 80 dB(A) 1 piece cooling unit RK 3 1 piece titration measuring kit for manual compound measurement

Condition: used, Year of construction: 2019, gebraucht 2019 5505 prompt, Zwischenverkauf v Niederlande 2670 € 1 100 x 2.000 mm 20 - 76,1 mm Lrjdpfx Abswiqwleyju 1 3 kW 190 kg DEMO MACHINE / MINT CONDITION The lever operated AL100U-01 can grind material from Ø 20 mm to Ø 76.1 mm. Its compound slide and carriage with rotatable clamp are continually adjustable allowing the machine to grind all pipe sections at any angle between 30° and 90°. The ALMI AL100U-01 can be used to grind square, rectangular and round pipes with a range of wall thicknesses and is suitable for all customary types of materials. ALMI’s belt tensioning system simplifies tensioning the grinding belt. The belt is tensioned using the hexagonal spanner supplied with the machine. The grinding belt can be tensioned quickly and the grinding rollers can be changed in seconds. All pipe grinders are equipped with a deburring table. Incl. 5 pcs. grinding belts, 1 pce. grinding roll Ø. 42,4 mm BUYING USED MACHINERY IS A MATTER OF TRUST - OUR TRANSPARENCY PROMISE We offer you maximum security and complete transparency. • HONEST INSIGHTS: Detailed photos and functional videos of the current condition • LIVE ON-SITE CHECK: Live testing is possible at our facility • DIGITAL DEMONSTRATION: Individual live demonstration via video call • RISK-FREE PURCHASE: 14-day return policy Details:

Condition: new, neu ca. 2 Wochen ab Auftragse Niederlande 4785 € 100 x 2.000 mm 20 - 76,1 mm 1 1 3 kW 220 kg The AL100U-02 can be operated with two hand-wheels or a lever. The machine is equipped with both options. The AL100 U-02 can grind material from Ø 20 mm to Ø 76 mm. The compound slide and carriage with rotatable clamp are continually adjustable, which means the machine can grind all pipe sections at every required angle between 30° and 90°. The ALMI AL100U-02 can be used to grind square, rectangular and round pipes with a range of wall thicknesses and is suitable for all customary types of materials. ALMI’s belt tensioning system makes tensioning the grinding belt even easier. The belt is tensioned using the hexagonal spanner supplied with the machine. The grinding belt can be tensioned quickly and the grinding rollers can be changed in seconds. All pipe grinders are equipped with a deburring table. Ledpfx Ajwir Dmebyoru Incl. 5 pcs. grinding belts, 1 pce. grinding roll Ø. 42,4 mm

Condition: good (used), functionality: fully functional, power: 52 kW (70.70 HP), nominal power: 45 kW (61.18 HP), overall weight: 330 kg, For sale: AEG AM225M4 Electric Motor – 45 kW Location: Ivanka pri Nitre, Slovakia Price: 1,000 EUR Lrodpoxvq Dvefx Abysu Used three-phase electric motor, type AEG AM225M4, rated at 45 kW / 400 V / 50 Hz (52 kW at 60 Hz). The motor is in good mechanical condition and has been stored indoors. Suitable for industrial applications, pumps, extruders, or general heavy-duty machinery. Inspection possible by appointment. Contact for more information or photos.

Year of construction: 2004, condition: excellent (used), functionality: fully functional, SICA SOCKETING MACHINE BA.2F.1T. 63-315 Application: KG-U PVC pipes, Pipe lengths: 0.5m, 1m, 2m, 5m, 6m Year of manufacture: 2004 1 socket per cycle Lodpfxoxiy Nus Abyjru Socket tool: 160x4.6 The socketing machine is in very good condition, still in operation, and will be removed from production in 3-4 months.

Condition: new, Year of construction: 2025, Premade pouches packaging/filling and closing machine, rotary operation with 6 working positions. Suitable for flat pouches and doypack style pouches. Easy operation through touch screen and SIEMENS PLC, frequency conversioin for speed adjustment, no-pouch- (or no open pouch) no-filling/seal function. Motorized bag width adjustment, oil free plastic bearings, all product or bag contacting parts are made of stainless steel (SS304). Can be used with all kinds of infeed/dosing modules (optional) to pack granulate like products, liquids, pastes, powdes, etc. Suitable for a wide range of film materials like compound/monolayer PE, PP, paper, etc. (please ask for details). Bag infeed vertically with hopper (for flat bags), optionally: horizontally infeed. Sucking unit to open all kind of bags with thinner film material. Suitable for the following bag dimensions: L(100-350)xW(100-210)mm. - Technical specifications: max. speed of the machine in neutral: 45 cycles/minute; power: 380V, 2.5kW; compressed air: 0.6m³, 6bar; machine dimensions: L2214xW1850xH1640mm; weight: 1000kg. That machine/system is available in different versions for different packaging sizes and with different packaging speeds. Lsdev Nlmcepfx Abyjru Please note that our new prices are often below the usual used prices. Please feel free to inquire and tell us your packaging task. - Usually 30-50 different new machines are available immediately from stock. In addition, we have very short delivery times from approx. 3 weeks for customized machines. Deviations from the sample photo are possible. - All machines are available with full warranty.

Year of construction: 2025, condition: new, Premade pouches packaging/filling and closing machine, rotary operation with 8 working positions. Suitable for flat pouches and doypack style pouches with/without zipper or spout. Easy operation through touch screen and SIEMENS PLC, frequency conversioin for speed adjustment, no-pouch- (or no open pouch) no-filling/seal function. Motorized bag width adjustment, oil free plastic bearings, all product or bag contacting parts are made of stainless steel (SS304). Can be used with all kinds of infeed/dosing modules (optional) to pack granulate like products, liquids, pastes, powdes, etc. Suitable for a wide range of film materials like compound/monolayer PE, PP, paper, etc. (please ask for details). Bag infeed vertically with hopper (for flat bags), optionally: horizontally infeed, especially for zipper or spout bags. Sucking unit to open all kind of bags with thinner film material. Suitable for the following bag dimensions: L(100-350)xW100-210)mm. - Technical specifications: max. speed of the machine in neutral: 45 cycles/minute; power: 380V, 3.0kW; compressed air: 0.6m³, 6bar; machine dimensions: L2500xW1800xH1800mm; weight: 1100kg. Lredpfev Nlmpsx Abyou That machine/system is available in different versions for different packaging sizes and with different packaging speeds. Please note that our new prices are often below the usual used prices. Please feel free to inquire and tell us your packaging task. - Usually 30-50 different new machines are available immediately from stock. In addition, we have very short delivery times from approx. 3 weeks for customized machines. Deviations from the sample photo are possible. - All machines are available with full warranty.

Year of construction: 1994, condition: excellent (used), SICA-TRS 110-800.D Pipe Saw for PVC Pipes/PP/PE Application: Cutting and chamfering PVC, PE, and PP pipes With chip extraction fan Min. diameter 110 mm Max. diameter 800 mm Year of manufacture 5/1994 Accessories: Various clamping jaws Lredpfsvulgtex Abyeu Machine locations: Sachal Extrusionsmaschinen D-26345 Bockhorn-Grabstede Bahnhofstraße 6 The machine is my property

Condition: excellent (used), functionality: fully functional, Enhanced finishing solution for metal 3D printed components EXTRUDE HONE technology opens the door to a very economical, fast, controllable, flexible, and environmentally friendly process for enhanced surface finishing of metal 3D-printed parts. We have a used machine in stock for immediate delivery. This machine has only been used briefly and is in excellent condition. FEATURES and BENEFITS + Efficiency in enhanced surface finishing. Material removal rate (μm/min) faster than other methods on the market; e. g. up to 3 times faster than electro-polishing. + Tooling out of the printer. Tooling and fixtures are built at a reasonable cost since they are 3D-printed. Lredpfx Aev Awrwsbyou + Highest flexibility. We provide a complete & optimized cathode and fixture design for your components within two working days. + Multiple material master packages Specific parameter files per alloy family. + EXTRUDE HONE Connect From CAD to part, remotely: loading of parameters, upgrading material packages, software, and maintenance. + Make it easy. The all-new and simple operating concept limits the data input to 4 simple parameters – parameters everybody understands.

Condition: ready for operation (used), Year of construction: 2021, overall weight: 97 kg, travel distance X-axis: 300 mm, travel distance Y-axis: 200 mm, travel distance Z-axis: 200 mm, number of axes: 3, This 3-axis DESKTOP METAL Metal Studio 2 was manufactured in 2021. It utilizes Bound Metal Deposition technology and features a build volume of 300 x 200 x 200 mm. The machine supports various materials, including 316L and H13 Tool Steel, and operates with a dual extruder system. If you are looking to get high-quality metal 3D printing capabilities, consider the DESKTOP METAL Metal Studio 2 machine we have for sale. Contact us for further details. Lrsdpfsyuyz Nsx Abyeu • Technology: Bound Metal Deposition (BMD) • Process: 2-step (printing and sintering – no debinder needed) • Build volume: 300 x 200 x 200 mm • Layer height: 50 µm to 250 µm • Build plate: Heated up to 120°C (vacuum-adhered) • Extruders: Dual (metal and ceramic support) • Support interface: Ceramic release layer (manual breakaway) • Materials: 316L, 17-4 PH, 4140, H13 tool steel, copper • Software: Fabricate (automated scaling and sintering profiles) • Connectivity: WiFi / Ethernet Additional equipment • Furnace: Max temperature 1400°C; atmosphere: partial pressure Synthogas (Ar/H2); sintering cycle: 16–24 hours

Condition: used, Year of construction: 1993, operating hours: 57,000 h, functionality: fully functional, rotational speed (min.): 1,413 rpm, input voltage: 400 V, Industrial DC Electric Motors 481 kW – IEG / Ansaldo Available: 2 high-power industrial direct current (DC) electric motors, manufactured by IEG Trieste – Ansaldo Industria, designed for heavy-duty industrial applications. The motors have been dismantled from an industrial plant and are in excellent condition, complete with dedicated ventilation systems and control panels. Ideal for the revamping of existing plants, rolling mills, extruders, large fans, hoisting installations, or other industrial high-torque applications. Main technical data: Manufacturer: IEG Trieste – Ansaldo Industria Type: Direct current (DC) motor Power: 481 kW Voltage: 400 V Rated current: 1530 A Speed: 1413 rpm Duty: S1 continuous Excitation: 220 V Year of manufacture: 1993 Operating hours: approx. 57,000 Lrodoytgk Ispfx Abyou Equipment included: - Dedicated ventilation system - Electrical control and command panels - Technical documentation available On-site inspection possible

Condition: new, Year of construction: 2026, functionality: fully functional, turning diameter over cross slide: 250 mm, turning length: 1,000 mm, turning diameter: 400 mm, spindle bore: 52 mm, spindle speed (max.): 1,810 rpm, spindle speed (min.): 65 rpm, spindle motor power: 2,200 W, total height: 1,650 mm, total length: 1,900 mm, total width: 830 mm, type of input current: three-phase, overall weight: 790 kg, Equipment: documentation/manual, Universal Lathe TORNADO 400 × 1000 – 2.2 kW / 400 V With Digital Readout and Work Light Key Features Precision spindle roller bearings The spindle is equipped with high-precision roller bearings that ensure excellent machining accuracy and reliable operation even during intensive use. High-quality hardened and ground steel gears in the headstock transmission All gears inside the headstock are made from high-grade steel, hardened and ground to ensure smooth, quiet operation and long service life. Easy and quick gearbox operation The intuitive gearbox design allows quick and convenient speed changes and easy adjustment of machining parameters. Powerful drive motor The machine is equipped with a sufficiently powerful motor that ensures stable performance even under heavy loads. D1-5 spindle mounting system The D1-5 camlock spindle system allows quick and secure installation of chucks and other accessories. Wide range of thread cutting capabilities The machine enables cutting of various thread types (metric, inch, module, and others), making it a versatile tool for many applications. Technical Specifications Turning Capacity Maximum swing over bed: 400 mm Swing over cross slide: 250 mm Swing in gap: 520 mm Distance between centers: 1000 mm Maximum workpiece length (chuck + tailstock): ~920 mm Slides and Travels Compound slide travel: 125 mm (0.02 mm accuracy) Cross slide travel: 240 mm (0.04 mm accuracy) Longitudinal travel: 750 mm (0.2 mm) Drive and Speeds Main motor power: 2.2 kW / 400 V Coolant pump power: approx. 40 W Spindle speeds: 18 ranges (I/II) 65 – 1810 rpm Threads and Feeds Metric threads: 0.4 – 7 mm Inch threads: 4 – 60 T.P.I. Module threads: 0.4 – 3 mm D.P. threads: 8 – 84 D.P. Longitudinal feed range: ~0.053 – 1.291 mm/rev Cross feed range: ~0.011 – 0.276 mm/rev Construction and Spindle Bed width: 218 mm Spindle bore: 52 mm Spindle taper: MT6 Spindle nose: D1-5 CAMLOCK Tailstock: Quill diameter: 50 mm Quill travel: 110 mm Taper: MT4 Dimensions and Weight Machine dimensions (L × W × H): approx. 1900 × 830 × 1650 mm Weight: approx. 640 – 790 kg (depending on configuration) Standard Equipment 2-axis digital readout (optical scales) 3-jaw chuck 200 mm + internal jaws set 4-jaw chuck 200 mm Faceplate 280 mm Steady rest Follow rest Lrodjyr Ihlepfx Abyju Dead centers MT4 – 2 pcs. Spindle reduction sleeve MT6 / MT4 Change gears set Coolant system Working light Lubrication pump Chuck key and toolpost wrench Set of service tools Safety guards compliant with CE standards Operating manual (English) CE Declaration of Conformity Delivery to the customer is possible. Shipping cost is calculated individually by the transport company.

Condition: new, Year of construction: 2024, functionality: fully functional, machine/vehicle number: 20250108, total height: 2,200 mm, overall weight: 700 kg, total length: 1,700 mm, total width: 1,300 mm, type of input current: three-phase, workpiece weight (max.): 75 kg, tank capacity: 120 l, usable tank capacity: 60 l, input voltage: 400 V, rotational speed (min.): 50 rpm, rotational speed (max.): 180 rpm, power: 4 kW (5.44 HP), input current: 16 A, warranty duration: 12 months, Equipment: rotational speed infinitely variable, The Turbo-Line 120 “S” model has a stainless steel ejection box mounted directly on the deburring machine. When the bowl lowers, the chips fall through a grid while the parts to be deburred remain on top. This Turbo-Line machine includes a Ljdpfx Absvvu Sneyeru 120-litre drum with vertical, straight sides and a separate base that rotates at an adjustable speed, normally between 115 and 135 rpm, but adjustable from 50 to 180 rpm. During operation, the grinding bodies inside the bowl create a uniform, spiral movement reminiscent of a twisted sausage. All areas of the machine that come into contact with the product, including the drum and the base, are coated with at least 26 mm of yellow polyurethane (PU) to ensure a long service life. The 120 liter work bowl can process up to 50-60 liters of product per batch, depending on the shape and size of the parts. The deburring parameters such as time and speed are individually controlled via a manual touch screen. The addition of water and compound is done via a manually adjustable ball valve, which is included in the delivery. The finished products are discharged by tilting the bowl, a process controlled via the touch screen. The emptying speed is also adjustable via the frequency converter on the touch screen.

Condition: new, Year of construction: 2026, Industrial Universal Lathe CORMAK GOLIAT 660 × 4000 mm The CORMAK GOLIAT 660 × 4000 is a heavy-duty industrial universal lathe designed for demanding turning applications. With a 4000 mm distance between centers and a 105 mm spindle bore, the machine enables precise machining of large-size components while maintaining high rigidity and accuracy. It is an ideal solution for production plants, repair workshops, and companies specializing in the regeneration of machine parts. Main Features of the Machine 4000 mm distance between centers and 3950 mm turning length – designed for machining long shafts, pipes, and large components. Large 105 mm spindle bore – enables efficient machining of large-diameter workpieces. Heavy-duty cast iron bed – hardened and precisely ground, providing excellent resistance to twisting, vibration, and deformation. 3-axis digital readout system – ensures accurate control of carriage and slide positions. High-quality spindle bearings – guarantee smooth operation, stability, and long-term precision. Rapid feed system – longitudinal rapid feed of 4.5 m/min and cross rapid feed of 1.9 m/min significantly reduce machining time. Removable bed gap section – allows turning of oversized components with diameters up to 870 mm. Direct thread selection – enables quick adjustment of threading parameters without changing change gears. Precision and Functionality The CORMAK GOLIAT 660 × 4000 conventional metal lathe provides a wide range of machining operations, including external and internal turning, metric, imperial, module, and DP threading, drilling, broaching, and taper turning. Standard Equipment 3-axis digital readout system (optical scales) Self-centering 3-jaw chuck, 320 mm Independent 4-jaw chuck, 400 mm Faceplate, 400 mm Rapid feed system Fixed steady rest Follow rest Two fixed centers MT5 Spindle reducing sleeve Coolant system Work lighting Chuck and tool post keys Complete set of operating tools Operating manual CE Declaration of Conformity Technical Specifications Parameter Value Maximum turning diameter over bed Ø660 mm Maximum turning diameter over cross slide Ø420 mm Maximum turning diameter in bed gap Ø870 mm Bed gap length 240 mm Distance between centers 4000 mm Maximum turning length 3950 mm Spindle bore Ø105 mm Spindle taper diameter and angle Ø113 mm, 1:20 Spindle nose D1-8 CAMLOCK Spindle speeds 12 speeds (36–1600 RPM) Longitudinal feeds 65 ranges (0.063–2.52 mm/rev) Cross feeds 65 ranges (0.027–1.07 mm/rev) Metric threads 22 ranges (1–14 mm) Imperial threads 25 ranges (28–2 TPI) Module threads 18 ranges (0.5–7 mm) DP threads 24 ranges (56–4 DP) Ljdpfx Abjvw Abgoyjru Rapid longitudinal feed 4.5 m/min Rapid cross feed 1.9 m/min Lead screw pitch 12 mm Spindle axis height above tool surface 28 mm Tool size 25 × 25 mm Maximum compound slide travel 145 mm Maximum cross slide travel 380 mm Tailstock quill diameter 75 mm Tailstock taper MT5 Maximum tailstock quill travel 150 mm Tailstock lateral adjustment ±15 mm Main motor power S1/S6 7.5 / 9 kW, 400 V Rapid feed motor power 250 W Coolant pump power / flow rate 60 W / 25 l/min Machine dimensions (L × W × H) 5500 × 1100 × 1450 mm Machine weight 5200 kg

Condition: new, Year of construction: 2025, functionality: fully functional, Equipment: lighting, Modern painting systems and drying rooms must meet higher requirements than just a few years ago. The use of new coating systems, such as hydro-based paints, polyurethane resins, and epoxy-zinc powder or epoxy-iron glitter paints, demands advanced paint room solutions. A key aspect is the workpiece transport to the painting system and further processing. Our engineers offer expert guidance, whether it's dry overspray removal, wet washing, air humidification, or air drying, condensation drying at low temperatures, or hot air drying. We also provide pre-treatment solutions such as high-pressure washing with water circulation systems or compressed air blasting or wheel blasting techniques. Key Components of a Modern Painting System: Painting Booth: The key element of our system, equipped with advanced air filtration and ventilation systems to ensure a dust-free environment for top-quality results. 🎨 Air Treatment: Essential for maintaining the air balance in the spray booth by drawing in filtered air to replace the air exhausted by the ventilation system. 🌬️ Exhaust System: Removes overspray and volatile organic compounds (VOCs) from the booth, ensuring good air quality and operator safety. 🌿 Drying & Curing Oven: After painting, parts are transferred to the oven to cure and obtain a durable, high-quality surface. 🔥 Conveyor System: An automated conveyor moves parts from the spray booth to the oven, ensuring efficiency and consistency. 🚜 Control Panel: The brain of the system, where the operator controls everything from ventilation to temperature and conveyor speed. ⚙️ Lighting: LED-based lighting provides excellent visibility while also offering energy savings. 💡 Why Choose Our Painting & Drying Systems: Quality: Carefully designed with advanced features to ensure greater efficiency and performance. 🎯 Safety First: Efficient exhaust systems, fire suppression, and fire-resistant materials ensure a safe working environment. 🛡️ Customization: We offer customizable solutions that cater to your specific needs and preferences. 🛠️ Easy Maintenance: Our systems are designed to be easy to maintain, with durable and easy-to-clean materials. 🔧 Lredsun R Ufepfx Abyeu Excellent Support: We provide top-notch customer service and technical support for installation, troubleshooting, and optimal maintenance. 🧰 Environmental Responsibility: Our systems are designed to be energy-efficient and environmentally friendly, minimizing pollution and making them a sustainable choice for surface treatment. 🌍 Complete Solutions for Painting Systems: Conveyor Systems: Automated transport systems for painting and blasting booths, with intersections and switching systems for parts up to 2000 kg. 🚛 Easy-to-Replace Filters: Painting booths with ceiling exhausts and easy-to-replace filter elements. 🧹 Versatile Heating & Drying Solutions: Heating options include oil, gas, or electrical heating, as well as cross-flow heat exchangers and activated carbon filters for solvent-heavy processes. 🌡️ Integrated Paint Supply System: An integrated paint supply system with airless pumps for full coverage in the painting booth. 🎨 Our complete solutions provide everything you need for efficient and safe painting operations. Get in touch with our experts today to optimize your painting system!

Condition: new, SAPI Powder Coating The Perfect Coating for Lasting Protection. Powder coating is a highly effective and widely used method for applying a protective and decorative surface to various types of substrates. It is a dry finishing process where a fine powder made of resins, pigments, and additives is applied to a substrate. The powder is electrostatically charged, allowing it to adhere evenly to the surface and form a uniform coating. To achieve optimal adhesion and durability, the substrate is thoroughly cleaned and prepared first. Oils, dirt, and other contaminants are removed to ensure a clean surface. This is crucial for ensuring that the powder bonds effectively to the substrate, creating a strong and long-lasting coating. Components of a Powder Coating System A typical powder coating system consists of several components and devices required for applying and curing the powder coating. Spray Booth and Spray Area The booth provides a clean environment for the application process and ensures an even distribution of the powder. 🎨 Powder Coating Gun A powder coating gun is used to apply the powder coating to the workpiece. 💨 Powder Feed System The powder feed system consists of a hopper or container where the powder coating material is stored. It typically includes devices like powder pumps, feed hoses, and powder sieves to transport the powder from storage to the spray gun. 🔄 Pre-treatment Equipment Pre-treatment systems are used to prepare the substrate before applying the powder coating. This can include processes like cleaning, degreasing, rinsing, and surface treatment to ensure proper adhesion and durability of the coating. 🧼 Curing Oven A curing oven is a crucial component of a powder coating system. It is used to heat the coated substrate to the correct temperature so the powder coating melts, flows, and hardens into a permanent surface. The oven usually consists of a conveyor system or racks to transport the coated parts through the oven chamber. 🔥 Exhaust System An exhaust system is installed to remove excess powder, fumes, or volatile compounds generated during the coating process. It helps maintain a clean and safe work environment for the personnel and prevents the accumulation of powder particles in the air. 🌬️ Looking for a Powder Coating Solution? Are you searching for a custom powder coating solution? Ledpfjun Sd Usx Abyjru We specialize in providing tailored powder coating solutions to meet your individual needs. Whether you have specific color requirements, complex designs, or challenging substrates, our experienced team is ready to deliver exceptional results. 💡 Contact us today to discuss your requirements, and let us develop a custom powder coating solution for you. 📞 Get in touch with us today!

Condition: excellent (used), Year of construction: 2015, machine/vehicle number: 03814V2200, functionality: fully functional, operating hours: 2,416 h, input voltage: 380 V, type of input current: three-phase, travel distance X-axis: 2,200 mm, travel distance Y-axis: 1,200 mm, travel distance Z-axis: 280 mm, number of slots in tool magazine: 1, total height: 2,400 mm, total length: 3,000 mm, total width: 1,200 mm, overall weight: 1,100 kg, table length: 2,200 mm, table width: 280 mm, coolant supply: 3 bar, feed length X-axis: 2,200 mm, feed length Y-axis: 1,200 mm, feed length Z-axis: 280 mm, feed rate X-axis: 7 m/min, feed rate Y-axis: 7 m/min, feed rate Z-axis: 6 m/min, spindle motor power: 4,500 W, number of spindles: 1, rapid traverse Z-axis: 6 m/min, rapid traverse X-axis: 7 m/min, rapid traverse Y-axis: 7 m/min, rotational speed (max.): 18,000 rpm, rotational speed (min.): 1,000 rpm, spindle speed (max.): 18,000 rpm, spindle speed (min.): 1,000 rpm, table height: 1,200 mm, Equipment: rotational speed infinitely variable, NUMERICALLY CONTROLLED PANTOGRAPH WITH VERTICAL PLANE MODEL "VERTICAL 2200 OPEN" WITH 3 INTERPOLATED AXES FOR WORKING MARBLE AND GRANITE basic assembly: - range: x-axis=2200 mm. y-axis=1200 mm. z-axis=300 mm; - work surface L. 2500 x H. 1250 mm; - heavy carpentry-made structure in processed and painted steel; - Side openings with loops, both on the left and on the right, for processing oversized blocks with support rolls; - slabs and carter support in inox steel; - highly deep workbench made with extruded aluminium profile ; - slab locking with n°2 clamps with mechanical blocking device; - three-phase electro spindle hp 5 1/2 gas connection with perforated shaft and rotating joint for water passage for internal and external tool refrigeration, and inverter for variation to maximum 18000 r.p.m .; - openable polycarbonate protection for electro-mandrel, with safety micro; - axes movement by means of runners and sliding blocks of balls recircle; - dust tents for total protection of all moving parts; - water cooling tool system with centralized drain, including pump, decanting tanks and locking electrovalve; - electronic panel with console comprising numeric control, pc and monitor. Windows software included ARTCAM INSIGNA: - carrying out of reliefed and engraved writing, using all "true Type" fonts; - cad for carrying out drillings, cuts, engravings, millings and inlays; - import of most common types of files as dxf and dwg to create writings, drawings and stamps, reliefed and engraved logos, showr trays, sinks, arcs and portals; - automatic drilling for inserting bronze letters; - carrying out single and multiple sculptures in high and bas-relief; automatic switch off; 3D PLAN LASER laser copyng system to import manufactured products and tree-dimansional figures (bas and hight - relief) with interface and software for required dimensions Lsdpfxjygxc Ao Abyoru

Condition: as good as new (ex-display), functionality: fully functional, machine/vehicle number: 525389e4-9874-4408-810c-82126df2811f, Year of construction: 2020, operating hours: 7,508 h, overall weight: 75 kg, inner dimension height: 180 mm, inner dimension length: 300 mm, inner dimension width: 220 mm, Equipment: CE marking, Hardly used showroom complete system consisting of the following components: Markforged Metal X 3D printer Markforged Wash 1 debinding station Markforged Sinter 2 industrial sintering furnace & additional accessories Markforged Metal X TECHNICAL DETAILS Build volume: 300 x 220 x 180 mm Printing process: Atomic Diffusion Additive Manufacturing (ADAM) Print chamber: Heated Build plate: Heated, vacuum-sealed, with automatic leveling Printing system: Dual extruders – metal material and release material Print materials: Stainless steel 17-4 PH, 316L, tool steel H13, A2, D2, Inconel 625, copper, titanium-6Al-4V Media supply: Filament feed, bound powder material Part Features Maximum part size: 250 x 183 x 150 mm Layer thickness: 50 microns and 125 microns MACHINE DETAILS Dimensions & weight Dimensions: 575 x 467 x 1,120 mm Weight: 75 kg Software: Eiger Cloud Printer power supply: 100–240 V / 50–60 Hz / 12.6 A Lrjdpfx Asx I Rfgjbysu Certifications: CE, FCC, UL, RCM, UKCA Safety features: Two-factor authentication, organizational admin access, single sign-on EQUIPMENT Argon gas control with pressure reducers and quick couplings Original Markforged transport case with spare build plates Mobile castors Isolation transformer

Condition: new, Year of construction: 2026, functionality: fully functional, power: 198 kW (269.20 HP), Plastic squeeze dryers / Agglomerators are a vital part of plastic film washing lines. Lsdpswg Sgcofx Abyjru Washed films retain up to 40% moisture normally after exiting the wash process. High humidity will be affecting the efficiency and production of the following extrusion pelletizing process. Having a plastic squeeze dryer/Agglomerator is a must to dehydrate the washed film and increase the density of recycled film and fibre material. This also will increase the capacity of the extrusion process and further refine the quality of final plastic pellets. Even the water-washed plastic film processed through a spin-dryer still contains over 10% moisture which would be uneconomic to agglomerate on a conventional batch agglomerator. By redusing the moisture so significantly the productivity of the extruder and quality of pellets is increased exponentially. The latest development for drying and simultaneously agglomerating washed film are plastic film squeeze dryers which could reduce moisture to the minimum and the resultant squeezed material only contains maximum 3%, and more usually 1%, residual moisture. Much cheaper to operate than hot air drying where materials are still in lightweight flake form, and better result as the output materials are continuously agglomerated direct from washing lines with +40% fluids on entry to the dryer, to output dense free flowing agglomerate. In this form it is not necessary to have cutter compactor extruders saving more energy, as the materials are so dry and dense they can be fed direct to extruders for pellet production. With over 30 years of producing recycling dryers and extruders GENIUS have sold more than 600 of these driers to the plastics recycling market. ..There are 4 models in the range with production between 250 kgs per hour up to 1200 kgs per hour.

Condition: new, Year of construction: 2026, SEM65/28 PVC Corrugated Pipe Extrusion Line Complete Production Line for Flexible Corrugated PVC Pipes Ø10–40 mm The SEM65/28 extrusion line is designed for continuous production of flexible corrugated PVC pipes. The line includes automatic material feeding, drying, extrusion, water-cooled pipe forming, automatic cutting and double-station winding. Equipped with Siemens PLC control and DELTA frequency inverters. Only one operator is required. 1. General Specifications * Model: SEM65/28 * Material: PVC * Capacity: 40–70 kg/h, depending on material * Pipe Diameters: Ø10, 16, 20, 25, 32, 40 mm * Wall Thickness: 1–2 mm * Production Speed: 5–30 m/min * Total Installed Power: 50 kW * Actual Power Consumption: Approx. 70–80% * Power Supply: 380 V, 3-phase, 50 Hz * Operating Direction: Right to left * Operators: 1 * Color: Grey * Installation Space: 11 × 2.5 × 3 m * Operating Temperature: +5°C to +40°C * Maximum Humidity: 85% 2. Equipment Included 1. ZJ300 Vacuum Auto Loader – 1 unit 2. STG-U100 Hopper Dryer – 1 unit 3. SEM65/28 Single-Screw Extruder – 1 set 4. Extrusion Die Head with Interchangeable Tooling – 1 set 5. Corrugated Pipe Forming Mold Blocks – 3 sets Ø10-40, Ø25-20, Ø16-32 6. High-Speed Corrugator – 1 unit 7. Automatic Double-Station Winder – 1 unit Lodpfx Ajz Nkpwebysru 3. SEM65/28 Single-Screw Extruder * Screw Diameter: 65 mm * L/D Ratio: 28:1 * Screw Speed: 0–40 rpm * Main Motor: 22 kW, asynchronous * Motor Control: DELTA vector inverter * Screw & Barrel: 38CrMoAlA, nitrided * Heating Zones: 4 * Heating Power: 3.2 kW × 4 * Heaters: Ceramic * Cooling Fans: 4 × 0.18 kW * Feed Throat Cooling: Water * Gearbox: SJF-173 * Gearbox Lubrication: Forced * Gear Material: 20CrMnTi steel * Capacity: 40–70 kg/h * Control: PLC 4. High-Speed Corrugated Pipe Forming Machine Water-cooled corrugator with an enlarged cooling area for efficient pipe forming. * Main Drive: 4 kW induction motor * Speed Control: DELTA inverter * Forming Plate Hardness: 63.4 HRC * Cooling: Water * Vertical Adjustment: Electric * Horizontal Adjustment: Manual * Adjustment Motor: 1.1 kW * Platform Travel: 800 mm * Forming Method: Pneumatic blow forming * Vacuum Pump: 4 kW Automatic Cutting System * Pneumatic inline cutter * Adjustable cutting length * PLC control 5. Automatic Double-Station Winder * Type: Double-station * Drive: 12 N·m torque motor * Speed Control: Automatic synchronization * Traverse: Spindle speed tracking, frequency-controlled * Station Switching: Pneumatic self-locking * Air Pressure: 0.6–1 MPa 7. Wire device * Device for pulling a steel wire through corrugated PVC pipes during production, allowing easier cable installation 8. Applications Production of flexible PVC corrugated pipes for electrical cable protection, cable management, industrial installations and general-purpose conduit applications.

Condition: like new (used), Year of construction: 2020, functionality: fully functional, Rubber extrusion NBR&PVC Insulation sheet production line / available immediately The machine line can be delivered immediately, with few operating hours and in new condition. Production line units: 1. Zhejiang Baina 150 20D 1000Kg/h cold feed vacuum extruder (Standard) 2. Zhejiang Baina EJ-PPF-150-04-00 conical die (Pneumatic) 3. Zhejiang Baina 6m infrared curing oven (width 1000mm) 4. Zhejiang Baina 6m hot air curing oven (width 1140mm) 5. Zhejiang Baina 6m hot air curing oven (width 1440mm) 6. Zhejiang Baina 6m hot air curing oven (width 1600mm) 7. Zhejiang Baina 6m hot air curing oven (width 1800mm) 8. Zhejiang Baina 6m hot air curing oven (width 2000mm) 9. Zhejiang Baina 6m hot air curing oven (width 2300mm) 10. Zhejiang Baina 6m hot air curing oven (width 2500mm) Lsdpfx Aey Exrpsbyjru 11. Zhejiang Baina 6m hot air curing oven (width 2800mm) 12. Zhejiang Baina 36M FF-SLX-02-00 (3 layers * 12m) cooling system 13. PCM automatic longitudinal and transverse industrial cutting machine 2000mm 14. AC-15AD liquid chiller with 285 liters water tank If you are interested, we will send you a detailed description and data.

Condition: used, Year of construction: 2011, Water treatment plant from Grünbeck for treatment of brewing and process water. Fully mounted on a stainless steel frame and controllable via Simatic S7-300. Reverse osmosis system for removing hardness compounds, salts, particles and micro-contaminants from water. This produces brewing water with the desired hardness. To protect the membranes, coarser particles are first removed in two fine filters (with pore sizes of 50 µm and 5 µm respectively). Desalination then takes place in two pressure pipes containing membrane modules. Includes sterilization filtration, membrane modules, chemical dosing, centrifugal pump, piping, valves, measurement technology, and control cabinet with touch panel. Additional title: reverse osmosis Permeate capacity: 8000 l/h ; Feed: 10000 l/h Recovery: 80 % Concentrate: 2000 l/h Max. overpressure: 16 bar Power: 6.5 kW Voltage: 3 x 380 - 415 V Frequency: 50 Hz Water: feed 2.5 - 5 bar Length: 5000 mm Lodpfoz E Rv Uex Abyjru Width: 1000 mm Height: 2000 mm Operation / Control: Simatic S7-300 Material: membranes from polyamid Base construction: on stainless steel frame with feet Features: 2 fine filters; pressure pipes with membrane modules; chemical dosing system with two dosing pumps; centrifugal pump (Lowara); various pipes, valves, and measurement equipment; control cabinet with touch panel

Condition: ready for operation (used), functionality: fully functional, WALTHER CN 550 PN TROWAL & RÖSLER Z 300 Turbo Floc Centrifuge -Walther Trowal & Rösler Turbo Floc Centrifuge Ledpfoz Dg Ikjx Abyeru -Coating in good condition -Rotational speed: 1460 RPM -Capacity: 550 liters -Motor: 3.5 KW -Pneumatic soundproof cover -Control cabinet -SEPARATION UNIT -Dirty water / drain system -Compound and 2 x sets of sliding stones -Documentation Dimensions: L x W x H 2 x 1.8 x 1.8 meters / Weight: 1500 kg RÖSLER Z 300 TURBO FLOC - CENTRIFUGE -Year of manufacture: 1996 -Rotor speed: 3160 RPM -Power: 4 KW -Max. throughput: 800 liters / hour -Documentation -Dimensions: L x W x H 1.7 x 1 x 1.6 meters / Weight: 480 kg Errors and omissions excepted.

Condition: ready for operation (used), Year of construction: 2023, spindle motor power: 70,000 W, spindle speed (max.): 14,000 rpm, travel distance X-axis: 450 mm, overall weight: 32,000 kg, controller manufacturer: SIEMENS, controller model: 840D solution line, number of axes: 5, This 5-axis Weingartner Pick Up 400 machining center for screw manufacturing was manufactured in 2023. It features a maximum workpiece length of 4,000 mm and a maximum workpiece diameter for milling of 180 mm. The machine is equipped with a Siemens 840D control system and offers advanced simultaneous machining capabilities. If you are looking to get high-quality screw manufacturing capabilities, consider the Weingartner Pick Up 400 machine we have for sale. Contact us for further details. • Control: Siemens 840D solution line (NCU 720.3), OP19 touchscreen + Siemens TP700 touch panel • Simultaneous machining: 5-axis; B‑axis turning • Workpiece capacity: max length between centers 4,000 mm; max diameter for milling 180 mm; chuck size Ø260 mm • Power supply: 3 × 400 V / 50 Hz; main fuse approx. 200 AAxes • X: travel 450 mm; rapid 20 m/min • Y: travel −80 / +150 mm; rapid 20 m/min • Z: rapid 25 m/min • B: swivel range ±45°; max swivel speed 90°/s; clamping torque 5,000 Nm • C: max speed 50 rpm; max torque 1,740 Nm (cont.) / 2,580 Nm (40% duty) • W (tailstock slide): rapid 15 m/min • VZ1 / VZ2 (steady rest slides): rapid 15 m/minTurning / Milling Unit • Unit: UFE-400; tool spindle: MDFK • Power: 45 kW (continuous) / 70 kW (40% duty) • Max spindle speed: 14,000 rpm; nominal speed: 1,560 rpm • Torque: 275 Nm (continuous) / 430 Nm (40% duty) • Tool interface: HSK 100‑T (compatible HSK 100‑A / HSK 100‑T); additional interface: Capto C8 • Internal coolant: 80 bar; 20 l/minTailstock • Hydraulically operated quill; diameter 190 mm; stroke 200 mm; Morse taper MK6Machine equipment / configuration • Front and rear self-centering steady rests; independently CNC-positionable • 2 prismatic steadies for screw milling • Steady jaw ranges: 15–30 / 30–65 / 65–140 / 140–200 mm • Hydraulic SMW KNCS‑N 260 power chuck with quick jaw change • Central lubrication system • Fully enclosed machine housing with driven safety doors; Visiport inspection windows • Hydraulic and pneumatic systems • Coolant and oil mist extraction preparation • Electronic hand control for B/C/X/Y/Z axesSoftware / control functions • Siemens Safety Integrated; Profibus / Profinet; OPC UA interface • 5‑axis simultaneous machining; B‑axis turning; TRANSMIT / TRACYL • Temperature compensation X/Y • DNC remote diagnostics; WMDS Diagnostic System; Telediagnosis capability • weinCAD EXTRUDER DESIGNER; WeinEXT – Praxis Additional equipment Lredpjz D Efhofx Abyeu • Hinge-belt chip conveyor • Coolant filtration system KF 200: 1,400 l tank; 40 µm filtration; high‑pressure pump 80 bar / 46 l/min; low‑pressure pump 13 bar / 160 l/min; automatic oil skimmer • Oil mist extraction unit: airflow approx. 4,000 m³/h • Operating platform with stairs and railing