Used C Frame for sale (58,488)

Condition: used, Pneumatic press, compressed air press BOSCH Type Manufacturer’s No. Year of manufacture 1980 Pressing force: 18 kN = 1.8 tons at 5 bar 15 kN = 1.5 tons at 4 bar 12 kN = 1.2 tons at 3 bar 8 kN = 0.8 tons at 2 bar 6 kN = 0.6 tons at 1.8 bar Overhang: 100 mm Ram stroke: 70 mm Table surface: 245 x 200 Ram surface: Ø 45 mm Maximum installation height: 235 mm Dsdpfx Aoh U Dtuja Iswc Arbor hole: Ø 20 mm with clamping screw Compressed air requirement: 5 bar - Pressing force can be continuously adjusted via a pressure regulator - Pneumatic cylinder with ram, height adjustable by 90 mm - Pneumatic two-hand operation - Mounted on a metal frame with wooden plates Space requirement L x W x H: 1050 x 700 x 1600 mm Weight of pneumatic press: 82 kg Weight with table frame: 140 kg In good condition

Condition: new, pressure: 125Tappet adjustment: (automatische Verstellung) 40stroke lenght (max.): 10-125total power requirements: 11weight approx.: 8000messurements (LxWxH): 1800 x 1500 x 2600 Dsdpfxjktm N Ds Aa Ijwc

Condition: used, Single-column eccentric press KRUPP, type PEKRD 125 h Machine No. 2861, Year of manufacture 1977 Pressing force: 125 tons Reach: 400 mm Table size: 950 x 750 mm Ram area: 800 x 540 mm Table opening: 100 x 250 mm Stroke adjustment: 8 to 160 mm Ram adjustment: 100 mm Installation height for maximum stroke at the top: max. 550 mm Stroke rate: 60 strokes/min. Table height above floor: 800 mm Motor power: 10 kW Power connection: 380 volts, 50 Hz - Hydraulic overload protection in the ram - Pneumatic clutch and brake combination ORTLINGHAUS - Ram weight compensation cylinder - Motorized ram adjustment - Tabletop with ball bearings - Two-hand operation - Central lubrication system HELIOS - Stroke counter - UVV 7n 5.1 §4a, paragraph 2, No. 3b for manual feeding operations Space requirement L x W x H: 2300 x 1800 x 3200 mm Dedpfjdzqddjx Aa Iewc Weight: approx. 10 tons Good condition (very little use)

Condition: new, pressure: 150Tappet adjustment: (automatische Verstellung) 40stroke lenght (max.): 10-125total power requirements: 15weight approx.: 9500messurements (LxWxH): 1800 x 1500 x 2600Stroke/min: 50-90 Machine Technical SpecificationsCE Compliance: The machine and all equipment are manufactured in accordance with CE regulations Light Curtains: SICK or PILZ PLC Control: Siemens S7-1200 Stroke Adjustment: Directly via the touchscreen interface Balancing System: Integrated Djdpfx Aaotqwtdj Iswc Stroke Speed Adjustment: Via Mitsubishi frequency inverter Machine Frame: Full steel construction Guidance System: Inner and outer eccentric guides Crankshaft: Made of hardened 4140 steel Clutch & Brake: Pneumatic combination system Safety Valve: Dual-way safety valve Safety PLC: SICK or PILZ Operation Modes: Two-hand operation and foot pedal available Lubrication: Automatic centralized lubrication system Overload Protection: Hydraulic overload system Safety Guarding: Protective enclosure around the working area External I/O: 8-pin I/O ports on PLC (for external connections and signal exchange) Anti-Vibration: Rubber dampers under the machine feet (1 pair – 4 pieces) Power Supply: 400 V / 50 Hz Required Fuse: 32 A Control Panel: 19 Siemens touchscreen ? Main Technical DataOperation Modes: Inch / Single stroke / Continuous stroke Press Force: 150 tons Table Dimensions: 750 × 1000 mm (fixed table) Stroke Length: 10–125 mm (automatically adjustable via PLC) Ram Dimensions: 500 × 800 mm (Ø55mm pin receptacle & T-slots customized to customer needs) Stroke Rate: 50–90 strokes per minute Main Motor: 15kW (1,400 rpm) Throat Depth: 325 mm Shut Height: 475 mm (adjustable down to 295 mm) Ram Bore Diameter: 50 mm Machine Dimensions:Length: 1,800 mm Width: 1,500 mm Height: 2,600 mm Machine Weight: approx. 9,500 kg Ram Adjustment: 40 mm (automatic adjustment)

Condition: ready for operation (used), Year of construction: 2015, operating hours: 8,995 h, functionality: fully functional, travel distance X-axis: 850 mm, travel distance Y-axis: 700 mm, travel distance Z-axis: 500 mm, feed rate X-axis: 35 m/min, feed rate Y-axis: 35 m/min, feed rate Z-axis: 35 m/min, controller manufacturer: Heidenhain, controller model: iTNC530 (HSCI), workpiece weight (max.): 600 kg, total height: 3,000 mm, total length: 4,500 mm, total width: 4,500 mm, table width: 65 mm, table length: 650 mm, table load: 600 kg, rotary table diameter: 650 mm, overall weight: 10,000 kg, spindle speed (max.): 15,000 rpm, operating hours of spindle: 8,995 h, coolant supply: 40 bar, spindle motor power: 15,000 W, spindle nose: HSK-A63, number of spindles: 1, number of slots in tool magazine: 38, input voltage: 400 V, Equipment: chip conveyor, documentation/manual, The HERMLE C 400 U is a high-quality 5-axis CNC machining center, designed for precise and efficient machining. With a working area of 850 × 700 × 500 mm and a Ø650 mm swiveling/rotating table, this machine offers ample space for both complex and larger workpieces. The machine is installed and operational at our facility and can therefore be inspected while running! Additional options & accessories: Dwjdpfx Ajz Nluuea Ijc - Chip conveyor - 40 bar internal cooling (IKZ) - Band filter system incl. 2 new rolls of filter paper. - BLUM LaserControl NT measuring system for tools. - Heidenhain TS 460 3D probe - Electronic handwheel - Tool cabinet incl. approx. 100 pcs. HSK-A63 tool holders, collets and accessories. - 2 pcs. All-Matic machine clamp - Heidenhain reference pin - Manual cabinet roof - Original HERMLE + Heidenhain documentation. Weight & dimensions: approx. 10,000 kg approx. 4.5 x 4.5 x 3 m

Condition: used, Year of construction: 2011, AXES Working area X-Y-Z axes * mm 3050-1300-180 Workpiece length in swivel machining mm 1390 Stroke X-Y-Z axes mm 3460-1735-250 Dwjdpfoyymz Ujx Aa Ioc Max. travel speed of the X-Y axes m/min 60 WORKING TABLE Number of workpiece supports and vacuum cups 6 / 2 Standard type Standard End stops / Position 1 / rear Vacuum pump m3/h 90/108 DRILLING UNIT Vertical spindles Std/Number/Speed 1/min 12 (8X-5Y) / 4000 Horizontal spindles Std/Number/Speed 1/min 6 (4X-2Y) / 4000 Integrated slotting/sawing unit in X Ømm/1/min 120 / 6000 Motor power kW (HP) 2.2(3) ELECTROSPINDLE Motor power Std. / Opt. (S6) kW (HP) 7.5(10) / 11(15) Max. speed 1/min 24000 Tool changer mounted on the unit carrier in X 4 positions, pneumatic INSTALLATION Installed power KVA 23÷28.5 Compressed air requirement Nl/min 450 Extraction air requirement m3/h 1900+1900 (3400) Required extraction air velocity m/sec 30 Extraction nozzle diameter mm 150+150 (200) Machine weight Kg 3000 * X Distance between the stops - Y Milling center as reference point; Z Workpiece passage GENERAL FEATURES CNC-controlled boring and milling center, in C-frame design and working table with adjustable workpiece supports and vacuum cups, for performing: - Vertical drilling on the surface of the panel - Horizontal drilling on all four sides of the workpiece - Slot milling with disc cutter in "X" direction - General milling operations Self-supporting structure and working table Structure made of a steel welded construction with the control cabinet integrated into the machine frame. Available in two different lengths and with standard workpiece supports or TV supports. Movable unit carrier Box construction made of cold-rolled steel with internal reinforcing ribs, protective devices with bumpers. Working unit Consisting of a drilling head with vertical spindles, horizontal spindles, an integrated slotting and sawing unit and an SCM electrospindle with tool quick-change system type HSK 63 F. Travel paths of the portal and the unit carrier Movement in the X, Y and Z axis takes place on linear prismatic ball-bearing guides with the aid of pre-tensioned linear guides. The power transmission of the X-axis (movable stand) takes place via a pre-tensioned, backlash-free rack and pinion drive with diagonal movement. The movement of the unit carrier in Y and Z direction takes place via pre-tensioned linear guides. The positioning of the working units and the control of the machine functions takes place via "Brushless" three-phase servomotors and digital drives. CNC CONTROL The control unit consists of a numerical control for the milling and drilling machines and a pre-connected personal computer with a graphical user interface "XILOG PLUS". PC -Office- operating system Windows XP - LCD color screen 17 - Qwerty keyboard - Swiveling control panel - Machine interface software Xilog Plus Xilog Plus features Programming - parametric, graphical and ISO programming - Import of DXF and ASCII files - Linear or circular interpolation in three axes, linear in space, spiral in the chosen plane - Supported programming with graphic and syntax aids for drilling and milling operations - Automatic optimization of drilling operations and tool changes - cycles - Possibility of plate zero-point shift for performing drilling on inclined or curved plate sides - Complete compatibility with CAD/CAM Routocam (SCM) - AlphaCam Integrated additional functions - Calculator for direct transfer of the calculated data.

Condition: excellent (used), Tucker Nimak MF180: Robotic welding tongs for single-sided resistance spot welding The robotic welding tongs for single-sided resistance spot welding from NIMAK utilize state-of-the-art medium-frequency transformers, a control system with adaptive welding current regulation, and finely adjustable welding cylinders for gentle power. Here, the right amount of force is crucial to reliably join materials without deforming them or leaving marks on the visible side. Our systems master this task perfectly. Tucker Stanley Punch Riveting Tool, C-Frame With the Tucker® SPR equipment, you can join materials that cannot be easily welded, including aluminum-aluminum, aluminum-steel, and high-strength steel, by combining two technologies in a modular system: Djdpfxezgcm Rs Aa Iowc punch riveting with semi-hollow rivets and solid punch rivets. AEG SVS Welding Technology Electrode Grinding Device EF310-01E-S-D-Fix Grinding of spot welding electrodes Automatic rivet feed With controller: The brain of every SPR system. It manages, thinks, remembers, and communicates in an Industry 4.0 environment. The lung – small, quiet, and fast rivet feed for your SPR tool. Condition: used Scope of delivery: (See image) (Changes and errors in the technical data are subject to change!) We will gladly answer any further questions you may have over the phone.

Condition: used, Highrise Boltless Pallet Racking With Frame Protectors (Lots 1-9) Dwodpfx Asz Iagbsa Ijc Approx Bay Dimension W2,770 x D980 x H9,000mm

Condition: used, Press capacity: 50 ton Throat depth: 265 mm Stroke: 250 mm Daylight: 400 mm Table surface area : 700 x 450 mm Slide area: 550 x 300 mm Table height over floor: 850 mm Dwedpfx Aswyplcoa Iec Approach speed: 32 mm / sec Working speed: 6,3 mm / sec Return speed: 42 mm / sec Required power: 4 kW Dimensions L x W x H: 1290 x 1160 x 2085 mm Weight of machine approx.: 1,75 ton

Condition: good (used), Zwick / Roell Temperature Chamber for AllroundLine Type: TEE160/LN2 40S The RS simulator model TEE160/LN2 40S is a specialized temperature chamber primarily designed for material testing in combination with ZwickRoell testing machines (especially the AllroundLine). Flexible in Application The innovative temperature chamber from ZwickRoell guarantees a flexible, customized testing system tailored to customer needs without compromise. This ensures reliable test results, even in the future. The safety door function guarantees operator protection in accordance with European safety standards. The chamber door serves as a safety door with a locking mechanism. Precise Temperature Control The temperature chamber creates extremely homogeneous and precise conditions for the test specimens throughout the entire chamber volume. As a result, the test results are accurate and repeatable. Key Specifications Temperature range: -40 °C to +160 °C. Cooling system: Liquid nitrogen (LN2) for high cooling rates. Temperature chamber for the AllroundLine Application: Specifically designed for integration into material testing machines to perform mechanical tests (e.g., tensile or compression tests) under controlled environmental conditions. All sheets in the door area (inside and outside) are made of stainless steel. Solid base frame, demountable Dimensions: W x D x H = 1400 x 600 x 800 mm Chamber: W x D x H = 440 x 530 x 650 mm Test opening: 110 mm Dwsdpfjzcpwpjx Aa Ijc Power supply: 400/230 16A 3N〜50/60Hz Cooling via LN2 (liquid nitrogen) "Everything from a single source: We would be happy to offer you a suitable financing option for your project." You can find more items – new and used – in our shop! International shipping costs on request!

Condition: excellent (used), Year of construction: 1990, Force 25tons Throat 160mm Daylight 500mm Table size 650x650mm Ram size round 140mm Stroke 130mm Dodpfsfcw Apsx Aa Iowc requested power 4 KW Weight 2000Kg height 2100mm width 1100mm depth 1500mm

Condition: used, Year of construction: 2008, functionality: fully functional, manual in images. This is a 5 head horizontal Band Saw. It has tilting heads making it ideal for Feather Edge board production. Dsdpfx Aaozwh Rce Ijwc It has 18KW motors. This machine comes with its own saw sharpening equipment and 10 new blades. All power feed wheels have been replaced with new. It runs on 30mm blades. All new power feed sprockets and fully DC braked.

Condition: excellent (used), Year of construction: 2018, operating hours: 10,000 h, Weinig production line CONTUREX C 125 Year of manufacture: 2018 Approx. 10,000 operating hours Technical data and more images available upon request. Dwodpfx Aaoy Emrkj Iec

Condition: used, Year of construction: 1970, Press capacity: 30 ton Throat depth: 160 Ram stroke adjustable: 20 - 45 mm Slide adjustment: 10 / 60 mm Dodpfxjuqc Eno Aa Iewc Shut height (stroke down, adjustment up): 220 mm Table surface area : 470 x 300 mm Slide area: 250 x 190 mm Number of strokes: 80 - 240 s.p.m. Required power: 4 kW Dimensions L x W x H: 1.400 x 1.800 x 2.000 mm Weight of machine approx.: 2,67 ton Standard configuration the electric is new from 2015.

Condition: good (used), Weiss climate testing chamber with seat pulsator Manufacturer: Weiss Type: SD 1400/+20 DU Test chamber: Material: Stainless steel Dimensions: Height approx. 800 mm Width approx. 2000 mm Depth approx. 900 mm Volume: 1440 liters Outer housing Material: Double-coated Zincor sheet Dimensions: Height approx. 2000 mm Width approx. 2200 mm Depth approx. 2000 mm Dedjxbgrgspfx Aa Ijwc H x W x D 2000 x 2200 x 2000 mm Paint finish: Light grey (RAL 9002) Door, double-leaf: Hinged on the left and right Equipment: Pass-through in the floor and ceiling: 2 each, DN 100 mm, for inserting the pulsation tables Pass-through in the side walls: 1 each, left, right, 100 mm Refrigeration unit: Air-cooled Control: Digital measurement and control system DMR Basic control panel: Integrated into the main switch panel Interface: RS 232 C, for connection to a PC Software: Operating software for MS-Windows Performance data: Temperature range without climate control: +20...+100 °C Temperature stability without climate control: +0.2 … +0.5 K (time-dependent) depending on the range, in the steady state Temperature range with climate control: 20...+95 °C Temperature stability with climate control: +0.2 … +0.5 K (time-dependent) depending on the range, in the steady state Dew point range: 20...+94 °C Humidity range: 10...98 % RH Humidity stability: +3 ... +5 % RH, depending on the range, in the steady state Temperature change rate measured in the outlet without a test specimen and without a load - Cooling: 0.5 K/min. on average, between +100 and +20 °C - Heating: 0.5 K/min. on average, between +20 and +100 °C The performance data refer to an ambient temperature of max. +25 °C and the specified rated voltage For trouble-free operation of the system, the ambient temperature must be between +10 and +35 °C Connections / Other Protection class: IP 32 for the control cabinet Sound pressure level during free-field measurement at a distance of 1 m in front of the device: 60 dB (A) Humidification water: fully demineralized, conductivity max. 20 μS/cm, pH value 6 - 7, automatic topping up Condensate drain: back-pressure-free, 3/4" hose connection Power connection: 400 V; 3 PH+N PE; 50 Hz Connected load: max. 10 KVA Weight: approx. 1160 kg Seat testing device with steel structure for mounting and securing to the climate testing chamber, including: • 2 pneumatic weight lifting devices (150 mm stroke) for test specimen change, 12 weights each weighing 5 kg • 1 base frame in normal steel welded construction for attachment to the underside of the climate testing chamber. This frame is provided on all sides with removable sheets and has 2 folding doors for adjusting the eccentricity. These doors have safety switches. • 2 eccentric disks with bearings and tachometer, 2 connecting rods, 2 ball guides • 2 mounting tables, perforated, 20 mm grid, 650 x 650 mm, for connecting the test specimens, made of aluminum, thickness min. 10 mm • 2 mounting plates, perforated, 20 mm grid, 200 x 200 mm, for connecting the buttocks replica • 2 load rods, 600 mm long, made of stainless steel (The connection to the test specimen is not included in our price, but can be offered subsequently after a precise definition) • 2 three-phase motors, 2 belt drives with tensioning devices • 1 pneumatic control system with 2 manual valves, one filter-regulator unit and one shut-off valve, 1 electrical control cabinet with 2 SEW frequency inverters, hand switch, emergency stop button, 2 push buttons,

Condition: used, COMPLETE BULK MATERIAL PROCESSING & BAGGING PRODUCTION LINE FOR SALE Complete production line suitable for the processing, mixing and bagging of bulk materials including peat, bark, stone, sand and other suitable materials. Dwedpfxez H Ty Eo Aa Ijc The line includes: • B+C form, fill & seal bagging machine • Holding hopper/s • 2 × fertiliser dosing machines • Mixer • Mill • Bag pressing machine • Palletiser • Hooder • Air compressor • Big bag filling machine – adjustable capacity up to approximately 3 cubic metres • Conveyors and associated equipment Located in Ireland outside Rathangan Co. kildare is and available for inspection by appointment. Suitable for businesses involved in bulk material processing, fertiliser, peat, bark, aggregates or similar products. Further technical specifications, dimensions and operating information available on request.

Condition: ready for operation (used), Year of construction: 2004, functionality: fully functional, spindle speed (max.): 6,000 rpm, bar passage: 65 mm, Equipment: bar feeder, chip conveyor, TECHNICAL DETAILS Tool turret Number of turrets: 3 Tool holder: VDI 25 W-gear Main and counter spindle Main and counter spindle speed: up to 6,000 rpm Bar diameter: 65 mm Dwedpfez Ibf Eex Aa Ijc MACHINE DETAILS Coolant tank: 600 l Coolant pressure: 8 / 18 bar EQUIPMENT Gantry removal device Hainbuch HS Axzug / GS Axfix Chip conveyor Coolant tank with strainer basket Coolant pump Coolant cooling unit FMB Turbo 10-65, 3-meter bar feeder

Condition: excellent (used), Sat B2599A Drawer Oven 1000T 130 °C Industrial Oven, Drying Oven When highly diverse products or product components with equally diverse dwell times need to be processed independently in the smallest possible space, drawer ovens are the most sensible and ergonomic solution. Oven Data Manufacturer: Sat Model: B 2599 A Type: 1000T Type: Drawer Oven External Dimensions of the Oven Width with control cabinet: 2500 mm Depth: 1700 mm Height: 2250 mm Usable Volume in Each Drawer Width: 1200 mm Depth: 850 mm Height: 170 mm (measured 178 mm) Maximum Operating Temperature: 130 °C Temperature homogeneity in the usable volume, under stabilized conditions: +/- 3 °C at 80 °C Frame: The basic structure consists of an unalloyed steel framework, on which the outer cladding made of unalloyed steel is mounted and painted in RAL 1013 (pearl white). The oven's inner casing is made of aluminized steel sheet. Insulation between the two oven casings (inner/outer casing) is ensured by 120 mm of rock wool. Floor: Like the oven walls, with 120 mm thick thermal insulation. Height (from factory floor to the first drawer): 800 mm +/- 100 mm, adjustable via the oven feet. Openings: 3 drawers, height 250 mm, for a usable load height of 120 mm. Maintenance Doors: 2-wing maintenance door on the back of the oven. Secured with screws. This door provides complete access to the interior of the oven. Part Handling: Parts are handled via 3 drawers (stacked on top of each other). Height between each drawer: 250 mm Usable height per drawer: 170 mm, with almost 10 mm of clearance. The drawers are smooth and equipped with a sealing strip on the drawer bottom to reduce heat loss when opened. Each drawer has a usable load capacity of 120 kg with load distribution over the entire surface. Peak loads of up to 240 kg can be supported. The drawer seals are made of silicone. The locking mechanisms for each drawer are secured by electromagnets and controlled by the Siemens system. A timer is provided in the control cabinet to control the minimum preheating time for each drawer. A timer is provided in the control cabinet to control the maximum preheating time for each drawer. A temperature indicator is provided for each drawer. These indicators will be located on the front of the oven, to the left of the drawers. Ventilation: Number of circulation fans: 1 Circulation capacity: 4,400 m³/h at 1450 rpm Motor power: 1.5 kW Dwedpfxsim Ik So Aa Ioc Rated voltage: 400 V Rated current: 42 A Power: 24 kW You can find more industrial ovens in other sizes – new and used – in our shop! International shipping costs available upon request!

Condition: used, Year of construction: 1983, machine/vehicle number: 5154, Capacity: 25 ton Throat depth: 250 mm Ram stroke: 6 - 60 mm Slide adjustment: 50 mm Shut height (stroke down, adjustment up): 190 mm Height of the bolster plate: 50 mm Table surface area : 500 x 400 mm Slide area: 350 x 250 mm Tool Clamping Hole Ram: 40 H7 mm Number of strokes: 160 s.p.m. Dimensions L x W x H: 1.300 x 1.500 x 1.995 mm Weight of machine approx.: 2 ton Dsdouqc Hfopfx Aa Iowc Standard configuration Extended machine accessories Press body can be tilt

Condition: excellent (used), Year of construction: 2012, Description Specification Manufacturer TATUNG-OKUMA Model GENOS L300E-M Manufacturing Date 30 January 2012 Serial Number PEA258 CNC Control OKUMA OSP P200LA-R MCS3 Machine Type CNC Turning Centre with Driven Tools CE Declaration of Conformity Available Tool Turret 12 Stations Tailstock Included Parts Catcher Listed in machine documentation Bar Feeder Interface Listed in machine documentation 2. Machining Capacity Description Specification Maximum Turning Diameter Ø300 mm Maximum Turning Length 1,060 mm Maximum Swing Over Bed Ø520 mm X-Axis Travel 235 mm Z-Axis Travel 1,144 mm Main Spindle Speed 30–3,000 rpm Spindle Nose A2-8 Main Spindle Motor Power 11 / 7.5 kW (30 min / continuous) 3. Turret and Driven Tools Description Specification Tool Turret 12 Stations Turret Type M-V12 Driven Tool Capability Yes Driven Tool Speed 45–4,500 rpm Driven Tool Motor Power 7 / 3.3 kW C-Axis 360° C-Axis Indexing Resolution 0.001° 4. Equipment and Features - OKUMA OSP P200LA-R CNC control system Dodpez Nyvtjfx Aa Iewc - 12-station tool turret - Driven tooling capability for milling and drilling operations - C-axis positioning - Tailstock - Parts catcher (indicated in documentation)

Condition: used, Year of construction: 1971, machine/vehicle number: 7130, Capacity: 60 ton Throat depth: 275 mm Ram stroke: 5 -100 mm Shut height (stroke down, adjustment up): 375 mm Table surface area : 740 x 470 mm Number of strokes: 14 - 100 s.p.m. Required power: 10 kW Dodpfxouqcxne Aa Iswc Dimensions L x W x H: 2.300 x 1.500 x 3.000 mm Weight of machine approx.: 3,5 ton

Condition: excellent (used), Year of construction: 2017, operating hours: 7,000 h, functionality: fully functional, machine/vehicle number: 25787, travel distance X-axis: 800 mm, travel distance Y-axis: 700 mm, travel distance Z-axis: 500 mm, spindle speed (max.): 18,000 rpm, operating hours of spindle: 6,900 h, Equipment: chip conveyor, documentation/manual, Hermle C 400 U – 5-Axis Machining Center Year: 2017 Control: Heidenhain TNC 640 Condition: Very good Machine ON: 18,512 h Program: 9,268 h Spindle ON: 6,900 h Drive ON: 18,514 h Axes in motion: 7,147 h Technical specifications: X/Y/Z travel: 850 / 700 / 500 mm A-axis: 25 rpm C-axis: 30 rpm Spindle speed: up to 18,000 rpm Power: 20 kW Dsdpjz H Agbjfx Aa Iswc Torque: 173 Nm Tool holder: HSK 63 Tool magazine: 38 + 50 positions NC swivel rotary table: Ø 650 mm Swivel range: +91° to −139° Equipment: Heidenhain touch probe BLUM tool measurement Electronic handwheel Chip conveyor Oil mist extraction Inspection possible by appointment.

Condition: excellent (used), Year of construction: 2017, POSmill C 800 Compact – CNC machining center – Year of manufacture 2017 – Heidenhain TNC 620 Technical data: - Manufacturer: POSmill - Model: C 800 Compact - Year of manufacture: 2017 - Control system: Heidenhain TNC 620 - Travel in X: 800 mm - Travel in Y: 520 mm - Travel in Z: 550 mm - Table size: 950 × 520 mm - Spindle speed: max. 10,000 rpm - Tool holder: SK 40 - Tool changer: 24-position (subject to confirmation) Dodsz Ny H Ejpfx Aa Iewc - Machine weight: approx. 6,800 kg - Rated power: 25 kVA Operating hours: - Control system on: approx. 35,524 hours - Machine on: approx. 29,264 hours - Program run: approx. 14,359 hours - Spindle S1: approx. 11,651 hours Further information and viewings by appointment.

Condition: used, Year of construction: 2020, total length: 3,000 mm, total width: 1,300 mm, total height: 1,900 mm, Veneer press Manufacturer: Stema S.r.L. Type: P – 90 C Year of manufacture: 2020 Dimensions (l/w/h): 3,000 x 1,300 x 1,900 Weight: approx. 3,800 kg Pressing force / pressure: 70 – 90 t Djdpfoz Ip H Rex Aa Iswc Purchase price (net): €16,000 plus applicable VAT. VAT will be shown separately on our invoice. Note: The equipment description is taken from the original purchase invoice and has not been checked for accuracy or completeness. Deviations are possible! Financing possible Upon request, we can arrange suitable financing through our company. Please do not hesitate to contact us. Subject to changes, errors and prior sale. Sale is made without guarantee or warranty and only to commercial businesses. Inquiries will be processed from Monday to Friday between 8 a.m. and 4 p.m.

Condition: excellent (used), Carbolite CWF 11/5 Chamber Furnace, 1100 °C Max. Temperature: 1100 °C With extraction system and table The upward-opening door keeps the hot surface away from the user. Gentle, self-closing door. Carbolite Gero 301 controller with ramp, setpoint, and process timer functions (CWF & CWF-B). Durable alumina support plates for the heating elements; robust door frame and base plate. High-quality fiber insulation with low thermal mass. Powerful heating elements on both sides ensure very good temperature homogeneity. Easy access to elements and the control system simplifies maintenance and servicing. Volume (liters): 5 Dwedopygpfspfx Aa Iec Maximum temperature (°C): 1100 Heating time (min): 47 Continuous operating temperature (°C): 1000 Max. power (W): 2400 Holding power (W): 790 Thermocouple type: R Dimensions: Internal dimensions H x W x D (mm): 135 x 140 x 250 External dimensions H x W x D (mm): 585 x 375 x 485 External dimensions with door open H x W x D (mm): 800 x 375 x 485 Homogeneous temperature zone (±5°C) H x W x D (mm): 85 x 90 x 110 Weight (kg): 30 Connection: 230 V, 50 Hz, 2.4 kW Table: H x W x D (mm): 750 x 650 x 740 Extraction system: H x W x D (mm): 1020 x 720 x 540 More new and used items can be found in our shop! International shipping costs available upon request!