Used Cnc Drillng for sale (8,482)

Condition: excellent (used), Year of construction: 2015, Roll pressure infinitely adjustable from 240 kN feeds - fine adjustment 0,5-45 mm/min turning speeds 0-80 U/min Swivel angle of the roller heads 11 ° Diameter of the roller spindles 69,85 mm Stroke - Roller screw slide 0-150 mm min. dist. - roller screws 138 mm max. dist. - roller screws 285 mm min. diameter - Rolling tools 230 mm max. diameter - Rolling tools 135 mm min. dia. 2 mm max. diameter 55 mm thread length at plunge operation 200 mm Kedpsxukrqjfx Ag Uedg thread length at continiuous operation 2000 mm maximum thread pitch 4 mm total power requirement 14 kW weight of the machine ca. 2,4 t dimensions of the machine ca. 2,0 x 2,5 x 1,9 m Rolling time continuously adjustable from: 0.1s Pause time continuously adjustable from: 0.1s Rolling spindle length: 200mm Machine bed height: 810mm Rolling spindle height above machine bed: 200 mm Height of support bearings: 115 mm Largest pitch for serrated teeth: 2.5 mm (up to 70 kg/mm2 Strength of the material)

Condition: ready for operation (used), Vermogen slijpsteen: 15 kWt Besturing: Siemens Sinumerik 840 C Siemens drive: 6SN1145-1BA00-OCAO Worklength with magnetic table: 1270 mm Grindingwidth: 610 mm Longitudinal travel X-axis (autom.): 1310 mm Cross-travel Y-axis (autom.): 565 mm Travel Z-axis (autom.): 470 mm Dimensions of the table: 1215 x 500 mm Distance between table -- spindlecentre: 680 mm Max dia grindingstone: 400 x 100 x 127 mm Spindlespeeds: rpm Motorpower: 30 / 47 kWt Tension needed: 380V - 50Hz Cooling system: yes Kjdjxl Hxhjpfx Ag Ujdg

Condition: excellent (used), Year of construction: 2013, functionality: fully functional, machine/vehicle number: 40898, SPECIFICATION Table size 1270 x 320mm Longitudinal traverse (X axis) 750mm Cross traverse (Y axis) 400mm Vertical traverse (Z axis) 500mm Maximum table load 500Kg Quill travel 127mm Quill feeds 0.04, 0.08, 015mm/rev Quill diameter 100mm Quill taper ISO40 Spindle motor 5.6kW Kdsdpfxsx S Nfgo Ag Ueg Spindle speeds (inf. variable) 50 – 3800rpm Spindle nose to table 100 – 600mm Spindle centre line to column 500mm Head tilt left or right 0 – 90 degrees Approximate weight 2500Kg Machine in Metric execution   MACHINE EQUIPPED WITH Heidenhain TNC 320 CNC Control Air power drawbar Power rise and fall to knee Interlocked table guard Base splash tray Coolant system Automatic Lubrication system Lighting Vice

Year of construction: 2023, condition: as good as new (ex-display), functionality: fully functional, XX100329 FMC 120 - CNC machining centre Kdedpfx Agsya H Aqj Ujg 1x PR204832 Vice conversion with pneumatic block 1x PR204851 5-position automatic tool magazine (ISO 30) 1x PR-27602 TOOL SET ALUMINIUM TYPE 1 1x ZP714617 Custom 2D milling module FST CAM 4 1x PR-28965 Rotation of the work table to intermediate angles with manual stop

Condition: as good as new (ex-display), Year of construction: 2024, functionality: fully functional, The most easy dovetail machine in the world – see the difference iDovetail designed to solve your staff training time and the correction time when changing the workpiece. Anyone can operate this machine. It is as easy as a mobile phone or a printer. We use the real-time model to replace the existing field input on the market, let you enter the size directly on the model, you can master your finished product 100% in the design stage Working width (mm) : 50-610 Working thickness(mm) : 5-50 Minimum length (mm) : 170 Total Power (kw) : 4.2 Kdodsx Upzmepfx Ag Ujg Spindle Power (kw) : 3 Spindle Speed (RPM) : 24000 Net Weight (kg) : 750 Shipping Weight (kg) : 800 Overall Size (W x H x L) (cm) : 121 x 120 x 109

Condition: excellent (used), Year of construction: 2020, Swing over bed 880mm, Swing over saddle 817 mm, Maximum turning diameter 550mm, maximum turning length 3070mm, bar capacity 116.5mm, Y axis +/- 75mm, Kdsdpex I N Rbjfx Ag Usg Spindle speed 2000rpm, milling speed 4,000rpm, spindle power 37/30KW, 12 station turret, Fanuc IPlus control. 3 jaw chuck, tool setter, Hydraulic steady, swarf conveyor,

Condition: used, Year of construction: 1999, x-travel 2000 mm y-travel 800 mm z-travel 850 mm control HEIDENHAIN TNC 360 total power requirement / kW Kjdpjv H Ertsfx Ag Ujdg weight of the machine ca. / t required space / m

Condition: used, Year of construction: 2007, turning length 1500 mm control FAGOR 8055i/A TC centre height 230 mm Ksdpfxjv Hhv Us Ag Uodg greates pass round over bed 475 mm swing diameter over slide rest 240 mm bed width 355 mm max. workpiece weight 1500 kg spindle bore 65 mm spindle turning speed range 100-4500 U/min weight of the machine ca. 3,15 t required space 3,51 x 1,80 x 2,02 m

Condition: used, Punch Tonnage Capacity: 75 to 80 tons Shear Tonnage Capacity: Up to 250 tons, Maximum Angle Size: 6 inches x 6 inches x 1/2 inch (or 152 mm x 152 mm x 16 mm) Minimum Angle Size: 1.5 inches x 1.5 inches x 1/8 inch (or 38 mm x 38 mm x 3 mm) Max Flat Bar (Shear & Punch): 6 inches x 1/2 inch (or 152 mm x 16 mm) Max Hole Size: 1-1/4 inches (32 mm) Kdjdpfxex Ruvuj Ag Ueg

Condition: good (used), functionality: fully functional, Year of construction: 2004, General Specifications Kdedpfex Ruvnox Ag Ujg Maximum Plate Thickness: Up to 32 mm. Maximum Plate Width: 1828.8 mm (72 inches). Minimum Plate Width: 152 mm (6 inches). Punching Capabilities Punch Capacity (Tonnage): 160 to 177 metric tons. Maximum Punch Hole Size: Up to 45 mm (1.75 inches) in diameter. Maximum Material Thickness for Punching: 32 mm (1.25 inches). Additional Features Hypertherm HT2000

Condition: good (used), functionality: fully functional, Year of construction: 2010, PEDDINGHAUS FDB1500/ 3C. YEAR OF MANUFACTURE 2010. 1500mm CAPACITY X 6000mm. PLASMA / OXY FUEL / DRILLING. Kdedpfxjx Ruu De Ag Ujg HYPERTHERM HPR 260 SOURCE. Peddinghaus FDB 1500 plate processing machine for drilling and flame cutting. CNC control Siemens Sinumerik 810 Machining dimensions: machining width from 80 to 1500 mm, sheet thickness from 6 - 50 mm, material length as a base up to 6000 mm, (the length is very easy to extend because of the roller measuring system). Drill diameter: min. ø 8, up to max. ø 40 mm suitable for HSS coolant channel drill (cooling by the drill spindle),

Condition: good (used), functionality: fully functional, Year of construction: 2008, Peddinghaus BDL 1250/9D Meba 1270 DGP CNC Drilling / Sawing Line - Year 2008. 9 spindles. Etching of beam. Carbide Drilling Kdsdpfsx Ruuwex Ag Uog Hard stamping unit. Measuring Head. In-Feed Cross Transfers. Out-Feed Cross Transfers. 1250mm Capacity.

Condition: excellent (used), Year of construction: 2012, Vernet Behringer HD-X 918 / HBP 410/923 CNC Sawing / Drilling Line – Year 2012. Split system. 3 Spindle. Kdedpfxex Ruude Ag Usg Automatic tool changer. 24 metres infeed. 18 metres outfeed. Gripper Feed measuring system. Infeed and outfeed Cross Transfers.

Condition: excellent (used), Year of construction: 2013, Vernet HD-X 618 / HBP 410/723 G CNC Drilling / Sawing Line – Year 2013. 3 Spindle Drill. 16.5 metres In-Feed. 14 metres Out-Feed. Pusher Unit Feed. Kdedpfx Agex Rut Te Ujg Milling / Slotting. Solid Carbide Tooling. Small parts conveyor. 4 way Scribing. In-Feed Cross Transfers. Out-Feed Cross Transfers.

Condition: excellent (used), Year of construction: 1997, functionality: fully functional, machine/vehicle number: 1114.3705-24, Used CNC Lathe Make: Boehringer Type: VDF 250Cm Year of Manufacture: 1997 VDF Boehringer 250C The machine has the following features: 1000mm turning length No tailstock Driven tools Special indexing chuck Siemens 840C control system Kjdpfxowlap Ae Ag Uedg The Boehringer VDF 250Cm is a CNC lathe designed for machining chucked parts. It is characterized by its robust construction and precise machining capabilities. Technical Specifications (Model Year 1997) Working Area: Swing over Bed: 550 mm Swing over Cross Slide: 480 mm X-Axis Travel: 405 mm Z-Axis Travel: 1,099 mm Maximum Turning Length: 1,000 mm (None) Tailstock: Tool Turret: Number of Positions: 12 Tool Holder: VDI 50 DIN 69880 Live Tools: YES Spindle: Spindle Head Size: 8 DIN 55026 Spindle Bore: 103 mm Max. Chuck Diameter: 315 mm Max. Drive Power (50% Duty Cycle): 53 kW Max. Torque: 780 Nm Speed Range: 30–3,000 rpm Feeds: Automatic Feeds: 1–10,000 mm/min Rapid traverse speed: 10 m/min (X and Z axes) Max. feed force: 15 kN Dimensions and weight: Machine dimensions (L × W × H): approx. 5,400 × 3,200 × 2,400 mm Machine weight: approx. 11,000 kg Equipment: Pivoting control panel Hydraulic system from HYDROKRAFT Coolant system with 600 l tank, max. pump pressure 5.5 bar, flow rate 60 l/min, pump power 1.1 kW Chip conveyor with 325 l tank capacity, right-hand discharge 3-jaw power chuck Oil mist extraction Control cabinet with cooling unit and temperature controller from RITTAL Control system: SIEMENS SINUMERIK 840 C Variants and Differences There are various variants of the VDF 250 series, such as the VDF 250 CU, which can be equipped with different control systems (e.g., PHILIPS B2T) and technical specifications. Some models feature driven tools and a tailstock, while others are designed as pure chuck-type lathes without a tailstock. Conclusion The Boehringer VDF 250 Cm is a versatile CNC lathe characterized by its stability and precision. With its robust construction and extensive features, it is ideally suited for machining chucked parts in a variety of production environments.

Condition: good (used), Year of construction: 2007, operating hours: 88,040 h, functionality: fully functional, machine/vehicle number: 07400003691, turning diameter: 120 mm, spindle bore: 118 mm, rapid traverse X-axis: 30 m/min, rapid traverse Y-axis: 15 m/min, rapid traverse Z-axis: 30 m/min, total height: 2,500 mm, total length: 5,500 mm, total width: 2,500 mm, overall weight: 11,000 kg, controller manufacturer: SIEMENS, controller model: SINUMERIK 840 D POWERLINE, DMG GILDEMEISTER TWIN 102 CNC Turning and Milling Center - Recorded spindle hours: 43,558 - Spindle speed range: 3,200/5,000 rpm - Swing diameter: 270 mm - Spindle distance: 900 mm - X1 axis travel: 290 mm - Z1 axis travel: 650 mm - X2 axis travel: 180 mm - Z2 axis travel: 650 mm - Y1 axis travel: ±40 mm - Z3 axis travel: 670 mm - X3 axis travel: 175 mm - Max. bar diameter: 100/104 mm - Number of driven tools per tool turret: 12 - Including chip conveyor, with 2 tool turrets (each with 12 tool stations), main and counter spindles, as well as foot switches Attention, the machine has the following defects: - The B-axis is defective (mounted on turret 1) - Guideways and drives show age-related wear - X2 axis (guide rails) runs slightly out of alignment by approximately 0.03 mm (should be re-measured) - Occasionally, axis reference value setting in the control system fails - The hydraulic pump was replaced after a failure and is now installed externally as a standalone unit FCA D-58256 Ennepetal, loaded on truck at a mutually agreed date at the end of February 2026. Kjdpfxoyaqgyj Ag Uedg

Condition: good (used), Year of construction: 2008, operating hours: 72,899 h, functionality: fully functional, machine/vehicle number: 07510001241, turning length: 1,185 mm, turning diameter: 640 mm, spindle speed (max.): 12,000 rpm, workpiece weight (max.): 150 kg, total height: 3,040 mm, total length: 7,800 mm, total width: 4,100 mm, overall weight: 16,500 kg, controller manufacturer: SIEMENS, controller model: SINUMERIK 840 D, DMG GILDEMEISTER GMX 250 LINEAR CNC Turning and Milling Center - Recorded spindle hours: 39,361 - Swing diameter: 640 mm - Counter spindle turning diameter: 400 mm - Spindle distance: 1,500 mm - X1 axis travel: 550 mm - Y1 axis travel: 180 mm - Z1 axis travel: 1,185 mm - B1 axis travel: 240° - X2 axis travel: 180 mm - Z2 axis travel: 1,050 mm - Z3 axis travel: 1,150 mm - Spindle speed range: 3,200/4,000 rpm - Rapid traverse rate, Slide 1 (X/Y/Z): 40/24/70 m/min - Rapid traverse rate, Slide 2 (X/Z): 24/36 m/min - Rapid traverse rate, Slide 3 (Z): 36 m/min - Tool holder: HSK 63 - Spindle speed: 12,000 rpm - Number of tool stations in chain magazine: 40 stations - Incl. tool holders mounted on the turret - Incl. bar loader, manufacturer: COCCHE GIOVANNI, type: CNC-DB 110, year of manufacture: 2008, serial number: CNCDB-08.306, weight: 1,500 kg Note: The machine has the following defects: Kjdpjyaqczsfx Ag Usdg - The hydraulic unit is faulty – it needs to be repaired - The Q2 axis (milling spindle tool changer) fails frequently - X2 axis (guideways) moves slightly askew - The linear guides and drives show wear commensurate with age Attention: A vehicle with 3,000 mm transport width is required for transport! FCA D-58256 Ennepetal, loaded onto truck at a mutually agreed date at the end of February 2026.

Condition: used, Year of construction: 2022, Price: On request What are Presale Items at Second Owner? Kdjdpfxjx Tt Uns Ag Ueg Presale items are machines that we sell in their current condition ("as-is"). We have purchased these machines based solely on photos and sell them with the information provided in the advertisement. Unfortunately, we do not have additional details, such as exact dimensions or machine specifications. Additionally, these machines are often not yet in stock and have not been inspected by us. These machines are offered at competitive prices, which means the prices are lower than usual, but the risk lies entirely with the buyer. Please carefully review the information in the advertisement before making a purchase. If you have any questions, feel free to contact us! - Year: 2022 - Documentation available: Yes - CE marking present: Yes - CE certificate present: No - Serial number: 30B.11.040.22 - Type milling table: Beam table - Tool clamping system: HSK-F63 - Drilling unit present: Yes - └ Horizontal drill spindles [pcs.]: 4 - └ Vertical drilling spindles [pcs.]: 12 - Saw unit present: Yes - Working range X [mm]: 3300 - Working range Y [mm]: 1280 - Z-axis working range [mm]: 250 - X-axis maximum stroke [mm]: 4000 - Y-axis maximum stroke [mm]: 1670 - Z-axis maximum stroke [mm]: 500 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets

Condition: used, Year of construction: 2018, - Year: 2018 - Documentation available: Yes - CE marking present: Yes - CE certificate present: No - Number of milling spindles [pcs.]: 1 - └ Milling spindle 1: - - Number of controlled axes [pcs.]: 5 - Type milling table: Beam table - Drilling unit present: Yes - Tool changer positions [pcs.]: 1 Kjdpfjxtbgpox Ag Ujdg Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets

Condition: excellent (used), Year of construction: 2004, turning length / mm turning diameter over bed / mm turning diameter over slide / mm control / Universal lathe VDF Boehringer DUS 1000 ti OPTIONAL EQUIPMENT SURCHARGE: C-AXIS MILLING TOOL Machine no. 2042.6616-05 Year of construction 2004 Turning length approx. 2200 mm Swing diameter over bed 1,000 mm Swing diameter over bed 1,000 mm Centre height over flat track 500 mm Bed width 560 mm Bed slide guide length 800 mm Spindle diameter front bearing 170 mm Spindle bore 128 mm Infinitely variable three-phase motor (AC motor) Drive power 37 kW Torque max. 4,069 Nm Total speed range 6.4 - 1,600 Gear stages 2 Heidenhain control Manualplus 4110, completely renewed approx. 1 to 2 years ago renewed 2 lynchets Equipped with roto power chuck, diameter approx. 500 mm. Including many accessories of clamping jaws, estimated 15 sets, as well as approx. 15 sets of Multifix basic holders, size D. Machine was equipped with a separate milling device, with its own control, value approx. 20.000,00 €. Ksdpfx Asud In Hog Ujdg OPTIONAL EQUIPMENT SURCHARGE: C-AXIS MILLING TOOL Only operated by the owner, very good condition!

Condition: used, Year of construction: 2001, turning diameter / mm turning length / mm control / total power requirement / kW weight of the machine ca. / t Kdedjx Tu Sujpfx Ag Uog required space / m

Condition: used, Year of construction: 2006, Solid drill diameter / mm bore depth / mm number of spindles / Froriep CNC deep hole drilling machine – the prefabrication specialist Year of manufacture: 2006 Control system: Siemens Sinumerik 840D Max. drilling depth: 8,850 mm Workpiece diameter: 150 – 900 mm Speed range: 1 – 300 rpm Kdedpfxjxgu R Io Ag Uog Feed rate: 0.5 – 4,500 mm/min Drive power: 129 kW Swing diameter over bed: 1,000 mm Clamping diameter faceplate: 900 mm Weight: approx. 47,000 kg Ideal for precise pre-drilling of deep holes – including faceplate, steering ring

Condition: used, Year of construction: 1980, turning diameter 7000 mm faceplate diameter 3500 mm workpiece height 3000 mm 160 mm 1998 Control Siemens 840 C max. table load 60000 kg electr. connected load 400 V Serial number 11 33 0051 total power requirement 71 kW weight of the machine ca. / t required space 13 x 6 m The SCHIESS-FRORIEP 40 DV is a vertical lathe built in 1980. The machine was modernized and improved in 1998. Among other things, a driven tool system (C-axis) was installed. In addition, the control system was modernized to SIEMENS 840 C. The large open-sided vertical boring mills with travelling column - type DV - are particularly suited to situations where likely workpieces frequently change in diameter but where maximum workpiece dimensions are rare. Decisions in favour of this type of machine are generally due to minimum floor space requirement, universal adaptability and economical advantages. The modern design of these machines is characterized by rigid all-steel construction optimized by computer - SCHIESS can claim to have done much valuable pioneering work in this area of heavy-duty machine tool building. Ksdpfx Agjuddlzj Usdg

Condition: excellent (used), Year of construction: 1989, turning length / mm turning diameter over bed / mm turning diameter over slide / mm control / WOHLENBERG PT1-1070II Heavy-duty lathe Very good condition heavy duty lathe, make Wohlenberg. The machine was partially overhauled in 2013! Type PT1-1070II Year of manufacture 1989 partially overhauled in 2013 Country of origin Germany CNC control Siemens 840 D extended from 7 m to 11 m turning length Santer turret geometry Turning diameter over bed 1,070 mm Turning diameter over support 710 mm Turning length 11,000 mm Bed width 710 mm 2 gear stages Speed 3.55 - 710 rpm Quill diameter 200 mm Quill stroke 350 mm Spindle clearance 128 mm Chip conveyor Kodpsud Ipkofx Ag Usdg Boring tower incl. boring bar Length approx. Ø 200 x 2,430 mm Face plate 1,000 mm Steady rest 4 quills 500 mm open Main drive motor 71 kW incl. documentation

Condition: used, diameter 315 mm Kodspp Dwdepfx Ag Usdg Control / weight of the machine ca. / kg